CyberPower OL3000XL ユーザーマニュアル

ブランド: CyberPower

モデル: OL3000XL

カテゴリー: 無停電電源装置（UPS）

タイプ: ユーザーマニュアル

このマニュアルも適しています

User’s Manual

OL1000XL

OL1500XL

OL2200XL

OL3000XL

CyberPower Systems (USA), Inc.

4241 12th Avenue East Suite 400 Shakopee, MN 55379

Phone: 877-297-6937

Fax: 952-403-0009

www.CPSww.com

K01-0000356-00

碩天科技股份有限公司

重要安全警語

本手冊包含重要的操作說明，應遵循安裝並維護 UPS 和電池。請仔細閱讀並遵守所有的安裝指引與

警示。安裝前需仔細閱讀本手冊再進行安裝與操作。

注意！ UPS 須接到具地線的電源插座，並有保險絲或斷路器等過電流保護器。

注意！如需關閉連接到 UPS 的設備時，請先關閉 UPS 電源再拔掉插頭。

注意！不得使用在醫療或生命維護設備！ CyberPower 並不銷售產品在生命維護或醫療應用上，

任何影響生命維護、醫療應用或病人護理等皆不得使用。

注意！在 UPS 電池模式下，電池接頭斷開可以切斷危險的帶電元件。

注意！為了防止火災或觸電危險，UPS 需安裝在溫度和濕度合理控制下的室內環境。（請參閱規格

可接受的溫度和濕度範圍）。

注意！為了減少觸電危險，勿取下上蓋。除電池可替換外，內部無其他可供使用者維修的零件。

注意！為了避免觸電危險，在更換電池或作為電腦設備備用電源前，請先關閉 UPS 電源開關。

注意！不得使用在水族箱或相關水源設備上！為降低發生火災的風險，任何有潛在水源處皆不得

使用，如壓縮機冷凝水會導致機器短路起火。

注意！交流輸出電纜使用長度不得超過 10 米。

注意！電池有可能會產生相當大的短路電流，所以在對電池進行更換或維修時，請務必採取以下

措施，並由經授權的合格專業人員進行維護。

1. 取下身上的手表、戒指、項鍊或其他金屬物品。

2. 使用具有絕緣握把的工具。

注意！ UPS 電池可產生能源。在 UPS 的輸入沒有連接至交流電源時，其輸出插座可能帶有電壓。

注意！ UPS 開啟時，請勿拔下輸入線。這會使 UPS 及其連接設備的安全接地失效。

注意！為了防止觸電，在安裝輸入線及輸出線時，請先關閉交流電源及 UPS。並請優先配接安全

接地的部分。

注意！為了防止火災，在安裝輸入線及輸出線時，請使用正確尺寸的電源線。並由經授權的合格

專業人員安裝。

注意！為了防止爆炸，請勿將電池丟入火中。

注意！不要打開或毀壞電池，釋出的電解液對皮膚和眼睛是有害的。

注意！不要阻塞 UPS 前後左右的外殼通風口。

注意！不要連接家用電器如吹風機到 UPS 的輸出插座。

這是甲類的產品，在住宅環境中，此一產品可能會造成無線電干擾，在此情況下，使用者可能會被

要求採取額外的處置。

警告使用者

碩天科技股份有限公司

規格說明

Smart App Online UPS

型號

額定電壓/電流

最大功率

OL1000XL

輸入

AC 120V(＋6%/－10%), 8.4A MAX, 50/60Hz

輸出

AC 120V, 8.4A MAX, 50/60Hz

1000VA/900W

OL1500XL

輸入

AC 120V (＋6%/－10%), 12.5A MAX, 50/60Hz

輸出

AC 120V, 12.5A MAX, 50/60Hz

1500VA/1350W

OL2200XL

輸入

AC 120V (＋6%/－10%), 18.4A MAX, 50/60Hz

輸出

AC 120V, 18.4A MAX, 50/60Hz

2200VA/1800W

OL3000XL

輸入

AC 120V (＋6%/－10%), 25.0A MAX, 50/60Hz

輸出

AC 120V, 25.0A MAX, 50/60Hz

3000VA/2700W

1. 電池的壽命隨環境溫度的升高而縮短。定期更換電池可保證 UPS 工作正常，並保證足夠的後備

時間。

2. 蓄電池維護必須由具備蓄電池專業知識的人員來進行。

3. 更換蓄電池，其類型、型號與數量均應與原電池保持一致。

4. 蓄電池存在電擊危險和短路電流危險。為避免觸電傷人事故，在更換電池時，請遵守下列警告：

A. 請勿佩帶手錶、戒指或類似金屬物體。

B. 使用絕緣的工具。

C. 穿戴橡膠鞋和絕緣手套。

D. 請勿將金屬工具或類似的金屬零件放在電池上。

E. 在拆電池連接端子前，必須先斷開連接在電池上的負載。

5. 請勿將蓄電池暴露於火中，以免引起爆炸，危及人身安全。

6. 非專業人士請勿打開或損毀蓄電池，因為電池中的電解液含有強酸等危險物質，會對皮膚和眼睛

造成傷害。如果不小心接觸到電解液，應立即用大量的清水進行清洗，並去醫院檢查。

7. 請勿將電池正負極短路，會導致電擊或著火

電池安全

IMPORTANT SAFETY INSTRUCTIONS

This manual contains important instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual

thoroughly before attempting to unpack, install, or operate the UPS.

CAUTION! The UPS must be connected to a grounded AC power

outlet with fuse or circuit breaker protection. DO NOT plug the UPS into

an outlet that is not grounded. If you need to power-drain this equipment,

turn off and unplug the unit.

CAUTION! The battery can power hazardous components inside the

unit, even when the AC input power is disconnected.

CAUTION! The UPS should be placed near the connected equipment

and easily accessible.

CAUTION! To prevent the risk of fire or electric shock, install in a

temperature and humidity controlled indoor area, free of conductive

contaminants. (Please see specifications for acceptable temperature and

humidity range).

