Dell Supported Configurations for Oracle Database 10g R2 for Windows ユーザーガイド

Dell PowerEdge Systems

Oracle Database on Microsoft

Windows Server x64

Operating System and

Hardware Installation

Guide

Version 4.4

Notes and Cautions

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data if

instructions are not followed.

____________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, PowerEdge™, and PowerVault™ are trademarks

of Dell Inc. Intel

®

, and Xeon

®

are registered trademarks of Intel Corporation in the U.S. and other

countries. AMD

®

, the AMD logo, and combinations thereof, are registered trademarks and AMD

Opteron™ is a trademark of Advanced Micro Devices, Inc. Microsoft

®

, Windows

®

, and Windows

Server

®

are either trademarks or registered trademarks of Microsoft Corporation in the United States

and/or other countries. Oracle

®

is a registered trademark of Oracle Corporation and/or its affiliates.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

July 2010 Rev. A03

Contents 3

Contents

1 Overview of Oracle Database

Installation on Microsoft

Windows Server x64 . . . . . . . . . . . . . . . . . 5

Required Documentation for Deploying

the Dell|Oracle Database

. . . . . . . . . . . . . . . . . 5

Terminology Used in This Document

. . . . . . . . . . . 6

Getting Help

. . . . . . . . . . . . . . . . . . . . . . . . 6

Dell Support. . . . . . . . . . . . . . . . . . . . . . 6

Oracle Support . . . . . . . . . . . . . . . . . . . . 6

2 Software and Hardware Requirements. . . 7

Minimum Software Requirements . . . . . . . . . . . . 7

Minimum Hardware Requirements . . . . . . . . . . . . 8

3 Installing and Configuring

the Operating System . . . . . . . . . . . . . . . 13

Before You Begin . . . . . . . . . . . . . . . . . . . . 13

Installing the Operating System Using

the Dell Systems Management Tools

and Documentation DVD

. . . . . . . . . . . . . . . . . 14

4 Contents

Continuing With the Operating System Installation . . . 16

Installing Windows Server 2003 . . . . . . . . . . 16

Installing Windows Server 2008 SP2 . . . . . . . . 17

Installing the Resource CD . . . . . . . . . . . . . 18

Installing the Driver for a Qlogic

Fibre Channel HBA . . . . . . . . . . . . . . . . . 19

Verifying the Temporary Directory Paths . . . . . . 20

4 Verifying Cluster Hardware

and Software Configurations . . . . . . . . . 23

Overview of Oracle Database Installation on Microsoft Windows Server x64 5

Overview of Oracle Database

Installation on Microsoft Windows

Server x64

This document applies to:

• Oracle Database 10g R2 Enterprise Edition on Windows Server 2003 R2

SP2 Enterprise/Standard x64 Edition or Windows Server 2008 SP2

Enterprise/Standard x64 Edition.

• Oracle Database 10g R2 Standard Edition on Windows Server 2003 R2

SP2 Standard x64 Edition or Windows Server 2008 SP2 Standard x64

Edition.

Required Documentation for Deploying the

Dell|Oracle Database

The documentation set for the Oracle Database on Microsoft Windows is

organized into a series of modules. These modules cover the following topics:

•

Oracle Database on Microsoft Windows Server x64 Operating System and

Hardware Installation Guide

—Describes the required minimum hardware

and software versions, how to install and configure the operating system,

how to verify the hardware and software configurations, and how to obtain

open source files.

•

Oracle Database on Microsoft Windows Server x64 Storage and Networking

Guide

—Describes how to install and configure the network and the

storage solutions.

•

Oracle Database on Microsoft Windows Server x64 Database Setup and

Installation Guide

—Describes how to install and configure the

Oracle

Database.

•

Oracle Database on Microsoft Windows Server x64 Troubleshooting Guide

—

Describes how to troubleshoot and resolve errors encountered during the

installation procedures described in the previous modules.

6 Overview of Oracle Database Installation on Microsoft Windows Server x64

Terminology Used in This Document

This document uses the terms logical unit number (LUN), virtual disk, and

volumes. These terms are synonymous and can be used interchangeably.

