Hitachi UC 36YSL Handling Instructions Manual

カテゴリー
バッテリー充電器
タイプ
Handling Instructions Manual
English
Charger
UC 36YSL
Handling instructions
Keep for future reference
2
3
4
5
6
7
8
9
10
7
8
11
12
1
2
3
4
3
16
3
14
15
19
20
5
6
7
8
9
10
11
English
12
GENERAL OPERATIONAL PRECAUTIONS
1. Keep work area clean. Cluttered areas and benches invite accidents.
2. Avoid dangerous environment. Don’t expose power tools and charger to rain. Don’t
use power tools and charger in damp or wet locations. And keep work area well lit.
Never use power tools and charger near ammable or explosive materials.
Do not use tool and charger in presence of ammable liquids or gases.
3. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
4. Store idle tools and charger. When not in use, tools and charger should be stored
in dry, high or locke-up place — out of reach of children. Store tools and charger in
a place in which the temperature is less than 40°C.
5. Don’t abuse cord. Never carry charger by cord or yank it to disconnect from
receptacle. Keep cord from heat, oil and sharp edges.
6. When the charger is not in use or when being maintained and inspected,
disconnect the power cord of the charger from the receptacle.
7. To avoid danger, always use only the speci ed charger.
8. Use only genuine HITACHI replacement parts.
9. Do not use power tools and charger for applications other than those speci ed in
the Handling Instructions.
10. To avoid personal injury, use only the accessories or attachment recommended in
these handling instructions or in the HITACHI catalog.
11. If the supply cord is damaged, it must be replaced by the manufacture or its
service agent or a similarly quali ed person in order to avoid a hazard.
Let only the authorized service center do the repairing. The Manufacture will not
be responsible for any damages or injuries caused by repair by the unauthorized
persons or by mishandling of the tool.
12. To ensure the designed operational integrity of power tools and charger, do not
remove installed covers or screws.
13. Always use the charger at the voltage speci ed on the nameplate.
CONTENTS
GENERAL OPERATIONAL PRECAUTIONS ................................................12
PRECAUTIONS FOR CHARGER ................................................................. 13
SYMBOL .......................................................................................................13
SPECIFICATIONS ........................................................................................ 14
APPLICATIONS ............................................................................................14
CHARGING ..................................................................................................15
MAINTENANCE AND INSPECTION ............................................................ 19
SERVICE PARTS LIST .................................................................................20
English
13
14. Always charge the battery before use.
15. Never use a battery other than that speci ed. Do not connect a usual dry cell, a
battery other than that speci ed or a car battery to the power tool.
16. Do not use a transformer containing a booster.
17. Do not charge the battery from DC power supply.
18. Always charge indoors. Because the charger and battery heat slightly during
charging, charge the battery in a place not exposed to direct sunlight; where the
humidity is low and the ventilation is good.
19. Use the exploded assembly drawing on this handling instructions only for
authorized servicing.
PRECAUTIONS FOR CHARGER
1. Always charge the battery at an ambient temperature of -1040°C. A temperature of
less than -10°C will result in over charging which is dangerous. The battery cannot
be charged at a temperature greater than 40°C.
The most suitable temperature for charging is that of 20 – 25°C.
2. Do not use the charger continuously.
When one charging is completed, leave the charger for about 15 minutes before
the next charging of battery.
3. Do not allow foreign matter to enter the hole for connecting the battery.
4. Never disassemble the battery and charger.
5. Never short-circuit the battery.
Short-circuiting the battery will cause a great electric current and overheat. It
results in burn or damage to the battery.
6. Do not dispose of the battery in re.
If the battery is burnt, it may explode.
7. Using an exhausted battery will damage the charger.
8. Bring the battery to the shop from which it was purchased as soon as the post-
charging battery life becomes too short for practical use. Do not dispose of the
exhausted battery.
9. Do not insert object into the air ventilation slots of the charger.
Inserting metal objects or in ammables into the charger air ventilation slots will
result in electrical shock hazard or damaged charger.
SYMBOL
WARNING
The following show symbols used for the machine. Be sure that you understand their
meaning before use.
Read all safety warnings and all instructions.
