KDL-50W800B / 50W700B / 42W800B / 42W700B / 32W700B
Television
Reference Guide
GB
CT
2
GB
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting Other Devices. . . . . . . . . . . . . 7
Installing the TV to the Wall . . . . . . . . . . . 8
Installing the Brackets on the wall . . . . . . . . 9
Preparing for the installation of the TV . . . 12
Installing the TV on the wall . . . . . . . . . . . . 13
Troubleshooting . . . . . . . . . . . . . . . . . . . . 15
Troubles and Solutions . . . . . . . . . . . . . . . . 15
Specifications . . . . . . . . . . . . . . . . . . . . . . 16
Introduction
Thank you for choosing this Sony product.
Before operating the TV, please read this manual thoroughly and
retain it for future reference.
Note
• Before operating the TV, please read “Safety Information”
(page 2).
• Instructions about “Installing the TV to the Wall” are included
within this TV’s instructions manual.
• Images and illustrations used in Quick Start Guide and this
manual are for reference only and may differ from actual
product appearance.
Location of the identification label
Labels for the TV Model No. and Power Supply rating are located
on the rear of the TV.
Labels for the AC adapter Model No. and Serial No. are located on
the bottom of the AC adapter.
WARNING
Batteries must not be exposed to excessive heat such as
sunshine, fire or the like.
Installation/Set-up
Install and use the TV set in accordance with the instructions
below in order to avoid any risk of fire, electrical shock or damage
and/or injuries.
Installation
• The TV set should be installed near an easily accessible AC
power outlet (mains socket).
• Place the TV set on a stable, level surface to avoid it from falling
down and cause personal injury or damage to the TV.
• Only qualified service personnel should carry out wall
installations.
• For safety reasons, it is strongly recommended that you use
Sony accessories, including:
Wall-Mount Bracket
• Be sure to use the screws supplied with the Wall-Mount Bracket
when attaching the Mounting Hook (Stand) to the TV set. The
supplied screws are designed as indicated by illustration when
measured from the attaching surface of the Mounting Hook
(Stand).
The diameter and length of the screws differ depending on the
Wall-Mount Bracket model.
Use of screws other than those supplied may result in internal
damage to the TV set or cause it to fall, etc.
This television is designed for use in Hong Kong and ensured
the usage in Hong Kong only.
Safety Information
Screw (supplied with the
Wall-Mount Bracket)
Mounting Hook (Stand)
Hook attachment on rear
of TV set
7 mm
3
GB
GB
Transporting
• Before transporting the TV set, disconnect all cables.
• Two or three people are needed to transport a large TV set.
• When transporting the TV set by hand, hold it as shown below.
Do not put stress on the LCD panel and the frame around the
screen.
• When transporting the TV set, do not subject it to jolts or
excessive vibration.
• When transporting the TV set for repairs or when moving, pack
it using the original carton and packing material.
Topple prevention
• Before install the machine screw, lay the display face down on a
stable work surface that is larger than the TV.
• To prevent damaging the surface of the LCD display, make sure
to place a soft cloth on the work surface.
Ventilation
• Never cover the ventilation holes or insert anything in the
cabinet.
• Leave space around the TV set as shown below.
• It is strongly recommended that you use a Sony Wall-Mount
Bracket in order to provide adequate air-circulation.
Installed on the wall
Installed with stand
• To ensure proper ventilation and prevent the collection of dirt or
dust:
Do not lay the TV set flat, install upside down, backwards, or
sideways.
Do not place the TV set on a shelf, rug, bed or in a closet.
Do not cover the TV set with a cloth, such as curtains, or items
such as newspapers, etc.
Do not install the TV set as shown below.
AC power cord (mains lead)
Handle the AC power cord (mains lead) and outlet (mains socket)
as follows in order to avoid any risk of fire, electrical shock or
damage and/or injuries:
Use only Sony supplied AC power cords (mains lead), not those
of other brands.
Insert the plug fully into the AC power outlet (mains socket).
Operate the TV set on a 220–240 V AC supply only.
When wiring cables, be sure to unplug the AC power cord
(mains lead) for your safety and take care not to catch your feet
on the cables.
Disconnect the AC power cord (mains lead) from the AC power
outlet (mains socket) before working on or moving the TV set.
Keep the AC power cord (mains lead) away from heat sources.
Unplug the AC power plug (mains plug) and clean it regularly. If
the plug is covered with dust and it picks up moisture, its
insulation may deteriorate, which could result in a fire.
Note
• Do not use the supplied AC power cord (mains lead) on any
other equipment.
• Do not pinch, bend, or twist the AC power cord (mains lead)
excessively. The core conductors may be exposed or broken.