The term LUN is commonly used in a Dell|EMC Fibre Channel storage

system environment, virtual disk is commonly used in a direct-attached

SAS (Dell MD3000/MD3000i and Dell MD3000/MD3000i with MD1000

expansion) storage environment and volume is commonly used in a

Dell EqualLogic iSCSI storage system environment.

Getting Help

Dell Support

For detailed information about using your system, see the documentation

that came with your system components.

For whitepapers, Dell-supported configurations, and general information,

visit dell.com/oracle.

For Dell technical support for your hardware and operating system software

and to download the latest updates for your system, visit support.dell.com.

NOTE: Information about contacting Dell is provided in your system’s Oracle

Database on Microsoft Windows Server x64 Operating System and Hardware

Installation Guide.

Dell Enterprise Training and Certification is now available;

see dell.com/training for more information. The training service may not

be offered in all locations.

Oracle Support

For information about Oracle software, application clusterware training,

and contacting Oracle, see oracle.com or your Oracle documentation that

shipped with the system components. For information on technical support,

downloads, and other technical information, see metalink.oracle.com.

For information on configuring storage and networking, see the

Oracle

Database on Microsoft Windows Server x64

Storage and Networking Guide.

Software and Hardware Requirements 7

Software and Hardware

Requirements

Minimum Software Requirements

Table 2-1 lists the minimum software requirements and supported

configurations for Oracle Database on Microsoft Windows Server x64 Editions.

NOTE: Your Dell configuration includes a 30-day trial license of Oracle software.

If

you do not have a license for this product, contact your Dell sales representative.

Table 2-1. Software Requirements for Oracle Database on Windows Server x64

Editions

Oracle

Database

(x64) Edition

Oracle Configuration Microsoft Windows

(x64) Edition

EMC PowerPath (Fibre

Channel Clusters Only)

Oracle Database 10g R2

10g R2

Enterprise

Edition

Release 10.2.0.1,

including RAC

option + 10.2.0.4

Patch Set

Server 2003 R2 SP2

Enterprise/Standard

Edition

Version 5.3

10g R2

Standard

Edition

Release 10.2.0.1,

including RAC

option + 10.2.0.4

Patch Set

Server 2003 R2 SP2

Standard Edition

Version 5.3

10g R2

Enterprise

Edition

Release 10.2.0.4

including RAC

option

Server 2008 SP2

Enterprise/Standard

Edition

Version 5.3

10g R2

Standard

Edition

Release 10.2.0.4

including RAC

option

Server 2008 SP2

Standard Edition

Version 5.3

8 Software and Hardware Requirements

Minimum Hardware Requirements

Table 2-2 lists the minimum hardware requirements for Oracle Database 10g

Enterprise Edition on Microsoft Windows Server 2003 R2 SP2 or Windows

Server 2008 SP2 Standard/Enterprise x64 Editions. For more information on

specific hardware components, see the documentation included with your

system.

NOTE: To achieve the desired performance, choose a system that exceeds the

minimum hardware requirements based on the number of users, the applications

you use, and batch processes.

NOTE: The hardware configuration of all the cluster nodes should be identical.

Table 2-2. Oracle Database 10g Enterprise Edition on Microsoft Windows Server 2003

R2 SP2 or Windows Server 2008 SP2 Standard/Enterprise x64 Editions

Minimum Hardware Requirements

Hardware Component Configuration

Dell PowerEdge 1950 IIII, 2900 III, 2950 II,

T610, T710, R610, R710, R810,R900,

R910, M600, M610, M710, and M910

systems (up to eight nodes using

Automatic Storage Management (ASM)

or Oracle Cluster File System (OCFS)).

• Intel Xeon processor family.

• 1 GB of RAM.

• PERC for internal hard drives.

• Two 73-GB hard drives connected to

a PERC controller.

NOTE: It is recommended that you use

two 73-GB hard drives (RAID 1) connected

to an internal RAID controller. See your

PowerEdge system documentation for

more details.

