Dell PowerEdge 2970 クイックスタートガイド

www.dell.com | support.dell.com

Dell™ PowerEdge™ 2970 Systems

Getting Started With

Your System

系统使用入门

はじめに

시스템시작하기

Model EMS01

www.dell.com | support.dell.com

Dell™ PowerEdge™ 2970 Systems

Getting Started With

Your System

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; AMD and AMD Opteron are registered trademarks of

Advanced Micro Devices; Microsoft, Windows, and Windows Server are registered trademarks of Microsoft Corporation; Novell and NetWare

are registered trademarks of Novell, Inc.; Red Hat and Red Hat Enterprise Linux are registered trademarks of Red Hat, Inc.; SUSE is a registered

trademark of Novell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

Model EMS01

January 2007 P/N XM224 Rev. A00

Getting Started With Your System 3

System Features

This section describes the major hardware and software features of your system. It also provides

information about other documents you may need when setting up your system and how to obtain

technical assistance.

• One or two dual-core AMD Opteron™ processors. One or two quad-core AMD Opteron™

processors (when available).

• A minimum of 1 GB (single-processor systems) or 2 GB (two-processor systems) of 667-MHz

registered parity DDR-II memory modules. Memory is upgradable to a maximum of 32 GB

(two-processor systems) by installing combinations of 512-MB, 1-GB, 2-GB, or 4-GB memory

modules in the eight memory module sockets on the system board. (64 GB of memory will be

supported when 8 GB memory modules are available.)

• Support for up to eight 2.5-inch, internal hot-pluggable Serial Attached SCSI (SAS) or

SATA hard drives.

• The optional media bay provides support for an optional half-height tape backup unit (TBU)

and an optional slim-line 1.44-MB diskette drive.

• An optional slim-line IDE CD, DVD, or combination CD-RW/DVD drive.

NOTE: DVD devices are data only.

• An intrusion switch that signals the appropriate systems management software if the cover

is opened.

• Up to two hot-pluggable, 750-W power supplies in an optional 1 + 1 redundant configuration.

• Four hot-pluggable system cooling fans.

The system board includes the following features:

• A left riser card that has one full-length PCIe x8 lane slot and one half-length PCIe x4 lane slot.

• A center riser card that has one half-length PCIe x8 lane slot.

• A dedicated slot for an integrated SAS host bus adapter, which supports up to four 2.5-inch SAS

or SATA hard drives, or an optional RAID controller card with 256 MB of cache memory and

a RAID battery, which supports up to eight 2.5-inch SAS or SATA hard drives.

NOTE: System boot is not supported from an external device attached to a SAS or SCSI adapter,

including SAS 5/E, PERC 5/E, or PERC 4e/DC. See support.dell.com for the latest support information

about booting from external devices.

• Two integrated Gigabit Ethernet NICs, capable of supporting 10-Mbps, 100-Mbps,

and 1000-Mbps data rates.

4 Getting Started With Your System

• Four external USB 2.0-compliant connectors (two on the front and two on the back) supporting

a diskette drive, a DVD-ROM drive, a keyboard, a mouse, or a USB flash drive.

• One internal USB 2.0-compliant connector supporting an optional bootable USB flash drive

for customized boot configurations.

• Optional remote access controller (RAC) for remote systems management.

• An integrated VGA-compatible video subsystem based on an integrated ATI ES1000 33-MHz PCI

video controller. The video subsystem includes 32MB of graphics memory and supports various

2D graphics video modes. Maximum resolution is 1600x1200 with 65,536 colors. (When the optional

RAC is installed, the maximum resolution of the integrated video subsystem is 1280x1024.)

• Systems management circuitry that monitors operation of the system fans as well as critical system

voltages and temperatures. The systems management circuitry works in conjunction with the systems

management software.

• Standard Baseboard Management Controller (BMC) with serial and LAN access.

• Back-panel connectors include one serial, one video, two USB, and two NIC connectors.

• Front-panel connectors include a video and two USB connectors.

• Front-panel 1x5 LCD for system ID and error messaging.

• System ID button on the front and back panels.

For more information about specific features, see Technical Specifications.

Supported Operating Systems

• Microsoft

®

Windows Server

®

2003 R2 Standard and Enterprise Editions (SP1 and later)

• Microsoft Windows Server 2003 R2 Standard and Enterprise x64 Editions (SP1 and later)

•Red Hat

®

Enterprise Linux

®

AS and ES (Version 4) (x86)

•Red Hat

®

Enterprise Linux

®

AS and ES (Version 4) (x86_64)

• Red Hat Enterprise Linux Server 5 (x86)

• Red Hat Enterprise Linux Server 5 (x86_64)

•SUSE

®

Linux Enterprise Server 10 (x86_64)

NOTE: For the latest information on supported operating systems, see www.dell.com.

