Sony KD-55X9000C リファレンスガイド

KD-65X9000C / 55X9000C

Television

Reference Guide

GB

CT

2

GB

Table of Contents

Safety Information . . . . . . . . . . . . . . . . . . . . . 2

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Parts and Controls . . . . . . . . . . . . . . . . . . . 6

Controls and Indicators . . . . . . . . . . . . . . . . . 6

Inputs and Outputs . . . . . . . . . . . . . . . . . . . . 7

Using Remote Control . . . . . . . . . . . . . . . . 9

Remote Control Parts Description . . . . . . . . .9

Using the Touchpad Remote Control . . . . . 11

Launching the Touchpad Remote

Control Introduction/Tutorial. . . . . . . . . . . . 11

Attaching the Table-Top Stand

(Alternative) . . . . . . . . . . . . . . . . . . . . . . . .11

Connecting the TV . . . . . . . . . . . . . . . . . . 14

Installing the TV to the Wall . . . . . . . . . . 17

Using the supplied Wall-Mount Bracket . . . 17

Using an optional Wall-Mount Bracket. . . . 23

Troubleshooting . . . . . . . . . . . . . . . . . . . . 27

Troubles and Solutions . . . . . . . . . . . . . . . . 27

Specifications . . . . . . . . . . . . . . . . . . . . . . 28

Introduction

Thank you for choosing this Sony product.

Before operating the TV, please read this manual thoroughly and

retain it for future reference.

Note

• Before operating the TV, please read “Safety Information”

(page 2).

• Instructions about “Installing the TV to the Wall” are included

within this TV’s instructions manual.

• Images and illustrations used in Startup Guide and this manual

are for reference only and may differ from actual product

appearance.

Location of the identification label

Labels for the Model No. and Power Supply rating are located on

the rear of the TV.

WARNING

Batteries must not be exposed to excessive heat such as

sunshine, fire or the like.

Installation/Set-up

Install and use the TV set in accordance with the instructions

below in order to avoid any risk of fire, electrical shock or damage

and/or injuries.

Installation

• The TV set should be installed near an easily accessible AC

power outlet (mains socket).

• Place the TV set on a stable, level surface to avoid it from falling

down and cause personal injury or damage to the TV.

• Install the TV where it cannot be pulled, pushed, or knocked

over.

• Install the TV so that the TV's Table-Top Stand does not

protrudes out from the TV stand (not supplied). If the Table-Top

Stand protrudes out from the TV stand, it may cause TV set to

topple over, fall down, and cause personal injury or damage to

the TV.

• Pay attention so that a child does not approach during the

Table-Top Stand installation.

• Only qualified service personnel should carry out wall

installations.

• For safety reasons, it is strongly recommended that you use

Sony accessories, including:

 Wall-Mount Bracket SU-WL500

This television is designed for use in Hong Kong and ensured

the usage in Hong Kong only.

Safety Information

3

GB

• Be sure to use the screws supplied with the Wall-Mount Bracket

when attaching the Wall-Mount Bracket to the TV set. The

supplied screws are designed as indicated by illustration when

measured from the attaching surface of the Wall-Mount Bracket.

The diameter and length of the screws differ depending on the

Wall-Mount Bracket model.

Use of screws other than those supplied may result in internal

damage to the TV set or cause it to fall, etc.

Refer to page 17 in case of “Using the supplied Wall-Mount

Bracket”.

Refer to page 23 in case of “Using the optional Wall-Mount

Bracket”.

Transporting

• Before transporting the TV set, disconnect all cables.

• Two or three people are needed to transport a large TV set.

• When transporting the TV set by hand, hold it as shown below.

Do not put stress on the LCD panel and the frame around the

screen.

• When transporting the TV set, do not subject it to jolts or

excessive vibration.

• When transporting the TV set for repairs or when moving, pack

it using the original carton and packing material.

Ventilation

• Never cover the ventilation holes or insert anything in the

cabinet.

• Leave space around the TV set as shown below.

• It is strongly recommended that you use a Sony Wall-Mount

Bracket in order to provide adequate air circulation.