CAUTION! (No User Serviceable Parts): Risk of electric shock, do

not remove cover. No user serviceable parts inside. Refer servicing to

qualified service personnel.

CAUTION! (Non-Isolated Battery Supply): Risk of electric shock,

battery circuit is not isolated from AC power source; hazardous voltage

may exist between battery terminals and ground. Test before touching.

CAUTION! To reduce the risk of fire, connect the UPS to a branch

circuit with 12 amperes (OL1000) / 15 amperes (OL1500) / 20 amperes

(OL2200) / 30 amperes (OL3000) maximum over-current protection in

accordance with the National Electric Code, ANSI/NFPA 70.

CAUTION! The AC outlet where the UPS is connected should be close

to the unit and easily accessible.

CAUTION! Please use only UL-marked mains cable, (e.g. the mains

cable of your equipment), to connect the UPS to the AC outlet.

CAUTION! Please use only UL-marked power cables to connect any

equipment to the UPS.

CAUTION! When installing the equipment, ensure that the sum of the

leakage current of the UPS and the connected equipment does not

exceed 3.5mA.

CAUTION! The OL1000 / OL1500 / OL2200 / OL3000 models may

only be installed by qualified maintenance personnel..

CAUTION! Do not unplug the unit from AC Power during operation, as

this will invalidate the protective ground insulation.

CAUTION! To avoid electric shock, turn off and unplug the unit before

installing the input/output power cord with a ground wire. Connect the

ground wire prior to connecting the line wires!

CAUTION! Do not use an improper size power cord as it may cause

damage to your equipment and cause fire hazards.

CAUTION! Wiring must be done by qualified personnel.

CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT

EQUIPMENT! Under no circumstances this unit should be used for

medical applications involving life support equipment and/or patient care.

CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce

the risk of fire, do not use with or near aquariums. Condensation from

the aquarium can come in contact with metal electrical contacts and

cause the machine to short out.

CAUTION! Do not dispose of batteries in fire as the battery may

explode.

CAUTION! Do not open or mutilate the battery, released electrolyte is

harmful to the skin and eyes.

CAUTION! A battery can present a risk of electric shock and high short

circuit current. The following precaution should be observed when

working on batteries

1. Remove watches, rings or other metal objects.

2. Use tools with insulated handles.

CAUTION! The unit has a dangerous amount of voltage. When the

UPS indicators is on, the units may continue to supply power thus the

unit’s outlets may have a dangerous amount of voltage even when it’s not

plugged in to the wall outlet.

CAUTION! Make sure everything is turned off and disconnected

completely before conducting any maintenance, repairs or shipment.

CAUTION! Connect the Protection Earth (PE) safety conductor before

any other cables are connected.

WARNING! (Fuses): To reduce the risk of fire, replace only with the

same type and rating of fuse.

