KDL-48W600B / 40W600B
Television
Reference Guide
GB
CT
2
GB
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Connecting Other Devices. . . . . . . . . . . . . 5
Installing the TV to the Wall . . . . . . . . . . . 6
Troubleshooting . . . . . . . . . . . . . . . . . . . . 10
Troubles and Solutions . . . . . . . . . . . . . . . . 10
Specifications . . . . . . . . . . . . . . . . . . . . . . .11
Introduction
Thank you for choosing this Sony product.
Before operating the TV, please read this manual thoroughly and
retain it for future reference.
Note
• Before operating the TV, please read “Safety Information”
(page 2).
• Instructions about “Installing the TV to the Wall” are included
within this TV’s instructions manual.
• Images and illustrations used in Quick Start Guide and this
manual are for reference only and may differ from actual
product appearance.
Location of the identification label
Labels for the TV Model No., Power Supply rating (in accordance
with applicable safety regulation) and Manufacturing date are
located on the rear of the TV.
Labels for the AC adapter Model No. and Serial No. are located at
the bottom of the AC adapter.
WARNING
Batteries must not be exposed to excessive heat such as
sunshine, fire or the like.
Installation/Set-up
Install and use the TV set in accordance with the instructions
below in order to avoid any risk of fire, electrical shock or damage
and/or injuries.
Installation
• The TV set should be installed near an easily accessible AC
power outlet (mains socket).
• Place the TV set on a stable, level surface to avoid it from falling
down and cause personal injury or damage to the TV.
• Only qualified service personnel should carry out wall
installations.
• For safety reasons, it is strongly recommended that you use
Sony accessories, including:
Wall-Mount Bracket
SU-WL450
• Be sure to use the screws supplied with the Wall-Mount Bracket
when attaching the Mounting Hooks to the TV set. The supplied
screws are designed as indicated by illustration when measured
from the attaching surface of the Mounting Hook.
The diameter and length of the screws differ depending on the
Wall-Mount Bracket model.
Use of screws other than those supplied may result in internal
damage to the TV set or cause it to fall, etc.
This television is designed for use in Hong Kong and ensured
the usage in Hong Kong only.
Safety Information
Screw (supplied with the
Wall-Mount Bracket)
Mounting Hook
Hook attachment on rear
of TV set
8 mm - 10 mm
3
GB
GB
Transporting
• Before transporting the TV set, disconnect all cables.
• Two or three people are needed to transport a large TV set.
• When transporting the TV set by hand, hold it as shown below.
Do not put stress on the LCD panel and the frame around the
screen.
• When transporting the TV set, do not subject it to jolts or
excessive vibration.
• When transporting the TV set for repairs or when moving, pack
it using the original carton and packing material.
Ventilation
• Never cover the ventilation holes or insert anything in the
cabinet.
• Leave space around the TV set as shown below.
• It is strongly recommended that you use a Sony Wall-Mount
Bracket in order to provide adequate air-circulation.
Installed on the wall
Installed with stand
• To ensure proper ventilation and prevent the collection of dirt or
dust:
Do not lay the TV set flat, install upside down, backwards, or
sideways.
Do not place the TV set on a shelf, rug, bed or in a closet.
Do not cover the TV set with a cloth, such as curtains, or items
such as newspapers, etc.
Do not install the TV set as shown below.
AC power cord (mains lead)
Handle the AC power cord (mains lead) and outlet (mains socket)
as follows in order to avoid any risk of fire, electrical shock or
damage and/or injuries:
Use only Sony supplied AC power cords (mains lead), not those
of other brands.
Insert the plug fully into the AC power outlet (mains socket).
Operate the TV set on a 220–240 V AC supply only.
When wiring cables, be sure to unplug the AC power cord
(mains lead) for your safety and take care not to catch your feet
on the cables.
Disconnect the AC power cord (mains lead) from the AC power
outlet (mains socket) before working on or moving the TV set.
Keep the AC power cord (mains lead) away from heat sources.
Unplug the AC power plug (mains plug) and clean it regularly. If
the plug is covered with dust and it picks up moisture, its
insulation may deteriorate, which could result in a fire.
Note
• Do not use the supplied AC power cord (mains lead) on any
other equipment.
• Do not pinch, bend, or twist the AC power cord (mains lead)
excessively. The core conductors may be exposed or broken.
• Do not modify the AC power cord (mains lead).
• Do not put anything heavy on the AC power cord (mains lead).
• Do not pull on the AC power cord (mains lead) itself when
disconnecting the AC power cord (mains lead).
• Do not connect too many appliances to the same AC power
outlet (mains socket).
• Do not use a poor fitting AC power outlet (mains socket).
NOTE ON AC ADAPTER
Warning
To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
To prevent fire or shock hazard, do not place objects filled with
liquids, such as vases, on the apparatus.
Do not install this equipment in a confined space, such as a
bookshelf or similar unit.
• Please ensure that the AC power outlet (mains socket) is
installed near the equipment and shall be easily accessible.