• Do not modify the AC power cord (mains lead).
• Do not put anything heavy on the AC power cord (mains lead).
• Do not pull on the AC power cord (mains lead) itself when
disconnecting the AC power cord (mains lead).
• Do not connect too many appliances to the same AC power
outlet (mains socket).
• Do not use a poor fitting AC power outlet (mains socket).
NOTE ON AC ADAPTER
Warning
To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
To prevent fire or shock hazard, do not place objects filled with
liquids, such as vases, on the apparatus.
Do not install this equipment in a confined space, such as a
bookshelf or similar unit.
• Please ensure that the AC power outlet (mains socket) is
installed near the equipment and shall be easily accessible.
• Be sure to use the supplied AC adapter and AC power cord
(mains lead). Otherwise it may cause a malfunction.
• Connect the AC adapter to an easily accessible AC power outlet
(mains socket).
• Do not coil the AC power cord (mains lead)
around the AC adapter. The core wire may
be cut and/or it may cause a malfunction
of the TV.
• Do not touch the AC adapter with wet hands.
• If you notice an abnormality in the AC adapter, disconnect it
from the AC power outlet (mains socket) immediately.
• The set is not disconnected from the AC source as long as it is
connected to the AC power outlet (mains socket), even if the set
itself has been turned off.
• As the AC adapter will become warm when it is used for a long
time, you may feel hot when touching it by hand.
30 cm
10 cm
10 cm
10 cm
Leave at least this space around the set.
30 cm
10 cm
10 cm
Leave at least this space around the set.
6 cm
Air circulation is blocked.
Wall Wall
4
GB
Prohibited Usage
Do not install/use the TV set in locations, environments or
situations such as those listed below, or the TV set may
malfunction and cause a fire, electrical shock, damage and/or
injuries.
Location:
• Outdoors (in direct sunlight), at the seashore, on a ship or other
vessel, inside a vehicle, in medical institutions, unstable
locations, near water, rain, moisture or smoke.
• If the TV is placed in the changing room of
a public bath or hot spring, the TV may be
damaged by airborne sulphur, etc.
• For best picture quality, do not expose the screen to direct
illumination or sunlight.
• Avoid moving the TV from a cold area to a warm area. Sudden
room temperature changes may cause moisture condensation.
This may cause the TV to show poor picture and/or poor colour.
Should this occur, allow moisture to evaporate completely
before powering the TV on.
Environment:
• Places that are hot, humid, or excessively dusty; where insects
may enter; where it might be exposed to mechanical vibration,
near flammable objects (candles, etc.). The TV set shall not be
exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the TV.
• Do not place the TV in a humid or dusty
space, or in a room with oily smoke or
steam (near cooking tables or
humidifiers). Fire, electric shock, or
warping may result.
• Do not install the TV in places subject to extreme temperature,
such as in direct sunlight, near a radiator or a heating vent. The
TV may overheat in such conditions which can cause
deformation of the enclosure and/or TV malfunction.
Situation:
• Do not use when your hands are wet, with the cabinet removed,
or with attachments not recommended by the manufacturer.
Disconnect the TV set from AC power outlet (mains socket) and
antenna during lightning storms.
• Do not install the TV so that it sticks out
into an open space. Injury or damage
from a person or object bumping into
the TV may result.
Broken pieces:
• Do not throw anything at the TV set. The screen glass may break
by the impact and cause serious injury.
• If the surface of the TV set cracks, do not touch it until you have
unplugged the AC power cord (mains lead). Otherwise electric
shock may result.
When not in use
• If you will not be using the TV set for several days, the TV set
should be disconnected from the AC power (mains) for
environmental and safety reasons.
• As the TV set is not disconnected from the AC power (mains)
when the TV set is just turned off, pull the plug from the AC
power outlet (mains socket) to disconnect the TV set
completely.
• However, some TV sets may have features that require the TV
set to be left in standby to work correctly.
For children
• Do not allow children to climb on the TV set.
• Keep small accessories out of the reach of children, so that they
are not mistakenly swallowed.
If the following problems occur...
Turn off the TV set and unplug the AC power cord (mains lead)
immediately if any of the following problems occur.
Ask your dealer or Sony service centre to have it checked by
qualified service personnel.
When:
AC power cord (mains lead) is damaged.
Poor fitting of AC power outlet (mains socket).
TV set is damaged by being dropped, hit or having something
thrown at it.
Any liquid or solid object falls through openings in the cabinet.
About LCD Monitor Temperature
When the LCD Monitor is used for an extended period, the panel
surrounds become warm. You may feel hot when touching there
by the hand.
WALL-MOUNT BRACKET
Below information shows the correct handling of the Wall-Mount
Bracket. Be sure to read this information thoroughly and use the
Wall-Mount Bracket correctly.