DO NOT INSTALL THE UPS WHERE IT WOULD BE EXPOSED TO

DIRECT SUNLIGHT OR NEAR A STRONG HEAT SOURCE!

DO NOT BLOCK OFF VENTILATION OPENINGS AROUND THE

HOUSING!

DO NOT CONNECT DOMESTIC APPLIANCES SUCH AS HAIR

DRYERS TO UPS OUTPUT SOCKETS!

SERVICING OF BATTERIES SHOULD BE PERFORMED OR

SUPERVISED BY PERSONNEL KNOWLEDGE OF BATTERIES AND

THE REQUIRED PRECAUTIONS. KEEP UNAUTHORIZED

PERSONNEL AWAY FROM BATTERIES!

UNPACKING

1K/1.5KVA or 2.2K/3KVA UPS

User’s manual Register card

Phone line

USB communication cable

Serial Interface Cable (RS-232)

PowerPanel® Business Edition software CD

SAFETY PRECAUTIONS

CAUTION! Installation environment should be in a temperature and humidity controlled indoor area free of conductive contaminants. Do not install this UPS

where excessive moisture or heat is present (Please see specifications for acceptable temperature and humidity range).

CAUTION! Never install a UPS, or associated wiring or equipment, during a lightning storm.

CAUTION! Do not work alone under hazardous conditions.

CAUTION! In case of the risk of electric shock, do not remove the top cover.

CAUTION! The battery can energize hazardous live parts inside even when the AC input power is disconnected.

INSTALLING YOUR UPS SYSTEM

SYSTEM BLOCK DIAGRAM

Output

Input

Filter

PFC

AC/DC

BUS

Inverter

DC/AC

INV

Charger

AC/DC

Bypass

Battery

Output

Filter

Input

Line Mode

Battery Mode

Bypass Mode

Control

Monitoring

LCD Module

USB & DB9

SNMP Slot

DC/DC

HARDWARE INSTALLATION GUIDE

1. Battery charge loss may occur during shipping and storage. Before

using the UPS, it’s strongly recommended to charge batteries for four

hours to ensure the batteries’ maximum charge capacity. To recharge the

batteries, simply plug the UPS into an AC outlet.

2. When using the included software, connect either the serial or the

USB cable between the computer and the corresponding port on the UPS.

Note: If the USB port is used, the serial port will be disabled. They cannot

be used simultaneously. After connecting to either the USB port or the

Serial port on the UPS, a computer with the PowerPanel

Business

Edition Agent software installed can control the operating schedule,

battery test, outlets, as well as obtain UPS status information. However,

other computers with PowerPanel

Business Edition Client software can

only obtain UPS status information via LAN connection.

3. Connect your computer, monitor, and any externally-powered data

storage device (Hard drive, Tape drive, etc.) into the outlets only when

the UPS is off and unplugged. DO NOT plug a laser printer, copier, space

heater, vacuum, paper shredder or other large electrical device into the

UPS. The power demands of these devices will overload and possibly

damage the unit.

4. To protect a fax machine, telephone, modem line or network cable,

connect the telephone or network cable from the wall jack outlet to the

jack marked “IN” on the UPS and connect a telephone cable or network

cable from the jack marked “OUT” on the UPS to the modem, computer,

telephone, fax machine, or network device.

5. Press the ON/OFF switch to turn the UPS on. The Power-On indicator

light will display when activated. If an overload is detected, an audible

alarm will sound and the UPS will continuously emit two beeps per

second. For resetting the unit, unplug some equipment from the outlets.

Make sure your equipment carries a load current within the unit’s safe

range, (refer to the technical specifications).

6. This UPS is equipped with an auto-charge feature. When the UPS is

plugged into an AC outlet, the battery will automatically charge, even

when the unit is switched off.

7. To maintain an optimal battery charge, leave the UPS plugged into an

AC outlet at all times.

8. Before storing the UPS for an extended period of time, turn the unit

OFF. Then cover it and store it with the batteries fully charged. Recharge

the batteries every three months to ensure good battery capacity and

long battery life. Maintaining a good battery charge will help prevent

possible damage to the unit from battery leakage.

9. The UPS has one USB port (default) and one Serial port that allows

connection and communication between the UPS and any attached

computer running the PowerPanel

Business Edition Agent software. The

UPS can control the computer’s shutdown during a power outage

through the connection while the computer can monitor the UPS and alter

various programmable parameters. Note: Only one communication port

can be used at a time. The port not in use will automatically become

disabled or the serial port will be disabled if both ports are attached.