• Be sure to use the supplied AC adapter and AC power cord
(mains lead). Otherwise it may cause a malfunction.
• Connect the AC adapter to an easily accessible AC power outlet
(mains socket).
• Do not coil the AC power cord (mains lead)
around the AC adapter. The core wire may
be cut and/or it may cause a malfunction
of the TV.
• Do not touch the AC adapter with wet hands.
• If you notice an abnormality in the AC adapter, disconnect it
from the AC power outlet (mains socket) immediately.
• The set is not disconnected from the AC source as long as it is
connected to the AC power outlet (mains socket), even if the set
itself has been turned off.
• As the AC adapter will become warm when it is used for a long
time, you may feel hot when touching it by hand.
Prohibited Usage
Do not install/use the TV set in locations, environments or
situations such as those listed below, or the TV set may
malfunction and cause a fire, electrical shock, damage and/or
injuries.
Location:
• Outdoors (in direct sunlight), at the seashore, on a ship or other
vessel, inside a vehicle, in medical institutions, unstable
locations, near water, rain, moisture or smoke.
• If the TV is placed in the changing room of
a public bath or hot spring, the TV may be
damaged by airborne sulphur, etc.
• For best picture quality, do not expose the screen to direct
illumination or sunlight.
• Avoid moving the TV from a cold area to a warm area. Sudden
room temperature changes may cause moisture condensation.
This may cause the TV to show poor picture and/or poor colour.
Should this occur, allow moisture to evaporate completely
before powering the TV on.
Environment:
• Places that are hot, humid, or excessively dusty; where insects
may enter; where it might be exposed to mechanical vibration,
near flammable objects (candles, etc.). The TV set shall not be
exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the TV.
30 cm
10 cm
10 cm
10 cm
Leave at least this space around the set.
30 cm
10 cm
10 cm
Leave at least this space around the set.
6 cm
Air circulation is blocked.
Wall Wall
4
GB
• Do not place the TV in a humid or dusty
space, or in a room with oily smoke or
steam (near cooking tables or
humidifiers). Fire, electric shock, or
warping may result.
• Do not install the TV in places subject to extreme temperature,
such as in direct sunlight, near a radiator or a heating vent. The
TV may overheat in such conditions which can cause
deformation of the enclosure and/or TV malfunction.
Situation:
• Do not use when your hands are wet, with the cabinet removed,
or with attachments not recommended by the manufacturer.
Disconnect the TV set from AC power outlet (mains socket) and
antenna during lightning storms.
• Do not install the TV so that it sticks out
into an open space. Injury or damage
from a person or object bumping into
the TV may result.
Broken pieces:
• Do not throw anything at the TV set. The screen glass may break
by the impact and cause serious injury.
• If the surface of the TV set cracks, do not touch it until you have
unplugged the AC power cord (mains lead). Otherwise electric
shock may result.
When not in use
• If you will not be using the TV set for several days, the TV set
should be disconnected from the AC power (mains) for
environmental and safety reasons.
• As the TV set is not disconnected from the AC power (mains)
when the TV set is just turned off, pull the plug from the AC
power outlet (mains socket) to disconnect the TV set
completely.
• However, some TV sets may have features that require the TV
set to be left in standby to work correctly.
For children
• Do not allow children to climb on the TV set.
• Keep small accessories out of the reach of children, so that they
are not mistakenly swallowed.
If the following problems occur...
Turn off the TV set and unplug the AC power cord (mains lead)
immediately if any of the following problems occur.
Ask your dealer or Sony service centre to have it checked by
qualified service personnel.
When:
AC power cord (mains lead) is damaged.
Poor fitting of AC power outlet (mains socket).
TV set is damaged by being dropped, hit or having something
thrown at it.
Any liquid or solid object falls through openings in the cabinet.
About LCD Monitor Temperature
When the LCD Monitor is used for an extended period, the panel
surrounds become warm. You may feel hot when touching there
by the hand.
Viewing the TV
• View the TV in moderate light, as viewing the TV in poor light or
during long period of time, strains your eyes.
• When using headphones, adjust the volume so as to avoid
excessive levels, as hearing damage may result.
LCD Screen
• Although the LCD screen is made with high-precision
technology and 99.99% or more of the pixels are effective, black
dots may appear or bright points of light (red, blue, or green)
may appear constantly on the LCD screen. This is a structural
property of the LCD screen and is not a malfunction.
• Do not push or scratch the front filter, or place objects on top of
this TV set. The image may be uneven or the LCD screen may be
damaged.
• If this TV set is used in a cold place, a smear may occur in the
picture or the picture may become dark. This does not indicate a
failure. These phenomena disappear as the temperature rises.
• Ghosting may occur when still pictures are displayed
continuously. It may disappear after a few moments.
• The screen and cabinet get warm when this TV set is in use. This
is not a malfunction.
• The LCD screen contains a small amount of liquid crystal. Follow
your local ordinances and regulations for disposal.
Handling and cleaning the screen surface/
cabinet of the TV set
Be sure to unplug the AC power cord (mains lead) connected to
the TV set from AC power outlet (mains socket) before cleaning.
