Dell PowerEdge R805 クイックスタートガイド

Dell™ PowerEdge™

R805 Systems

Getting Started

With Your System

系统使用入门

はじめに

시스템시작하기

Dell™ PowerEdge™

R805 Systems

Getting Started

With Your System

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly

forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; AMD and AMD

Opteron are registered trademarks of Advanced Micro Devices; Microsoft, Windows, and Windows

Server are registered trademarks of Microsoft Corporation; Novell and NetWare are registered

trademarks of Novell, Inc.; Red Hat and Red Hat Enterprise Linux are registered trademarks

of Red Hat, Inc.; SUSE is a registered trademark of Novell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Model EMS01

August 2007 P/N CR241 Rev. A00

Getting Started With Your System 3

System Features

This section describes the major hardware and software features of your

system. It also provides information about other documents you may need

when setting up your system and how to obtain technical assistance.

• Two dual-core or quad-core AMD Opteron™ processors.

• A minimum of 2 GB single- or dual-ranked 667-MHz DDR2 (PC2-5300)

memory modules (installed in two sets of pairs). Memory is upgradable to

a maximum of 128 GB by installing combinations of 512-MB, 1-GB, 2-GB,

4-GB, or 8-GB memory modules in the 16 memory module sockets

(eight per CPU) on the system board.

• Support for up to two 2.5-inch, internal hot-pluggable Serial Attached

SCSI (SAS) or SATA hard drives.

• An optional slim-line SATA DVD-ROM drive, slim-line SATA DVD-RW

drive, or combination CD-RW/DVD drive (when available).

NOTE: DVD devices are data only.

• An intrusion switch that signals the appropriate systems management

software if the cover is opened.

• Up to two hot-pluggable, 700-W power supplies in an optional 1 + 1

redundant configuration.

• Six hot-pluggable system cooling fans.

• Optional support for iSCSI boot.

The system board includes the following features:

• A right riser card (riser 1) containing two PCIe (x4 and x8) slots. The right

riser card also contains an SD (Secure Digital) slot for embedded OS

support.

• A left riser card (riser 2) containing one full-length PCIe (x8) slot

and one half-length PCIe (x8) slot.

• An integrated SAS controller card (via a dedicated PCIe slot on the

sideplane board) supporting both SAS 6i/R and PERC 6/i adapters.

• Optional integrated PERC controller (PERC 6i) with integrated cache

and battery backup.

• Four integrated Gigabit Ethernet NICs, capable of supporting 10-Mbps,

100-Mbps, and 1000-Mbps data rates.

4 Getting Started With Your System

• Four external USB 2.0-compliant connectors (two on the front and two

on the back) supporting a diskette drive, a DVD-ROM drive, a keyboard,

a mouse, or a USB flash drive.

• One internal USB 2.0-compliant connector supporting an optional

bootable USB flash drive or USB security key.

• Optional remote access controller (RAC) for remote systems management.

• An integrated VGA-compatible video subsystem based on an integrated

ATI ES1000 33-MHz PCI video controller. The video subsystem includes

32MB of graphics memory and supports various 2D graphics video modes.

Maximum resolution is 1600x1200 with 65,536 colors. (When the optional

RAC is installed, the maximum resolution of the integrated video

subsystem is 1280x1024.)

• Systems management circuitry that monitors operation of the system fans

as well as critical system voltages, temperatures, and system power

consumption. The systems management circuitry works in conjunction

with the systems management software.

• Standard Baseboard Management Controller (BMC) with serial and LAN

access.

• Back-panel connectors include one serial, one video, two USB,

and four NIC connectors.

• Front-panel connectors include a video and two USB connectors.

• Front-panel 1x5 LCD for system ID and error messaging.

• System ID button on the front and back panels.

For more information about specific features, see Technical Specifications.