10. EPO (Emergency Power Off) Port:

EPO ports allow administrators the capability to connect the UPS unit to

customer-supplied EPO switches. These installations give operators a

single access point to immediately power-off all equipment connected to

the UPS during an emergency.

11. To avoid electric shock, turn the unit OFF and disconnect the unit

from utility power before hardwiring the UPS (in/out power cord). The

in/out power cord MUST be grounded.

BASIC OPERATION

POWER MODULE FRONT/REAR PANEL DESCRIPTION

1. Power Button / Power on Indicator

Master ON/OFF for the UPS. Indicates that the UPS is on and supplying

power.

2. UPS Status / Fault / Replace Battery LED Indicator

Indicates the status of the UPS, displaying whether it is operating in Line,

Battery or Bypass Mode, if it has an internal fault or if the battery needs

to be replaced.

3. Multifunction LCD Readout

Shows UPS status, information, settings and events.

4. Function Buttons

Scroll up, scroll down, select and cancel LCD menu.

5. Input Circuit Breaker

Provides input overload and fault protection.

6. Battery Backup & Surge Protected Outlets

Provides battery backup and surge protection. They ensure power is

provided to connected equipment over a period of time during a power

failure.

Critical / Noncritical Load

Allows the creation of load priorities to ensure that battery power

reserves are transferred to specified outlets during a power outage. The

unit can be programmed to provide additional runtime for equipment

connected to the “CRITICAL” outlets, while stopping the power supply to

equipment connected to “NONCRITICAL” outlets after a designated

period of time.

7. Serial Port

Serial port provides communication between the UPS and the computer.

The UPS can control the computer’s shutdown during a power outage

through the connection while the computer can monitor the UPS and alter

its various programmable parameters.

8. USB port

This is a connectivity port which allows communication and control

between the UPS and the connected computer. It is recommended to

install the PowerPanel® Business Edition Agent software on the

PC/Server connected with the USB cord.

9. Surge Protected Communication Ports RJ-45/RJ-11

These ports are used to protect standard RJ-45/RJ-11 based products

(ADSL, LAN, Phone/ Modem-Lines) and cabling systems from surges.

10. Relay Output Connector

Convert UPS signals into real potential-free Dry Contacts for industrial

control.

11. SNMP/HTTP Network slot

Slot to install the optional SNMP card for remote network control and

monitoring.

12. Extended Runtime Battery Module Connector

Connection for additional CyberPower XL Battery modules.

13. EPO (Emergency Power Off) Connector

Enables an emergency UPS Power-Off from a remote location.

14. AC Input Inlet

Connect the AC Power cord to a properly wired and grounded outlet.

OL1000XL / OL1500XL OL2200XL / OL3000XL

BASIC OPERATION

OL1000XL / OL1500XL

OL2200XL OL3000XL

OPERATION INSTRUCTIONS FOR LCD MODULE

LED INDICATORS – UPS STATUS

LED Indicators

Color

UPS Status Description

ON/OFF

White

UPS power is on.

ON-LINE

Green

UPS is operating in Line Mode.

BATTERY ON

Yellow

UPS is operating in Battery Mode.

BYPASS

Yellow

UPS is operating in Bypass Mode, Manual Bypass or ECO (Economy) Mode.

FAULT

Red

UPS has an internal fault. See “Trouble Shooting” for additional information.

REPLACE BATTERY

Red

Battery will soon need to be replaced due to insufficient runtime.

LCD SCREEN – UPS STATUS

LCD Screen

UPS Status Description

Line Mode

UPS is operating in Line Mode.

Battery Mode

UPS is operating in Battery Mode.

Bypass Mode

UPS is operating in Bypass Mode.

Manual Bypass

UPS is operating in Manual Bypass.

ECO Mode

UPS is operating in ECO (Economy) Mode.

BUTTON OPERATION

Button

Operation Description

ON/OFF

Press this button to turn on or turn off UPS.

▲

Press this button to scroll up in the LCD menu.

▼

Press this button to scroll down in the LCD menu.

ENTER

Press this button to select an option.

ESC

Press this button to cancel or return to previous LCD menu.

LCD SETUP FUNCTIONS

MULTI-FUNCTION LCD MAIN MENU

Press “Enter” button to activate “MAIN MENU”.

