Charger
UC 18YRSL
Handling instructions
Read through carefully and understand these instructions before use.
2
1
Rechargeable battery
2
Pilot lamp
3
Guide rail
4
Cooling fan
5
Caution plate
6
Name plate
7
Line
8
Before insert
9
After insert
1
2
3
4
7
7
<BSL1430>
<BSL1830>
8 9
5
6
7
12
3
4
○
5
○
○
○
6
GENERAL OPERATIONAL PRECAUTIONS
1. Keep work area clean. Cluttered areas and benches
invite accidents.
2. Avoid dangerous environment. Don’t expose power
tools and charger to rain. Don’t use power tools and
charger in damp or wet locations. And keep work area
well lit.
Never use power tools and charger near fl ammable or
explosive
materials.
Do not use tool and charger in presence of fl ammable
liquids or gases.
3. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of
the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
4. Store idle tools and charger. When not in use, tools
and charger should be stored in dry, high or locked-
up place — out of reach or
children. Store tools and
charger in a place in which the temperature is less
than 40°C.
5. Don’t abuse cord. Never carry charger by cord or yank
it to disconnect from receptacle. Keep cord from heat,
oil and sharp edges.
6. When the charger is not in use or when
being
maintained and inspected, disconnect the power cord
of the charger from the receptacle.
7. To avoid danger, always use only the specifi ed
charger.
8. Use only genuine HITACHI replacement parts.
9. Do not use power tools and charger for applications
other than those specifi ed in the Handling Instructions
.
10. To avoid personal injury, use only the accessories
or attachment recommended in these handling
instructions or in the HITACHI catalog.
11. If the supply cord is damaged, it must be replaced
by the manufacture or its service agent or a similarly
qualifi ed person in order to avoid a
hazard.
Let only the authorized service center do the
repairing. The Manufacture will not be responsible
for any damages or injuries caused by repair by the
unauthorized persons or by mishandling of the tool.
12. To ensure the designed operational integrity of power
tools and charger, do not remove installed
covers or
screws.
13. Always use the charger at the voltage specifi ed on the
nameplate.
14. Always charge the battery before use.
15. Never use a battery other than that specifi ed. Do not
connect a usual dry cell, a rechargeable battery other
than that specifi ed or a car
battery to the power tool.
16. Do not use a transformer containing a booster.
17. Do not charge the battery from an engine electric
generator or DC power supply.
18. Always charge indoors. Because the charger and
battery heat slightly during charging, charge the
battery in a place not exposed
to direct sunlight; where
the humidity is low and the ventilation is good.
19. Use the exploded assembly drawing on this handling
instructions only for authorized servicing.
20. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
21. Children should be supervised to ensure that they do
not play with the appliance.
PRECAUTIONS FOR CHARGER
1. Always charge the battery at an ambient temperature
of 0–40°C. A temperature of less than 0°C will result in
over charging which is dangerous. The battery cannot
be charged at a temperature greater than 40°C.
The most suitable temperature for charging is that of
20–25°C.
2. Do not use
the charger continuously.
When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
3. Do not allow foreign matter to enter the connector for
the rechargeable battery.
4. Never disassemble the rechargeable battery or
charger.
5. Never short-circuit the rechargeable battery.
Short-circuiting
the battery will cause a great electric
current and overheat. It results in burn or damage to
the battery.
6. Do not dispose of the battery in fi re.
If the battery is burnt, it may explode.
7. Using an exhausted battery will damage the charger.
8. Bring the battery to
the shop from which it was
purchased as soon as the post-charging battery life
becomes too short for practical use. Do not dispose of
the exhausted battery.
9. Do not insert objects into the air ventilation slots of the
charger.
Inserting metal objects or fl ammable into the charger
air ventilation
slots will result in an electrical shock
hazard or damage to the charger.
7
(2) Regarding the temperature of the rechargeable
battery.
The temperatures for rechargeable batteries are
as shown in the Table 2, and batteries that have
become hot should be cooled for a while before being
recharged.
Table 2
Rechargeable batteries
Temp er atu res at which the
battery can be recharged
BSL1430, BSL1830 0°C — 50°C
(3) Regarding recharging time
Table 3 shows the recharging time required according
to the type of battery.
Table 3 Recharging time (approx. min.) at 20°C
Battery capacity (Ah)
Battery
Voltage
Li-ion BATTERY
3.0 Ah
14.4 V
BSL1430
(8 cells)
45 min.
18 V
BSL1830
(10 cells)
45 min.
NOTE: The recharging time may vary according to the
ambient temperature.
4. Disconnect the charger’s power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after
use, and then keep it.