To avoid material degradation or screen coating degradation,
observe the following precautions.
• To remove dust from the screen surface/cabinet, wipe gently
with a soft cloth. If dust is persistent, wipe with a soft cloth
slightly moistened with a diluted mild detergent solution.
• Never spray water or detergent directly on
the TV set. It may drip to the bottom of the
screen or exterior parts and enter the TV set,
and may cause damage to the TV set.
• Never use any type of abrasive pad, alkaline/acid cleaner,
scouring powder, or volatile solvent, such as alcohol, benzene,
thinner or insecticide. Using such materials or maintaining
prolonged contact with rubber or vinyl materials may result in
damage to the screen surface and cabinet material.
• Periodic vacuuming of the ventilation openings is
recommended to ensure to proper ventilation.
• When adjusting the angle of the TV set, move it slowly so as to
prevent the TV set from moving or slipping off from its table
stand.
Optional Equipment
Keep optional components or any equipment emitting
electromagnetic radiation away from the TV set. Otherwise
picture distortion and/or noisy sound may occur.
Wireless Function of the unit
• Do not operate this unit near medical equipment (pacemaker,
etc.), as malfunction of the medical equipment may result.
• Although this unit transmits/receives scrambled signals, be
careful of unauthorised interception. We cannot be responsible
for any trouble as a result.
Caution about handling the remote control
• Observe the correct polarity when inserting batteries.
• Do not use different types of batteries together or mix old and
new batteries.
• Dispose of batteries in an environmentally friendly way. Certain
regions may regulate the disposal of batteries. Please consult
your local authority.
• Handle the remote control with care. Do not drop or step on it,
or spill liquid of any kind onto it.
• Do not place the remote control in a location near a heat source,
a place subject to direct sunlight, or a damp room.
Precautions
5
GB
GB
Connecting Other Devices
To connect with an HDMI cable
To connect with component cables
To connect with AV composite cables
To HDMI OUT
< 21 mm
< 12 mm
To AUDIO OUT To COMPONENT
OUT (P
R/PB/Y)
To VIDEO OUT
SD HD
Picture Quality
• AV composite cable
• Antenna (aerial) cable
Standard definition (SD) videos have picture signals with a
vertical resolution of 480 (NTSC) or 576 (PAL/SECAM) lines.
• Component cable • HDMI cable
High definition (HD) videos have picture signals
with a vertical resolution of 720 or 1080 lines.
6
GB
Installing the TV to the Wall
This TV’s instruction manual only shows the steps on preparing the installation of the TV before
installing to the wall.
To Customers:
For product protection and safety reasons, Sony strongly recommends that installation of your
TV be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.
To Sony Dealers and Contractors:
Provide full attention to safety during the installation, periodic maintenance and examination of
this product.
Use the Wall-Mount Bracket SU-WL450 (not supplied) to install the TV to the wall. When
installing the Wall-Mount Bracket, also refer to the Operating Instructions and Installation Guide
supplied with the Wall-Mount Bracket.
Note
• If the Table-Top Stand is attached to the TV, detach the Table-Top Stand beforehand. See the Quick Start Guide and
follow in reverse order the steps to attach the Table-Top Stand.
• Place the TV with its screen facing down on a level and stable surface covered with a thick and soft cloth, when
securing the Attachment parts for Wall-Mount Bracket or when removing the Table-Top Stand from the TV to prevent
damaging the surface of the LCD display.
• Be sure to store the removed screws in a safe place, keeping them away from children.
Sufficient expertise is required for installing this product, especially to determine the strength of the wall for
withstanding the TV’s weight. Be sure to entrust the attachment of this product to the wall to Sony dealers
or licensed contractors and pay adequate attention to safety during the installation. Sony is not liable for
any damage or injury caused by mishandling or improper installation.
7
GB
GB
1 Make sure that the wall has enough space for the TV and is capable of supporting a
weight of at least four times that of the TV.
Refer to the following table on installing the TV to the wall. See page 11-13 (Specifications)
for the TV’s weight.
Unit: mm
Note
• Figures in the table may differ slightly depending on the installation.
• When your TV is installed on the wall, the upper side of the TV slightly leans forward.
2 Attach the Attachment parts for Wall-Mount Bracket. Check the Attachment parts by
referring to “1” of the Wall-Mount Bracket Installation Guide.
Note
• If using an electric screwdriver, set the torque at approximately 1.5 N·m {15 kgf·cm}.
• Be sure to store the unused parts in a safe place for future use. Retain this manual for future reference.
Standard mounting
Model Name
KDL-
Display dimensions
Screen
centre
dimension
Length for mounting
Standard
mounting
Slim
mounting
48W600B 1,086 646 29 305 152 111
40W600B 926 556 16 306 151 110
Screen centre point
80
Standard mounting Slim mounting
Screw (+PSW 6 x 20)
Pulley
Screw (+PSW 6 x 50)
Belt
Soft cloth
Spacer (60 mm)
8
GB
Slim mounting
Note
• You cannot use some of the terminals on the rear of the TV when using this mounting style.