To Customers:
Be sure to observe the following precautions for safety to prevent
a serious injury through fire, electric shock, the product toppling
over, or the product dropping.
• Be sure to subcontract the installation to licensed contractors
and keep small children away during installation.
• Be sure to subcontract moving or dismounting of the TV to
licensed contractors.
• Do not remove screws, etc., after mounting the TV.
• Do not make alterations to the parts of the Wall-Mount Bracket.
• Do not mount any equipment other than the specified product.
• Do not apply any load other than the TV on the Wall-Mount
Bracket.
• Do not lean on or hang from the TV.
• Do not handle the TV with excessive force during cleaning or
maintenance.
To Sony Dealers and Contractors:
The following instructions are for Sony dealers and contractors
only. Be sure to read safety precautions described below and pay
special attention to safety during the installation, maintenance
and checking of this product.
• When handling or mounting the TV set, hold it on the sides. Do
not lift the TV by the Stand.
• Do not install the Wall-Mount Bracket on
wall surfaces where the corners or the
sides of the TV are protruding away from
the wall surface.
Stand Stand
5
GB
GB
• Do not install the TV over or under an air conditioner.
• Be sure to install the Wall-Mount Bracket
securely to the wall following the instructions in
this instruction manual. If any of the screws are
loose or fall out, the Wall-Mount Bracket may
fall and cause injury or property damage.
• Be sure to use the supplied screws and
attachment parts properly following the
instructions given in this instruction manual. If
you use substitute items, the TV may fall and
cause bodily injury to someone or damage to the TV.
• Be sure to assemble the bracket properly following the
instructed procedure explained in this instruction manual.
• Be sure to tighten the screws securely in the designated
position.
• Be careful not to subject the TV to shock during installation.
• Be sure to install the TV on a wall that is both perpendicular and
flat.
• After proper installation of the TV, secure the cables properly.
• Do not allow the AC power cord (mains
lead) or the connecting cables to be
pinched as the internal conductors may
become exposed and cause a short
circuit or an electrical break.
Viewing the TV
• Some people may experience discomfort (such as eye strain,
fatigue, or nausea) while watching 3D video images or playing
stereoscopic 3D games. Sony recommends that all viewers take
regular breaks while watching 3D video images or playing
stereoscopic 3D games. The length and frequency of necessary
breaks will vary from person to person. You must decide what
works best. If you experience any discomfort, you should stop
watching the 3D video images or playing stereoscopic 3D
games until the discomfort ends; consult a doctor if you believe
necessary. You should also review (i) the instruction manual of
any other device or media used with this television and (ii) our
website (http://www.sony-asia.com/support) for the latest
information. The vision of young children (especially those
under six years old) is still under development. Consult your
doctor (such as a paediatrician or eye doctor) before allowing
young children to watch 3D video images or play stereoscopic
3D games. Adults should supervise young children to ensure
they follow the recommendations listed above.
• Do not use, store, or leave the 3D Glasses or battery near a fire,
or in places with a high temperature, e.g., in direct sunlight, or
in sun-heated cars.
• When using the simulated 3D function, please note that the
displayed image is modified from the original due to the
conversion done by this television.
• View the TV in moderate light, as viewing the TV in poor light or
during long period of time, strains your eyes.
• When using headphones, adjust the volume so as to avoid
excessive levels, as hearing damage may result.
LCD Screen
• Although the LCD screen is made with high-precision
technology and 99.99% or more of the pixels are effective, black
dots may appear or bright points of light (red, blue, or green)
may appear constantly on the LCD screen. This is a structural
property of the LCD screen and is not a malfunction.
• Do not push or scratch the front filter, or place objects on top of
this TV set. The image may be uneven or the LCD screen may be
damaged.
• If this TV set is used in a cold place, a smear may occur in the
picture or the picture may become dark. This does not indicate a
failure. These phenomena disappear as the temperature rises.
• Ghosting may occur when still pictures are displayed
continuously. It may disappear after a few moments.
• The screen and cabinet get warm when this TV set is in use. This
is not a malfunction.
• The LCD screen contains a small amount of liquid crystal. Follow
your local ordinances and regulations for disposal.
Handling and cleaning the screen surface/
cabinet of the TV set
Be sure to unplug the AC power cord (mains lead) connected to
the TV set from AC power outlet (mains socket) before cleaning.
To avoid material degradation or screen coating degradation,
observe the following precautions.
• To remove dust from the screen surface/cabinet, wipe gently
with a soft cloth. If dust is persistent, wipe with a soft cloth
slightly moistened with a diluted mild detergent solution.
