Red Sea REEFER 300 G2 取扱説明書

REEFER™ G2

Series

Operation Manual

CHN JPENG FR DE

CHN

JP

ENG

DE

FR

1-11

12-23

24-35

36-47

48-59

Register your new system and enjoy a free,

extended 1-year warranty on the aquarium

glass, in addition to the standard 2-year

system warranty*:

ENG

Operation Manual

This product is protected under Community Design 003003474, US Serial No 29/555,022 and Chinese Design Application. No. 201630060633.1

Red Sea REEFER™ G2 SERIES

Reef-Ready systems for advanced hobbyists

Red Sea REEFER™ Series

2

REEFER™ Operation Manual

Safety ...................................................................................4

Location ................................................................................5

Assembly ..............................................................................6

Overview of the REEFER™ water management system .......8

Operation .............................................................................9

Maintenance ............................................................ ..............10

Warranty ..............................................................................11

3

ENG

Congratulations on your purchase of the

Red Sea REEFER™ reef system.

Red Sea’s REEFER™ Systems provide advanced hobbyists with a solid

foundation for building a fully featured reef or marine aquarium. The

REEFER™ Series combines a contemporary, rimless, ultra-clear glass

aquarium with a stylish cabinet and a comprehensive water management

system, including a professional sump with integrated automatic top-up,

and Red Sea’s unique silent down-flow system.

Incorporating technologies originally developed for Red Sea’s all-in-

one MAX® coral reef systems, the REEFER™ series is designed for ease

of operation while enabling hobbyists to install an unlimited choice

of lighting, filtration, circulation and controllers to create a uniquely

customized system.

This manual complements the graphic assembly manuals and contains

installation and operational instructions for all of the REEFER™ series

aquariums.

We hope that you enjoy your REEFER™ and your reef.

To benefit from product update information and exclusive special offers to registered

REEFER™ owners, please register your REEFER™ on-line at redseafish.com

Red Sea REEFER™ Series

4

1 Safety

Please read and follow all safety instructions.

If the external cable Is damaged, It shall be replaced by the

manufacturer.

To avoid the possibility of the appliance plug or receptacle getting wet,

position the aquarium stand and tank to one side of a wall mounted

receptacle to prevent water from dripping onto the receptacle or plug.

You should create a “drip loop” (see Figure 1) for each cord connecting

an aquarium appliance to a receptacle. The “drip loop” is that part of the

cord below the level of the receptacle, or the connector. Use an extension

cord, if necessary, to prevent water traveling along the cord and coming

into contact with the receptacle. If the plug or receptacle does get wet,

DO NOT unplug the cord. Disconnect the fuse or circuit breaker that

supplies power to the appliance. Then unplug the device and examine for

presence of water in the receptacle.

Close supervision is necessary when any appliance is used by

or near children.

To avoid injury, do not contact moving parts.

Always unplug an appliance from an outlet when not in use, before

putting on or taking off parts, and before cleaning. Never pull the cord

itself to remove the plug from the outlet. Grasp the plug and pull to

disconnect.

Do not use an appliance for anything other than its intended use. The use

of attachments not recommended or sold by the appliance manufacturer

may cause an unsafe condition.

Do not install or store the appliance where it will be exposed to the

weather or to temperatures below freezing point.

Make sure an appliance mounted on a tank is securely installed before

operating it.

Read and observe all the important notices on the appliance.

NOTE: A cord rated for less amperes or watts than the appliance

rating may overheat. Care should be taken to arrange the cord

so that it cannot be tripped over or pulled accidental.

DANGER: To avoid possible electric shock, special care should be

taken when handling a wet aquarium. For each of the

following situations, do not attempt repairs yourself; return

the appliance to an authorized service facility for service or

discard the appliance.

WARNING: To guard against injury, basic safety precautions should be

observed, including the following:

Do not operate any appliance if it has a damaged cord or

plug, if it is malfunctioning, or if it is dropped or damaged

in any manner.

Drip Loop

figure 1

5

ENG

2 Location

The first step in setting up the REEFER™ is to choose a suitable location.

