Drum Stand
MDS-12X
組み立てかた
内容物
主な特長
完成図
主な仕様
スタンドを開いた状態
●必要占有面積
●パイプ径
●質量
A
B
C
D
E
F
G
H
I
J
K
L
A B
C
E
D
F G H I J K
L
ラベル KIK SNR T1 T2 T3 HH HHC
ラベル CR1 CR2 RD RDE AX1 AX2
©
L
K
K
L
A
B
B
C
E
D
F G
H
I
I
I
J J
5
3
2
1
6
7
8
L
1.3 m
120˚
120˚
ボルト
1 8
4
ロッド
ボール
クランプ
600
mm
550 mm
Height
memory
Label
A B
C
E F G H I J K
L
Drum Stand Owner’s Manual
MDS-12X
Important in Setting Up the Stand
When assembling the stand, you should cover the floor with a mat, blanket, etc., so as to prevent damage to *
the floor as well as to the stand.
To prevent topp * ling, begin the assembly with the stand placed horizontally on the floor. Do not raise the
stand into the upright position until it has been sufficiently assembled.
Make sure to firmly tighten all hand knobs and bolts after you have assembled the stand and attached any *
components. You should probably also try to make a habit of checking and retightening them if necessary
before every performance. You risk injury if you have loose screws or clamps, since a pad or component can
fall unexpectedly.
When setting up or storing the stand, be careful not to pinch your hands or fingers in the stand joints. *
Do not apply undue force to the hand knobs, pipes, mounts, etc. *
Do not open the stand wider than 120 degrees outward. Be sure * the
two pipes at the ends tare no more than 1.3 meters apart. Doing so
can damage the cables inside the stand or cause the stand to fall
ove r.
Never pull on any cables with excessive force. *
There are labels on the ends of the cables allowing easy connection to your sound module. *
For about connections, refer to the owners manual that came with your sound module.
The names on the labels correspond to trigger input jack names as follows.
(input names shown here are for the TD-12 modules)
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (separate
sheet). These sections provide important information concerning the proper operation of the unit. Additionally, in order to
feel assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should be read
in its entirety. The manual should be saved and kept on hand as a convenient reference.
Setting Up The Stand
Components
Main Features
Fully Assembled View
View of Stand When Spread Open •
Specifications
We recommend using an optional Roland drum mat (TDM series) to prevent scarring or discoloration of *
flooring by the rubber feet of the stand.
View of Stand When Spread Open
A very solid and stable stand featuring ball clamps that allow precise adjustments for all pads and cymbals.•
Cables are inside the pipes, providing a clean look and quick breakdown or setup.•
1.3 m
(51-3/16”)
120˚
120˚
Required Space for Set-up•
1,200 (W) x 700 (D) x 1,100 (H) mm / 47-1/4 (W) x 27-9/16 (D) x 43-5/16 (H) inches (Drum Stand only)
1,500 (W) x 1,200 (D) x 1,250 (H) mm / 59-1/16 (W) x 47-1/4 (D) x 49-1/4 (H) inches
(including Sound Module, Kick Pad, Cymbals and Stool)
Tube Diameter•
Stand: 38.1 mm / 1-1/2 inches
Pad Arm/Cymbal Arm: 22.2 mm / 7/8 inches
Weight•
16.8 kg / 37 lbs 1 oz (including Pad Mounts and Cymbal Mounts)
In the interest of product improvement, the specications and/ or appearance of this unit are subject to change without prior *
notice.
Working in order, following numbers – in the illustration, attach the curved
pipes to the straight pipes.
Of pipes “B,” the long one (600 mm) is Curved Pipe L, and the short one (550 mm) *
is the Center Pipe.
Do not pass any cables through pipe “C” (Curved Pipe R). *
A Sound module mounting pipe (including the mounting plate)
B Curved pipe L 600mm, Center pipe 550 mm (connection cables are inside)
C Curved pipe R
D Snare pipe 300 mm
E Straight pipe 625 mm
F Straight pipe 650 mm L
G Straight pipe 650 mm R
H Straight pipe 520 mm
I Cymbal arm x 3
J Pad arm x 2
K Holder x 2
L Pad mount x 2, Memory lock (for pad mount) x 2
Drum key
Cable clip
Owner´s manual (this leaet)
Label KIK SNR T1 T2 T3 HH HHC
Jack KICK SNARE TOM 1 TOM 2 TOM 3 HI-HAT HH CTRL
Label CR1 CR2 RD RDE AX1 AX2
Jack CRASH1 CRASH2 RIDE EDGE AUX 1 AUX 2
Cable
Use the cable clips
as shown below, to
secure the cables.
Cable
clip
Position the cable in front•
Align to position of •
Height Memory
A B
B
C
E
D
F G
H
I
I
I
J J
Align to position of
Height Memory
Copyright © 2009 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in
any form without the written permission of ROLAND CORPORATION.
Roland and V-Drums are either registered trademarks or trademarks of
Roland Corporation in the United States and/or other countries.
L
K
K
L
5
2
1
3
6
7
8
Cable
D
L
Bolt
4
1 8
Loosen the bolt using 1.
the drum key, then
remove the ball clamp.
Position the rod in the
2.
upright position, then
reattach the ball clamp.
Rod
Ball Clamp
Setting Up
/