3 Connect necessary cables to the TV.
Note
• You cannot access to any terminal after installing the TV to the wall.
4 Bundle the AC Adapter using the cable holders G (supplied with the TV). Make sure that
the label is facing outwards when bundling AC adapter.
Screw (+PSW 6 x 20)
Pulley
Screw (+PSW 6 x 20)
Belt
Soft cloth
Spacer (20 mm)
123
9
GB
GB
5 Install the TV to the Base. Refer to “5” of Installation Guide and “Installing the TV to the
Wall” of Operating Instructions supplied with the Wall-Mount Bracket.
Refer to the instructions supplied with the Wall-Mount Bracket for your model to install the TV on the wall.
Model Name KDL- Hook location
48W600B
c
40W600B
a
b
c
d
10
GB
Troubleshooting
When the LED indicator is flashing red, count
how many times it flashes (interval time is
three seconds).
If the LED indicator flashes red, reset the TV by
disconnecting the AC power cord (mains lead)
from the TV for two minutes, then turn on the
TV.
If the problem persists, contact your dealer or
Sony service centre with the number of times
the LED indicator flashes red (interval time is
three seconds). Press / on the TV to turn it
off, disconnect the AC power cord (mains lead),
and inform your dealer or Sony service centre.
When the LED indicator is not flashing, check
the items as follows.
You can also refer to [Troubleshooting] in the
i-Manual or perform self-diagnosis by selecting
[Help] [Customer Support] [Self
Diagnostics]. If the problem persists, have your
TV serviced by qualified service personnel.
Troubles and Solutions
There is no picture (screen is dark) and no
sound.
Check the antenna (aerial)/cable connection.
Connect the TV to the AC power (mains), and
press / on the TV or remote control.
Some programmes cannot be tuned.
Check the antenna (aerial).
The remote control does not function.
Replace the batteries.
Your TV may be in SYNC mode.
Press SYNC MENU, select [TV Control] and then
select [Home (Menu)] or [Options] to control the
TV.
The [Parental Lock] password has been
forgotten.
Enter 9999 for the PIN code. (PIN code 9999 is
always accepted.)
The TV surrounds become warm.
When the TV is used for an extended period, the
TV surrounds become warm.
You may feel hot when touching there by the
hand.
Frozen audio or video, a blank screen, or the
TV does not respond to TV or remote control
buttons.
Perform a simple reset of the TV by unplugging
the AC power cord (mains lead) for two minutes,
then plug it in again.
The /, CH+/–, +/–, ///, , and
HOME buttons cannot be located on the TV.
See below illustration for location of the buttons
on the TV.
Cannot connect to a wireless router by WPS.
If you use WEP security, select [Easy] t [Wi-Fi] t
[Connect by scan list]. Then, select the network
name (SSID) you want to connect.
Cannot find the required network name in
network setup.
Select [[Manual Entry]] and press to enter
network name.
Rear of TV
11
GB
GB
Specifications
System
Panel system
LCD (Liquid Crystal Display) Panel, LED backlight
TV system
Analogue: B/G, I, D/K, M, L
Digital: DTMB
Colour/video system
Analogue: PAL, SECAM, NTSC3.58, NTSC4.43
Digital: Refer to the i-Manual
Channel coverage
Analogue: UHF/VHF/Cable
Digital: UHF
Sound output
8 W + 8 W
Wireless technology
Protocol IEEE802.11a/b/g/n
Input/Output jacks
Antenna (aerial)/cable
75 ohm external terminal for VHF/UHF
/ VIDEO IN 1
Video/Audio input (phono jacks)
/ COMPONENT IN
YPBPR (Component Video): 1080p (50, 60 Hz),
1080i (50, 60 Hz), 720p (50, 60 Hz), 576p, 576i,
480p, 480i
Audio input (phono jacks)
VIDEO IN 2
Video input (common phono pin with Y input)
HDMI IN 1, 2, 3, 4
Video: 1080p (30, 50, 60 Hz), 1080/24p,
1080i (50, 60 Hz), 720p (30, 50, 60 Hz),
720/24p, 576p, 576i, 480p, 480i, PC Formats
Audio: 5.1 channel linear PCM: 32, 44.1 and
48 kHz, 16, 20 and 24 bits, Dolby Digital
ARC (Audio Return Channel) (HDMI IN 2 only)
MHL (common with HDMI IN 1)
Video: 1080p (30 Hz), 1080/24p, 1080i (50, 60 Hz),
720p (30, 50, 60 Hz), 720/24p, 576p, 576i, 480p,
480i
Audio: 5.1 channel linear PCM: 32, 44.1 and
48 kHz, 16, 20 and 24 bits, Dolby Digital
DIGITAL AUDIO OUT (OPTICAL)
Digital optical jack (Two channel linear PCM,
Dolby Digital)
HDMI 3 AUDIO IN
Analogue audio input (stereo mini jack)
AUDIO OUT/
Audio output (stereo mini jack)
Headphone jack
(supports Subwoofer out)
1, 2
USB port
DC IN 19.5 V
AC adapter input
LAN
10BASE-T/100BASE-TX connector (Depending on
the operating environment of the network,
connection speed may differ. 10BASE-T/100BASE-
TX communication rate and communication
quality are not guaranteed for this TV.)