Weight

The flooring directly below the system must be rated to support the

following weight:

Approximate total weight of system including water

Model Nano 170 G2 200 G2 250 G2 300 G2 350 G2

Weight 180kg/

400lb

275Kg/

607lb

315kg/

695lb

380Kg/

840lb

470kg/

1035lb

530kg/

1170lb

Model 425 G2 525 G2 625 G2 750 G2 900 G2 P500 G2 P650 G2

Weight 690kg/

1520lb

850kg/

1875lb

930kg/

2060lb

1110kg/

2460lb

1300kg/

2870lb

760kg/

1680lb

940kg/

2080lb

Model S 850 G2 S 1000 G2

Weight 1210kg/

2675lb

1465kg/

3240lb

Room temperature

Site selection is important for correct temperature maintenance.

We recommended that you keep the ambient room temperature a

comfortable and stable 22°C / 72°F. Avoid placing the tank in front of

an air conditioner, heating vents or direct sunlight. A well ventilated

room with moderate light is the best place to position the aquarium.

Accessibility

Ensure that there is at least 10cm / 4” of clearance behind the

REEFER™ to allow easy access for installing/removing cables

from the sump as well as sufficient air circulation for a chiller

(larger models only). It is recommended to leave approximately

60cm/24” between one of the sides of the aquarium and any

adjacent walls or furniture for access to the rear of the tank.

General considerations

Ensure that the area surrounding the aquarium is waterproof and

consider moving away anything that water might damage or may be

corroded by the salt.

NOTE: The REEEFER™ system should not be moved when full of water.

Red Sea REEFER™ Series

6

3 Assembly

The following information complements the graphic manuals.

The REEFER™ includes the following main components:

• Glass aquarium

• Cabinet (self-assembly)

• Glass Sump including Bubble trap sponge, 225 micron filter bags/media

cups (according to model) and Float valve for automatic top-up

• Internal Piping kit with outlet nozzle

• Top-up reservoir (not included with REEFER 900 G2 & REEFER-S 850 G2

/1000 G2)

• Glass Extension Sump (REEFER 900 G2 and REEFER-S 850 G2 / 1000 G2

models only)

Detailed instructions for the complete assembly of the REEFER™ can be

found in the accompanying graphic manuals.

Complete the assembly of the cabinet including the doors as shown in the

graphic assembly manual and place in the final operating position (see

location above).

The top of the cabinet is approximately 86cm/34” ( 100cm/40” for

Peninsula ) from the floor.

The table shows the approximate weights of the different models of the

REEFER™ aquarium glass.

Approximate weight of Aquarium Glass

Model Nano 170 G2 200 G2 250 G2 300 G2 350 G2

Weight 25kg/

55lb

35Kg/

77lb

40kg/

88lb

55Kg/

122lb

58kg/

128lb

64kg/

140lb

Model 425 G2 525 G2 625 G2 750 G2 900 G2 P500 G2 P650 G2

Weight 95kg/

210lb

125kg/

275lb

155kg/

340lb

195kg/

430lb

225kg/

500lb

105kg/

230lb

170kg/

375lb

Model S 850 G2 S 1000 G2

Weight 226Kg/

500lb

258Kg/

570lb

Ensure that you have the correct number of people to lift the aquarium

according to its weight and size.

Ensure that anyone lifting the aquarium is physically suitable for such an

operation and has been instructed in the correct methods of lifting heavy

objects.

Once the aquarium is correctly aligned with the cabinet, check that the

cabinet has not moved. If necessary readjust the position of the cabinet.

For units with adjustable legs: Using a spirit level on the top surface of the

glass tank, adjust the height of the legs to level the aquarium. Make sure

that all legs are touching the floor.

WARNING: If you are not experienced in the construction of self-

assembly furniture or the installation of aquarium systems,

seek suitably qualified assistance.

ATTENTION: The top board of the cabinet (Part C) and some other parts

of the cabinet (in certain models) are packed under the

aquarium. In order to retrieve these parts, remove the

aquarium from its packaging. Make sure to avoid contact

between the Bulkheads on the bottom of the tank and the

floor, by placing the glass aquarium on Styrofoam parts that

are used in the package.

WARNING: Read before lifting the glass aquarium onto the cabinet.

NOTE: It is important to assemble the REEFER™ in the order indicated.