• Three Gigabit NICs.

• Two HBAs

(1 QLE2462/QLE2562 [dual port]

HBA for use with PowerEdge

1950/R610.

• One QME2472/QME2572 or

LPe1105-M4/LPe1205 [dual port]

HBA for use with PowerEdge

M600/M610/M710).

Software and Hardware Requirements 9

Dell PowerEdge 6950, 2970, M605, R805,

R815, and R905 systems (up to eight nodes

using ASM or OCFS).

• AMD Opteron processor family.

• 1 GB of RAM.

• Two 73-GB hard drives connected to

an internal RAID controller.

NOTE: It is recommended that you use

two 73-GB hard drives (RAID 1) connected

to an internal RAID controller based on

your system. See your PowerEdge system

documentation for more details.

• Three Gigabit NICs.

• Two HBAs for use with PowerEdge

6950 or 2970.

• One QME2472/QME2572 or

LPe1105-M4/LPe1205 [dual port]

HBA for use with PowerEdge

M605/M805/M905.

Gigabit Ethernet switches (two) See dell.com/oracle for information on

supported configurations.

For Dell|EMC AX4-5F, CX3-10C, CX3-20,

CX3-20F, CX3-40, CX3-40F, CX3-80,

CX4-120, CX4-240, CX4-480, and

CX4-960 Fibre Channel storage systems.

See the Dell|EMC system

documentation for more details.

For direct-attached SAS

Dell PowerVault MD3000 with MD1000

expansion storage system.

See your Dell PowerVault MD3000 and

MD1000 storage system documentation

for more details.

For direct-attached or switched iSCSI

Dell PowerVault MD3000i with MD1000

expansion storage system.

See your Dell PowerVault MD3000i and

MD1000 storage system documentation

for more details.

Dell EqualLogic PS Series Storage. One Dell EqualLogic PS Series array

with sixteen 15,000 RPM SAS disks.

Two Gigabit Ethernet switches for

iSCSI SAN.

Table 2-2. Oracle Database 10g Enterprise Edition on Microsoft Windows Server 2003

R2 SP2 or Windows Server 2008 SP2 Standard/Enterprise x64 Editions

Minimum Hardware Requirements (continued)

Hardware Component Configuration

10 Software and Hardware Requirements

Table 2-3 lists the minimum hardware requirements for Oracle Database 10g

Standard Edition on Microsoft Windows Server 2003 R2 SP2 or Windows

Server 2008 SP2 Standard x64 Editions. For more information on specific

hardware components, see the documentation included with your system.

Table 2-3. Oracle Database 10g Standard Edition on Microsoft Windows Server 2003 R2

SP2 or Windows Server 2008 SP2 Standard x64 Editions Minimum Hardware

Requirements

Hardware Component Configuration

Dell PowerEdge 1950 III, 2950 III,

2900III, T610, T710, R610, and R710

systems (up to two nodes using ASM).

• Intel Xeon processor family.

• 1 GB of RAM.

• PERC for internal hard drives.

• Two 73-GB hard drives connected to a

PERC controller.

NOTE: It is recommended that you use two

73-GB hard drives (RAID 1) connected to

an internal RAID controller based on

your system. See your PowerEdge system

documentation for more details.

• Three Gigabit NICs.

• Two HBAs.

• One QLE2462/QLE2562 [dual port]

HBA for use with PowerEdge

1950/R610.

Dell PowerEdge 2970, R805 systems

(up to two nodes using ASM)

• AMD Opteron processor family.

• 1 GB of RAM.

• Two 73-GB hard drives connected to an

internal RAID controller.

NOTE: It is recommended that you use two

73-GB hard drives (RAID 1) connected to

an internal RAID controller based on

your system. See your PowerEdge system

documentation for more details.

• Three Gigabit NICs.

Software and Hardware Requirements 11

Gigabit Ethernet switches (two). See dell.com/oracle for information on

supported configurations.