Others
Optional accessories
Wall-Mount Bracket: SU-WL450
Camera and Microphone Unit: CMU-BR200/
CMU-BR100
Wireless subwoofer: SWF-BR100
MHL cable: DLC-MB10/DLC-MB20/DLC-MC10/
DLC-MC20
Operating temperature
0 ºC – 40 ºC
Operating humidity
10 % – 80 % RH (non-condensing)
Power and others
Power requirements
19.5 V DC with AC adapter
Rating: Input 220 V - 240 V AC, 50 Hz
Screen size (measured diagonally) (Approx.)
KDL-48W600B: 48 inches / 120.9 cm
KDL-40W600B: 40 inches / 101.6 cm
Display resolution
1,920 dots (horizontal) × 1,080 lines (vertical)
Power consumption
KDL-48W600B: 75 W
KDL-40W600B: 75 W
Dimensions (Approx.) (w × h × d)
with Table-Top Stand
KDL-48W600B: 1,086 × 675 × 181 mm
KDL-40W600B: 926 × 584 × 162 mm
without Table-Top Stand
KDL-48W600B: 1,086 × 646 × 90 mm
KDL-40W600B: 926 × 556 × 89 mm
12
GB
Mass (Approx.)
with Table-Top Stand
KDL-48W600B: 10.3 kg
KDL-40W600B: 7.9 kg
without Table-Top Stand
KDL-48W600B: 9.9 kg
KDL-40W600B: 7.4 kg
Note
• Optional accessories availability depends on
countries/region/TV model/stock.
• Design and specifications are subject to change
without notice.
• This TV set incorporates MHL 2.
Trademark information
• The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo
are trademarks or registered trademarks of
HDMI Licensing LLC in the United States
and other countries.
• DLNA®, the DLNA Logo and DLNA
CERTIFIED® are trademarks, service marks,
or certification marks of the Digital Living
Network Alliance.
• Manufactured under license from Dolby
Laboratories.
Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
• “BRAVIA” and are trademarks of
Sony Corporation.
• TrackID is a trademark or registered
trademark of Sony Mobile Communications
AB.
• Gracenote, Gracenote eyeQ, Gracenote
VideoID, Gracenote Video Explore,
Gracenote MusicID, the Gracenote logo
and logotype, and the “Powered by
Gracenote” logo are either registered
trademarks or trademarks of Gracenote in
the United States and/or other countries.
• Opera® Devices SDK from Opera Software
ASA. Copyright 1995-2014 Opera Software
ASA. All rights reserved.
• Wi-Fi, Wi-Fi Direct and Miracast are
trademarks or registered trademarks of
Wi-Fi Alliance.
• “Sony Entertainment Network logo” and
“Sony Entertainment Network” are
trademarks of Sony Corporation.
• MHL, Mobile High-Definition Link and the
MHL Logo are trademarks or registered
trademarks of MHL Licensing, LLC.
• For DTS patents, see
http://patents.dts.com. Manufactured
under license from DTS Licensing Limited.
DTS, the Symbol, & DTS and the Symbol
together are registered trademarks, and
DTS Digital Surround is a trademark of DTS,
Inc. © DTS, Inc. All Rights Reserved.
• Designed with UEI Technology
TM
Under License from Universal Electronics
Inc. Portions © UEI 2000 – 2013
• 2014 RealNetworks, Inc. Patents Pending.
All rights reserved. RealNetworks logo is a
trademark of RealNetworks, Inc.