7

ENG

Before placing the glass sump in the cabinet make sure that the cabinet

doors are correctly aligned (see instructions in the cabinet assembly

manual). Once the sump is in position it will not be possible to make

adjustments to the lower hinge without moving the sump.

With the doors properly aligned, rotate the front section of the push

opener to the correct extension so that the doors will pop open when

pushed.

Overflow box pipes: Make sure that that the O-rings are in position on the

threaded connectors before assembly. To ensure correct assembly, firmly

hold the threaded connectors from inside the cabinet and tighten well by

hand. Do not use tools. Avoid unscrewing the pipes from the overflow box

once assembled as the locking mechanism that prevents counter-rotation

will be less effective.

Sump pipes: Make sure that that the O-rings are in position on the

connectors before assembly. After assembly check that the pipes are

vertical and the securing nut is holding the pipe in position. Do not use

tools and do not overtighten.

Overflow Box Cover: The overflow box cover reduces noise from the water

fall of the surface skimmer. If you wish to use the rear wall of the overflow

box for mounting equipment such as lighting, break out the section of the

cover as shown in the graphic manual. After breaking out the removable

section, smooth the remaining edge with a file or sandpaper.

NOTE: The REEFER™ aquarium system should not be moved when full

of water.

Red Sea REEFER™ Series

8

4 Overview of the REEFER™

water management system

Surface Skimmer / Overflow Box

Surface water from the aquarium flows via the removable comb sections

of the surface skimmer into the overflow box that houses the dual

intakes of the silent-flow downpipe system and the outlet nozzle of

the sump return pump. The silent-flow downpipe system includes a

flow-regulated main downpipe and a secondary overflow bypass pipe.

An external pipe with a clear upper section is placed over the main

downpipe to ensure positive water motion throughout the entire height

of the overflow box.

The fine adjustment flow valve on the main downpipe enables the water

level in the overflow box to be maintained at a constant height between

the intakes of the main and bypass pipes, which ensures positive surface

skimming while eliminating all noise from the water flow to the sump.

An incorrect setting of the flow valve will be accompanied by the sound

of the water returning to the sump and is an indication that the flow

valve needs adjusting.

Sump /ATO

Water from the flow-regulated main downpipe and the secondary

overflow bypass pipe enter a compact reception chamber in the sump.

Care should be taken in the choice of any filter media placed in the

reception chamber as the turbulent flow conditions from the downpipe

could cause a constant discharge of fine media particles.

The water then flows through the 400 micron filter before entering the

constant-height main reactor or skimmer chamber. If the filter bags are not

cleaned frequently enough and become blocked, the water will bypass the

filter bags without affecting the overall operation of the sump.

A bubble trap labyrinth with coarse foam separates the reactor chamber

from the pump compartment to prevent bubbles from the skimmer being

returned to the aquarium.

Any loss of water due to evaporation will cause a drop in the water level

in the pump compartment of the sump which will be compensated by

the ATO system.

Maintaining a constant water height in the pump compartment (with the

ATO) is essential for the stability of the entire water management system

by ensuring a constant head pressure on the intake of the main pump.

The reservoir contains water for approximately 3 days of evaporation and

should be kept topped up at all times.

9

ENG

Return Pump

The recommended flow rates for the return pumps are as shown in the

table below. The use of higher rated pumps will result in a higher water

level in the aquarium unless an appropriate modification is made to the

surface skimmer combs.

Recommended flow rate for return pumps

Model Nano 170 G2 200 G2 250 G2 300 G2

Flow 2000lph

/530gph

2000lph

/530gph

2000lph

/530gph

2500lph

/660gph

3000lph

/790gph

Model 350 G2 425 G2 525 G2 625 G2

Flow 3000lph

/790gph

4000lph

/1060gph

5000lph

/1325gph

6000lph

/1600gph

Model 750 G2 900 G2 P500 G2 P650 G2

Flow 7000lph

/1850gph

10000lph

/2640gph

6000lph

/1600gph

7000lph

/1850gph

Model S 850 G2 S 1000 G2

Flow 9,000lph/

2,385gph

10,000lph/

2650gph

5 Operation

Initial Fill

Check that all pipes are properly assembled and that any flexible tubes

are suitably secured in position.

Install any equipment that will take up water volume in the sump before

starting to fill the system.

