Samsung HT-J5550WK ユーザーマニュアル

5.1CH Blu-ray™

Home Entertainment System

User manual

HT-J5500K

HT-J5530K

HT-J5550K

HT-J5550WK

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register your product at

www.samsung.com/register

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 1 2015/3/12 15:33:45

2 - English

Safety Information

~

The slots and openings in the cabinet and in the back

or bottom are provided for necessary ventilation. To

ensure reliable operation of this apparatus, and to

protect it from overheating, these slots and openings

must never be blocked or covered.

- Do not place this apparatus in a confined space,

such as a bookcase, or built-in cabinet, unless

proper ventilation is provided.

- Do not place this apparatus near or over a radiator

or heat register, or where it is exposed to direct

sunlight.

- Do not place vessels (vases etc.) containing water

on this apparatus. A water spill can cause a fire or

electric shock.

~

Do not expose this apparatus to rain or place it near

water (near a bathtub, washbowl, kitchen sink, or

laundry tub, in a wet basement, or near a swimming

pool, etc.). If this apparatus accidentally gets wet,

unplug it and contact an authorized dealer immediately.

~

This apparatus uses batteries. In your community,

there might be environmental regulations that require

you to dispose of these batteries properly. Please

contact your local authorities for disposal or recycling

information.

~

Do not overload wall outlets, extension cords or

adaptors beyond their capacity, since this can result in

fire or electric shock.

~

Route power-supply cords so that they are not likely to

be walked on or pinched by items placed on or against

them. Pay particular attention to cords at the plug end,

at wall outlets, and the point where they exit from the

apparatus.

~

To protect this apparatus from a lightning storm, or

when it is left unattended and unused for long periods

of time, unplug it from the wall outlet and disconnect

the antenna or cable system. This will prevent damage

to the set due to lightning and power line surges.

~

Before connecting the AC power cord to the DC

adaptor outlet, make sure the voltage designation of

the DC adaptor corresponds to the local electrical

supply.

~

Never insert anything metallic into the open parts

of this apparatus. Doing so may create a danger of

electric shock.

~

To avoid electric shock, never touch the inside of this

apparatus. Only a qualified technician should open this

apparatus.

~

Make sure to plug the power cord in until it is firmly

seated. When unplugging the power cord from a wall

outlet, always pull on the power cord's plug. Never

unplug by pulling on the power cord. Do not touch the

power cord with wet hands.

~

If this apparatus does not operate normally - in

particular, if there are any unusual sounds or smells

coming from it - unplug it immediately and contact an

authorized dealer or service center.

~

Maintenance of Cabinet.

- Before connecting other components to this

product, be sure to turn them off.

- If you move your product suddenly from a cold place

to a warm place, condensation may occur on the

operating parts and lens and cause abnormal disc

playback. If this occurs, unplug the product, wait for

two hours, and then connect the plug to the power

outlet. Then, insert the disc, and try to play back

again.

~

Be sure to pull the power plug out of the outlet if the

product is to remain unused or if you are leaving the

house for an extended period of time (especially when

children, elderly, or disabled people will be left alone in

the house).

- Accumulated dust can cause an electric shock, an

electric leakage, or a fire by causing the power cord

to generate sparks and heat or the insulation to

deteriorate.

~

Contact an authorized service center for information

if you intend to install your product in a location with

heavy dust, high or low temperatures, high humidity,

chemical substances, or where it will operate 24 hours

a day such as in an airport, a train station, etc. Failing

to do so may lead to serious damage of your product.

~

Use only a properly grounded plug and wall outlet.

- An improper ground may cause electric shock or

equipment damage. (Class l Equipment only.)

~

To turn this apparatus off completely, you must

disconnect it from the wall outlet. Consequently, the

wall outlet and power plug must be readily accessible

at all times.

CAUTION

RISK OF ELECTRIC SHOCK. DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK). THERE ARE NO USER

SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO

QUALIFIED PERSONNEL.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that important

literature concerning operation and

maintenance has been included with

this product.

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 2 2015/3/12 15:33:45

3 - English

Safety Information

~

Do not allow children to hang on the product.

~

Store the accessories (battery, etc.) in a location safely

out of the reach of children.

~

Do not install the product in an unstable location such

as a shaky self, a slanted floor, or a location exposed

to vibration.

~

Do not drop or strike the product. If the product is

damaged, disconnect the power cord and contact a

service center.

