Dell Supported Configurations for Oracle Database 10g R2 for Windows ユーザーガイド

Dell PowerEdge Systems

Oracle Database on Microsoft

Windows Server x64

Storage and Network

Guide

Version 4.4

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data if

instructions are not followed.

WARNING: A WARNING indicates a potential for property damage, personal

____________________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, EqualLogic™, PowerEdge™, and PowerVault™

are trademarks of Dell Inc.; EMC

®

and PowerPath

®

are registered trademarks of EMC Corporation;

Intel

®

is a registered trademark of Intel Corporation in the U.S. and other countries; Microsoft

®

,

Windows

®

and Windows Server

®

are either trademarks or registered trademarks of Microsoft

Corporation in the US and/or other countries; Oracle

®

is a registered trademark of Oracle Corporation

in the US and/or other countries.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

July 2010 Rev. A03

Contents 3

Contents

1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Required Documentation for Deploying the

Dell Oracle Database

. . . . . . . . . . . . . . . . . . . 7

Terminology Used in This Document

. . . . . . . . . . . 8

Getting Help

. . . . . . . . . . . . . . . . . . . . . . . . 9

Dell Support. . . . . . . . . . . . . . . . . . . . . . 9

Oracle Support . . . . . . . . . . . . . . . . . . . . 9

2 Fibre Channel Cluster Setup . . . . . . . . . . 11

Cabling Your Dell/EMC Fibre Channel Storage . . . . . 13

3 SAS Cluster Setup for the

Dell PowerVault MD3000 . . . . . . . . . . . . 15

Cabling Your SAS Storage System. . . . . . . . . . . . 17

4 iSCSI Cluster Setup for the Dell

PowerVault MD3000i and PowerVault

MD1000 Expansion Enclosures . . . . . . . . 19

Setting Up iSCSI Cluster With Dell PowerVault

MD3000i Storage System and Dell PowerVault

MD1000 Expansion Enclosures

. . . . . . . . . . . . . 21

Cabling Your iSCSI Storage System . . . . . . . . 21

4 Contents

5 iSCSI Cluster Setup for the

Dell EqualLogic PS Series

Storage Systems . . . . . . . . . . . . . . . . . . . 25

Cabling Dell EqualLogic iSCSI Storage System . . . . . 25

6 Configuring Network and Storage

for Oracle RAC Database . . . . . . . . . . . . 29

Configuring the Public and Private Networks. . . . . . 29

Configuring and Teaming the Private Network . . . 30

Configuring NIC Teaming for Your Private

Network Adapters . . . . . . . . . . . . . . . . . 31

Configuring the IP Addresses for Your

Public and Private Network Adapters . . . . . . . 33

Installing the Host-Based Software

Required for Storage

. . . . . . . . . . . . . . . . . . . 36

Installing Multi-Path Software for Storage

. . . . . . . 36

Installing EMC PowerPath for

Dell/EMC Systems. . . . . . . . . . . . . . . . . . 36

Installing Multi-Path Driver Software for

PowerVault MD3000 or PowerVault MD3000i . . . 37

Installing Multi-Path Driver Software for

EqualLogic iSCSI Storage Array . . . . . . . . . . 37

Verifying Multi-Path Driver Functionality . . . . . . 37

Verifying and Upgrading the Firmware . . . . . . . . . 37

Configuring Your EqualLogic iSCSI Storage

. . . . . . . 38

Creating Volumes . . . . . . . . . . . . . . . . . . 38

Configuring iSCSI Networks . . . . . . . . . . . . 39

Configuring Host Access to Volumes . . . . . . . . 39

Configuring Microsoft iSCSI Initiator . . . . . . . . 40

Contents 5

Verifying the Storage Assignment to the Nodes . . . . 41

Preparing the Disks for Oracle Clusterware,

Database, and Backup

. . . . . . . . . . . . . . . . . . 42

Enabling the Automount Option for

the Shared Disks . . . . . . . . . . . . . . . . . . 43

Preparing the OCR and Voting Disks for

Clusterware on Windows Server 2003 . . . . . . . 43

Preparing the OCR and Votingdisk for

Clusterware on Windows Server 2008 . . . . . . . 45

Preparing the Database Disk and

Flash Recovery Area for Database

Storage With OCFS . . . . . . . . . . . . . . . . . 46

Preparing the Database Disk and

Flash Recovery Area for Database

Storage With ASM . . . . . . . . . . . . . . . . . 47

7 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

6 Contents

Overview 7

Overview

The Storage and Networking Guide for Oracle Database on

Microsoft Windows applies to:

• Oracle Database 10g R2 Enterprise Edition on Microsoft Windows Server

2003 R2 Standard or Enterprise x64 Edition or Windows Server 2008 SP2

Enterprise or Standard x64 Edition.