English
14
SPECIFICATIONS
CHARGER ( ): cells
Charging
time
1.3 Ah BSL1415S (4), BSL1815S (5) Approx. 15 minutes
1.5 Ah
BSL1415 (4), BSL1415X (4),
BSL1815 (5), BSL1815X (5)
Approx. 15 minutes
2.0 Ah BSL1420 (4), BSL1820 (5), BSL3620 (10) Approx. 20 minutes
2.5 Ah BSL1425 (4), BSL1825 (5), BSL3625 (10) Approx. 25 minutes
2.6 Ah BSL3626 (20), BSL3626X (20) Approx. 25 minutes
3.0 Ah BSL1430 (8), BSL1830 (10), BSL2530 (14) Approx. 30 minutes
4.0 Ah BSL1440 (8), BSL1840 (10) Approx. 40 minutes
5.0 Ah BSL1450 (8), BSL1850 (10) Approx. 50 minutes
6.0 Ah BSL1460 (8), BSL1860 (10), BSL3660 (20) Approx. 60 minutes
Charging
voltage
14.4 V – 36 V
Weight 0.9 kg
APPLICATIONS
For charging the HITACHI BATTERY.
BSL1415S, BSL1415, BSL1415X, BSL1420, BSL1425, BSL1430, BSL1440, BSL1450,
BSL1460,
BSL1815S, BSL1815, BSL1815X, BSL1820, BSL1825, BSL1830, BSL1840, BSL1850,
BSL1860,
BSL2530,
BSL3620, BSL3625, BSL3626, BSL3626X, BSL3660
English
15
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger’s power cord to the receptacle. (Fig. 1)
When connecting the plug of the charger to a receptacle, the charge indicator lamp will
blink in red. (At 1-second intervals)
14.4 V Battery
(BSL1415S,
BSL1415,
BSL1415X,
BSL1420,
BSL1425,
BSL1430,
BSL1440,
BSL1450,
BSL1460)
18 V Battery
(BSL1815S,
BSL1815,
BSL1815X,
BSL1820,
BSL1825,
BSL1830,
BSL1840,
BSL1850,
BSL1860)
25.2 V Battery
(BSL2530)
36 V Battery
(BSL3620,
BSL3625,
BSL3626)
36 V Battery
(BSL3626X,
BSL3660)
Battery Capacity Lamp
Charge indicator lamp
Name plate
Ventilation
holes
Guide rail
Before insert
Fig. 1
English
16
2. lnsert the battery into the charger.
Firmly insert the battery into the charger, as shown in Fig. 1 on page 15.
3. Charging
When inserting a battery in the charger, the charge indicator lamp will light up continuously
in blue.
When the battery becomes fully recharged, the charge indicator lamp will light up continuously
in green. (See Table 1)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as shown in Table 1, according to the
condition of the charger or the battery.
Table 1
Indications of the charge indicator lamp
Charge
indicator
lamp
(RED /
BLUE /
GREEN /
PURPLE)
Before
charging
Blinks
(RED)
Lights for 0.5 seconds. Does not
light for 0.5 seconds. (o for
0.5 seconds)
Plugged into power
source
While
charging
Lights
(BLUE)
Lights continuously
Charging
complete
Lights
(GREEN)
Lights continuously
(Continuous buzzer sound:
about 6 seconds)
Overheat
standby
Blinks
(RED)
Lights for 0.3 seconds. Does not
light for 0.3 seconds. (o for
0.3 seconds)
Battery overheated.
Unable to charge.
(Charging will commence
when battery cools)
Charging
impossible
Flickers
(
PURPLE)
Lights for 0.1 seconds. Does not
light for 0.1 seconds. (o for
0.1 seconds)
(Intermittent buzzer sound:
about 2 seconds)
Malfunction in the
battery or the charger.
NOTE
When standby for cooling battery, UC36YSL cools the overheated battery by cooling fan.
(2) About the Battery Capacity Lamp
The charge capacity of a battery that is charging can be checked using the battery capacity
indicator lamp.
The lamp’s indications for the battery capacity are as shown in Table 2.
NOTE
A short time after charging is complete, the battery capacity lamp turns o .