Getting Started With Your System 5

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and regulatory information.

Warranty information may be included within this document or as a separate document.

• The

Rack Installation Guide

or

Rack Installation Instructions

included with your rack solution

describes how to install your system into a rack.

• The

Hardware Owner’s Manual

provides information about system features and describes how

to troubleshoot the system and install or replace system components.

• CDs included with your system provide documentation and tools for configuring and managing

your system.

• Systems management software documentation describes the features, requirements, installation,

and basic operation of the software.

• Operating system documentation describes how to install (if necessary), configure, and use

the operating system software.

• Documentation for any components you purchased separately provides information to configure

and install these options.

• Updates are sometimes included with the system to describe changes to the system, software,

and/or documentation.

NOTE: Always check for updates on support.dell.com and read the updates first because they often

supersede information in other documents.

• Release notes or readme files may be included to provide last-minute updates to the system or

documentation or advanced technical reference material intended for experienced users or technicians.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does not perform as expected,

see your Hardware Owner’s Manual.

Dell™ Enterprise Training and Certification is available; see www.dell.com/training for more

information. This service may not be offered in all locations.

Installation and Configuration

CAUTION: Before performing the following procedure, read and follow the safety instructions and important

regulatory information in your Product Information Guide.

This section describes the steps to set up your system for the first time.

6 Getting Started With Your System

Unpacking the System

Unpack your system and identify each item.

Keep all shipping materials in case you need them later.

Installing the Rails and System in a Rack

Once you have read the "Safety Instructions" located in the rack installation documentation

for your system, install the rails and the system in the rack.

See your rack installation documentation for instructions on installing your system in a rack.

Getting Started With Your System 7

Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to plug into

each connector. Be sure to tighten the screws (if any) on the monitor's cable connector.

Connecting the Power

Connect the monitor’s power cable to the monitor (optional), and connect the system’s power

cable(s) to the system.

8 Getting Started With Your System

Installing the Power Cord Retention Bracket

Attach the power cord retention bracket on the right bend of the power supply handle. Bend

the system power cable into a loop as shown in the illustration and attach to the bracket’s cable

clasp. Repeat the procedure for the second power supply.

Plug the other end of the power cables into a grounded electrical outlet or a separate power source

such as an uninterrupted power supply (UPS) or a power distribution unit (PDU).

Turning on the System

Turn on the system and monitor (optional).

With the bezel removed, press the power button on the system and the monitor. The power

indicators should light. Adjust the monitor's controls until the displayed image is satisfactory.

Getting Started With Your System 9

Installing the Bezel

Install the bezel (optional).

Complete the 0perating System Setup

If you purchased a preinstalled operating system, see the operating system documentation that ships with

your system. To install an operating system for the first time, see the Quick Installation Guide. Be sure the

operating system is installed before installing hardware or software not purchased with the system.

Technical Specifications

Processor

Processor type One or two dual-core AMD Opteron processors

One or two quad-core AMD Opteron processors

(when available)

Expansion Bus

Bus type PCIe

Expansion slots

Center riser:

PCIe

One x8 full-height, half-length 3.3-V slot

Left riser

PCIe option:

One x8 full-height, full-length 3.3-V slot

One x4 full-height, half-length 3.3-V slot

10 Getting Started With Your System

Memory

Architecture 667-MHz registered parity DDR-II memory

modules

Memory module sockets Eight 240-pin

Memory module capacities 512 MB, 1 GB, 2 GB, or 4 GB

(8 GB when available)

Minimum RAM 1 GB (one processor) or 2 GB (two processors)

Maximum RAM 16 GB (one processor) or 32 GB (two processors)

(32 GB (one processor) or 64 GB (two processors)

when 8 GB memory modules are available)

Drives

Hard drives Up to eight 2.5-inch, hot-plug SAS or SATA

internal drives

Diskette drive One optional slimline 1.44-MB

External optional USB 1.44-MB

Optical drive One optional slimline IDE CD, DVD,

or combination CD-RW/DVD

NOTE: DVD devices are data only.

External optional USB DVD

Tape drive One optional internal half-height tape backup

device

Flash drive External optional USB

Internal optional USB

Connectors

Back

NIC

Two RJ-45 (for integrated 1-GB NICs)

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin VGA

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

One 4-pin, USB 2.0-compliant

Getting Started With Your System 11

Video

Video type ATI ES1000 video controller; VGA connector

Video memory 32 MB

Power

AC power supply (per power supply)

Wattage

750 W

Voltage

85–264 VAC, autoranging, 47–63 Hz

Heat dissipation

2697 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over the entire

system ambient operating range, the inrush

current may reach 55 A per power supply for

10 ms or less.