• Oracle Database 10g R2 Standard Edition on Windows Server 2003 R2

SP2 Standard x64 Edition or Windows Server 2008 SP2 Standard

x64

Edition.

Required Documentation for Deploying the

Dell

Oracle Database

The documents required for installing the Dell|Oracle database are:

•

Oracle Database on Microsoft Windows Server x64 Operating System and

Hardware Installation Guide

—Describes the required minimum hardware

and software versions, how to install and configure the operating system,

how to verify the hardware and software configurations, and how to obtain

open source files.

•

Oracle Database on Microsoft Windows Server x64 Storage and Network

Guide

—Describes how to install and configure the network and the

storage solutions.

•

Oracle Database on Microsoft Windows Server x64 Database Setup and

Installation Guide

—Describes how to install and configure the

Oracle

database.

•

Oracle Database on Microsoft Windows Server x64 Troubleshooting

Guide

—Describes how to troubleshoot and resolve errors encountered

during the installation procedures described in the previous

modules.

NOTE: All modules provide information on how to receive technical assistance

from Dell.

8 Overview

Terminology Used in This Document

This document uses the terms logical unit number (LUN) and virtual disk.

These terms are synonymous and can be used interchangeably. The term

LUN is commonly used in a Dell/EMC Fibre Channel storage system

environment and virtual disk is commonly used in a Dell PowerVault SAS

or iSCSI (Dell PowerVault MD3000 and Dell PowerVault MD3000i with

Dell PowerVault MD1000 expansion) storage environment.

Dell EqualLogic PS series storage arrays include storage virtualization

technology. To better understand how these arrays operate, it is helpful to be

familiar with some of the terminologies used to describe these arrays and

their functions:

•

Member

—A single PS series array.

•

Group

—A set of one or more members that can be centrally managed.

Host servers access the data through a single group IP address.

•

Pool

—A RAID that can consist of the disks from one or more members.

•

Volume

—A LUN or virtual disk that represents a subset of the capacity of

a pool.

Overview 9

Getting Help

This section provides information on contacting Dell or Oracle for

whitepapers, supported configurations, training, technical support,

and general information.

Dell Support

• For detailed information about using your system, see the documentation

that came with your system components.

• For whitepapers, Dell-supported configurations, and general information,

see

dell.com/oracle

.

• For Dell technical support for your hardware and operating system

software and to download the latest updates for your system, see

support.dell.com

. Information about contacting Dell is provided in the

Dell PowerEdge Systems Oracle Database on Microsoft Windows Server x64

Operating System and Hardware Installation Guide

and

Dell PowerEdge

Systems Oracle Database on Microsoft Windows Server x64 Troubleshooting

Guide

of your system.

• Dell Enterprise Training and Certification is now available;

see

dell.com/training

for more information. This training service may

not

be offered in all locations.

Oracle Support

• For training information on your Oracle software and application

clusterware, and for information about contacting Oracle, see

oracle.com

or see your Oracle documentation.

• Technical support, downloads, and other technical information is available

at

metalink.oracle.com

.

10 Overview

Fibre Channel Cluster Setup 11

Fibre Channel Cluster Setup

WARNING: Before you begin any of the procedures in this section, read the

safety information that shipped with your system. For additional best practices

information, see dell.com/regulatory_compliance.

After a Dell Managed Services representative completes the setup of your

Fibre Channel cluster, verify the hardware connections and the hardware and

software configurations as described in this section. Figure 2-1 and Figure 2-2

show an overview of the connections required for the cluster and Table 2-1

summarizes the cluster connections.