Open the main flow valve (rotate anti-clockwise) to maximum.

Add approximately 15cm/6” of water to the overflow box to make sure

that all the pipe joins are watertight. Check for leaks inside the cabinet.

Add water to the main tank and once it is full, monitor the water level in

the sump as it begins to fill.

As soon as there is approximately 15cm/6” of water in the main pump

compartment switch on the pump and stop adding water.

Switch on skimmers or other filters that will affect the water level in the

sump and add more water as required to maintain the 15cm/6” of water

in the main pump compartment.

Allow the system to run for a few minutes and adjust the flow valve (as

described below) so that the water level in the overflow box is at the

correct level.

Add/remove water to/from the system and adjust the flow valve until

the water levels in the system stabilise.

WARNING: Overfilling the sump with equipment or water may cause

a flood in the event of an interruption of electric power.

Red Sea REEFER™ Series

10

Main downpipe valve adjustment

To raise the water level in the overflow box, rotate the valve clockwise.To

lower the water level in the overflow box, rotate the valve counter clockwise.

The main downpipe flow valve provides a very fine control of the flow

rate however after making adjustments it takes the system a few

minutes to stabilize at the new setting.

Once you have established the approximate setting for the valve make

very small adjustments and wait for a few minutes each time. It may

take a number of occasional adjustments to reach a stable level. When

set properly this system removes all of the noise of water flowing down

to the sump.

ATO

On initial set-up, wait until the saltwater system is stable before using

the ATO. Ensure that the top-up flow valve is fully closed.

Fill the top-up reservoir with RO water. Disconnect the top-up flow valve

from the float valve and slowly open the flow valve until the top-up

water drips at a rate of approximately 1 drop per second. Reconnect the

flow valve to the float valve.

Adjust the angle of the float so that the valve is closed when the water

level is above the inlet of the pump but below the top of the bubble trap.

Power-out test

After completing the initial set up and after adding any new equipment

to the sump, make any adjustments necessary to the main valve to

stabilise the system and perform a “power-out” test to check that water

does not rise above the rim of the sump.

6 Maintenance

For continuous smooth operation of the water management system make

regular checks of the following:

• Water level in the overflow box - adjust the flow valve as required

• Water level in the reservoir – top up with RO water as required

• Water level in the sump, check that the top-up float valve is

operating correctly

• Micron Filter Bags – check that water is flowing through the bags

and clean/replace as required

• Surface skimmer combs – remove any deposits that reduce water flow

• Pump outlet nozzle – check for blockages and build-up of algae

Micron Filter bags

It is recommended to have at least 3 sets of filter bags.

There are a few options for cleaning the filter bags:

Quick and effective – Spray the outside of the bags with a powerful

water jet such as a garden hose to back-flush the detritus from the

Polyester bag.

More thorough – soak the bags in bleach or diluted vinegar for 24 hours

prior to spraying as above. Rinse well to remove all chemicals before

returning to sump.

The filter bags can also be put in a cold wash in a washing machine with regular

detergent or with vinegar (may require approval from a higher authority).

NOTE: It is recommended to close the valve on the outlet of the

reservoir whenever doing maintenance in the sump

11

ENG

Warranty

Red Sea Aquarium Products Limited Warranty.

Thank you for purchasing a Red Sea Aquarium System (hereinafter “the

Product”).

Red Sea Aquatics (UK) Ltd. (hereinafter “Red Sea”) warrants the product

against manufacturer’s defects in material and workmanship for 24

months from your date of purchase. If you register your product, Red

Sea will provide you with an additional 12 months of warranty on the

glass aquarium only (but not on any other components of the Product).

In jurisdictions where warranty terms conditioned on registration are

prohibited by law, registration is not required, and you shall receive the

additional 12 months warranty on the glass aquarium even if you do not

register.

You can register your Product at www.redseafish.com

The warranty provided by Red Sea is NOT TRANSFERABLE AND IS

LIMITED TO THE ORIGINAL PURCHASER. If the Product is eligible under

this warranty, Red Sea will either repair the Product free of charge (not

including shipping costs) with new or refurbished parts or replace the

Product with a new or refurbished Product at Red Sea’s sole discretion.

