SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
Cautions
•This unit is designed for negative earth 12 V
DC operation only.
•Do not get the leads under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all earth leads to a common earth
point.
•Be sure to insulate any loose unconnected
leads with electrical tape for safety.
Notes on the power supply lead (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
•The numbers in the list are keyed to those in
the instructions.
•The bracket 1 and the protection collar 5 are
attached to the unit before shipping. Before
mounting the unit, use the release keys 6 to
remove the bracket 1 and the protection collar
5 from the unit. For details, see “Removing
the protection collar and the bracket (4)” on
the reverse side of the sheet.
• Keep the release keys 6 for future use as
they are also necessary if you remove the
unit from your car.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
Note
Before installing, make sure that the catches on
both sides of the bracket 1 are bent inwards 2 mm.
If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
Connection example (2)
Notes (2-B)
• Be sure to connect the earth lead before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Connection diagram (3)
1 To a metal surface of the car
First connect the black earth lead, then connect
the yellow and red power input leads.
2 To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
•It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/AM aerial in
the rear/side glass, see “Notes on the control
and power supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the +12 V power terminal which is energised
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black earth lead to a
metal surface of the car first.
• When your car has a built-in FM/AM aerial in
the rear/side glass, see “Notes on the control
and power supply leads.”
5 To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth lead to a
metal surface of the car first.
3-261-419-11 (1)
Installation/Connections
© 2004 Sony Corporation Printed in Thailand
1
12
× 4
3
4675
× 2
Equipment used in illustrations (not supplied)
Power amplifier
Front speaker
Rear speaker
2
B
A
FM/AM
Compact Disc
Player
CDX-R3300T
CDX-R3000T
Rotary commander RM-X4S
Active subwoofer
AUDIO OUT REAR
1
Catch
SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
BUS
AUDIO
IN
L
R
AUDIO
OUT
REAR
L
R
REMOTE IN
AUDIO OUT REAR
*
from car aerial
2
5
4
AMP REM
7
Left
Right
Left
Right
RCA pin cord (not supplied)
Max. supply current 0.3 A
Max. supply current 0.1 A
Fuse (10 A)
Red
Yellow
Black
Blue
Blue/white striped
White
Green
Purple
White/black striped
Grey/black striped
Green/black striped
Purple/black striped
Grey
•
•
•
•
•
•
•
•
1
•
• 1 5
6
1 5
4
•
6
1
1
2
2-B
•
•
3
1
2
•
•
3
4
•
•
5
•
•
•
3
1
ANT REM
1
3
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM aerial in the
rear/side glass, connect the power aerial control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing aerial
booster. For details, consult your dealer.
•A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker leads installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker leads to each
other.
Note on connection
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case, make
sure the speaker and amplifier are connected
correctly.
•
•
•
•
•
•
•
•
* AUDIO OUT can be switched to
REAR or SUB.
For details, see the supplied
operating instructions.
Insert with the cord upwards.
SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
O
PEN/EJEC
T
182 mm
53 mm
6 A
to dashboard/centre console
Bracket
Bracket
max. size
5 × 8 mm
B
4
max. size
5 × 8 mm
TOYOTA
NISSAN
4
to dashboard/centre console
Bracket
Bracket
4
Existing parts supplied with your car
max. size
5 × 8 mm
max. size
5 × 8 mm
7 AB
1 2
2
5
3
1
1
Fire wall
Dashboard
5
3
4
4
1
2
6
5
6
ccc
1
Existing parts supplied with your car
(OFF)
Claws
Orient the release key
collectly.
Face the hook inwards.
OPEN/EJECT
SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
SONY CDX-R3300T/R3000T (GB,CT) 3-261-419-11 (1)
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Removing the protection collar
and the bracket (4)
Before installing the unit, remove the
protection collar 5 and the bracket 1 from
the unit.
1 Remove the protection collar 5.
1 Engage the release keys 6 together with
the protection collar 5.
2 Pull out the release keys 6 to remove the
protection collar 5.
2 Remove the bracket 1.
1 Insert both release keys 6 together
between the unit and the bracket 1 until
they click.
2 Pull down the bracket 1, then pull up the
unit to separate.
Mounting example (5)
Installation in the dashboard
Notes
• Bend these claws outwards for a tight fit, if
necessary. (5-2)
• Make sure that the 4 catches on the protection
collar 5 are properly engaged in the slots of the
unit. (5-3)
Mounting the unit in a Japanese
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 4.
How to detach and attach the
front panel (7)
Before installing the unit, detach the front
panel.
7-A To detach
Before detaching the front panel, be sure to
press (OFF). Press , then pull it off towards
you.
7-B To attach
Attach part A of the front panel to part B of the
unit as illustrated and push the left side into
position until it clicks.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
After tuning off the ignition, be sure to
press and hold (OFF) on the unit until the
display disappears.
Otherwise, the display does not turn off and this
causes battery drain.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc., after detaching the
front panel.
•
•
•
4
5
1
5
1 6 5
2 6 5
1
1 6 1
2 1
5
• 5
•
5
5
6
4
7
7
(OFF)
7
A B
(OFF)
-
1
-
2
-
3
-
4