• Never spray water or detergent directly on
the TV set. It may drip to the bottom of the
screen or exterior parts and enter the TV set,
and may cause damage to the TV set.
• Never use any type of abrasive pad, alkaline/acid cleaner,
scouring powder, or volatile solvent, such as alcohol, benzene,
thinner or insecticide. Using such materials or maintaining
prolonged contact with rubber or vinyl materials may result in
damage to the screen surface and cabinet material.
• Periodic vacuuming of the ventilation openings is
recommended to ensure to proper ventilation.
• When adjusting the angle of the TV set, move it slowly so as to
prevent the TV set from moving or slipping off from its table
stand.
Optional Equipment
Keep optional components or any equipment emitting
electromagnetic radiation away from the TV set. Otherwise
picture distortion and/or noisy sound may occur.
Wireless Function of the unit
• Do not operate this unit near medical equipment (pacemaker,
etc.), as malfunction of the medical equipment may result.
• Although this unit transmits/receives scrambled signals, be
careful of unauthorised interception. We cannot be responsible
for any trouble as a result.
Caution about handling the remote control
• Observe the correct polarity when inserting batteries.
• Do not use different types of batteries together or mix old and
new batteries.
• Dispose of batteries in an environmentally friendly way. Certain
regions may regulate the disposal of batteries. Please consult
your local authority.
• Handle the remote control with care. Do not drop or step on it,
or spill liquid of any kind onto it.
• Do not place the remote control in a location near a heat source,
a place subject to direct sunlight, or a damp room.
Precautions
6
GB
WALL-MOUNT BRACKET
• If you use the TV installed on the Wall-Mount Bracket for a long
time, the wall behind or above the TV may become discoloured
or the wallpaper may come unglued, depending on the material
of the wall.
• If the Wall-Mount Bracket is removed after installing it on the
wall, the screw holes remain.
• Do not use the Wall-Mount Bracket in a place where it is
subjected to mechanical vibration.
7
GB
GB
Connecting Other Devices
To connect with an HDMI cable
To connect with component cables
To connect with AV composite cables
To HDMI OUT
< 21 mm
< 12 mm
To AUDIO OUT To COMPONENT
OUT (P
R/PB/Y)
To VIDEO OUT
SD HD
Picture Quality
• AV composite cable
•Antenna cable
Standard definition (SD) videos have picture signals with a
vertical resolution of 480 (NTSC) or 576 (PAL/SECAM) lines.
• Component cable • HDMI cable
High definition (HD) videos have picture signals
with a vertical resolution of 720 or 1080 lines.
8
GB
Installing the TV to the Wall
Your TV’s Table-Top Stand will be used as a part of the Wall-Mount Bracket.
Note
• See page 2 (Safety Information) and page 5 (Precautions) on WALL-MOUNT BRACKET before carrying out Wall-Mount
Bracket installation.
• If the Table-Top Stand is attached to the TV, detach the Table-Top Stand beforehand.
• Place the TV with its screen facing down on a flat and stable surface covered with a thick and soft cloth that is larger
than the TV, when securing the Stand or when removing the Table-Top Stand from the TV to prevent damaging the
surface of the LCD display.
• Once the Stand Necks are detached from the Stand, be sure to keep the Stand Necks and screws in a safe place.
• When attaching the Table-Top Stand again, be sure to fasten the screws (previously removed) to the original holes
on the rear of the TV.
To detach the Table-Top Stand from the TV
To Customers
Sufficient expertise is required for installing this product. Be sure to subcontract the installation to Sony
dealers or licensed contractors and pay special attention to safety during the installation. Sony is not liable
for any damages or injury caused by mishandling or improper installation, or installing any other than the
specified product. Your Statutory Rights (if any) are not affected.
To Sony Dealers and Contractors
Sufficient expertise is required for installing this product. Be sure to read this instruction manual thoroughly
to do the installation work safely. Sony is not liable for any damages or injury caused by mishandling or
improper installation.
Soft cloth
Stand Necks
Stand
9
GB
GB
1 Prepare necessary items.
Wall-Mount Bracket accessories (supplied)
Stand (supplied)
Screw for Wall-Mount Base (8 mm in diameter, not supplied)
KDL‐50W800B, KDL‐50W700B (8)
KDL-42W800B, KDL-42/32W700B (4)
Installing the Brackets on the wall
A Paper Template B Wall-Mount Base
KDL‐50W800B,
KDL‐50W700B (2)
KDL-42W800B,
KDL‐42/32W700B (1)
C Stand Protector
KDL‐50W800B,
KDL‐50W700B (2)
KDL-42W800B,
KDL‐42/32W700B (1)
D Screw (+PSW 6 × 12) (2)
E Spacer (2) F Bracket Cap Plate
KDL‐50W800B,
KDL‐50W700B (2)
KDL-42W800B,
KDL‐42/32W700B (1)
G Screw (+PSW 4 × 10)
KDL‐50W800B,
KDL‐50W700B (2)
KDL-42W800B,
KDL‐42/32W700B (1)
H
10
GB
2 Make sure that the wall has enough space for the TV and is capable of supporting a
weight of at least four times that of the TV.