MAIN MENU submenu

Function Description

Information

Displays the UPS information.

Configure

Displays the UPS settings that can be configured by the user.

Event Log

Displays the 3 most recent events, by event count, time

(day/hour/minute), and event description.

LCD INFORMATION READOUT

There are 19 types of UPS information available for display.

1. Press the “ENTER” button to activate the “MAIN MENU”.

2. Press the “▲” and “▼” buttons to scroll to the “Information” option.

3. Press the “ENTER” button to select the “Information” submenu.

4. Press the “▲” and “▼” buttons to scroll through the “Information” submenu in the following table.

5. Press the “ESC” button to return to UPS Status.

Information Submenu

Description

O/P Volt = XXX.XV

Displays the Output Voltage

O/P Freq = XX.XHz

Displays the Output Frequency

I/P Volt = XXX.XV

Displays the Input Voltage

I/P Freq = XX.XHz

Displays the Input Frequency

O/P Load = XXX%

Displays the Output Load as a Percentage of Maximum load

O/P Amp = X.XA

Displays the Output Current

O/P Watt =XXXXXW

Displays the Output Wattage

O/P VA =XXXXXVA

Displays the Output VA

BAT Volt = XXX.XV

Displays the Battery Voltage

BAT Cap = XXX%

Displays the Estimated Percentage of Battery Capacity

BAT Runtime =XXXM

Displays the Estimated Battery Runtime in Minutes

EBM Number = X

Displays the External Battery Module Number

TEMP =XX°C / XXX°F

Displays the Approximate inside Temperature in both ℃ (Celsius) and ℉

(Fahrenheit) for the UPS

SBM = XXXXX XH(M)

Displays the stage of Smart Battery Management with Operation Time

Rating = XXK VA

Displays the UPS Rating

MCU Ver = XXXX

Displays the MCU Firmware Version

Model Name

Displays the UPS Model Name

Date & Time

- - - - / - - / - - - -:- -

Displays the present Date & Time

Next BAT Change

XXX / XXXX

Displays the next Battery Change Date & Time

LCD SETUP FUNCTIONS

LCD EVENT LOG

3 Event Logs of UPS can be recorded.

1. Press the “ENTER” button to activate the “MAIN MENU”.

2. Press the “▲” and “▼” buttons to scroll to the “Event Log” option.

3. Press the “ENTER” button to select the “Event Log” submenu.

4. Press the “▲” and “▼” buttons to scroll through the “Event Log” submenu in the following table.

5. Press the “ESC” button to return to UPS Status.

Event Log Submenu

Description

(X)

XXDXXHXXM (without PowerPanel® Business or RMCARD302)

- - / - - - -:- - (with PowerPanel® Business or RMCARD302)

Event Content

MULTI-LANGUAGE INTERFACE

Users can configure 1 of the 4 available languages for display.

([English], [Español-Spanish], [Français-French], [Deutsch-German])

1. Press the “ENTER” button to activate the “MAIN MENU”.

2. Press the “▲” and “▼” buttons to scroll to the “Configure” option.

3. Press the “ENTER” button to select the “Configure” submenu.

4. Press the “▲” and “▼” buttons to scroll through the “Language” options.

5. Press the “ENTER” button to select the “Language” submenu.

6. Press the “▲” and “▼” buttons to scroll to the language that you want to select.

You may be prompted to save the selection, if so press the “ENTER” button to save the setting.

7. Press the “ESC” button to cancel or return to previous LCD menu.

LCD SETTINGS CONFIGURATION

There are 22 UPS settings that can be configured by the user.

1. Press the “ENTER” button to activate the “MAIN MENU”.

2. Press the “▲” and “▼” buttons to scroll to the “Configure” option.

3. Press the “ENTER” button to select the “Configure” submenu.

4. Press the “▲” and “▼” buttons to scroll to the “Configure” submenu in the following table.

5. Press the “ENTER” button to select the setting you want to configure.

The first configuration parameter will be displayed on the second column of LCD screen.

6. Press the “▲” and “▼” buttons to scroll through the different parameters.

7. Press the “ENTER” button to select the parameter you want to change.

You may be prompted to save the selection, if so press the “ENTER” button to save the setting. Some options are saved

and started automatically. (See the following table for additional details.)