Installed on the wall

Installed with stand

• To ensure proper ventilation and prevent the collection of dirt or

dust:

 Do not lay the TV set flat, install upside down, backwards, or

sideways.

 Do not place the TV set on a shelf, rug, bed or in a closet.

 Do not cover the TV set with a cloth, such as curtains, or items

such as newspapers, etc.

 Do not install the TV set as shown below.

 Do not place anything directly below the TV.

AC power cord (mains lead)

Handle the AC power cord (mains lead) and outlet (mains socket)

as follows in order to avoid any risk of fire, electrical shock or

damage and/or injuries:

 Insert the plug fully into the AC power outlet (mains socket).

 Operate the TV set on a 220–240 V AC supply only.

 When wiring cables, be sure to unplug the AC power cord

(mains lead) for your safety and take care not to catch your feet

on the cables.

 Disconnect the AC power cord (mains lead) from the AC power

outlet (mains socket) before working on or moving the TV set.

 Keep the AC power cord (mains lead) away from heat sources.

 Unplug the AC power plug (mains plug) and clean it regularly. If

the plug is covered with dust and it picks up moisture, its

insulation may deteriorate, which could result in a fire.

Note

• Do not use the supplied AC power cord (mains lead) on any

other equipment.

• Do not pinch, bend, or twist the AC power cord (mains lead)

excessively. The core conductors may be exposed or broken.

• Do not modify the AC power cord (mains lead).

• Do not put anything heavy on the AC power cord (mains lead).

• Do not pull on the AC power cord (mains lead) itself when

disconnecting the AC power cord (mains lead).

• Do not connect too many appliances to the same AC power

outlet (mains socket).

• Do not use a poor fitting AC power outlet (mains socket).

Prohibited Usage

Do not install/use the TV set in locations, environments or

situations such as those listed below, or the TV set may

malfunction and cause a fire, electrical shock, damage and/or

injuries.

Location:

• Outdoors (in direct sunlight), at the seashore, on a ship or other

vessel, inside a vehicle, in medical institutions, unstable

locations, near water, rain, moisture or smoke.

• If the TV is placed in the changing room of

a public bath or hot spring, the TV may be

damaged by airborne sulfur, etc.

• For best picture quality, do not expose the screen to direct

illumination or sunlight.

• Avoid moving the TV from a cold area to a warm area. Sudden

room temperature changes may cause moisture condensation.

This may cause the TV to show poor picture and/or poor colour.

Should this occur, allow moisture to evaporate completely

before powering the TV on.

30 cm

10 cm

Do not place anything directly below the TV.

30 cm

10 cm

Do not place anything directly below the TV.

6 cm

Air circulation is blocked.

Wall Wall

4

GB

Environment:

• Places that are hot, humid, or excessively dusty; where insects

may enter; where it might be exposed to mechanical vibration,

near flammable objects (candles, etc). The TV set shall not be

exposed to dripping or splashing and no objects filled with

liquids, such as vases, shall be placed on the TV.

• Do not place the TV in a humid or dusty

space, or in a room with oily smoke or

steam (near cooking tables or

humidifiers). Fire, electric shock, or

warping may result.

• Do not install the TV in places subject to extreme temperature,

such as in direct sunlight, near a radiator or a heating vent. The

TV may overheat in such conditions which can cause

deformation of the enclosure and/or TV malfunction.

Situation:

• Do not use when your hands are wet, with the cabinet removed,

or with attachments not recommended by the manufacturer.

Disconnect the TV set from AC power outlet (mains socket) and

antenna (aerial) during lightning storms.

• Do not install the TV so that it sticks out

into an open space. Injury or damage

from a person or object bumping into

the TV may result.

Broken pieces:

• Do not throw anything at the TV set. The screen glass may break

by the impact and cause serious injury.

• If the surface of the TV set cracks, do not touch it until you have

unplugged the AC power cord (mains lead). Otherwise electric

shock may result.

When not in use

• If you will not be using the TV set for several days, the TV set

should be disconnected from the AC power (mains) for

environmental and safety reasons.