For Dell|EMC AX4-5F, CX3-10C, CX3-

20, CX3-20F, CX3-40, CX3-40F, CX3-80,

CX4-120, CX4-240, CX4-480, and CX4-

960 Fibre Channel storage systems.

See the Dell|EMC system

documentation for more details.

For direct-attached SAS Dell PowerVault

MD3000 with MD1000 expansion

storage system.

See your Dell PowerVault MD3000 and

MD1000 storage system documentation

for more details.

For direct-attached or switched Dell

PowerVault MD3000i with MD1000

expansion storage system.

See your Dell PowerVault MD3000i and

MD1000 storage system documentation

for more details.

Table 2-3. Oracle Database 10g Standard Edition on Microsoft Windows Server 2003 R2

SP2 or Windows Server 2008 SP2 Standard x64 Editions Minimum Hardware

Requirements (continued)

Hardware Component Configuration

12 Software and Hardware Requirements

Installing and Configuring the Operating System 13

Installing and Configuring the

Operating System

CAUTION: To ensure that the operating system is installed correctly, disconnect

all external storage from the system before you install the operating system.

This section provides information about installing and configuring the

Microsoft Windows Server 2003 R2 SP2 and Windows Server 2008 SP2

Standard/Enterprise x64 Edition operating system for

Oracle database deployment.

Before You Begin

NOTE: See support.dell.com for the latest BIOS, firmware, and driver updates.

1

Shut down your system.

2

Disconnect all external storage devices from your system.

3

Locate the correct

Microsoft Windows Server 2003 R2 SP2

or

Windows Server 2008 SP2 Standard/Enterprise x64 Edition

media

and the

Dell Systems Management Tools and Documentation

media

for your Dell Server using the information in Table 3-1.

Table 3-1. PowerEdge Server Systems Management Media

Dell PowerEdge System Systems Management Media

6950, 1950, 2900, 2950, 2970, 1950 III,

2900 III, 2950 III, R805, R905, R900,

M600, M605, M610, M710, M805,

M905, T610, T710, R610, and R710.

Dell Systems Management Tools and

Documentation media version 6.2.

R810, R815, R910, and M910. Dell Systems Management Tools and

Documentation media version 6.2.1

NOTE: The Dell Systems Management Tools and Documentation media is packaged with

your Dell server.

14 Installing and Configuring the Operating System

Installing the Operating System Using the

Dell

Systems Management Tools and

Documentation DVD

1

Turn on your system.

2

Insert the

Dell Systems Management

media for your system in your system

drive.

The Dell Systems Build and Update Utility Welcome

window is displayed.

NOTE: If your system does not have a CD/DVD drive, an externally attached

USB CD/DVD drive can be used.

3

In the

Select Language

window, select

English

.

4

From the

Systems Deployment Options

table, click

Configure

from the

same row that contains the

Server OS Installation

option. The

Configure

Server Operating System

Installation

window is displayed.

The Server Operating System Installation (SOI) module in the

Dell

Systems Build and Update Utility enables you to install

Dell-supported operating systems on your Dell systems.

NOTE: For more information on using the specific SOI windows, see the

Dell

Systems Build and Update Utility online help.

5

In the

Set Date and Time

window of the SOI module, set the current date,

time, and the time zone and click

Continue

.

6

In the

Select an Operating System to Install

window:

a

Select

Microsoft Windows Server 2003 SP2 R2 x64 Edition

or

Microsoft Windows Server 2008 x64 (64 bit Edition)

as per the

requirement.

b

Click

Continue.

7

In the

Select RAID Configuration

window, select default selections and

click

Continue

.

NOTE: This menu may not appear depending on the system configuration.

8

If you selected

Microsoft Windows Server 2008 x64 (64 bit Edition)

on

the

Select an Operating System to Install

window, go to step 11.

Installing and Configuring the Operating System 15

9

In the

Configure the Disk Partition

window,

a

Choose to resize the boot partition or leave it at the default selection.

b

Click

Continue

.