English
17
Table 2
State of lamp Battery capacity
Blinks
Battery capacity at less than 25%
Blinks
Battery capacity at less than 50%
Blinks
Battery capacity at less than 75%
Blinks
Battery capacity at more than 75%
Lights
Charging complete
(3) Regarding the temperature of the battery.
The temperatures for batteries are as shown in the Table 3, and batteries that have
become hot should be cooled for a while before being recharged.
Table 3
Batteries
Temperature which the battery
can be recharged
BSL1415S, BSL1415, BSL1415X,
BSL1420, BSL1425,
BSL1430, BSL1440, BSL1450, BSL1460
-10°C – 50°C
BSL1815S, BSL1815, BSL1815X,
BSL1820, BSL1825,
BSL1830, BSL1840, BSL1850, BSL1860
BSL2530
BSL3620, BSL3625,
BSL3626, BSL3626X, BSL3660
English
18
(4) Regarding recharging time
Table 4 shows the recharging time required according to the type of battery.
Table 4 Recharging time (approx.) at 20°C
Battery capacity (Ah)
Battery Voltage
14.4 V 18 V 25.2 V 36 V
Li-ion Battery
1.3 Ah 15 min. 15 min.
1.5 Ah 15 min. 15 min.
2.0 Ah 20 min. 20 min. 20 min. 20 min.
2.5 Ah 25 min. 25 min. 25 min.
2.6 Ah———25 min.
3.0 Ah 30 min. 30 min. 30 min.
4.0 Ah 40 min. 40 min.
5.0 Ah 50 min. 50 min.
6.0 Ah 60 min. 60 min. 60 min.
NOTE
The recharging time may vary according to the ambient temperature.
4. Disconnect the chargers power cord from the receptacle.
5. Hold the charger rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use, and then keep it.
Regarding electric discharge in case of new batteries, etc.
As the internal chemical substance of new batteries and batteries that have not been used
for an extended period is not activated, the electric discharge might be low when using
them the rst and second time. This is a temporary phenomenon, and normal time required
for recharging will be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely exhausted.
When you feel that the power of the tool becomes weaker, stop using the tool and recharge
its battery. If you continue to use the tool and exhaust the electric current, the battery may
be damaged and its life will become shorter.
(2) Avoid recharging at high temperatures.
A battery will be hot immediately after use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and the battery life will be shortened.
Leave the battery and recharge it after it has cooled for a while.
English
19
CAUTION
If the battery is charged while it is heated because it has been left for a long time
in a location subject to direct sunlight or because the battery has just been used,
the charge indicator lamp of the charger lights for 0.3 seconds, does not light for
0.3 seconds (o for 0.3 seconds). In such a case, rst let the battery cool, then
start charging.
When the charge indicator lamp ickers (at 0.2-seconds intervals), check for and
take out any foreign objects in the chargers battery connector. If there are no
foreign objects, it is probable that the battery or charger is malfunctioning. Take it
to your authorized Service Center.
Since the built-in micro computer takes about 3 seconds to con rm that the
battery being charged with UC36YSL is taken out, wait for a minimum of
3 seconds before reinserting it to continue charging. If the battery is reinserted
within 3 seconds, the battery may not be properly charged.
Do not block the ventilation holes with cloth or other materials while charging.
MAINTENANCE AND INSPECTION
1. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that they are properly tightened. Should
any of the screws be loose, retighten them immediately. Failure to do so could result in
serious hazard.
2. Cleaning of the charger
When the charger is stained, wipe with a soft dry cloth or a cloth moistened with soapy
water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics.
3. Store idle charger
When not in use, the charger should be stored in dry, high or locked-up place out of
reach of children.
4. Service parts list
CAUTION
Repair, modi cation and inspection of Hitachi Power Tools must be carried out by
a Hitachi Authorized Service Center.
This Parts List will be helpful if presented with the tool to the Hitachi Authorized
Service Center when requesting repair or other maintenance. In the operation and
maintenance of power tools, the safety regulations and standards prescribed in
each country must be observed.
English
20
SERVICE PARTS LIST
7
8
11
12
1
2
3
4
3
16
3
14
15
19
20
5
6
7
8
9
10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Hitachi UC 36YSL Handling Instructions Manual

カテゴリー
バッテリー充電器
タイプ
Handling Instructions Manual

他の言語で