• As the TV set is not disconnected from the AC power (mains)

when the TV set is just turned off, pull the plug from the AC

power outlet (mains socket) to disconnect the TV set

completely.

• However, some TV sets may have features that require the TV

set to be left in standby to work correctly.

For children

• Do not allow children to climb on the TV set.

• Keep small accessories out of the reach of children, so that they

are not mistakenly swallowed.

If the following problems occur...

Turn off the TV set and unplug the AC power cord (mains lead)

immediately if any of the following problems occur.

Ask your dealer or Sony service centre to have it checked by

qualified service personnel.

When:

 AC power cord (mains lead) is damaged.

 Poor fitting of AC power outlet (mains socket).

 TV set is damaged by being dropped, hit or having something

thrown at it.

 Any liquid or solid object falls through openings in the cabinet.

About LCD Monitor Temperature

When the LCD Monitor is used for an extended period, the panel

surrounds become warm. You may feel hot when touching there

by the hand.

WALL-MOUNT BRACKET

Below information shows the correct handling of the Wall-Mount

Bracket. Be sure to read this information thoroughly and use the

Wall-Mount Bracket correctly.

To Customers:

Be sure to observe the following precautions for safety to prevent

a serious injury through fire, electric shock, the product toppling

over, or the product dropping.

• Be sure to subcontract the installation to licensed contractors

and keep small children away during installation.

• Be sure to subcontract moving or dismounting of the TV to

licensed contractors.

• Do not remove screws, etc., after mounting the TV.

• Do not make alterations to the parts of the Wall-Mount Bracket.

• Do not mount any equipment other than the specified product.

• Do not apply any load other than the TV on the Wall-Mount

Bracket.

• Do not lean on or hang from the TV.

• Do not handle the TV with excessive force during cleaning or

maintenance.

To Sony Dealers and Contractors:

The following instructions are for Sony dealers and contractors

only. Be sure to read safety precautions described below and pay

special attention to safety during the installation, maintenance

and checking of this product.

• When handling or mounting the TV set, hold it on the sides. Do

not lift the TV by the U-shaped Bar.

• Do not install the Wall-Mount Bracket

on wall surfaces where the corners or

the sides of the TV are protruding

away from the wall surface.

• Do not install the TV over or under an

air conditioner.

• Be sure to install the Wall-Mount Bracket

securely to the wall following the

instructions in this instruction manual. If any

of the screws are loose or fall out, the Wall-

Mount Bracket may fall and cause injury or

property damage.

• Be sure to use the screws supplied with the

Wall-Mount Bracket when attaching the

Wall-Mount Bracket to the TV set. The

supplied screws are designed as indicated

by illustration when measured from the

attaching surface of the Wall-Mount Bracket. The diameter and

length of the screws differ depending on the Wall-Mount

Bracket model. Use of screws other than those supplied may

result in internal damage to the TV set or cause it to fall, etc.

See page 17 (Using the supplied Wall-Mount Bracket).

See page 23 (Using an optional Wall-Mount Bracket).

• Be sure to assemble the bracket properly following the

instructed procedure explained in this instruction manual.

• Be sure to tighten the screws securely in the designated

position.

• Be careful not to subject the TV to shock during installation.

U-shaped Bar

5

GB

• Be sure to install the TV on a wall that is both perpendicular and

flat.

• After proper installation of the TV, secure the cables properly.

• Do not allow the AC power cord

(mains lead) or the connecting

cables to be pinched as the

internal conductors may become

exposed and cause a short circuit

or an electrical break.

Viewing the TV

• View the TV in moderate light, as viewing the TV in poor light or

during long period of time, strains your eyes.

• When using headphones, adjust the volume so as to avoid

excessive levels, as hearing damage may result.