10

In the

Enter Operating System Configuration Information

window,

a

Enter the appropriate organization, user name, product ID and

Computer Name.

b

Enter all the other necessary information.

c

Click

Install SNMP

(default).

d

Click

Install Server Administrator

(default) if you want to install the

Dell OpenManage Server Administrator Utility.

NOTE: The Dell Server Administrator can be installed anytime after the

operating system is

installed.

e

Click

Continue.

11

For Windows Server 2008 x64 installation, click

Eject CD/DVD

. In the

Operating System Installation Summary

window, click

Eject CD/DVD

Automatically

(default) and click

Continue

.

NOTE: Once you click Apply Now, the installation begins and you cannot

change the configuration details of your system.

12

Click

Apply Now

.

The Systems Build and Update Utility installation begins.

NOTE: This procedure may take several minutes to complete.

13

If you selected Microsoft Windows Server 2003 Service Pack 2 x64 Edition

when prompted, insert the appropriate Windows Server 2003 SP2

Enterprise or Standard x64 Edition media in the CD drive.

NOTE: This procedure may take several minutes to complete.

14

When the Systems Build and Update Utility installation is complete,

the system automatically reboots.

NOTE: Ensure that you remove all bootable media when the system reboots.

15

On the reboot, the system boots into the operating system install.

NOTE: Do not boot directly to the operating system media in DVD-ROM.

16 Installing and Configuring the Operating System

Continuing With the Operating System

Installation

Installing Windows Server 2003

1

If you chose Microsoft Windows Server 2003 R2 SP2 x64 Edition during

the Dell Systems Build and Update Utility installation process then on the

reboot, the system boots automatically into the Windows Server 2003 R2

SP2 x64 Edition install mode.

2

In the

Personalize Your Software

window in the Name and Organization

fields, enter the appropriate information and click

3

When prompted, enter your Product Key for Windows Server 2003 R2 SP2

Standard/Enterprise x64 Edition and click

CAUTION: Do not leave the administrator password blank.

4

In the

Computer Name

and

Administrator Password

fields, enter the

appropriate information and click

NOTE: To configure the public network properly, the computer name and

public host name must be identical.

NOTE: Record the logon password that you created in this step. You will need

this information in

step 5.

5

When the installation procedure is completed, the

Welcome to Windows

window is displayed.

a

Shut down the system, reconnect all external storage devices, and start

the system.

b

In the

Welcome to Windows

window, press <Ctrl><Alt><Delete>

to continue. The

Log On

window is displayed.

c

In the

Password

field, type the administrator password that you

created in

step 4 in this procedure and click

OK

.

You are prompted to insert the

Microsoft

Windows Server CD2

. You

can insert the Windows Server CD2 or click

Cancel

.

NOTE: If you insert the Windows Server CD2, follow the prompts through the

normal installation process. The following process assumes you are not

inserting the Windows Server CD2.

Installing and Configuring the Operating System 17

d

Click

Cancel

. A message is displayed informing you that media on

Windows Server CD2 is not going to be installed.

e

Click

OK.

You are prompted to configure Windows Server Post-Setup

(optional).

f

Click

Finish

. You are prompted to close the page.

g

Click

Yes

. The

Manage Your Server Windows Management

window is

displayed.

h

Close the window.

NOTE: To use the Broadcom Advanced Control Suite 3 (BACS), install

Microsoft .NET Framework 2.0. The Microsoft .NET Framework 2.0 can be

downloaded from microsoft.com.

Installing Windows Server 2008 SP2

1

If you chose Microsoft Windows Server 2008 x64 (64 bit Edition) during

the Dell Systems Build and Update Utility installation process then on the

reboot the Systems Build and Update Utility installer will prompt to insert

a valid Windows Server 2008 media into DVD drive. Insert the

Windows

Server 2008 SP2

media into DVD drive and click

OK

.

2

Click

OK

on the

Valid Microsoft Windows Server 2008 SP2 media

window to start the installation.

3

In the next window, enter the language and other preferences and

click

4

Click

Install now

to start the installation.