Refer to the following table on installing the TV to the wall. See page 16-18 (Specifications)
for the TV’s weight.
KDL‐50W800B, KDL‐50W700B
KDL-42W800B, KDL-42/32W700B
Unit: mm
Note
• Figures in the table may differ slightly depending on the installation.
Model Name
KDL-
Display dimensions Screen centre dimension Length for mounting
50W800B/
50W700B
1,116 656 130 469 118
42W800B/
42W700B
958 563 175 465 118
32W700B 729 433 188 413 113
Screen centre point
Screen centre point
11
GB
GB
3 Make a mark on the Paper Template A that indicates the centre of the screen for your TV.
4 Tape the Paper Template A to the wall and drill holes according to the numbering on the
Paper Template A using an electric drill.
5 Remove the Paper Template A off from the wall.
6 Attach the Wall-Mount Base B to the wall correctly using the screws (8 mm in diameter,
not supplied).
100
150
200
250
100
150
200
250
100
150
200
250
KDL‐50W800B, KDL‐50W700B
Scale on Paper Template A
KDL-42W800B, KDL-42/32W700B
Scale on Paper Template A
Mark for KDL-32W700B
Mark for KDL-42W800B,
KDL-42W700B
Mark for KDL‐50W800B, KDL‐50W700B
30
1
2
3
4
10
0
50
100
150
200
250
300
350
30
5
6
7
8
20
10
0
50
100
150
200
250
300
350
1, 2, 3, 4
20
5, 6, 7, 8
30
1
2
3
4
20
10
0
50
100
150
200
250
300
350
1, 2, 3, 4
KDL‐50W800B, KDL‐50W700B KDL-42W800B, KDL-42/32W700B
Wall
Wall
A
A
KDL‐50W800B, KDL‐50W700B KDL-42W800B, KDL-42/32W700B
12
GB
1 Remove screws from the rear of the TV. Be sure to store the removed screws in a safe
place, keeping them away from children.
2 Insert the pin (on the Stand Protector C) into the hole on the Stand H, then fold up the
Stand Protector C. Confirm the Stand Protector C is firmly latched to the Stand H.
3 Attach the Stand H to the TV using the supplied screws D. Attach the Spacers E to the
holes indicated by the triangle marks
f
. KDL‐50W800B, KDL‐50W700B is used for
illustration purpose.
Preparing for the installation of the TV
Soft cloth
H
C
H
C
KDL‐50W800B, KDL‐50W700B KDL-42W800B, KDL-42/32W700B
Pin
H
D
E
×
2
Soft cloth
13
GB
GB
1 Make sure to connect and bundle the cables before installing the TV on the wall.
2 Install the TV on the wall. Then, confirm the Stand Protector C is firmly latched into the
Wall-Mount Base B and the Spacers E touch the wall. Attach the Bracket Cap Plate F
using the supplied screws G.
Installing the TV on the wall
B
1
2
1
2
G
C
C
B
B
F
G
F
B
E
Wall
KDL‐50W800B, KDL‐50W700B
KDL-42W800B, KDL-42/32W700B
Wall
14
GB
Dimensions of the hole positions on the wall
Provide the following information to the licensed contractors if necessary.
Use screws (8 mm in diameter, not supplied) to install the Wall-Mount Base B on the wall.
Be sure to use the supplied Paper Template A that shows the actual position of Wall-Mount Base B
for easy installation.
KDL‐50W800B, KDL‐50W700B
KDL-42W800B, KDL-42/32W700B
BB
176 mm
76 mm 76 mm
28 mm 28 mm
B
28 mm
76 mm
15
GB
GB
Troubleshooting
When the illumination LED is flashing red,
count how many times it flashes (interval
time is three seconds).
If the illumination LED flashes red, reset the TV
by disconnecting the AC power cord (mains
lead) from the TV for two minutes, then turn on
the TV.
If the problem persists, contact your dealer or
Sony service centre with the number of times
the illumination LED flashes red (interval time is
three seconds). Press / on the TV to turn it
off, disconnect the AC power cord (mains lead),
and inform your dealer or Sony service centre.
When the illumination LED is not flashing,
check the items as follows.