• Some people may experience discomfort (such as eye strain,

fatigue, or nausea) while watching 3D video images or playing

stereoscopic 3D games. Sony recommends that all viewers take

regular breaks while watching 3D video images or playing

stereoscopic 3D games. The length and frequency of necessary

breaks will vary from person to person. You must decide what

works best. If you experience any discomfort, you should stop

watching the 3D video images or playing stereoscopic 3D

games until the discomfort ends; consult a doctor if you believe

necessary. You should also review (i) the instruction manual of

any other device or media used with this television and (ii) our

website (http://www.sony-asia.com/support) for the latest

information. The vision of young children (especially those

under six years old) is still under development. Consult your

doctor (such as a pediatrician or eye doctor) before allowing

young children to watch 3D video images or play stereoscopic

3D games. Adults should supervise young children to ensure

they follow the recommendations listed above.

• Do not use, store, or leave the 3D Glasses or battery near a fire,

or in places with a high temperature, e.g., in direct sunlight, or

in sun-heated cars.

LCD Screen

• Although the LCD screen is made with high-precision

technology and 99.99% or more of the pixels are effective, black

dots may appear or bright points of light (red, blue, or green)

may appear constantly on the LCD screen. This is a structural

property of the LCD screen and is not a malfunction.

• Do not push or scratch the front filter, or place objects on top of

this TV set. The image may be uneven or the LCD screen may be

damaged.

• If this TV set is used in a cold place, a smear may occur in the

picture or the picture may become dark. This does not indicate a

failure. These phenomena disappear as the temperature rises.

• Ghosting may occur when still pictures are displayed

continuously. It may disappear after a few moments.

• The screen and cabinet get warm when this TV set is in use. This

is not a malfunction.

• The LCD screen contains a small amount of liquid crystal. Follow

your local ordinances and regulations for disposal.

Handling and cleaning the screen surface/

cabinet of the TV set

Be sure to unplug the AC power cord (mains lead) connected to

the TV set from AC power outlet (mains socket) before cleaning.

To avoid material degradation or screen coating degradation,

observe the following precautions.

• To remove dust from the screen surface/cabinet, wipe gently

with a soft cloth. If dust is persistent, wipe with a soft cloth

slightly moistened with a diluted mild detergent solution.

• Never spray water or detergent directly on

the TV set. It may drip to the bottom of the

screen or exterior parts and enter the TV set,

and may cause damage to the TV set.

• Never use any type of abrasive pad, alkaline/acid cleaner,

scouring powder, or volatile solvent, such as alcohol, benzene,

thinner or insecticide. Using such materials or maintaining

prolonged contact with rubber or vinyl materials may result in

damage to the screen surface and cabinet material.

• Do not touch the TV if your hand is covered in any chemical

substance such as hand cream or sunblock.

• Periodic vacuuming of the ventilation openings is

recommended to ensure to proper ventilation.

• When adjusting the angle of the TV set, move it slowly so as to

prevent the TV set from moving or slipping off from its table

stand.

Optional Equipment

Keep optional components or any equipment emitting

electromagnetic radiation away from the TV set. Otherwise

picture distortion and/or noisy sound may occur.

Wireless Function of the unit

• Do not operate this unit near medical equipment (pacemaker,

etc.), as malfunction of the medical equipment may result.

• Although this unit transmits/receives scrambled signals, be

careful of unauthorised interception. We cannot be responsible

for any trouble as a result.

Caution about handling the remote control

• Observe the correct polarity when inserting batteries.

• Do not use different types of batteries together or mix old and

new batteries.

• Dispose of batteries in an environmentally friendly way. Certain

regions may regulate the disposal of batteries. Please consult

your local authority.

• Handle the remote control with care. Do not drop or step on it,

or spill liquid of any kind onto it.

• Do not place the remote control in a location near a heat source,

a place subject to direct sunlight, or a damp room.

WALL-MOUNT BRACKET

• If you use the TV installed on the Wall-Mount Bracket for a long

time, the wall behind or above the TV may become discoloured

or the wallpaper may come unglued, depending on the material

of the wall.

• If the Wall-Mount Bracket is removed after installing it on the

wall, the screw holes remain.

• Do not use the Wall-Mount Bracket in a place where it is

subjected to mechanical vibration.