13
GB
GB
2
CT
目錄
安全資訊 . . . . . . . . . . . . . . . . 2
預先注意事項 . . . . . . . . . . . . . . 4
連接其他設備 . . . . . . . . . . . . . 5
將電視機安裝在牆上 . . . . . . . . . . 6
故障排除 . . . . . . . . . . . . . . 10
故障及解決方案 . . . . . . . . . . . . 10
規格 . . . . . . . . . . . . . . . . 11
簡介
感謝您購買這項 Sony 產品。
使用電視機之前，請詳閱本手冊，並保留下來以便將來參考。
註
• 使用電視機之前，請詳讀 “ 安全資訊 ”( 第 2 頁 )。
• 有關“將電視機安裝在牆上”的指令已包含在這台電視機的說明手
冊。
• 快速設定指南和本說明書中使用的影像和插圖僅作參考並可能與實
際產品的外觀不同。
識別標籤的位置
電視機型號、電源等級的標籤 （根據適用的安全規定）以及製造日
期位於電視機背面。
警告
不可將電池曝露於如陽光、火或類似的過熱源。
安裝 / 設定
為了避免火災、觸電或損壞及 / 或受傷等危險，請遵照下列指示來安
裝和使用電視機。
安裝
• 應將電視機安裝在易於插拔的 AC 電源插座附近。
• 將電視機擺在平穩的水平表面上，以防止傾倒而造成人員的傷害或
者損及電視機。
• 僅可由合格的維修人員執行掛壁安裝。
• 為了安全起見，強烈建議您使用 Sony 配件，包括：
壁掛式支架
SU-WL450
• 將掛牆式支架安裝於電視機上時，務必要使用隨附於壁掛式支架的
螺絲。隨附螺絲如插圖所示設計從壁掛式支架安裝表面量起。
螺絲的直徑和長度會因為壁掛式支架的型號而有所不同。
使用隨附螺絲以外的螺絲可能會造成電視機內部損壞或者掉落等
等。
搬動
• 搬動電視機之前，請斷開所有訊號線的連接。
• 大尺寸電視機需要兩到三人搬動。
• 用手搬動電視機時，請如下圖所示抓握。請勿對液晶面板以及螢幕
周圍的框邊施加壓力。
• 搬動電視機時，請勿使其受到搖晃或過度震動。
• 搬動電視機以進行維修或移動時，請使用原有的紙箱和包裝材料進
行包裝。
通風
• 切勿遮擋通風孔或將任何物體插入機殼內。
• 如下圖所示，在電視機周圍保留通風空間。
• 強烈建議您使用 Sony 壁掛式支架以確保足夠的空氣流通。
本電視設計在香港使用，只保證能在香港使用。
安全資訊
螺絲 （隨附於壁掛式支架）
掛鉤
8 毫米 - 10 毫米
電視背後的掛鉤附件
3
CT
GB
CT
安裝在牆壁上
安裝在底座上
• 為了確保正確通風及防止髒物或灰塵堆積：
請勿將電視機平放、上面朝下安裝、向後安裝或側面安裝。
請勿將電視機放置於架子、地毯、床或壁櫥中。
請勿用布 （如窗簾）或物件 （如報紙等）覆蓋電視機。
請勿如下圖所示安裝電視機。
AC 電源線
為了避免火災、觸電或損壞及 / 或受傷等危險，請遵照下列指示來處
理 AC 電源線和插座 :
請僅使用 Sony 隨附的 AC 電源線，不要使用其它品牌的電源線。
將插頭完全插入 AC 電源插座。
僅可在 220-240 V AC 電源上使用電視機。
連接訊號線時，為了安全起見請務必拔下 AC 電源線，以免被訊號線
絆到腳。
在進行作業或移動電視機之前，請從AC電源插座上斷開AC電源線的
連接。
保持 AC 電源線遠離熱源。
拔下 AC 電源插頭，定期進行清潔。如果插頭上有積灰並帶有濕氣，
則其絕緣品質可能已經劣化，並可能會造成火災。
註
• 請勿在任何其它設備上使用所隨附的 AC 電源線。
• 請勿過度擰捏、彎曲或扭轉 AC 電源線。否則線芯可能會曝露在外或
折斷。
• 請勿改裝 AC 電源線。
• 請勿將任何重物放在 AC 電源線上。
• 斷開 AC 電源線連接時，請勿拉扯 AC 電源線。
• 請勿在相同的 AC 電源插座上連接太多設備。
• 請勿使用不適當的 AC 電源插座。
AC 電源供應器的注意事項
警告
為了減低火災或觸電的風險，請勿讓本裝置暴露於雨水或濕氣中。
為了避免火災或觸電的危險，請勿將盛裝液體的物體，例如花瓶放在
裝置上。
請勿將本設備安裝在狹窄封閉的空間，例如書架或類似裝置。
• 請確保將 AC 電源插座安裝在設備附近並易於插拔。
• 請務必使用隨附的 AC 電源供應器和 AC 電源線。否則這可能導致故
障。
• 將 AC 電源供應器連接至易於插拔的 AC 電源插座。
• 請勿將 AC 電源線盤繞在 AC 電源供應器上。
芯線可能折斷並 （或）導致電視機故障。
• 手濕時請勿觸碰 AC 電源供應器。