8. Press the “ESC” button to cancel or return to the previous LCD menu.

LCD SETUP FUNCTIONS

Configure Submenu

Available Settings

Default Setting

Output Voltage*

= [100V] [110V] [115V] [120V] [125V]

120V

Sync Freq Window

Range= [+/- 1%] [+/- 2%] [+/- 3%] [+/- 4%] [+/- 5%]

[+/- 6%] [+/- 7%] [+/- 8%] [+/- 9%] [+/-10%]

+/- 5%

Bypass V Window

Range= [+10%/-10%] [+10%/-15%] [+10%/-20%]

[+15%/-10%] [+15%/-15%] [+15%/-20%]

+10%/-15%

Bypass Condition

[Check Freq/Volt] [Check Volt Only] [No Bypass]

Check Freq/Volt

ECO Mode**

[Disable] [Enable]

Disable

[V Range= +/-15%] [V Range= +/-10%] (for [Enable])

V Range= +/-10%

Manual Bypass

[Disable] [Enable]

Disable

Battery Test

[Activate?]

None

Audible Alarms

[Disable] [Enable]

Enable

EBM Number

= [0] [1] [2] [3] [4] [5] [6] [7] [8] [9] [10]

Wiring Fault

[Disable] [Enable]

Disable

NCL Control

[Outlet On] [Outlet Off]

Outlet On

Language

[English] [Español-Spanish] [Français-French] [Deutsch-German]

English

Generator Mode***

[Disable] [Enable]

Disable

Communication

[Disable] [Enable]

Enable

Dry Relay Set

[I/P Power Fail] [Battery Low] [Summary Alarm]

[UPS On Bypass] [UPS Fail]

I/P Power Fail

Converter Mode****

[Converter Off] [O/P Freq = 50Hz] [O/P Freq = 60Hz]

Converter OFF

Screen Saver

[Disable] [1 Minutes] [5 Minutes]

5 minutes

Clear Event Log

[Activate?]

None

Button OFF LOCK

[Disable] [Enable]

Disable

Charger Function

[SBM] [Constant]

SBM

Signal Inputs

[Disable] [EPO] [ROO]

Disable

Charger Check

[Disable] [Enable]

Disable

*) 100V are derated by 20%, 110 V are derated by 10%

Output voltage default setting depends on different nation or order requested.

**) This function can’t be set when Manual Bypass, Generator Mode or Converter Mode is enabled.

***) UPS has no bypass when Generator Mode is enabled.

****) UPS has no bypass when Converter Mode is enabled. This function can only be set before the UPS is on.

LCD SETUP FUNCTIONS

SILENCING AUDIBLE ALARMS

1. Press any of four function buttons on the LCD module; Note: the alarm can not be turned off for a “Battery Low”

condition. This condition will still result in an audible alarm.

2. Change the 'Audible Alarms' option to 'Disable' in the LCD screen and it will no long give an audible alarm for any

malfunction.

MANUAL BATTERY TEST

Select 'Active' in the 'Battery Test' portion of the LCD screen and the unit will perform a manual battery test.

GRAPHICAL LOAD/BATTERY CAPACITY DISPLAY

1. Press the “ESC” button to return to UPS Status.

2. Press the “▲” and “▼” buttons to scroll to the “LOAD“ and “BAT“ Capacity.

3. Press the “▲” and “▼” buttons to scroll to the “Charging” or “Discharging” Capacity.

Discharging Capacity

The LCD screen displays the remaining battery

capacity with a graphical icon while on Battery Mode.

Charging Capacity

The LCD screen displays the battery capacity during

charging with a graphical icon while on Line Mode.

LOAD and BAT Capacity

The LCD screen displays the Load and Battery

capacity with a graphical icon.

LCD MODULE REMOTE CONTROL and WALL-MOUNTING INSTRUCTIONS

REMOTE CONTROL

Step 1: Remove the Multifunction LCD Module

Unscrew the right panel of the UPS. Separate the right panel from the

UPS. Gently lift the LCD module out. Reinstall the right panel.

Step 2: Connect the DB26 Cable

Connect the DB26 cable from LCD module to the “Remote Control

Port” on the front panel as shown in the following figure.

WALL-MOUNTING INSTRUCTIONS

Step 1: Remove the Multifunction LCD Module

Unscrew the right panel of the UPS. Separate the right panel from the

UPS. Gently lift the LCD module out. Reinstall the right panel.

Step 2: Rotate the DB26 Connector of LCD Module

Step 3: Connect the DB26 Cable

Connect the DB26 cable from LCD module to the “Remote Control

Port” on the front panel as shown in the following figure.