Supported Operating Systems

• Microsoft

®

Windows Server

®

2003 R2 Standard and Enterprise Editions

(SP1 and later)

• Microsoft Windows Server 2003 R2 Standard and Enterprise x64 Editions

(SP1 and later)

• Red Hat Enterprise Linux Server 5 (x86)

• Red Hat Enterprise Linux Server 5 (x86_64)

• Red Hat Enterprise Linux Server ES (Version 4.5) (x86)

Getting Started With Your System 5

• Red Hat Enterprise Linux Server ES (Version 4.5) (x86_64)

•SUSE

®

Linux Enterprise Server 9 (x86_64)

• SUSE Linux Enterprise Server 10 (x86_64)

•VMware

®

ESX Server 3 (including embedded versions)

NOTE: For the latest information on supported operating systems, see www.dell.com.

NOTE: SUSE Linux Enterprise Server 9, prior to SP4, does not support SATA optical

devices. Installation must be performed using other methods, such as an external

USB CD-ROM drive.

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and

regulatory information. Warranty information may be included within this

document or as a separate document.

• The

Rack Installation Guide

or

Rack Installation Instructions

included

with your rack solution describes how to install your system into a rack.

• The

Hardware Owner’s Manual

provides information about system

features and describes how to troubleshoot the system and install or

replace system components.

• CDs included with your system provide documentation and tools for

configuring and managing your system.

• Systems management software documentation describes the features,

requirements, installation, and basic operation of the software.

• Operating system documentation describes how to install (if necessary),

configure, and use the operating system software.

• Documentation for any components you purchased separately provides

information to configure and install these options.

• Updates are sometimes included with the system to describe changes

to the system, software, and/or documentation.

NOTE: Always check for updates on support.dell.com and read the updates

first because they often supersede information in other documents.

• Release notes or readme files may be included to provide last-minute

updates to the system or documentation or advanced technical reference

material intended for experienced users or technicians.

6 Getting Started With Your System

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does

not perform as expected, see your Hardware Owner’s Manual.

Dell™ Enterprise Training and Certification is available; see

www.dell.com/

training

for more information. This service may not be offered in all locations.

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the

safety instructions and important regulatory information in your Product

Information Guide.

This section describes the steps to set up your system for the first time.

Unpacking the System

Unpack your system and identify each item.

Keep all shipping materials in case you need them later.

NOTE: Depending on options ordered, not all components shown may be

included.

Getting Started With Your System 7

Installing the Rails and System in a Rack

Once you have read the "Safety Instructions" located in the rack

installation documentation for your system, install the rails and the system

in the rack.

See your rack installation documentation for instructions on installing

your system in a rack.

Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating

which cable to plug into each connector. Be sure to tighten the screws

(if any) on the monitor's cable connector.

8 Getting Started With Your System

Connecting the Power

Connect the monitor’s power cable to the monitor (optional), and connect

the system’s power cable(s) to the system.

Installing the Power Cord Retention Bracket

Attach the power cord retention bracket on the right bend of the power

supply handle. Bend the system power cable into a loop as shown in the

illustration and attach to the bracket’s cable clasp. Repeat the procedure

for the second power supply.

Plug the other end of the power cables into a grounded electrical outlet

or a separate power source such as an uninterrupted power supply (UPS)

or a power distribution unit (PDU).

Getting Started With Your System 9

Turning on the System

Turn on the system and monitor (optional).

With the bezel removed, press the power button on the system and the

monitor. The power indicators should light. Adjust the monitor's controls

until the displayed image is satisfactory.

Installing the Bezel

Install the bezel (optional).

10 Getting Started With Your System

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system for

the first time, see the Quick Installation Guide. Be sure the operating system

is installed before installing hardware or software not purchased with the

system.