You can also refer to [Troubleshooting] in the
i-Manual or perform self-diagnosis by selecting
[Help] [Customer Support] [Self
Diagnostics]. If the problem persists, have your
TV serviced by qualified service personnel.
Troubles and Solutions
There is no picture (screen is dark) and no
sound.
Check the antenna (aerial)/cable connection.
Connect the TV to the AC power (mains), and
press / on the TV or remote control.
Some programmes cannot be tuned.
Check the antenna (aerial).
The remote control does not function.
Replace the batteries.
Your TV may be in SYNC mode.
Press SYNC MENU, select [TV Control] and then
select [Home (Menu)] or [Options] to control the
TV.
The [Parental Lock] password has been
forgotten.
Enter 9999 for the PIN code. (PIN code 9999 is
always accepted.)
The TV surrounds become warm.
When the TV is used for an extended period, the
TV surrounds become warm.
You may feel hot when touching there by the
hand.
Frozen audio or video, a blank screen, or the
TV does not respond to TV or remote control
buttons.
Perform a simple reset of the TV by unplugging
the AC power cord (mains lead) for two minutes,
then plug it in again.
The /, CH+/–, +/–, ///, , and
HOME buttons cannot be located on the TV.
See below illustration for location of the buttons
on the TV.
The illumination LED is turned on.
If you do not wish to light up the illumination LED,
you can turn it off.
Press HOME, then select [Settings] t
[System Settings] t [General Set-up] t
[Illumination LED] t [Off]. You can also press
OPTIONS, then select [Illumination LED] t [Off].
Cannot connect to a wireless router by WPS.
If you use WEP security, select [Easy] t [Wi-Fi] t
[Connect by scan list]. Then, select the network
name (SSID) you want to connect.
Cannot find the required network name in
network setup.
Select [[Manual Entry]] and press to enter
network name.
Rear of TV
16
GB
Specifications
System
Panel system
LCD (Liquid Crystal Display) Panel, LED backlight
TV system
Analogue: B/G, I, D/K, M, L
Digital: DTMB
Colour/video system
Analogue: PAL, SECAM, NTSC3.58, NTSC4.43
Digital: Refer to the i-Manual
Channel coverage
Analogue: UHF/VHF/Cable
Digital: UHF
Sound output
8 W + 8 W (KDL-50/42W800B, KDL-50/42W700B)
5 W + 5 W (KDL-32W700B)
Wireless technology
Protocol IEEE802.11a/b/g/n
Input/Output jacks
Antenna (aerial)/cable
75 ohm external terminal for VHF/UHF
/ VIDEO IN 1
Video/Audio input (phono jacks)
/ COMPONENT IN
YPBPR (Component Video): 1080p (50, 60 Hz),
1080i (50, 60 Hz), 720p (50, 60 Hz), 576p, 576i,
480p, 480i
Audio input (phono jacks)
VIDEO IN 2
Video input (common phono pin with Y input)
HDMI IN 1, 2, 3, 4 (KDL-50/42W800B only)
Video (2D): 1080p (30, 50, 60 Hz), 1080/24p, 1080i
(50, 60 Hz), 720p (30, 50, 60 Hz), 720/24p, 576p,
576i, 480p, 480i, PC Formats
Video (3D):
Frame Packing: 1080p (30 Hz), 1080/24p,
1080i (50, 60 Hz), 720p (30, 50, 60 Hz), 720/24p
Side-by-Side: 1080p (50, 60 Hz), 1080/24p,
1080i (50, 60 Hz), 720p (50, 60 Hz)
Over-Under: 1080p (30, 50, 60 Hz), 1080/24p,
1080i (50, 60 Hz), 720p (50, 60 Hz)
Audio: 5.1 channel linear PCM: 32, 44.1 and
48 kHz, 16, 20 and 24 bits, Dolby Digital
ARC (Audio Return Channel) (HDMI IN 2 only)
HDMI IN 1, 2, 3, 4 (except KDL-50/42W800B)
Video: 1080p (30, 50, 60 Hz), 1080/24p,
1080i (50, 60 Hz), 720p (30, 50, 60 Hz),
720/24p, 576p, 576i, 480p, 480i, PC Formats
Audio: 5.1 channel linear PCM: 32, 44.1 and
48 kHz, 16, 20 and 24 bits, Dolby Digital
ARC (Audio Return Channel) (HDMI IN 2 only)
MHL (common with HDMI IN 1)
(KDL-50/42W800B only)
Video (2D): 1080p (30 Hz), 1080/24p,
1080i (50, 60 Hz), 720p (30, 50, 60 Hz),
720/24p, 576p, 576i, 480p, 480i
Video (3D):
Side-by-Side: 1080/24p, 1080i (50, 60 Hz),
720p (50, 60 Hz)
Over-Under: 1080p (30 Hz), 1080/24p,
1080i (50, 60 Hz), 720p (50, 60 Hz)
Audio: 5.1 channel linear PCM: 32, 44.1 and
48 kHz, 16, 20 and 24 bits, Dolby Digital
MHL (common with HDMI IN 1)
(except KDL-50/42W800B)
Video: 1080p (30 Hz), 1080/24p, 1080i (50, 60 Hz),
720p (30, 50, 60 Hz), 720/24p, 576p, 576i, 480p,
480i
Audio: 5.1 channel linear PCM: 32, 44.1 and
48 kHz, 16, 20 and 24 bits, Dolby Digital
DIGITAL AUDIO OUT (OPTICAL)
Digital optical jack (Two channel linear PCM,
Dolby Digital)
HDMI 3 AUDIO IN
Analogue audio input (stereo minijack)
AUDIO OUT/
Audio output (stereo minijack)
Headphones jack
(supports Subwoofer out)
1, 2
USB port
DC IN 19.5 V
AC adapter input
LAN
10BASE-T/100BASE-TX connector (Depending on
the operating environment of the network,
connection speed may differ. 10BASE-T/100BASE-
TX communication rate and communication
quality are not guaranteed for this TV.)