Step 4: Mount LCD Module on the Wall

SAFETY PRECAUTIONS

CAUTION! It must be done by qualified personnel.

CAUTION! To avoid electric shock, turn off and unplug the unit before installing REMOTE CONTROL or WALL-MOUNTING INSTRUCTIONS.

MAINTENANCE

Storage

To store your UPS for an extended period, cover it and store with the

battery fully charged. Recharge the battery every three months to ensure

battery life.

Battery Replacement

Please read and follow the Safety Instructions before servicing the

battery. Battery replacement should be performed by trained personnel

who are familiar with the procedures and safety precautions. Make a note

of the replacement Battery tray number.

Safety Precautions

CAUTION! Only use replacement batteries which are certified by

CyberPower Systems. Use of incorrect battery type is an electrical

hazard that could lead to explosion, fire, electric shock, or short circuit.

CAUTION! Batteries contain an electrical charge that can cause

severe burns. Before servicing batteries, please remove any conductive

materials such as jewelry, chains, wrist watches, and rings.

CAUTION! Do not open or mutilate the batteries. Electrolyte fluid is

harmful to the skin/eyes and may be toxic.

CAUTION! To avoid electric shock, turn off and unplug the UPS from

the wall receptacle before servicing the battery.

CAUTION! Only use tools with insulated handles. Do not lay tools or

metal parts on top of the UPS or battery terminals.

Replacement Batteries

Please refer to the front side of the UPS for the model number of the

correct replacement batteries. For battery procurement, log onto

www.CPSww.com, or contact your local dealer.

Battery Disposal

Batteries are considered hazardous waste and must be disposed of

properly. Contact your local government for more information about

proper disposal and recycling of batteries. Do not dispose of batteries

in fire.

CyberPower Systems encourages environmentally sound methods for

disposal and recycling of its UPS products.

Please dispose and/or recycle your UPS and batteries in accordance to

the local regulations of your state.

Battery Installation

Step 1: Remove the front panels

Step 2: Remove the retaining screws from

the cable protection cover and then remove

the cover itself

Step 3: Unscrew the connectors fixed plates

on the battery retaining cover

Step 4: Pull the battery tray out slowly and

then put the new battery tray back into the

compartment

Step 5: Fasten back the connectors on the

battery retaining cover. Then insert the

battery connectors and tighten the screws

of battery retaining cover

Step 6: Install the front panels

TECHNICAL SPECIFICATIONS

*)100V are derated by 20%, 110 V are derated by 10%

Model

OL1000XL

OL1500XL

OL2200XL

OL3000XL

Configuration

Capacity (VA)

1000VA

1500VA

2200VA

3000VA

Capacity (Watts)

900W

1350W

1800W

2700W

Form Factor

Tower

Energy-saving Technology

Yes, ECO Mode Efficiency > 93%

Input

Input Voltage Range

100~125Vac

Input Frequency Range

50 / 60Hz

Input Power Factor

0.99

Cold Start

Yes

Output

Output Waveform

Sine wave

Output Voltage*

100, 110, 115, 120, 125Vac (Configurable) ±2%

Output Frequency

50 / 60Hz (Auto-Sensing or Configurable) ±0.25Hz

Transfer Time (Typically)

0ms

Rated Power Factor

0.9

0.82

0.9

Harmonic Distortion

THD < 3% at Linear Load, < 5% at Non-linear Load

Crest Factor

3 : 1

ECO Mode Voltage Regulation

±10%, ±15% (Configurable)

UPS Outlets

(9) NEMA 5-15R

(6) NEMA 5-20R,

(1) L5-20R

(6) NEMA 5-20R,

(1) L5-30R

Protection

Surge Protection

IEC 61000-4-5 Level 3

Phone / Network Protection

RJ11/RJ45 (One In/One Out)

Overload Protection

Line Mode： 105~125% Load for 1 min, 126~150% Load for 10 sec

Battery Mode： 105~130% Load for 10 sec, 131~150% Load for 2 sec

Short Circuit Protection

UPS Output Cut off Immediately or Input Fuse / Circuit Breaker Protection

Battery

Specifications

(3) 12V/9AH

(6) 12V/9AH

Recharge Time (Typically)