Precautions

6

GB

Parts and Controls

 Remote Control sensor* / Light sensor*

/ Illumination LED

The illumination LED lights up or blinks

according to the status of the TV.

•White

When turning on the TV/picture off

mode/software update, etc.

•Cyan

When connecting with a mobile device

wirelessly.

•Amber

Timer is set.

 (Power)

 CH +/- (Channel)

 +/- (Volume)

 (Input select)

Display and select the input source.

 TV

Switch to a TV channel or input from other

applications.

* Do not place anything near the sensor.

Controls and Indicators

7

GB

 LAN

 HDMI 3 AUDIO IN 

For HDMI 3 analogue audio connection.

 DIGITAL AUDIO OUT (OPTICAL)

/ VIDEO IN 1

For a composite connection*.

 VIDEO IN 2, / COMPONENT IN

• For a composite connection:

Use VIDEO IN, and  (L/R) of

/

COMPONENT IN*.

• For a component connection:

Use Y, P

B, PR, and  (L/R).

 (USB 1/2), (USB 3)

•Connecting a large USB device may

interfere with other connected devices

beside it.

• When connecting a large USB device,

connect to the USB 1 jack.

 AUDIO OUT /

To listen to the TV's sound through the

connected equipment, press HOME. Select

[Settings]  [Sound]  [Headphone/Audio

out] and then select the desired item.

 HDMI IN 1/3/4

• If the device has a DVI jack, connect it to

HDMI IN 3 through a DVI - HDMI adaptor

interface (not supplied), and connect the

device's audio out jack to HDMI 3 AUDIO

IN.

• If connecting a digital audio system that is

compatible with Audio Return Channel

(ARC) technology, use HDMI IN 4. If not, an

additional connection with DIGITAL AUDIO

OUT (OPTICAL) is necessary.

 HDMI IN 2/MHL

You can connect your MHL (Mobile High-

definition Link) device using an HD quality

MHL cable.

Inputs and Outputs

8

GB

 CABLE/ANTENNA

Connect to your cable or antenna (aerial).

* When connecting mono equipment, connect to the L

(MONO) audio jack.

9

GB

Using Remote Control

/ (Input select/Text hold)

In TV mode: Display and select the input

source.

In Text mode: Hold the current page.

 (TV standby)

Turn on or turn off the TV (standby mode).

DIGITAL/ANALOG

Switch between digital and analogue mode.

EXIT

Return to the previous screen or exit from

the menu. When an Interactive Application

service is available, press to exit from the

service.

 Number buttons

(Twin picture/PIP)*

1

*

2

Display two pictures simultaneously.

 (Text)

Display text information.

 Colour buttons

Execute correspondent function at that time.

(Wide mode)

Change the screen format.

TV

Switch to a TV channel or input from other

applications.

HELP

Display Help Menu.

Remote Control Parts Description

IR (infrared) Remote Control

Ȫ

ȩ

ȫ

Ȭ

ȭ

Ȯ

ȯ

Touchpad Remote Control

10

GB

 ACTION MENU

Display a list of contextual functions.

You can also display it by slide down your

finger from ACTION MENU on the Touchpad

Remote Control.

/ (Info/Text reveal)

Display information.

GUIDE/ *

1

Display the digital programme guide.

BACK

Return to previous screen.

HOME

Display the TV Home Menu.

DISCOVER

Bring up the Content Bar to search for

content.

You can also launch Content Bar by slide up

your finger from DISCOVER on the

Touchpad Remote Control.

//// (Item select/Enter)

 +/– (Volume)

Adjust the volume.

(Jump)

Jump back and forth between two channels

or inputs. The TV alternates between the

current channel or input and the last

channel or input that was selected.

 (Muting)

Mute the sound. Press again to restore the

sound.

PROG +/–//

In TV mode: Select the channel.

In Text mode: Select the next (

) or

previous (

) page.

 AUDIO

Change the language for the programme

currently being viewed.

(Subtitle setting)

Turn subtitles on or off (when the feature is

available).

//////

Operate media contents on TV and

connected BRAVIA Sync-compatible device.