This warranty DOES NOT COVER normal wear and tear, or items that

have a limited natural life or are consumable, such as, but not limited to

impellers, sponges, filter socks, and “O” rings. It also DOES NOT COVER

damage which occurs in shipment and/or failures or defects resulting

from use outside the normal, and/or natural disasters, accidents, power

line surges, neglect, improper installation, operation or maintenance,

servicing of the Product conducted by anyone other than an authorized

Red Sea service center, or failure to use or assemble the Product in

accordance with any instructions provided (in the Product manual or

otherwise) or the technical and/or safety standards of the country in

which the Product is used. Additionally, any modification of the Product

other than by an authorized Red Sea service center will invalidate this

warranty.

In order to effect this warranty, please contact your local service center.

For your convenience, details of authorized service centers can be found

on Red Sea’s website. Proof of purchase will be required before warranty

performance is rendered.

The sole and exclusive remedy against Red Sea shall be for the repair

or replacement of the Product as provided above. NO OTHER REMEDY

(including but not limited to, incidental or consequential damages for

lost profits, lost sales, or any other incidental or consequential loss) shall

be available. Some jurisdictions do not allow the exclusion of incidental

or consequential damage, so the above limitation may not apply to

you. To the full extent allowed by applicable law, in no event shall Red

Sea be liable for any loss or damage to aquatic life, and/or damage to

other property and/or individuals resulting from the use of the Product

or arising out of any breach of this warranty. All implied warranties are

excluded to the full extent allowed by applicable law, and to the extent

that they may not be excluded, are limited to the applicable warranty

period set forth above. Some jurisdictions do not allow limitations on how

long an implied warranty or condition lasts, so this limitation may not

apply to you. The express warranties made in this warranty are exclusive

and may not be altered, enlarged, or changed by any distributor, dealer,

or other person, whatsoever.

USA

Some states do not allow the exclusion or limitation of incidental or

consequential damages, or limitations on how long an implied warranty

lasts, so the above exclusion or limitations may not apply.

Red Sea REEFER™ Series

12

Registrieren Sie Ihr neues System und genießen

Sie zusätzlich zur standardmäßigen 2-Jahres-

Systemgarantie eine kostenlose, erweiterte

1-Jahres-Garantie auf das Aquarienglas*:

13

ENG

DE

Red Sea REEFER™ G2 SERIE

Innovative rahmenlose Riffsysteme für alle

anspruchsvollen Aquarianer

Dieses Produkt ist im Rahmen des gemeinschaftlichen Entwurfs 003003474, US-Serien-Nr. 29 / 555,022

und chinesischer Entwurfs-Anmeldung Nr. 201630060633.1 geschützt

Bedienungsanleitung

Red Sea REEFER™ Series

14

REEFER™ Bedienungshandbuch

Sicherheit .............................................................................16

Standort .................................................................. ..............17

Montage ...............................................................................18

Übersicht zum Wassermanagementsystem des REEFER™...20

Betrieb ..................................................................................21

Wartung ................................................................................22

Garantie .................................................................................23

15

ENG

DE

Herzlichen Glückwunsch zu Ihrem Kauf des

Red Sea REEFER™ Riffsystems.

Die Red Sea REEFER™ Aquariumserie bietet dem erfahrenen Aquarianer

eine solide Grundlage zum Aufbau eines Riff- oder Meerwasseraquariums.

Die REEFER™ Serie vereint ein zeitgemäßes, rahmenloses

Ultraklarglasaquarium mit einem eleganten Unterschrank und einem

umfassenden Wassermanagementsystem, welches ein professionelles

Technikbecken mit integrierter Nachfüllautomatik und den einzigartig

leisen Überlauf von Red Sea enthält.

Einschließlich der Technologien, die eigens für die “All-In-One” MAX®

Korallenriffsysteme von Red Sea entwickelt wurden, wurde die REEFER™

Serie für eine einfache Handhabung konzipiert, die es dem erfahrenen

Aquarianer ermöglicht, aus einer unbegrenzten Komponentenvielfalt

Beleuchtung, Filterung, Strömung und Steuerungseinheiten zu wählen und

sich so sein individuelles, einzigartiges System zusammen zu stellen.

Dieses Handbuch enthält Anleitungen zum Aufbau und Betrieb aller

Aquarien der Baureihe Red Sea REEFER™.