Figure 2-1. Hardware Connections for a SAN-Attached Fibre Channel Cluster

Client Systems

Gigabit Ethernet Switches (Private Network)

Dell PowerEdge Systems

(Oracle Database)

CAT 5e/6 (Public NIC)

CAT 5e/6 (Copper Gigabit NIC)

Fiber Optic Cables

Dell/EMC Fibre Channel

Storage Systems

Dell/EMC Fibre Channel

Switches (SAN)

LAN/W AN

Additional Fiber Optic Cables

12 Fibre Channel Cluster Setup

Table 2-1. Fibre Channel Hardware Interconnections

Cluster Component Connections

Dell PowerEdge

system node

• One Category 5 enhanced (CAT 5e) or CAT 6 cable from the

public NIC to

the LAN

• One CAT 5e or CAT 6 cable from the private Gigabit NIC to

the Gigabit Ethernet switch

• One CAT 5e or CAT 6 cable from a redundant private

Gigabit

NIC to a redundant Gigabit Ethernet switch

• One fiber optic cable from HBA 0 to Fibre Channel switch 0

• One fiber optic cable from HBA 1 to Fibre Channel switch 1

Dell/EMC Fibre

Channel storage

system

• Two CAT 5e or CAT 6 cables connected to the LAN

• One to four fiber optic cable connections to each Fibre

Channel switch. For

example, for a four-port configuration:

–One

fiber optic cable

from SPA port 0 to Fibre Channel

switch 0

–One

fiber optic cable

from SPA port 1 to Fibre Channel

switch 1

–One

fiber optic cable

from SPB port 0 to Fibre Channel

switch 1

•One

fiber optic cable

from SPB port 1 to Fibre Channel switch 0

Dell/EMC Fibre

Channel switch

• One to four fiber optic cable connections to the

Dell/EMC

Fibre Channel storage system

• One fiber optic cable connection to each PowerEdge

system

HBA

Gigabit Ethernet

switch

• One CAT 5e or CAT 6 connection to the private Gigabit NIC

on each PowerEdge system

• One CAT 5e or CAT 6 connection to the remaining Gigabit

Ethernet switch

Fibre Channel Cluster Setup 13

Cabling Your Dell/EMC Fibre Channel Storage

You can configure your Oracle cluster storage system in a four-port storage

area network (SAN) attached configuration, depending on your needs.

See the following procedures for both configurations.

Figure 2-2 illustrates the hardware connections used in setting up a

SAN-attached Fibre Channel cluster.

Figure 2-2. Cabling in a Dell/EMC SAN-Attached Fibre Channer Cluster

Two HBA Ports for Node 1

Two HBA Ports for Node 2

sw1

Dell/EMC CX4-480 Fibre Channel Storage

sw0

SP-B

SP-A

14 Fibre Channel Cluster Setup

To configure your Oracle cluster storage system in a four-port, SAN-attached

configuration (see Figure 2-2):

1

Connect one optical cable from SP-A port 0 to Fibre Channel switch 0.

2

Connect one optical cable from SP-A port 1 to Fibre Channel switch 1.

3

Connect one optical cable from SP-B port 0 to Fibre Channel switch 1.

4

Connect one optical cable from SP-B port 1 to Fibre Channel switch 0.

5

Connect one optical cable from HBA 0 on node 1 to

Fibre

Channel switch 0.

6

Connect one optical cable from HBA 1 on node 1 to

Fibre

Channel switch 1.

7

Connect one optical cable from HBA 0 of each additional node to

Fibre

Channel switch 0.

8

Connect one optical cable from HBA 1 of each additional node to

Fibre

Channel switch 1.

SAS Cluster Setup for the Dell PowerVault MD3000 15

SAS Cluster Setup for the

Dell

PowerVault MD3000

WARNING: Before you begin any of the procedures in this section, read the

safety information that shipped with your system. For additional best practices

information, see dell.com/regulatory_compliance.

This section provides information and procedures to configure your

Dell PowerEdge systems and PowerVault MD3000 hardware and software

to function in an Oracle Real Application Cluster (RAC) environment.

Verify the hardware connections, and the hardware and software

configurations as described in this section using Figure 3-1, Table 3-1,

and Table 3-2.

Figure 3-1. Cabling the Serial-Attached SCSI (SAS) Cluster and

Dell

PowerVault MD3000

Public Network

LAN/WAN

PowerEdge Systems

PowerVault MD3000

Storage System

CAT 5e/6 (Copper Gigabit NIC)

SAS Cables

16 SAS Cluster Setup for the Dell PowerVault MD3000

Table 3-1. SAS Cluster Hardware Interconnections

Cluster Component Connections

PowerEdge system node

• One CAT 5e/6 cable from public NIC to the local

area network (LAN).