• 如果您發現 AC電源供應器異常，立刻將AC電源供應器從AC 電源插座
拔下。
• 只要本機仍然連接至 AC 電源插座，即使本機已經關閉，AC 電源還是
未切斷。
• 由於 AC 電源供應器在長時間使用後會發熱，用手觸摸時可能會感到
熱。
使用限制
請勿在下列地點、環境或情況條件下安裝 / 使用電視機，否則電視機
可能會發生故障並造成火災、觸電、損壞及 / 或受傷等危險。
地點：
• 室外 （在直射的陽光中），海邊，船上或其他船艦上，車內，醫療
機構中，不穩定的場所，靠近水、雨、濕氣或煙霧的地方。
• 如果放置電視機在公共浴室或溫泉的更衣室
內，電視機可能會被空降硫磺等損壞。
• 若要獲得最佳的畫面品質，請勿將螢幕放在直射光源或陽光下。
• 避免將電視機從寒冷的區域移至溫熱的區域。突然的室溫變化可能
導致濕氣凝結。這可能造成電視機顯示劣質圖像及 / 或暗淡的顏
色。如果發生這種情形，讓濕氣完全蒸發之後才開啟電視機。
環境：
• 炎熱、潮濕或太多灰塵的地方；昆蟲可能進入的地方；可能受到機
械式震動的地方；靠近易燃物體 （蠟燭等）的地方。不應該讓液體
滴濕或噴濕電視機，而且裝滿液體的物體 （例如花瓶）不應該擺在
電視機上。
• 不要放置電視機在潮濕或多塵的空間，或
有油煙或蒸氣的場所 （靠近灶台或加濕
器）。這可能導致火災、觸電或本機彎
曲。
• 請勿將電視機安裝在會遭受極端溫度的位置，如陽光直射、靠近散
熱器或加熱裝置通風孔的地方。電視機在這種環境下可能會過熱而
導致外殼變形及 / 或電視機故障。
情況條件：
• 手濕，機殼拆除或採用非製造商所建議的配件時切勿使用本電視
機。出現雷電時請將電視機電源線從 AC 電源插座和天線拔下。
• 不要把電視機安裝在延伸出開放的空間。
這可能導致人或物體碰撞電視機而受傷或
損壞。
打破電視機螢幕：
• 請勿將任何物品丟向電視機。否則螢幕可能會因為受到撞擊而破裂
並造成嚴重傷害。
• 如果電視機的表層破裂，在拔下 AC 電源線以前請勿觸摸它。否則可
能導致觸電。
不使用時
• 如果您不使用電視機數天，為了環保和安全原因，應將電視機電源
線從 AC 電源插座上拔下。
• 關閉電視機電源時，電視機並未與 AC 電源斷開連接，請將插頭從 AC
電源插座上拔下以完全斷開電視機的電源連接。
• 但是，某些電視機可能具有需要將電視機保持在待命模式下才能正
常工作的特點。
對於兒童
• 請勿讓兒童爬上電視機。
• 將體積小的配件放在兒童拿不到的地方，以便不會被兒童誤吞。
30 厘米
10 厘米
10 厘米
10 厘米
在電視機周圍至少留出所示的空間。
30 厘米
10 厘米
10 厘米
在電視機周圍至少留出所示的空間。
6厘米
空氣流通被阻擋。
牆壁 牆壁
4
CT
如果出現下列問題 …
如果出現以下任何問題，請立刻關閉電視機並拔下 AC 電源線。
請諮詢您的經銷商或 Sony 服務中心以交由合格的服務人員進行檢
查。
當：
AC 電源線損壞。
AC 電源插座不適當。
電視機由於跌落、敲擊或撞擊而損壞。
任何液體或固體物件通過開口處掉入機殼內。
關於液晶螢幕溫度
長時間使用液晶螢幕時，面板周圍溫度會升高。
用手觸摸這些地方時可能會覺得很燙。
觀賞電視
• 請在適當光線條件下觀賞電視，因為在光線不足條件下或長時間觀
賞電視會損傷您的眼睛。
• 使用耳機時，請調整音量以免音量過高損傷聽力。
LCD 螢幕
• 雖然 LCD 螢幕採用最精密技術製造且 99.99% 以上的畫素有效，但還
是可能會出現黑點或 LCD 螢幕上可能會經常出現亮點 （紅、藍或綠
色）。這是 LCD 螢幕的結構特性，並不是故障。
• 請勿按壓或刮傷前濾光面板或在電視機頂部放置物件。畫面可能會
不均， 或者 LCD 螢幕可能會損壞。
• 如果在寒冷地點使用本電視機，畫面上可能會出現模糊或變暗。這
並不是故障。溫度上升後這些現象就會消失。
• 畫面靜止不動將會產生重影。片刻後該現象將消失。
• 電視機使用過程中，螢幕和機殼會變熱。這不是故障。
• LCD 螢幕包含少量液晶。請按照您當地的法規進行廢棄物處理。
使用和清潔電視機的螢幕表層 / 機殼
清潔前，務必將電視機的 AC 電源線從 AC 電源插座上斷開連接。
為了避免物質或螢幕塗層剝離，請遵照下列預先注意事項。
• 若要擦去螢幕表層 / 機殼上的灰塵，請用軟布輕輕擦拭。如果灰塵
較難除去，請用稍稍蘸有稀釋中性清潔溶劑的軟布進行擦拭。
• 絕對不能將水或清潔劑直接噴灑在電視上。液
體可能滴落在螢幕的底部或外部零件上並滲入
電視內，而毀壞電視。
• 切勿使用任何類型的磨砂墊、鹼性 / 酸性清潔劑、擦洗粉或揮發溶
劑，如酒精、汽油、稀釋劑或殺蟲劑。使用上述材料或與橡膠或乙