5

Key in the product key for activation and click

6

In the next window,

a

Select

Windows Server 2008 Enterprise (Full Installation)

.

b

Click

7

In the

license term

window,

a

Check the box for

I accept the license terms.

b

Click

18 Installing and Configuring the Operating System

8

In the next window,

a

Select

Custom (Advanced) Installation.

b

Select the disk where you want to install Windows.

c

Click

Next.

The installer starts the Windows installation.

NOTE: This procedure may take several minutes to complete.

9

At the end of the installation, change the Administrator password.

CAUTION: Do not leave the administrator password blank.

NOTE: To use the Broadcom Advanced Control Suite (BACS), install Microsoft .NET

Framework 2.0 or higher if not installed already. The

Microsoft .NET Framework can

be downloaded from microsoft.com.

Installing the Resource CD

NOTE: You can download the Windows Resource CD for your configuration from

dell.com/oracle.

1

Insert the media labeled

Dell RCD x64 4.4

.

2

Double-click

My Computer

, and double-click your CD-ROM drive.

3

Run

install_drivers.bat

.

NOTE: This procedure may take several minutes to complete.

4

Press any key to continue.

5

If you need to install the driver for a Qlogic Fibre Channel HBA on your

system:

• For Windows Server 2003, see installing the Driver "For Windows

Server 2003:" on page 19.

• For Windows Server 2008, see installing the Driver "For Windows

Server 2008:" on page 20.

Installing and Configuring the Operating System 19

6

Check the logs to verify that all drivers were installed correctly.

NOTE: Log information can be found at: <Primary

Drive:/>Dell_Resource_CD/logs>.

7

When the installation is complete, remove the media from the CD drive.

8

Reboot your system.

Installing the Driver for a Qlogic Fibre Channel HBA

For Windows Server 2003:

1

Start the Device Manager as follows:

a

Click

Start

, and then click

Run

.

b

In the

Run

box, type

devmgmt.msc

, and then click

OK

.

2

In the

Device Manager

box, scroll down the list of hardware types, and

then double-click

SCSI and RAID controllers

.

3

From the devices list, double-click

QLogic Fibre Channel HBA

.

4

Click the

Driver

tab, and then click

Update Driver

to start the Hardware

Update Wizard.

5

Click

Install from a list or specific location (Advanced)

, and then click

6

Click

Don't search I will choose the driver to install

, and then click

7

Click

Have Disk

, and then navigate to the

<Primary_Drive:/>Dell_Resource_CD/drivers/R254072

folder.

8

In the

Hardware Update Wizard/Select a Device Driver

box, click

9

On the

Hardware Update Wizard/Completing the Hardware Update

Wizard

, click

Finish

.

20 Installing and Configuring the Operating System

For Windows Server 2008:

1

Start the Device Manager as follows:

a

Click

Start

, and then click

Control Panel

.

b

Click

Hardware and Sound

.

c

Click

Device Manager

.

2

Scroll down the list of hardware types, and then double-click

Storage

Controller

.

3

From the devices list, double-click

QLogic Fibre Channel HBA

.

4

Click the

Driver

tab, and then click

Update Driver

to start the

Hardware

Update Wizard

.

5

Navigate to the

<Primary_Drive:/>Dell_Resource_CD/drivers/R254072

folder, and then click

6

On the

Windows has successfully updated your software

window, click

Close

.

Verifying the Temporary Directory Paths

Verify that the paths to the Temp and Tmp directories have been set correctly.

Repeat the following steps for all nodes in the cluster.

1

Click

Start

and select

Run

.

2

In the

Open

field, type

cmd

and click

OK

.

3

At the command prompt, type

echo %Temp%

and press <Enter>.

The following path is displayed:

%SystemDrive%\Temp

where,

%SystemDrive%

is the user's local drive.

ページが読み込まれています...

Dell Supported Configurations for Oracle Database 10g R2 for Windows ユーザーガイド

Dell Supported Configurations for Oracle Database 10g R2 for Windows ユーザーガイド

他の言語で

関連論文

その他のドキュメント