Hitachi UB 18DGL Handling Instructions

ブランド: Hitachi

モデル: UB 18DGL

タイプ: Handling Instructions

◯

UB 18DGL

⦁

◯

Hitachi Koki Co., Ltd.

WARNING

○

Be careful of electrical shock.

○

When not in use or during inspection and

maintenance, be sure to turn the switch OFF

on the unit, and remove the battery from it.

○

Do not cover the work light with cloth,

cardboards or other materials when the light

is on. Doing so may result in ﬁ re.

CAUTION

○

Do not use any other than the speciﬁ ed

batteries.

○

Do not look at the LED light directly.

○

The LED cover will remain at a high

temperature when alight and immediately

after use, so do not touch it.

○

Be sure to turn the switch OFF when not using.

○

Do not expose the work light to rain.

○

Do not shock or disassemble the work light.

○

Do not allow the work light to contact gasoline, thinner etc.

○

Do not leave the work light in a car or the like that tends to be exposed to be searching

heat of the sun (above 60 °C). Otherwise, troubles can result.

SYMBOL

WARNING

The following show symbols used for the machine. Be sure that you understand their

meaning before use.

Read all safety warnings and all instructions.

SPECIFICATIONS

LED 18 W (0.5 W × 36 Pcs.)

Dimensions (without battery) 256 mm (width) × 198 mm (length) × 252 mm (height)

Weight (without battery) 0.74 kg

Operating time (Approx.): Using full charged Battery

Battery

BSL1840 BSL1830 BSL1820 BSL1815 BSL1440 BSL1430 BSL1420 BSL1415

[High/Low]

mode (h)

5.0 / 11.5 3.5 / 8.5 2.5 / 6.0 2.0 / 4.0 3.5 / 7.5 2.5 / 5.5 2.0 / 4.0 1.5 / 3.0

LED light

(built-in)

Switch

Top handle

Bottom handle

Pipe hook

Strap hole

1/4-inch

screw hole

Fig. 1

Cordless Work Light UB 18DGL

Handling instructions

Keep for future reference

HOW TO USE

1. Battery insert/removal

Insert the battery in direction A until it

clicks. To remove, extract it in direction B

while holding down the latch. (Fig. 2)

2. Turning on the light

Press the switch to turn on the light.

The light setting will alternate between

[Strong], [Weak] and [Oﬀ ] whenever the

switch is pressed.

3. Light angle adjustment

The angle of the light can be adjusted within a range

of approximately 120 degrees both upward and

downward. (Fig. 3)

4. Installation

In addition to placing it directly onto the ﬂ oor or other

ﬂ at surface, the unit can also be installed as follows.

⦁

Attached to a tripod with the use of a 1/4-inch screw. (Fig. 4)

⦁

Suspended from a pipe with the use of the pipe hook. (Fig. 5)

⦁

Hung on the wall with the use of the wall-hanging hook. (Fig. 6)

CAUTION

○

There are cases in which it will not be possible to turn

on the light owing to a function to prevent the batteries

from over-discharging. IN this event, either replace the

batteries or recharge them.

○

Use cord or a similar article to ﬁ x the unit in place to

prevent it from falling.

NOTE

Make sure the instruction manuals supplied with the

separately-purchased rechargers and batteries are read

thoroughly prior to use.

Battery (sold separately)

Latch

Fig. 2

120°

Fig. 3

1/4-inch screw hole

Fig. 4

Item

No.

Part Name Q’TY

1 HEXGON HEAD TAPPING SCREW D4×12 4

2FRONT CABINET 1

3LENS 1

4PCB 1

5 TAPPING SCREW D3×8 6

6 MAIN BODY 1

Fig. 5

Wall-hanging hook

Bottom handle

Fig. 6

Hitachi Koki Co., Ltd.

Code No. C99210821 NA

Hitachi UB 18DGL Handling Instructions

ブランド: Hitachi

モデル: UB 18DGL

タイプ: Handling Instructions

PDFをダウンロードします

報告

他の言語で

English: Hitachi UB 18DGL

Hitachi UB 18DGL Handling Instructions

Hitachi UB 18DGL Handling Instructions

他の言語で

関連論文