Technical Specifications

Processor

Processor type Two dual- or quad-core AMD Opteron processors

Expansion Bus

Bus type PCIe

Expansion slots

Right riser (riser 1):

PCIe

One x8 full-height, full-length slot (top)

One x4 full-height, half-length slot (bottom)

One internal SD (Secure Digital) card slot

Left riser (riser 2):

PCIe

One x8 full-height, full-length slot (top)

One x8 full-height, half-length slot (bottom)

One internal USB key socket

Memory

Architecture 667-MHz registered parity DDR2 memory

modules

Memory module sockets 16 240-pin

Memory module capacities 512 MB, 1 GB, 2 GB, 4 GB, or 8 GB (single-

or dual-rank only, quad-rank not supported)

Minimum RAM

(installed in two sets of pairs)

2 GB (1 GB each processor, 2 DIMMs

per processor)

Maximum RAM 128 GB (64 GB each processor)

Getting Started With Your System 11

Drives

Hard drives Up to two 2.5-inch, hot-plug SAS or SATA

internal drives

Optical drive One optional slim-line SATA DVD-ROM drive or

DVD-RW drive, or combination CD-RW/DVD

drive (when available)

NOTE: DVD devices are data only.

External optional USB DVD

Flash drive External optional USB

Internal optional USB

Internal optional SD card

Connectors

Back

NIC

Four RJ-45 10/100/1000

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin VGA

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

One 4-pin, USB 2.0-compliant

SD

One flash memory card slot on right PCIe riser

(riser 1)

Video

Video type ATI ES1000 video controller; VGA connector

Video memory 32 MB

12 Getting Started With Your System

Power

AC power supply (per power supply)

Wa tt ag e

700 W

Voltage

85–264 VAC, autoranging, 47–63 Hz

Heat dissipation

2697 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over the entire

system ambient operating range, the inrush

current may reach 55 A per power supply

for 10 ms or less.

Batteries

System battery

CR 2032 3.0-V lithium ion coin cell

RAID battery (optional)

4.1-V lithium ion

Physical

Height

8.67 cm (3.41 in)

Width

44.4 cm (17.5 in)

Depth

71.26 cm (28.05 in)

Weight (maximum

configuration)

20.23 kg (44.6 lb)

Getting Started With Your System 13

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see www.dell.com/environmental_datasheets.

Temperature

Operating

10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1ºF/550 ft.

Storage

–40° to 65°C (–40° to 149°F) with a maximum

temperature gradation of 20°C per hour

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing) with a maximum

humidity gradation of 10% per hour

Maximum vibration

Operating

0.26 Grms at 5–350 Hz in operational

orientations

Storage

1.54 Grms at 10–250 Hz in all orientations

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse

on each side of the system) of 31 G for 2.6 ms

in the operational orientation

Storage

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse

on each side of the system) of 71 G for up to 2 ms

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1ºF/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

14 Getting Started With Your System

Dell™ PowerEdge™ R805

系统

系统使用入门

型号

EMS01

注、注意和警告

注：“注”表示可以帮助您更好地使用计算机的重要信息。

注意：“注意”表示可能会损坏硬件或导致数据丢失，并告诉您如何避免

此类问题。

警告：“警告”表示可能会出现导致财产损失、人身伤害甚至死亡的情况。

____________________

本说明文件中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式进行复制。

本文中使用的商标：

Dell

和

DELL

徽标是

Dell Inc.

的商标；

AMD

和

AMD Opteron

是

Advanced Micro Devices

的注册商标；

Microsoft

、

Windows

和

Windows Server

是

Microsoft

Corporation

的注册商标；

Novell

和

NetWare

是

Novell, Inc.

的注册商标；

Red Hat

和

Red Hat

Enterprise Linux

是

Red Hat, Inc.

的注册商标；

SUSE

是

Novell Inc.

的注册商标。

本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。

Dell Inc.

对本公司的商标和产品名称之外的其它商标和产品名称不拥有任何专有权。

型号

EMS01

2007

年

8

月

P/N CR241 Rev. A00

系统使用入门 17

系统配置

本节介绍系统的主要硬件和软件配置。另外，还介绍了有关在安装系统时

可能需要的其它说明文件的信息，以及如何获得技术帮助的信息。

•

两个双核或四核

AMD Opteron™

处理器。

•

最低

2 GB

单排或双排

667 MHz DDR2 (PC2-5300)

内存模块（两组成

对安装）。通过在系统板上的

16

个内存模块插槽（每个

CPU

八个）

中安装

512 MB

、

1 GB

、

2 GB

、

4 GB

或

8 GB

内存模块组合，最大可将

内存升级到

128 GB

。

•

支持最多两个

2.5

英寸内部热插拔串行连接

SCSI (SAS)