烯材料長時間接觸可能會造成螢幕表層和機殼材料的損壞。
• 建議您定期使用真空吸塵清理通風口以確保通風順暢。
• 當調整電視機的角度時，請慢慢地調動以防電視機從其桌面型底座
移動或滑落。
選購設備
將產生電磁輻射的選購元件或任何其他設備遠離電視機。否則可能會
造成畫面失真及 / 或噪聲。
本機的無線功能
• 請勿在醫療設備 （心臟起搏器等等）附近操作本機，這將導致該醫
療設備故障。
• 雖然本機發送 / 接收加擾信號，請小心未經授權的截取。我們不對
此造成的任何問題負責。
注意有關處理遠程控制
• 安裝電池時請注意正確的極性位置。
• 請勿同時使用不同類型的電池或混合使用新舊電池。
• 請以符合環境保護規定的方式來丟棄電池。特定地區可能有制訂廢
棄電池的相關規定。請向您當地的主管機關查詢。
• 請小心拿取遙控器。請勿讓遙控器掉落或踩在遙控器上，或是讓任
何液體濺到遙控器。
• 請勿將遙控器放置在接近熱源的地方，放置在受日光直射地方或潮
濕的房間。
預先注意事項
5
CT
GB
CT
連接其他設備
以 HDMI 連接線連接
以色差纜線連接
以 AV 複合纜線連接
至 HDMI OUT
< 21 毫米
< 12 毫米
至 AUDIO OUT 至 COMPONENT
OUT (P
R/PB/Y)
至 VIDEO OUT
SD HD
圖像品質
• AV 複合訊號線
• 天線的連接訊號線
標準清晰度 （SD）視訊圖像信號的垂直解析度為 480 （NTSC）
或 576 （PAL/SECAM）條線。
• 色差訊號線 • HDMI 訊號線
高清晰度 （HD）視訊圖像信號的垂直解析度為 720
或 1080 條線。
6
CT
將電視機安裝在牆上
本電視機安裝手冊僅說明將電視機安裝到牆上前的安裝準備步驟。
致客戶 :
基於保護產品和安全考量，Sony 強烈建議務必委由 Sony 經銷商或經授權的承包商進行電視機的安
裝。請勿試圖⾃行安裝。
致 Sony 經銷商和承包商 :
請在安裝、定期維修和檢查本產品時特別注意安全。
使用壁掛式支架 SU-WL450 （非附件），將電視機安裝至牆壁上。 安裝壁掛式支架時，亦請參閱壁掛
式支架隨附的 《操作手冊》及 《安裝指南》。
註
• 如果桌面底座安裝於電視機，預先拆下桌面底座。請參閱快速設定指南，反向操作步驟以安裝桌面底座。
• 當固定壁挂式支架的附件，或從電視機上拆下桌面底座时，請將電視機屏幕面朝下放置在鋪有厚實軟布的穩定水平表面
上，以防損壞 LCD 屏幕表面。
• 請務必將取下的螺絲放置在安全的地方，讓螺絲遠離兒童。
安裝本產品，尤其是在確定牆壁強度是否能夠支撐電視機重量方面，需要足夠的專業知識。將本產品安裝於牆上
的工作務必要委託 Sony 經銷商或經過授權的承包商進行，而且安裝時要特別注意安全。Sony 對於任何因為錯誤
操作或不當安裝所造成的損壞或傷害恕不負責。
7
CT
GB
CT
1 確保牆壁有足夠空間以及能支撐至少電視機四倍的重量。
請參閱以下列表有關在牆上安裝電視機。請參閲第 11-12 頁 （規格）有關電視機的重量。
單元 : 毫米
註
• 製表內的數字視安裝而可能略有不同。
• 當您的電視機安裝在牆上時，電視機的上部稍微向前傾。
2 安裝壁掛式支架的隨附附件。請參閱 “ 壁掛式支架安裝指南 ” 中的步驟 “1” 檢查隨附附件。
註
• 如果使用電動螺絲起子，請將扭矩設定為大約 1.5 N·m {15 kgf·cm}。
• 確保將沒有使用的零件存放在安全的地方以供日後使用。保留本手冊以便將來參考。
標準安裝
型號名稱
KDL-
顯示幕
螢幕中心
尺寸
安裝的長度
標準安裝 薄型安裝
48W600B 1,086 646 29 305 152 111
40W600B 926 556 16 306 151 110
螢幕中心點
80
標準安裝 薄型安裝
螺絲 (+PSW 6 x 20)
滑輪
螺絲 (+PSW 6 x 50)
帶子
軟布
墊片 (60 mm)
8
CT
薄型安裝
註
• 使用此安裝樣式時，無法使用電視機背面的部分端子。
3 將必要纜線連接至電視機。
註
• 將電視機安裝至牆壁後，您將無法接觸任何端子。
4 使用纜線固定器 G （電視機隨附）捆綁 AC 適配器。捆綁 AC 適配器時，確保標籤面朝外。
螺絲 (+PSW 6 x 20)
滑輪
螺絲 (+PSW 6 x 20)
帶子
軟布
墊片 (20 mm)
123
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
他の言語で
- English: Sony KDL-40W600B Reference guide