~

To clean this apparatus, unplug the power cord from

the wall outlet and wipe the product using a soft,

dry cloth. Do not use any chemicals such as wax,

benzene, alcohol, thinners, insecticide, air fresheners,

lubricants, or detergent. These chemicals can damage

the appearance of the product or erase the printing on

the product.

~

Do not expose this apparatus to dripping or splashing.

Do not put objects filled with liquids, such as vases on

the apparatus.

~

Do not dispose of batteries in a fire.

~

Do not plug multiple electric devices into the same wall

socket. Overloading a socket can cause it to overheat,

resulting in a fire.

~

There is danger of an explosion if you replace the

batteries used in the remote with the wrong type of

battery. Replace only with the same or equivalent type.

WARNING :

~

TO PREVENT THE SPREAD OF FIRE,

KEEP CANDLES AND OTHER ITEMS

WITH OPEN FLAMES AWAY FROM

THIS PRODUCT AT ALL TIMES.

~

To reduce the risk of fire or electric

shock, do not expose this appliance to rain or

moisture.

CLASS 1 LASER PRODUCT

This product is classified as a CLASS 1 LASER product.

Use of controls, adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

Complies with 21CFR 1040.10 except for deviations

pursuant to Laser Notice No. 50, dated June 24, 2007.

CAUTION :

~

INVISIBLE LASER RADIATION WHEN OPEN AND

INTERLOCKS DEFEATED, AVOID EXPOSURE TO

BEAM.

CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

LUOKAN 1 LASER LAITE

KLASS 1 LASER APPARAT

PRODUCTO LÁSER CLASE 1

3D Precautions

IMPORTANT HEALTH AND SAFETY INFORMATION FOR

3D PICTURES.

Read and understand the following safety information

before using the 3D function.

~

Some viewers may experience discomfort while viewing

3D TV such as dizziness, nausea, and headaches.

If you experience any such symptom, stop viewing 3D

TV, remove the 3D Active Glasses, and rest.

~

Watching 3D images for an extended period of time

may cause eye strain. If you feel eye strain, stop

viewing 3D TV, remove your 3D Active Glasses, and

rest.

~

A responsible adult should frequently check on children

who are using the 3D function.

If there are any reports of tired eyes, headaches,

dizziness, or nausea, have the child stop viewing 3D

TV and rest.

~

Do not use the 3D Active Glasses for other purposes

(such as general eyeglasses, sunglasses, protective

goggles, etc.)

~

Do not use the 3D function or 3D Active Glasses while

walking or moving around. Using the 3D function or 3D

Active Glasses while moving around may cause you to

bump into objects, trip, and/or fall, and cause serious

injury.

~

If you want to enjoy 3D content, connect a 3D device

(3D compliant AV receiver or TV) to the product’s HDMI

OUT port using a high-speed HDMI cable. Put on 3D

glasses before playing the 3D content.

~

The product outputs 3D signals only through an HDMI

cable connected to the HDMI OUT port.

~

The video resolution in 3D play mode is limited to the

resolution of the original 3D video. You cannot change

the resolution to your preference.

~

Some functions such as BD Wise, screen size

adjustment, and resolution adjustment may not operate

properly in 3D play mode.

~

You must use a high-speed HDMI cable for proper

output of the 3D signal.

~

Stay at least three times the width of the screen from

the TV when watching 3D images. For example, if

you have a 46 inch screen, stay 3.5 meters from the

screen.

~

Place the 3D video screen at eye level for the best 3D

picture.

~

When the product is connected to some 3D devices,

the 3D effect may not function properly.

~

This product does not convert 2D content into 3D.

~

“Blu-ray 3D” and “Blu-ray 3D” logo are trademarks of

the Blu-ray Disc Association.

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 3 2015/3/12 15:33:46

4 - English

Contents

GETTING STARTED

4 Accessories

5 Speaker Components

7 Front Panel

7 Rear Panel

8 Remote Control

CONNECTIONS

9 Connecting the Speakers

13 Connecting to a TV and External Devices

14 Connecting to a Network Router

SETTINGS

15 The Initial Settings Procedure

16 The Home Screen at a Glance

16 Accessing the Settings Screen

17 Settings Menu Functions

20 Radio Setup

21 Network Setup

24 Wi-Fi Direct

25 Upgrading Software

26 Setting Up DLNA

PLAYING CONTENT

27 Switching the Source Device

27 Playing Commercial Discs

27 Playing a Disc with User Recorded Content

28 Playing Files on a USB Device

29 Controlling Video Playback

31 Playing a Pre-Recorded Commercial Audio Disc

31 Controlling Music Playback

33 Playing Photo Content

33 Using Karaoke

34 Using Bluetooth

35 Using the Special Effects Remote Control

Buttons

NETWORK SERVICES

37 Using BD-LIVE™

37 Using DLNA

37 Apps

38 Using Opera TV Store

39 Screen Mirroring

APPENDIX

40 Additional Information

41 Disk and Format Compatibility

46 Troubleshooting

49 Specifications

51 Licenses

Check the box for the accessories and speaker

components listed or shown below.