SPECIFICATION
CHARGER
Model UC18YRSL
Charging time Approx. 45 minutes (at 20°C)
Charging voltage 14.4 V – 18 V
Weight 0.6 kg
NOTE: The recharging time may vary according to the ambient temperature.
APPLICATION
For charging the HITACHI BATTERY.
○ BSL1430, BSL1830
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger’s power cord to the
receptacle.
When connecting the plug of the charger to a
receptacle, the pilot lamp will blink in red. (At 1-second
intervals).
2. Insert the battery into the charger.
Firmly insert the battery
into the charger until the line is
visible, as shown in Fig. 1, 2.
3. Charging
When inserting a battery in the charger, the charge
status lamp will light up continuously in red.
When the battery becomes fully recharged, the
pilot lamp will blink in red. (At 1-second intervals.)
(See Table 1)
(1) Lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or
the rechargeable battery.
Table 1
Indications of the pilot lamp
The pilot
lamp
lights or
blinks in
red.
Before
charging
Blinks
Lights for 0.5 seconds. Does not light for
0.5 seconds. (off for 0.5 seconds)
While
charging
Lights
Lights continuously
Charging
complete
Blinks
Lights for 0.5 seconds. Does not light for
0.5 seconds. (off for 0.5 seconds)
Charging
impossible
Flickers
Lights for 0.1 seconds. Does not light for
0.1 seconds. (off for 0.1 seconds)
Malfunction in the
battery or the charger
The pilot
lamp
lights in
green.
Overheat
standby
Lights
Lights continuously
Battery overheated.
Unable to charge.
(Charging will commence
when battery cools)
8
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries
and batteries that have not been used for an extended
period is not activated, the electric discharge might be
low when using them the fi rst and second time. This is
a temporary phenomenon, and
normal time required
for recharging will be restored by recharging the
batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become
completely exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery.
If you continue to use the tool and exhaust the electric
current, the battery may be
damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the battery
and recharge it
after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because it
has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the pilot lamp of the charger lights up green
.
In such a case, fi rst let the battery cool, then start
charging.
○ When the pilot lamp fl ickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or
charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about 3
seconds to confi rm that the battery being charged
with UC18YRSL is taken out, wait for a minimum of 3
seconds before reinserting it to continue charging. If
the battery is reinserted
within 3 seconds, the battery
may not be properly charged.
MAINTENANCE AND INSPECTION
1. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
2. Cleaning of the charger
When the charger is stained, wipe with a soft dry
cloth
or a cloth moistened with soapy water. Do not use
chloric solvents, gasoline or paint thinner, for they melt
plastics.
3. Store idle charger
When not in use, the charger should be stored in dry,
high or locked-up place — out of reach of children.
4. Service parts list
CAUTION
Repair, modifi cation and inspection of Hitachi Power
Tool s must be carried out by a Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power
tools, the
safety regulations and standards prescribed in each
country must be observed.
MODIFICATIONS
Hitachi Power Too ls are constantly being improved
and modifi ed to incorporate the latest technological
advancements.
Accordingly, some parts may be changed without prior
notice.
NOTE
Due to HITACHI’s continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
9
A
A
1
2
3
4
6
7
9
10
11
12
13
14
4
16
17
18
19
20
15
5
21
8
ITEM
NO.
PART NAME Q’TY
1HITACHI LABEL 1
2CASE (A) 1
3FUSE 1
4NUT M3 4
5 INSULATOR (A) 1
6FIN (A) 1
7
MACHINE SCREW (W/WASHERS) M3×12
2
8
MACHINE SCREW (W/WASHERS) M3×10
2
9CASE (B) 1
10 TAPPING SCREW (W/FLANGE) D3×18 4
11 C AS E RUBBER 4
12 PRISM 1
13 TERMINAL HOLDER 1
14 TP TAPPING SCREW D3×8 3
15 CODE 1
16 PRINTED CIRCUIT BOARD ASS’Y 1
17 INSULATOR (B) 1
18 FIN (B) 1
19 TAPPING SCREW (W/FLANGE) D3×5 2
20 FAN 1
21 NAME PLATE 1
10
11
212
Code No. C99167221 G
Printed in China
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
他の言語で
- English: Hitachi UC18YRSL User manual
関連論文
-
Hitachi CS 33EB Handling Instructions Manual
-
-
-
-
Hikoki WR 14DSDL ユーザーマニュアル
-
Hitachi WH 18DBEL Handing Instructions
-
Hikoki DV 14DBL ユーザーマニュアル
-
Hitachi CJ 18DSL Handling Instructions Manual
-
-