17
GB
GB
Others
Optional accessories
One-touch Remote Control: RMF-ED003
Touchpad Remote Control: RMF-ED004
Camera and Microphone Unit: CMU-BR200/
CMU-BR100
Wireless Subwoofer: SWF-BR100
MHL Cable: DLC-MB10/DLC-MB20/DLC-MC10/
DLC-MC20
Active 3D Glasses: TDG-BT500A (KDL-50W800B
only)
Passive 3D Glasses: TDG-500P (KDL-42W800B
only)
Operating temperature
0 ºC – 40 ºC
Operating humidity
10 % – 80 % RH (non-condensing)
Power and others
Power requirements
19.5 V DC with AC adapter
Rating: Input 220 V - 240 V AC, 50 Hz
Screen size (measured diagonally) (Approx.)
KDL-50W800B: 50 inches / 125.7 cm
KDL-50W700B: 50 inches / 125.7 cm
KDL-42W800B: 42 inches / 106.7 cm
KDL-42W700B: 42 inches / 106.7 cm
KDL-32W700B: 32 inches / 80.1 cm
Display resolution
1,920 dots (horizontal) × 1,080 lines (vertical)
Power consumption
KDL-50W800B: 89 W
KDL-50W700B: 89 W
KDL-42W800B: 88 W
KDL-42W700B: 88 W
KDL-32W700B: 69 W
Dimensions (Approx.) (w × h × d)
with Table-Top Stand
KDL-50W800B: 1,116 × 693 × 179 mm
KDL-50W700B: 1,116 × 693 × 179 mm
KDL-42W800B: 958 × 600 × 170 mm
KDL-42W700B: 958 × 600 × 170 mm
KDL-32W700B: 729 × 465 × 141 mm
without Table-Top Stand
KDL-50W800B: 1,116 × 656 × 64 mm
KDL-50W700B: 1,116 × 656 × 64 mm
KDL-42W800B: 958 × 563 × 64 mm
KDL-42W700B: 958 × 563 × 64 mm
KDL-32W700B: 729 × 433 × 64 mm
Mass (Approx.)
with Table-Top Stand
KDL-50W800B: 14.8 kg
KDL-50W700B: 14.8 kg
KDL-42W800B: 11.7 kg
KDL-42W700B: 11.7 kg
KDL-32W700B: 7.9 kg
without Table-Top Stand
KDL-50W800B: 13.6 kg
KDL-50W700B: 13.6 kg
KDL-42W800B: 10.5 kg
KDL-42W700B: 10.5 kg
KDL-32W700B: 6.9 kg
Note
• Optional accessories availability depends on
countries/region/TV model/stock.
• Design and specifications are subject to change
without notice.
•This TV set incorporates MHL 2.
Trademark information
• The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo
are trademarks or registered trademarks of
HDMI Licensing LLC in the United States
and other countries.
• DLNA®, the DLNA Logo and DLNA
CERTIFIED® are trademarks, service marks,
or certification marks of the Digital Living
Network Alliance.
• Manufactured under license from Dolby
Laboratories.
Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
• “BRAVIA” and are trademarks of
Sony Corporation.
• TrackID is a trademark or registered
trademark of Sony Mobile Communications
AB.
• Gracenote, Gracenote eyeQ, Gracenote
VideoID, Gracenote Video Explore,
Gracenote MusicID, the Gracenote logo
and logotype, and the “Powered by
Gracenote” logo are either registered
trademarks or trademarks of Gracenote in
the United States and/or other countries.