Accessories

Power Cable

FM Antenna

HDMI Cable

`

Figures and illustrations in this User Manual

are provided for reference only and may

differ from actual product appearance.

~

Remote Control

~

User Manual

~

Batteries (AAA size)

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 4 2015/3/12 15:33:47

5 - English

Getting Started

Speaker Components

HT-J5500K

Front x 2 Surround x 2

Center

Subwoofer Speaker Cable x 6

HT-J5530K

HT-J5550K

Getting Started

Screw (5x15) x 4

Center Screw (5x20) x 16 Speaker Cable x 6

Front x 2 Stand x 4 Stand Base x 4 Surround x 2 Subwoofer

Screw (5x15) x 2

Center Screw (5x20) x 8 Speaker Cable x 6

Front x 2 Stand x 2 Stand Base x 2 Surround x 2 Subwoofer

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 5 2015/3/12 15:33:48

6 - English

Getting Started

HT-J5550WK

Screw (5x15) x 4

Front x 2 Screw (5x20) x 16 Centre Stand Base x 4

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

ID SET

L

R

Surround x 2 Stand x 4 Subwoofer Speaker Cable x 6

Wireless Receiver

Module (SWA-7000)

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 6 2015/3/12 15:33:50

7 - English

Connections

Front Panel

MIC JACK

DISPLAY ICONS

5V 0.5A

MIC 2MIC 1

FUNCTION

5V 0.5A

MIC 2MIC 1

STOP

5V 0.5A

MIC 2MIC 1

PLAY/PAUSE

5V 0.5A

MIC 2MIC 1

OPEN/

CLOSE

5V 0.5A

MIC 2MIC 1

VOLUME

CONTROL

5V 0.5A

MIC 2MIC 1

POWER

5V 0.5A

MIC 2MIC 1

USBREMOTE CONTROL SENSOR

DISPLAY

DISC TRAY



When the product is on, do not let children touch the product's surface. It will be hot.



To upgrade the product's software through the USB jack, you must use a USB flash drive.



When the product displays a Blu-ray Disc menu, you cannot start the movie by pressing the

5V 0.5A

MIC 2MIC 1

/

6

button

on the product or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and

then press the

v

button.



If you are using the Internet or are playing content from a USB device on your TV through the home theater,

you cannot select the BD/DVD mode with the FUNCTION button. To select the BD/DVD mode, exit the

Internet or stop the content you are playing on the TV, and then select the BD/DVD mode.



Plug the microphone jack before using Karaoke function.

Rear Panel

* Connecting the FM Antenna

1. Connect the supplied FM antenna to the FM ANT Jack.

2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a

wall or other rigid surface.



Maintain a minimum of 10 cm of clear space on all sides of the home theater to ensure adequate ventilation.

Do not obstruct the cooling fan or ventilation holes.



This product does not receive AM broadcasts.

SURROUND

* In case of HT-J5500K/J5530K/J5550K

COOLING FAN

* FM ANTENNA

AUX IN

HDMI OUT

SPEAKER OUTPUT

CONNECTORS

(HT-J5550WK)

POWER CORD LAN TERMINALEXTERNAL DIGITAL

AUDIO IN (OPTICAL)

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 7 2015/3/12 15:33:51

8 - English

Getting Started

Remote Control

Tour of the Remote Control

Installing batteries in the Remote Control



Make sure to match the "+" and "–" ends of the batteries with

the diagram inside the compartment.



Assuming typical usage, the batteries last for about one year.



The remote control can be used up to approximately

7 meters from the product in a straight line.

Battery size: AAA

Turn the product on and off.

Adjust the volume.

Press numeric buttons to operate

options.

Press to skip backwards or forwards.

Press to use the karaoke function

(Mic. vol., Echo, Key Cotrol).

Press to move to the Home screen.

Select on-screen menu items

and change menu values.

Return to the previous menu.

These buttons are used both for

menus on the product and also

several Blu-ray Disc functions.

Press to view the disc menu.

Press to use the Tools menu.

Press to play a disc or files.