• One CAT 5e/6 cable from private Gigabit NIC to

Gigabit Ethernet switch (private network).

• One CAT 5e/6 cable from redundant private Gigabit

NIC to redundant Gigabit Ethernet switch

(private

network).

• Two SAS connections to a PowerVault MD3000

storage system node using a SAS 5/E. See

“Cabling

Your SAS Storage System” on page 17.

PowerVault MD3000

• Two CAT 5e/6 cables connected to a LAN (one from

each storage processor module).

• Two SAS connections to each PowerEdge system

node using a SAS 5/E controller. See

“Cabling Your

SAS Storage System” on page 17.

Gigabit Ethernet switch

• One CAT 5e/6 connection to the private Gigabit

NIC on each PowerEdge system.

• One CAT 5e/6 connection to the other Gigabit

Ethernet switch.

SAS Cluster Setup for the Dell PowerVault MD3000 17

Cabling Your SAS Storage System

SAS clusters can only be installed in a direct-attached cluster and are limited

to two nodes only.

To configure your nodes in a direct-attached configuration (see Figure 3-2):

1

Connect one SAS cable from a port of the SAS controller of node 1 to the

In-0 port of RAID controller 0 in the PowerVault MD3000 RAID enclosure.

2

Connect one SAS cable from a port of the other SAS controller of node 1

to the In-0 port of RAID controller 1 in the PowerVault MD3000 RAID

enclosure.

3

Connect one SAS cable from a port of the SAS controller of node 2 to the

In-1 port of RAID controller 0 in the PowerVault MD3000 RAID enclosure.

4

Connect one SAS cable from a port of the other SAS controller of node 2

to the In-1 port of RAID controller 1 in the PowerVault MD3000 RAID

enclosure.

Figure 3-2. Cabling in a Direct-Attached SAS Cluster

Dual-HBA Host Server

RAID Controller Module 1

PowerVault MD3000 RAID

Enclosure

MD1000 Expansion Enclosure

RAID Controller Module 0

18 SAS Cluster Setup for the Dell PowerVault MD3000

iSCSI Cluster Setup 19

iSCSI Cluster Setup for the

Dell

PowerVault MD3000i

and

PowerVault MD1000

Expansion

Enclosures

WARNING: Before you begin any of the procedures in this section, read the

safety information that shipped with your system. For additional best practices

information, see dell.com/regulatory_compliance.

This section provides information and procedures to configure your

Dell PowerEdge systems and Dell PowerVault MD3000i hardware

and software to function in an Oracle Real Application Cluster (RAC)

environment.

Verify the hardware connections, and the hardware and software

configurations, using the Supported Configuration figures contained in the

Dell PowerVault MD3000i Support Matrix available at support.dell.com.

Table 4-1. iSCSI Hardware Interconnections

Cluster Component Connections

One PowerEdge

system

node

• One CAT 5e/6 cable from public NIC to the local area

network (LAN).

• One CAT 5e/6 cable from private Gigabit NIC to Gigabit

Ethernet switch (private network).

• One CAT 5e/6 cable from redundant private Gigabit NIC

to redundant Gigabit Ethernet switch (private network).

NOTE: For additional information on Dell PowerVault

MD3000i system see your Dell PowerVault MD3000i SetUp

documentation.

20 iSCSI Cluster Setup

One Dell PowerVault

MD3000i storage

system

• Two CAT 5e/6 cables connected to LAN (one from each

storage processor module) for the management interface.

• Two CAT 5e/6 cables per storage processor for iSCSI

interconnect.

NOTE: For additional information on Dell PowerVault

MD3000i system see your Dell PowerVault MD3000i Setup

documentation.

One Dell PowerVault

MD1000 storage

expansion enclosure

(optional)

Additional Serial-attached SCSI (SAS) cable connections

as required for the MD1000 expansion enclosures.

Table 4-1. iSCSI Hardware Interconnections

Cluster Component Connections

ページが読み込まれています...

Dell Supported Configurations for Oracle Database 10g R2 for Windows ユーザーガイド

Dell Supported Configurations for Oracle Database 10g R2 for Windows ユーザーガイド

他の言語で

関連論文

その他のドキュメント