SYNC MENU

Display the BRAVIA Sync Menu.

FOOTBALL

Turn Live Football Mode on or off (when the

feature is available).

 (Microphone)

Use Voice Function. (e.g., Search various

content by voice.)

 Touchpad

Operate the TV with the touchpad.

 (NFC)

Touch the device (e.g. some models of

Xperia) corresponding to the One-touch

mirroring function, then its screen is

displayed on the TV.

*1 The location, availability and function of remote

control button may vary depending on your country/

region/TV model.

*2 Twin Picture function will be available within 2015.

You will receive Twin Picture function automatically

as a network software upgrade. Make sure your TV is

connected to the Internet. If you do not have a

network connection, you will be able to download

the software from the Sony support website using

your PC. For details on how to upgrade, please visit

the Sony support website.

11

GB

Touchpad Remote Control can only be used

after pairing with the TV.

To pair, follow the pairing screen instruction.

Pairing screen can be displayed by pressing the

 button on the TV for 5 seconds, or select

[Settings] - [Touchpad Remote Control settings]

- [Pair Touchpad Remote Control].

1 Press HOME.

2 Select [Settings] - [Touchpad Remote

Control settings] - [Start Introduction/

Tutorial].

Attaching the Table-Top Stand

(Alternative)

You can change the Table-Top Stand from the

edge to the middle position by referring to the

instructions below.

Note

• Two or more people are needed to carry out this

installation.

• Be careful not to pinch the finger during installation.

KD-65X9000C

1

Using the Touchpad Remote Control

Launching the Touchpad Remote

Control Introduction/Tutorial

Middle position

Thick cushion

1.5 N∙m/1,5 N∙m

{15 kgf∙cm}

12

GB

2

KD-55X9000C

1 Remove the lower screws, and then one

of the Table-Top Stand.

2 Attach the stand plate (supplied with the

TV) to the detached Table-Top Stand.

3 Fix the stand plate to the Table-Top

Stand with screws (M5×10) (supplied

with the TV).

4 Attach the Table-Top Stand with stand

plate to the middle position, and fix with

screws (M6×32) (supplied with the TV).

5 Take the same procedure for the other

side of the Table-Top Stand.

6 Attach stand covers (supplied with the

TV).

Soft cloth

Stand plate

M5 × 10

1.5 N∙m/1,5 N∙m

{15 kgf∙cm}

M6 × 32

1.5 N∙m/1,5 N∙m

{15 kgf∙cm}

Stand cover

13

GB

Note

• Two or more people are needed to carry out this

installation.

• Ensure that there are no objects in front of the TV.

To bundle the cables

KD-65X9000C

KD-55X9000C

*1 Location of cable clamper when the Table-Top Stand

is attached to middle position.

*2 Location of cable clamper when the Table-Top Stand

is attached to edge position.

Note

• To detach the cable clamper from the TV, press the

top of the clamper , then pinch  as illustrated.

IR Sensor

*1

*2

*1

*2

14

GB

Connecting the TV

Note

• To select an input device connected to the TV, press

.

• When connecting the cable to the Cable/Antenna,

input finger tighten only, over-tightening the

connection can damage the TV.

To attach the terminal cover

After connecting cables, attach the terminal

cover.

To connect with an HDMI cable

To connect with component cables

Terminal

cover (left)

Terminal

cover (right)

To HDMI OUT

< 12 mm

< 21 mm

To AUDIO

OUT

To COMPONENT

OUT (P

R/PB/Y)

15

GB

To connect with AV composite cables To connect MHL device

The TV simultaneously charges the MHL-

compatible connected device while playing

photo/music/video files. You can use the TV

remote control to control the connected MHL-

compatible device.

Note

• If [MHL charging during standby] is set to [On], you can continue

charging the MHL-compatible device even when the TV is in

standby mode.

• Use authorized MHL 3 CABLE with MHL logo for 4K smartphone

or mobile devices.