Press to direct the audio signal to

the home theater speakers or TV

speaker. (See page 35)

Select the desired DSP/EQ audio

mode.

Press to stop a disc or files.

Cut off the sound temporarily.

Press to search backwards or

forwards.

Press to pause playing.

Allows you to repeat a title,

chapter, track or disc.

Use to enter the Popup menu/

Title menu.

Select MONO or STEREO for radio

broadcasts.

Search for active FM stations and

to change channels.

Use to display the playback

information when playing

a Blu-ray/DVD disc or files.

To open and close the disc tray.

Press to exit the menu.

Press to select Home Theater's

mode. (BD/DVD, D. IN, AUX,

etc.).

Use to set a preset radio frequency.

TOOLS

RETURN

EXIT

INFO

KARAOKE HOME

REPEAT

1

2

3

7

8 9

DISC MENU TITLE MENU

0

POPUP

4

5 6

MUTE

MO/ST

TUNER

MEMORY

DSP/EQTV SOUND

A B C D

TUNING

DOWN

UP

VOLUME

-

+

FUNCTION

Press to record FM radio broadcasts.

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 8 2015/3/12 15:33:51

9 - English

Getting Started

Connections

This section describes various methods of connecting the product to other external components.

Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

Connecting the Speakers

Surround (L)

Surround (R)

Product

Centre

Subwoofer

Wireless

Receiver Module

Front (L)

Front (R)

Position of the product

Place it on a stand or cabinet

shelf, or under the TV stand.

Selecting the Listening Position

The listening position should be

located about 2.5 to 3 times the

TV's screen size away from the

TV. For example, if you have a 46

inch screen, locate the listening

position

2.92 to 3.50 meters

from the screen.

* The Wireless Receiver Module applies to HT-J5550WK only.

Front Speakers

Place these speakers in front of your listening position, facing inwards (about

45°) toward you. Place the front speakers so that their tweeters will be at the

same height as your ear. Align the front face of the front speakers with the front

face of the centre speaker or place them slightly in front of the centre speakers.

Centre Speaker

It is best to install the centre speaker at the same height as the front speakers.

You can also install it directly over or under the TV.

Surround Speakers

Place these speakers to the side of your listening position. If there isn't enough

room, place these speakers so they face each other. Position them about 60 to

90cm above your ear, facing slightly downward.

* Unlike the front and centre speakers, the surround speakers are used mainly

for sound effects. Sound will not come from them all the time.

Subwoofer

The position of the subwoofer is not so critical. Place it anywhere you like.

* Surround speakers must be connected to the wireless receiver module. (HT-J5550WK only)

* The appearance of your speakers may differ from the illustrations in this manual.

* Each speaker has a coloured label on its back or underside. Each cable has a single coloured band

near its end. Match the band on each cable to the speaker label by colour, and then connect the

cable to the speaker. See page 10 for exact instructions.

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 9 2015/3/12 15:33:52

10 - English

Connections

Installing the Speakers on the Tallboy Stand

* HT-J5530K only - Front Speakers

HT-J5550K/J5550WK only - Front/Surround

Speakers

1. Turn the Stand Base upside-down and connect

it to the Stand.

2. Use the driver to fasten the screws (5x20) on the

4 marked holes.

3. Straighten the provided speaker cable and run it

through the center hole of the Stand Base.

4. Connect the upper Speaker to the assembled

Stand.

5. Insert a screw (5x15) and fasten it lockwise

through the hole on the rear of the speaker

using a screwdriver.

6. Arrange the speaker cable along the groove on

the rear side of the stand pole.

7. Connect the arranged speaker cables to the

port on the speaker’s rear side while matching

their colors.

8. This is the appearance after the speaker is

installed.

Follow this steps to install other speaker.

Speaker Cable Connections

1. Match each speaker cable bundle to the correct speaker by matching the colored band on each bundle to

the colored sticker on the bottom or back of each speaker.

2. Connect the speaker wire plugs from each speaker to the back of the product by matching the colored

band on each cable to the colors of the speaker jacks. When connecting, make sure to match label color

on the back of speaker.

2

4

1

3

Stand Base

Stand

Speaker

Stand

5

7

6

8

Or

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 10 2015/3/12 15:33:53

11 - English

Connections

In case of HT-J5530K

SURROUND

Front Speaker (R)

Subwoofer

Center Speaker

Surround

Speaker (L)

Front Speaker (L)

Surround

Speaker (R)

* Refer to page 5 for the speakers of HT-J5500K/J5550K.