或

SATA

硬盘

驱动器。

•

可选的细长型

SATA DVD-ROM

驱动器、细长型

SATA DVD-RW

驱动

器或组合

CD-RW/DVD

驱动器（可用时）。

注：DVD 设备仅用于数据。

•

防盗开关，在盖被打开时会向相应的系统管理软件发送信号。

•

最多两个

700 W

热插拔电源设备（可选

1 + 1

冗余配置）。

•

六个热插拔系统冷却风扇。

•

可选的

iSCSI

引导支持。

系统板包含以下配置：

•

包含两个

PCIe

（

x4

和

x8

）插槽的右提升卡（提升卡

1

）。右提升卡还

包含一个用于嵌入式

OS

支持的

SD

（安全数字）插槽。

•

包含一个全长

PCIe (x8)

插槽和一个半长

PCIe (x8)

插槽的左提升卡

（提升卡

2

）。

•

一个集成的

SAS

控制器卡，（通过侧板上的专用

PCIe

插槽）

支持

SAS 6i/R

和

PERC 6/i

适配器。

•

可选的集成

PERC

控制器

(PERC 6i)

，具有集成高速缓存和备用电池。

•

四个集成的千兆位以太网

NIC

，可支持

10 Mbps

、

100 Mbps

和

1000 Mbps

数据速率。

•

四个外部

USB 2.0

兼容连接器（两个在正面，两个在背面），可支持

软盘驱动器、

DVD-ROM

驱动器、键盘、鼠标或

USB

快擦写驱动器。

•

一个内部

USB 2.0

兼容连接器，可支持一个可选的可引导

USB

快擦写

驱动器或

USB

安全保护密钥。

•

可选的远程访问控制器

(RAC)

，用于远程系统管理。

18 系统使用入门

•

一个基于集成的

ATI ES1000 33-MHz PCI

视频控制器的

VGA

兼容集成

视频子系统。此视频子系统包含

32 MB

的图形内存，并支持各种

2D

图形视频模式。最大分辨率为

1600 x 1200

（

65,536

色）。（如果安装

了可选的

RAC

，则集成视频子系统的最大分辨率为

1280x1024

。）

•

系统管理电路，可监测系统风扇的运行以及系统临界电压、温度和系

统电源消耗。系统管理电路需要与系统管理软件配合工作。

•

标准底板管理控制器

(BMC)

，支持串行访问和

LAN

访问。

•

背面板连接器包括一个串行连接器、一个视频连接器、两个

USB

连接

器和四个

NIC

连接器。

•

前面板连接器包括一个视频连接器和两个

USB

连接器。

•

前面板

1x5 LCD

显示屏，用于显示系统

ID

和错误信息。

•

系统

ID

按钮，位于前面板和背面板上。

有关特定配置的详细信息，请参阅技术规格。

支持的操作系统

•

Microsoft

®

Windows Server

®

2003 R2

标准版和企业版（

SP1

和更高版本）

•

Microsoft Windows Server 2003 R2 x64

标准版和企业版（

SP1

和更高版本）

•

Red Hat Enterprise Linux Server 5 (x86)

•

Red Hat Enterprise Linux Server 5 (x86_64)

•

Red Hat Enterprise Linux Server ES

（

4.5

版）

(x86)

•

Red Hat Enterprise Linux Server ES

（

4.5

版）

(x86_64)

•

SUSE

®

Linux Enterprise Server 9 (x86_64)

•

SUSE Linux Enterprise Server 10 (x86_64)

•

VMware

®

ESX Server 3

（包括嵌入式版本）

注：有关支持的操作系统的最新信息，请参阅 www.dell.com。

注：SUSE Linux Enterprise Server 9（SP4 以前的版本）不支持 SATA 光驱。

必须使用其它方法（如外部 USB CD-ROM 驱动器）才能进行安装。

ページを読み込んでいます...

Dell PowerEdge R805 クイックスタートガイド

関連論文