To VIDEO

OUT

Use authorized MHL

CABLE with MHL logo

(not supplied)

MHL device

16

GB

Picture Quality

• AV composite cable

• Antenna (aerial) cable

Standard definition (SD) videos have picture signals with a

vertical resolution of 480 (NTSC) or 576 (PAL/SECAM) lines.

• Component cable • HDMI cable

High definition (HD) videos have picture signals

with a vertical resolution of 720 or 1,080 lines.

(For 4K vertical resolution: 2,160 lines)

17

GB

Installing the TV to the Wall

Your TV can be mounted on a wall using a Wall-Mount Bracket (supplied with the TV) out of the box as

packaged.

Prepare the TV for the Wall-Mount Bracket before making cable connections.

For product protection and safety reasons, Sony strongly recommends that installation of

your TV on the wall be performed by qualified professionals. Do not attempt to install it

yourself.

• Follow the instructions provided with the Wall-Mount Bracket for your model. Sufficient

expertise is required in installing this TV, especially to determine the strength of the wall for

withstanding the TV’s weight.

• The length of the screw for Wall-Mount Bracket differs depending on the Wall-Mount Bracket

thickness. Please see below illustration.

Note

• See page 4 (Safety Information) and page 5 (Precautions) on WALL-MOUNT BRACKET before carrying out Wall-Mount

Bracket installation.

• When attaching the Table-Top Stand again, be sure to fasten the screws (previously removed) to the original holes

on the rear of the TV.

1 Prepare necessary items.

Wall-Mount Bracket accessories

Using the supplied Wall-Mount Bracket

To Customers

Sufficient expertise is required for installing this product. Be sure to subcontract the installation to Sony

dealers or licensed contractors and pay special attention to safety during the installation. Sony is not liable

for any damages or injury caused by mishandling or improper installation, or installing any other than the

specified product. Your Statutory Rights (if any) are not affected.

To Sony Dealers and Contractors

Sufficient expertise is required for installing this product. Be sure to read this instruction manual thoroughly

to do the installation work safely. Sony is not liable for any damages or injury caused by mishandling or

improper installation.

Screw (M6)

Wall-Mount Bracket

8 mm - 12 mm

A Paper Template H Wall-Mount Bracket J U-shaped Bar

K Cushion

Lock plate (H1)

Lock pin (H2)

Wall-Mount Bracket (H3)

18

GB

Screws for Wall-Mount Bracket (8 mm in diameter, not supplied) (4)

2 Remove the screws from the rear of the TV before attaching the U-shaped Bar.

3 Attach the U-shaped Bar J (supplied with the TV) to the rear of the TV.

4 Attach the cushions K to the rear of the TV.

M6 × 16

M6 × 16 (previously removed)

U-shaped Bar J

1.5 N∙m/1,5 N∙m

{15 kgf∙cm}

Cushions K

19

GB

5 Make sure that the wall has enough space for the TV and is capable of supporting a

weight of at least four times that of the TV.

Refer to the following table on installing the TV to the wall. See page 28-31

(Specifications) for the TV’s weight.

Unit: mm

Note

• Figures in the table may differ slightly depending on the installation.

6 Pull the lock pin (H2) and detach the lock plate (H1) from Wall-Mount Bracket (H3).

Model Name

KD-

Display dimensions

Screen

center

dimension

Length for mounting

65X9000C 1,451 835 325 747 40

55X9000C 1,232 712 263 624 40

Screen center point

Wall-Mount

Bracket (H3)

Lock plate (H1)

Lock

pin (H2)

20

GB

7 Tape the Paper Template A to the wall and drill holes according to the numbering on the

Paper Template A using an electric drill.

8 Remove the Paper Template A off from the wall.

9 Attach the Wall-Mount Bracket (H3) (supplied with the TV) to the wall correctly using the

screws (8 mm in diameter, not supplied).

10 Remove the terminal covers and detach the Table-Top Stand from the TV while holding

the bottom of the TV.

Wall

A

Wall

Wall-Mount Bracket (H3)

ページが読み込まれています...

Sony KD-55X9000C リファレンスガイド

Sony KD-55X9000C リファレンスガイド

他の言語で

関連論文