Wir hoffen, dass Sie an Ihrem REEFER™ viel Freude haben.

Um in den Genuss von Informationen zu Produkt-Updates und exklusiven

Sonderangeboten für registrierte REEFER™-Besitzer zu kommen, registrieren Sie

bitte Ihr REEFER™ online unter redseafish.com

Red Sea REEFER™ Series

16

1 Sicherheit

Bitte lesen und befolgen Sie alle hier aufgeführten Sicherheitshinweise.

Um ein Nasswerden des Gerätesteckers oder der Steckdose zu

vermeiden, stellen Sie Gestell und Becken des Aquariums neben einer

Wandsteckdose so auf, dass kein Wasser auf die Steckdose oder den

Netzstecker tropfen kann. Der Benutzer sollte eine „Tropfschleife“

(Abbildung 1) für jedes Netzkabel bilden, das ein Gerät des Aquariums

mit der Steckdose verbindet. Die „Tropfschleife“ ist der Teil des

Netzkabels, der unterhalb der Steckdose oder der Anschlussdose liegt.

Vermeiden Sie wenn möglich ein Verlängerungskabel, um zu vermeiden,

dass Wasser am Kabel entlangläuft und mit der Steckdose in Berührung

kommt. Wenn der Stecker oder die Steckdose nass wird, Netzkabel

NICHT aus der Steckdose ziehen. Schalten Sie die Sicherung oder den

Sicherungsschalter des Stromkreises für das Gerät aus. Ziehen Sie

erst danach das Netzkabel des Gerätes heraus und überprüfen Sie die

Steckdose auf das Vorhandensein von Wasser.

Wenn das Gerät von Kindern oder in der Nähe von Kindern benutzt

wird, müssen diese gut beaufsichtigt werden. Zur Vermeidung von

Verletzungen keine Teile berühren, die sich in Bewegung befinden.

Ziehen Sie immer den Netzstecker eines Gerätes, wenn dieses nicht

in Gebrauch ist, bevor Sie Teile anbringen oder entfernen und vor

dem Reinigen. Ziehen Sie nie am Netzkabel, um den Netzstecker aus

der Steckdose zu lösen. Fassen Sie den Netzstecker an und ziehen sie

ihn heraus. Benutzen Sie ein Gerät immer nur für den vorgesehenen

Verwendungszweck. Die Verwendung von Anbauteilen, die nicht vom

Gerätehersteller empfohlen oder verkauft werden, kann zu einem

unsicheren Betriebszustand führen. Installieren oder lagern Sie das

Gerät nicht dort, wo es der Witterung oder Temperaturen unter dem

Gefrierpunkt ausgesetzt ist. Vergewissern Sie sich, dass ein an ein Becken

montiertes Gerät sicher installiert ist, bevor Sie es in Betrieb nehmen.

Lesen und befolgen Sie alle wichtigen Hinweise auf dem Gerät.

HINWEIS: Ein Kabel, das für eine geringere Ampere- oder Wattzahl als

die des Gerätes ausgelegt ist, kann sich überhitzen. Achten

Sie darauf, dass das Kabel so verlegt wird, dass man nicht

darüber stolpern oder es versehentlich herausziehen kann.

GEFAHR: Zur Vermeidung von Stromschlägen sollten Sie beim Umgang

mit einem nassen Aquarium besonders vorsichtig sein.

Versuchen Sie in keiner der im Folgenden beschriebenen

Situationen Reparaturen selber durchzuführen, sondern

geben Sie elektronische Komponenten zur Reparatur an eine

autorisierte Kundendienststelle oder entsorgen Sie das Gerät.

WARNUNG: Zum Schutz vor Verletzungen sollten grundlegende

Sicherheitsvorkehrungen beachtet werden,

einschließlich der folgenden Hinweise:

Betreiben Sie kein Gerät mit beschädigtem Netzkabel

oder ein Gerät, das nicht ordnungsgemäß funktioniert,

heruntergefallen ist oder anderweitig beschädigt ist.

Tropfschleife

Abbildung 1

ページが読み込まれています...

Red Sea REEFER 300 G2 取扱説明書

Red Sea REEFER 300 G2 取扱説明書

他の言語で

関連論文

その他のドキュメント