Epson TM-H2000 ユーザーマニュアル

ブランド: Epson

モデル: TM-H2000

タイプ: ユーザーマニュアル

User’s Manual

Printed in China

Introduction

The UB-S09, designed for Epson TM printers and

Epson customer displays, is a serial interface that

has a maximum transmission speed of 115.2K bps

[bps: bits per second] with the TM printers or DM-

D series applicable to this product.

This manual provides instructions for operators of

POS systems in which the UB-S09 is installed so

that the operators can use the UB-S09 safely and

correctly. For information about installation and

settings required, see the UB-S09 Developer’s

Guide. Contact your Epson representative or your

place of purchase to get the UB-S09 Developer’s

Guide.

Key to Symbols

The symbols in this manual are identified by their

level of importance, as defined below. Read the

following carefully before handling the product.

CAUTION:

Observe cautions to avoid minor injury to yourself,

damage to your equipment, or loss of data.

Note:

Notes have important information and useful tips

on the operation of your equipment.

Caution Label

The following caution label is visible near the

modular connector (customer display connector).

The label has the following meaning:

“Use a modular connector specifically designed for

a customer display for this product. Do not

connect this connector to an ordinary telephone

line.”

Part Names

The following view shows the part names of the

UB-S09.

serial interface

connector

caution

label

customer display

connector

Connecting the Cables

Before connecting any of the cables, make sure that

both the printer and the host computer are turned

off.

Connecting the interface cable

1. Make sure both the printer and the host

computer are turned off.

2. Plug the cable connector securely into the

UB-S09’s interface connector.

3. Tighten the screws on both sides of the

connector.

Note:

If your interface connector has a grounding

wire, attach it to the printer using either of the

screws that fasten the UB-S09 to the printer.

4. Attach the other end of the cable to the host

computer.

Connecting the display module cable

1. Make sure both the printer and the host

computer are turned off.

2. Disconnect the power supply from the

printer.

CAUTION:

You must disconnect the power supply

because the electrical current is flowing in

some parts of the printer circuit even when the

power switch is turned off; otherwise you may

damage the UB-S09 and the printer.

3. Plug the cable connector (provided with the

direct connection display module) securely

into the UB-S09’s display module connector

until it clicks.

CAUTION:

Do not connect this connector to an ordinary

telephone line.

Note:

Never connect customer display connectors to

both the UB-S09 and the TM printer at the

same time.

4. Connect the power supply to the printer.

customer display

connector

Standards and Approvals

The following standards are also applied only to

the units that are so labeled. (EMC is tested using

the Epson power supply and TM series printer.)

Europe: CE marking

North America: FCC Class A, ICES-003 Class A

Oceania: Radiocommunications

(Electromagnetic Compatibility)

Standard, Class A

For Users in Europe

CE Marking

☞ http://www.epson.eu/conformity

WARNING

This is a Class A product. In a domestic

environment this product may cause radio

interference, in which case the user may be

required to take adequate measures.

The printers in which this board is installed

becomes class A devices.

Indication of the manufacturer and the

importer in accordance with requirements

of directive 2011/65/EU (RoHS)

Manufacturer: SEIKO EPSON CORPORATION

Address: 3-5, Owa 3-chome, Suwa-shi,

Nagano-ken 392-8502, Japan

Web site: http://www.epson.com/

Importer: EPSON EUROPE B.V.

Address: Atlas Arena, Asia Building,

Hoogoorddreef 5,1101 BA

Amsterdam Zuidoost The

Netherlands

Web site: http://www.epson.eu/

Türkiye'deki kullanıcılar için

AEEE Yönetmeliğine Uygundur.

Ürünün Sanayi ve Ticaret Bakanlığınca tespit ve

ilan edilen kullanma ömrü 5 yıldır. Tüketicilerin

şikayet ve itirazları konusundaki başvuruları

tüketici mahkemelerine ve tüketici hakem

heyetlerine yapılabilir.

Üretici: SEIKO EPSON CORPORATION

Adres: 3-5, Owa 3-chome, Suwa-shi,

Nagano-ken 392-8502 Japan

Tel: 81-266-52-3131

Web: http://www.epson.com/

For Users in the Americas

WARNING

The connection of a non-shielded interface cable to

this board will invalidate the EMC standards of this

device.

You are cautioned that changes or modifications

not expressly approved by the party responsible for

compliance could void your authority to operate

the equipment.

FCC Compliance Statement for Users in the

USA

This equipment has been tested and found to

comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference when the equipment

is operated in a commercial environment.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instruction manual,

may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is

likely to cause harmful interference, in which case

the user will be required to correct the interference

at his own expense.

For Users in Canada

This class A digital apparatus complies with

Canadian ICES-003.

Pour les utilisateurs au Canada

Cet appareil numérique de classe A est conforme à

la norme canadienne NMB-003.