18
GB
• Opera® Devices SDK from Opera Software
ASA. Copyright 1995-2014 Opera Software
ASA. All rights reserved.
• Wi-Fi, Wi-Fi Direct and Miracast are
trademarks or registered trademarks of
Wi-Fi Alliance.
• “Sony Entertainment Network logo” and
“Sony Entertainment Network” are
trademarks of Sony Corporation.
• MHL, Mobile High-Definition Link and the
MHL Logo are trademarks or registered
trademarks of MHL Licensing, LLC.
• For DTS patents, see
http://patents.dts.com. Manufactured
under license from DTS Licensing Limited.
DTS, the Symbol, & DTS and the Symbol
together are registered trademarks, and
DTS Digital Surround is a trademark of DTS,
Inc. © DTS, Inc. All Rights Reserved.
•Designed with UEI Technology
TM
Under License from Universal Electronics
Inc. Portions © UEI 2000 – 2013
• The Bluetooth® word mark and logos are
owned by the Bluetooth SIG, Inc. and any
use of such marks by Sony Corporation is
under license. Other trademarks and trade
names are those of their respective
owners.
• 2014 RealNetworks, Inc. Patents Pending.
All rights reserved. RealNetworks logo is a
trademark of RealNetworks, Inc.
2
CT
目錄
安全資訊 . . . . . . . . . . . . . . . . 2
預先注意事項 . . . . . . . . . . . . . . 4
連接其他設備 . . . . . . . . . . . . . 6
將電視機安裝在牆上 . . . . . . . . . . 7
將支架安裝在牆上 . . . . . . . . . . . . 8
準備安裝電視機 . . . . . . . . . . . . 11
將電視機安裝在牆上 . . . . . . . . . . 12
故障排除 . . . . . . . . . . . . . . 14
故障及解決方案 . . . . . . . . . . . . 14
規格 . . . . . . . . . . . . . . . . 15
簡介
感謝您購買這項 Sony 產品。
使用電視機之前，請詳閱本手冊，並保留下來以便將來參考。
註
• 使用電視機之前，請詳讀 “ 安全資訊 ”( 第 2 頁 )。
• 有關“ 將電視機安裝在牆上” 的指令已包含在這台電視機的說明手
冊。
• 快速設定指南和本說明書中使用的影像和插圖僅作參考並可能與實
際產品的外觀不同。
識別標籤的位置
電視機型號和電源等級的標籤位於電視機背面。
AC 電源供應器型號和序號的標籤位於 AC 電源供應器的底部。
警告
不可將電池曝露於如陽光、火或類似的過熱源。
安裝 / 設定
為了避免火災、觸電或損壞及 / 或受傷等危險，請遵照下列指示來安
裝和使用電視機。
安裝
• 應將電視機安裝在易於插拔的 AC 電源插座附近。
• 將電視機擺在平穩的水平表面上，以防止傾倒而造成人員的傷害或
者損及電視機。
• 僅可由合格的維修人員執行掛壁安裝。
• 為了安全起見，強烈建議您使用 Sony 配件，包括：
壁掛式支架
• 將掛鉤 ( 底座 ) 安裝於電視機上時，務必要使用隨附於壁掛式支架的
螺絲。隨附螺絲如插圖所示設計從掛鉤 ( 底座 ) 安裝表面量起。
螺絲的直徑和長度會因為壁掛式支架的型號而有所不同。
使用隨附螺絲以外的螺絲可能會造成電視機內部損壞或者掉落等
等。
搬動
• 搬動電視機之前，請斷開所有訊號線的連接。
• 大尺寸電視機需要兩到三人搬動。
• 用手搬動電視機時，請如下圖所示抓握。請勿對液晶面板以及螢幕
周圍的框邊施加壓力。
• 搬動電視機時，請勿使其受到搖晃或過度震動。
• 搬動電視機以進行維修或移動時，請使用原有的紙箱和包裝材料進
行包裝。
防止傾倒
• 安裝機器螺絲之前，將顯示幕朝下放置在比電視機大的平穩工作表
面上。
• 務必放一塊軟布在工作表面上以避免損壞液晶顯示的表面。
通風
• 切勿遮擋通風孔或將任何物體插入機殼內。
• 如下圖所示，在電視機周圍保留通風空間。
• 強烈建議您使用 Sony 壁掛式支架以確保足夠的空氣流通。
本電視設計在香港使用，只保證能在香港使用。
安全資訊
螺絲 （隨附於壁掛式支架）
掛鉤 ( 底座 )
電視背後的掛鉤附件
7 毫米
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
他の言語で
- English: Sony KDL-50W800B Reference guide