Batteries

System battery

CR 2032 3.0-V lithium ion coin cell

RAID battery (optional)

4.1-V lithium ion

Physical

Rack

Height

8.656 cm (3.40 in)

Width

44.7 cm (17.6 in)

Depth

75.68 cm (29.79 in)

Weight (maximum configuration)

26.76 kg (59 lb)

Environmental

NOTE: For additional information about environmental measurements for specific system configurations,

see www.dell.com/environmental_datasheets.

Temperature

Operating

10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1ºF/550 ft.

Storage

–40° to 65°C (–40° to 149°F) with a maximum

temperature gradation of 20°C per hour

12 Getting Started With Your System

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing) with a maximum

humidity gradation of 10% per hour

Maximum vibration

Operating

0.26 Grms at 5–350 Hz in operational

orientations

Storage

1.54 Grms at 10–250 Hz in all orientations

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse

on each side of the system) of 31 G for 2.6 ms

in the operational orientation

Storage

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse

on each side of the system) of 71 G for up to 2 ms

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1ºF/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Environmental (continued)

www.dell.com | support.dell.com

Dell™ PowerEdge™ 2970 系统

系统使用入门

注、注意和警告

注：注表示可以帮助您更好地使用计算机的重要信息。

注意：注意表示可能会损坏硬件或导致数据丢失，并告诉您如何避免此类问题。

警告：警告表示可能会导致财产损失、人身伤害甚至死亡。

____________________

本说明文件中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式进行复制。

本文中使用的商标：

Dell

和

DELL

徽标是

Dell Inc.

的商标；

AMD

和

AMD Opteron

是

Advanced Micro Devices

的注册商标；

Microsoft

、

Windows

和

Windows Server

是

Microsoft Corporation

的注册商标；

Novell

和

NetWare

是

Novell, Inc.

的注册商标；

Red Hat

和

Red Hat Enterprise Linux

是

Red Hat, Inc.

的注册商标；

SUSE

是

Novell Inc.

的注册商标。

本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。

Dell Inc.

对本公司的商标和产

品名称之外的其它商标和产品名称不拥有任何专有权。

型号

EMS01

2007

年

1

月

P/N XM224

修订版

A00

系统使用入门 15

系统配置

本节介绍系统的主要硬件和软件配置。还介绍了有关在安装系统时可能需要的其它说明

文件的信息，以及如何获得技术帮助的信息。

•

一个或两个双核心

AMD Opteron™

处理器。一个或两个四核心

AMD Opteron™

处理器

（可用时）。

•

至少

1 GB

（单处理器系统）或

2 GB

（双处理器系统）的

667 MHz

带寄存器的奇偶校验

DDR-II

内存模块。通过在系统板上的八个内存模块插槽中安装

512 MB

、

1 GB

、

2 GB

或

4 GB

内存模块组合，可将内存升级到最大

32 GB

（双处理器系统）。（提供

8 GB

内存模

块时，将支持

64 GB

内存。）

•

支持多达八个

2.5

英寸内部热插拔串行连接

SCSI (SAS)

或

SATA

硬盘驱动器。

•

可选介质托盘支持一个可选半高磁带备份装置

(TBU)

和一个可选的细长型

1.44-MB

软盘驱动器。

•

一个可选的细长型

IDE CD

、

DVD

或组合

CD-RW/DVD

驱动器。

注：DVD 设备仅用于数据。

•

防盗开关，在盖被打开时会向相应的系统管理软件发送信号。

•

多达两个

750 W

热插拔电源设备（可选

1 + 1

冗余配置）。

•

四个热插拔系统冷却风扇。

系统板包含以下配置：

•

具有一个全长

PCIe x8

信道插槽和一个半长

PCIe x4

信道插槽的左提升卡。

•

具有一个半长

PCIe x8

信道插槽的中心提升卡。

•

一个专用插槽，用于安装集成的

SAS

主机总线适配器（最多可支持四个

2.5

英寸

SAS

或

SATA

硬盘驱动器），或一个配有

256 MB

高速缓存和

RAID

电池的可选

RAID

控制器卡

（最多可支持八个

2.5

英寸

SAS

或

SATA

硬盘驱动器）。

注：不支持从连接到 SAS 或 SCSI 适配器的外部设备引导系统，包括 SAS 5/E、PERC 5/E 或

PERC 4e/DC。有关支持从外部设备引导的最新信息，请参阅 support.dell.com。

•

两个集成的千兆位以太网

NIC

，可支持

10 Mbps

、

100 Mbps

和

1000 Mbps

数据速率。

•

四个外部

USB 2.0

兼容连接器（两个在正面，两个在背面），可支持软盘驱动器、

DVD-ROM

驱动器、键盘、鼠标或

USB

快擦写驱动器。

•

一个内部

USB 2.0

兼容连接器，可支持一个可选的可引导

USB

快擦写驱动器，

以用于定制的引导配置。

•

可选的远程访问控制器

(RAC)