For Users in Oceania

WARNING

This is a Class A product. In a domestic

environment this product may cause radio

interference in which case the user may be required

to take adequate measures.

be reproduced, stored in a retrieval system, or

transmitted in any form or by any means,

electronic, mechanical, photocopying, recording,

or otherwise, without the prior written permission

of Seiko Epson Corporation.

The contents of this manual are subject to change

without notice.

While every precaution has been taken in the

preparation of this manual, Seiko Epson

Corporation assumes no responsibility for errors

or omissions.

Neither is any liability assumed for damages

resulting from the use of the information

contained herein.

Neither Seiko Epson Corporation nor its affiliates

shall be liable to the purchaser of this product or

third parties for damages, losses, costs, or expenses

incurred by purchaser or third parties as a result of:

accident, misuse, or abuse of this product or

unauthorized modifications, repairs, or alterations

to this product, or (excluding the U.S.) failure to

strictly comply with Seiko Epson Corporation’s

operating and maintenance instructions.

Seiko Epson Corporation shall not be liable for any

damages or problems arising from the use of any

options or any consumable products other than

those designated as Original Epson Products or

Epson Approved Products by Seiko Epson

Corporation.

EPSON is a registered trademark of Seiko Epson

Corporation. Exceed Your Vision is a registered

trademark or trademark of Seiko Epson

Corporation. All other trademarks are the property

of their respective owners and used for

identification purpose only. Product information is

subject to change without due notice.

Printed in China

用户手册

Printed in China/ 中国印刷

介绍

为EpsonTM打印机和Epson用户显示器而设

计的UB-S09，是一个串行口，其与TM打印

机或应用于本产品上的DM-D串行口之间的

最大传输速率为115.2Kbps。[bps: 每秒字

节数]。

本手册提供了有关安装有UB-S09 的POS 系

统的操作说明，以便操作者可以安全正确

地使用UB-S09。有关安装和所需设置的信

息，参见

UB-S09开发员指南

。若想得到UB-

S09

开发员指南

请与Epson的销售代表或购

买处联系。

重要符号

如下所述，通过重要度等级识别本手册中

的符号。在使用本产品前应仔细阅读以下

内容。

注意:

必须留意注意的内容，以避免身体造成轻

微损伤、设备损坏和数据损失。

注:

注释记有有关打印机操作的重要信息和有

用的提示。

注意标签

在标准接头旁边可以看到以下注意标签

（用户显示器接头）。

此标签代表以下内容:

“使用为本产品的用户显示器而特殊设计

的标准接头。不要将普通的电话线连接到

此接头上”。

部件名称

下图显示了UB-S09的部件名称。

连接电缆

在连接任何电缆前，确保关闭主机和打印机。

连接接口电缆

1. 确保关闭主机和打印机。

2. 将电缆接头稳固插在UB-S09的接口上。

3. 拧紧接头两侧的螺丝。

注:

如果您的接口有接地线,则使用固定

UB-S09 的螺丝将接地线固定在打印机

上。

4. 将电缆的另一端连接到主机上。

用户显示器接头注意标签串行口接头

连接显示器组件电缆

1. 确保关闭主机和打印机。

2. 断开打印机的电源。

注意:

您必须断开电源，否则您可能损坏UB-

S09和打印机。因为即使关闭了电源开

关在打印机电路上仍有一些部件有电

流。

3. 将电缆接头（随直接连接显示器模块

提供）稳固地插在UB-S09 的显示器标

准接头上，直到其卡住。

注意:

不要将普通的电话线连接到此接头

上。

注:

禁止同时将用户显示器接头连接到UB-

S09和TM打印机上。

4. 将电源连接到打印机上。

对于中国的用户

产品中有害物质的名称及含量

产品环保使用期限的使用条件

在中国销售的电子电气产品的环保使用期限，表示按照本产品的安全使用注意事项使用

的情况下，从生产日开始，在标志的年限内使用，本产品含有的有害物质不会对环境、人

身和财产造成严重影响。

用户显示器接头

警告：此为 A 级产品，在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可

能需要用户对其干扰采取切实可行的措施。

部件名称

有害物质

铅

（Pb）

汞

（Hg）

镉

（Cd）

六价铭

（Cr（VI））

多溴联苯

（PBB）

多溴二苯醚

（PBDE）

印刷电路板/电子部件 × ○ ○ ○ ○ ○

本表格依据SJ/T11364的规定编制。

○ 表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572规定的限量要求以下。

× 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572规定的限量要求。

但这只是因为在保证产品性能和功能条件下，现在还没有可替代的材料和技术而被使用。

Epson TM-H2000 ユーザーマニュアル

ブランド: Epson

モデル: TM-H2000

タイプ: ユーザーマニュアル

PDFをダウンロードします

報告

他の言語で

English: Epson TM-H2000 User manual

Epson TM-H2000 ユーザーマニュアル

Epson TM-H2000 ユーザーマニュアル

他の言語で

関連論文