5 hours

Sealed, Maintenance Free

Yes

Hot-Swappable

Yes

Status Indicators

LCD Screen

Multi-Function LCD Readout that Supports：

Multi-Language Interface, (19) Types of Read Out,

(22) Types of Function Setting, (3) Event Logs

LED Indicators

Power On (White), Line Mode (Green), Battery Mode (Yellow),

Bypass Mode (Yellow), Fault (Red), Replace Battery (Red)

Audible Alarms

Battery Mode, Battery Low, Overload, UPS Fault, Replace Battery

Environment

Operating Temperature

32℉ to 104℉ ( 0℃ to 40℃)

Operating Relative Humidity

0 to 90% Non-Condensing

Management

On-Device Features

Self Test, Auto-Charge, Auto-Restart, Auto-Overload Recovery

Connectivity Ports

(1) Serial Port (RS232), (1) USB Port, (1) Relay Out

SNMP/HTTP Capable

(1) Expansion Port (With optional SNMP card)

Software

Power Management Software

PowerPanel

Business Edition

Physical

Dimensions

15.6 x 6.6 x 9.1in. (397 x 167 x 232mm)

16.3 x 8.3 x 13.2in. (414 x 212 x 336mm)

Net Weight

34.1lbs(15.5Kg)

66.0lbs(30.0Kg)

Safety

Conformance Approvals

UL, VCCI, BSMI

TROUBLE SHOOTING

Problem

Possible Cause

Solution

Warning

O/P Overload

Your equipment requires more power than the

UPS can provide. If the UPS is in Line Mode

then it will transfer to Bypass Mode; if the UPS is

in Battery Mode it will shutdown.

Shut off non-essential equipment. If this solves

the overload problem, the UPS will transfer to

normal operation.

Load Over XXX%

Your equipment requires more power than the

setting in the Power Management Software

(PowerPanel

Business) will allow.

Shut off the non-essential equipment or increase

the level in the Power Management Software.

Battery Mode

UPS is operating on battery power.

Save your data and perform a controlled-

shutdown.

Battery Low

UPS is operating on battery power and will be

shutting down soon due to extremely low battery

voltage.

UPS will restart automatically when acceptable

utility power returns.

BAT Disconnected

Missing battery power.

Check battery connector and battery breaker.

Battery Failure

UPS has failed a Battery Test.

1. Check battery connector and battery breaker.

2. Contact technical support to replace the

battery.

Replace Battery

Battery will soon need to be replaced due to

insufficient runtime.

Contact technical support to replace the battery.

EPO OFF

Missing the EPO connection.

Check the EPO connection.

Wiring Fault

Line and neutral wires are reversed.

Exchange line and neutral wires.

Missing ground wire.

Connect ground wire.

No ground wire.

Disable Wiring Fault alarm on LCD panel.

Line Abnormal

Wrong utility power backed up during UPS auto-

restart.

Check whether voltage or frequency of utility

power is out of range.

Output Short

Output short circuit.

Your attached equipment may have problems,

please remove them and check again.

Over Temperature

High ambient temperature.

Check the fan for operation and if the ventilation

hole has been covered.

Coldstart Lock

UPS is locked to prevent consuming battery

power during shipping.

Plug into utility power for first-time operation.

Autorestart Lock

“Automatic Restore” is disabled in Power

Management Software (PowerPanel

Business)

Press “ON/OFF“ button to turn on UPS

Fault

Over Charge

Battery is overcharged.

1. Remove battery connector and check

charger voltage.

2. Contact CyberPower for repair.

Charger Failure

Charger has failed.

High O/P V

Output voltage is too high.

1. Shut down UPS and turn off input breaker.

2. Contact CyberPower for repair.

Low O/P V

Output voltage is too low.

Bus Fault

Internal DC bus voltage is too high or too low.

Fan Error

Internal Fan has failed.

CyberPower Systems Inc.

www.cpsww.com

Entire contents copyright

without permission is prohibited. PowerPanel

Business Edition and PowerPanel

Personal Edition are trademarks of

CyberPower Systems Inc.

CyberPower OL3000XL ユーザーマニュアル

ブランド: CyberPower

モデル: OL3000XL

カテゴリー: 無停電電源装置（UPS）

タイプ: ユーザーマニュアル

このマニュアルも適しています

PDFをダウンロードします

報告

他の言語で

English: CyberPower OL3000XL User manual

CyberPower OL3000XL ユーザーマニュアル

このマニュアルも適しています

CyberPower OL3000XL ユーザーマニュアル

他の言語で

その他のドキュメント