，用于远程系统管理。

16 系统使用入门

•

一个基于集成的

ATI ES1000 33-MHz PCI

视频控制器的

VGA

兼容集成视频子系统。此视频子系统

包含

32 MB

的图形内存，并支持各种

2D

图形视频模式。最大分辨率为

1600 x 1200

（

65,536

色）。

（如果安装了可选的

RAC

，则集成视频子系统的最大分辨率为

1280x1024

。）

•

系统管理电路，可监测系统风扇的运行以及系统临界电压和温度。系统管理电路需要与系统管理

软件配合工作。

•

标准底板管理控制器

(BMC)

，支持串行访问和

LAN

访问。

•

背面板连接器包括一个串行连接器、一个视频连接器、两个

USB

连接器和两个

NIC

连接器。

•

前面板连接器包括一个视频连接器和两个

USB

连接器。

•

前面板

1x5 LCD

显示屏，用于显示系统

ID

和错误信息。

•

系统

ID

按钮，位于前面板和背面板上。

有关特定配置的详细信息，请参阅技术规格。

支持的操作系统

•

Microsoft

®

Windows Server

®

2003 R2

标准版和企业版（

SP1

和更高版本）

•

Microsoft Windows Server 2003 R2 x64

标准版和企业版（

SP1

和更高版本）

•

Red Hat

®

Enterprise Linux

®

AS

和

ES

（第

4

版）

(x86)

•

Red Hat

®

Enterprise Linux

®

AS

和

ES

（第

4

版）

(x86_64)

•

Red Hat Enterprise Linux Server 5 (x86)

•

Red Hat Enterprise Linux Server 5 (x86_64)

•

SUSE

®

Linux Enterprise Server 10 (x86_64)

注：有关支持的操作系统的最新信息，请参阅 www.dell.com。

系统使用入门 17

您可能需要的其它信息

警告：《产品信息指南》，提供了重要的安全信息和管制信息。保修信息可能包括在该说明文件中，

也可能作为单独的说明文件提供。

•

随机架解决方案附带的《机架安装指南》或《机架安装说明》，介绍了如何在机架中安装系统。

•

《硬件用户手册》提供了有关系统部件的信息，并介绍了如何排除系统故障以及如何安装或更换

系统组件。

•

随系统附带的

CD

提供了用于配置和管理系统的说明文件和工具。

•

系统管理软件说明文件，介绍了软件的功能、要求、安装和基本操作。

•

操作系统说明文件，介绍了如何安装（如果有必要）、配置和使用操作系统软件。

•

单独购买的任何组件所附带的说明文件，提供了有关配置和安装这些选件的信息。

•

系统有时附带更新，用于说明对系统、软件和

/

或说明文件所做的更改。

注：请始终检查 support.dell.com 上的更新信息并首先进行阅读，因为该网站上的信息常常会取代其

它说明文件中的信息。

•

系统可能附带版本注释或自述文件，以提供系统或说明文件的最新更新内容，或者为有经验的用

户或技术人员提供高级技术参考资料。

获得技术帮助

如果您对本指南中的过程有疑问，或系统运行无法达到预期效果，请参阅《硬件用户手册》。

Dell

™

可以提供企业培训与认证；有关详情，请访问

www.dell.com/training

。并非在所有国家和地

区均可提供此服务。

安装和配置

警告：在执行以下过程之前，请阅读并遵循《产品信息指南》中的安全说明和重要的管制信息。

本节介绍初次安装系统时的步骤。

18 系统使用入门

打开系统包装

打开系统包装并识别每项物品。

妥善保管好所有运输包装材料，以备将来使用。

在机架中安装滑轨和系统

在仔细阅读了系统的机架安装说明文件中的“安全说明”之后，在机架中安装滑轨和系统。

有关在机架中安装系统的说明，请参阅机架安装说明文件。

ページを読み込んでいます...

Dell PowerEdge 2970 クイックスタートガイド

Dell PowerEdge 2970 クイックスタートガイド

他の言語で

関連論文