If you place a speaker near your TV set, the screen color may be distorted because of the magnetic field.

| CAUTION |

\

If you want to install the speakers on the wall, fasten screws or nails (not provided) firmly to the wall wherever

you want to hang a speaker, and then, using the hole in the rear of each speaker, carefully hang each

speaker on a screw or nail.

\

Do not let children play with or near the speakers. They could get hurt if a speaker falls.

\

When connecting the speaker wires to the speakers, make sure that the polarity (+/ –) is correct.

\

Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands or alien

substances into the duct (hole) of the subwoofer speaker.

\

Do not hang the subwoofer on the wall by the duct (hole).

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 11 2015/3/12 15:33:53

12 - English

Connections

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

ID SET

L

R

Front Speaker (R)

Subwoofer

Centre Speaker

Wireless Receiver

Module

Surround

Speaker (L)

Front

Speaker (L)

Surround

Speaker (R)

* This product should be connected with the SWA-7000 only.



If you place a speaker near your TV set, the screen colour may be distorted because of the magnetic field.



Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too

close to the product, sound from the speakers may be disrupted because of interference.



If you use a device such as a microwave oven, wireless LAN Card, Bluetooth device, or any other device

near the product, sound from the speakers may be disrupted because of interference.



The maximum transmission distance from the product to the wireless receiver module is about 10m, but

may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the

product and the wireless receiver module, the system may not operate at all, because the radio waves

cannot penetrate metal.



If the product doesn't make a wireless connection, you need to run an ID Set between the product and

wireless receiver module. With the product turned off, press "0"



"1"



"3"



"5" on the remote control. Turn

on the wireless receiver module. Then, press and hold the "ID SET" button on the back of the wireless

receiver module for 5 seconds, and then turn the product on.

| CAUTION |

\

If you want to install the speakers on the wall, fasten screws or nails (not provided) firmly to the wall wherever

you want to hang a speaker, and then, using the hole in the rear of each speaker, carefully hang each

speaker on a screw or nail.

\

Do not let children play with or near the speakers. They could get hurt if a speaker falls.

\

When connecting the speaker wires to the speakers, make sure that the polarity (+/ –) is correct.

\

Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands or alien

substances into the duct (hole) of the subwoofer speaker.

\

Do not hang the subwoofer on the wall by the duct (hole).

\

The wireless receiving antenna is built into the wireless receiver module. Keep it away from water and

moisture.

\

For optimal listening performance, make sure that the area around the wireless receiver module location is

clear of any obstructions.

\

In 2-CH mode, you will hear no sound from the wireless surround speakers.

HT-J5550WK

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 12 2015/3/12 15:33:53

13 - English

Connections

Connecting to a TV and External Devices

OPTICAL OUT

AUDIO OUT

HDMI IN (ARC)

SURROUND

Method 1 Method 2

R

Red

W

White

External Devices

Connecting to a TV

Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV.

If the TV supports ARC, you can hear the audio from your TV through the home theater with only this cable

connected. See page 18 in this manual and the section on ARC in your TV's user's manual for details.

Connecting to External Devices

Two methods of connecting external devices to your home theater are explained below.

Method 1 AUX IN : Connecting an External Analog Component

Using an RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out jack on

the external analog component.



Select the AUX mode.

~

Be sure to match the colors on the cable plugs to the colors on the input and output jacks.

Method 2 OPTICAL : Connecting an External Digital Audio Component

Use to connect the digital audio output of digital signal components such as Cable Boxes and Satellite

Receivers (Set-Top-Boxes) to the home theater. Using a digital optical cable (not supplied), connect the Optical

Digital Audio In jack on the product to the Digital Optical Out jack of the external digital device using a digital

optical cable.



Select the D. IN mode.



To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV.



This system supports Digital sampling frequencies of 32 kHz or higher from external digital components.



This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported.

Selecting an External Device to Use

To select an external device after you have connected it, press the FUNCTION button. Each time you press the

button, the mode changes in this order : BD/DVD

;

D. IN

;

AUX

;

FM

;

BT

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 13 2015/3/12 15:33:54

14 - English

Connections

Connecting to a Network Router

You can connect your product to your network router

using one of the methods illustrated below.

Wired Network

Broadband

service

Broadband

service

Broadband modem

(with integrated router)

Broadband

modem

Router

Or

SURROUND



Your router or your Internet Service Provider's

policies may prevent the product from accessing

Samsung's software update server. If this occurs,

contact your Internet Service Provider (ISP) for

more information.



DSL users, please use a router to make a network

connection.



Try to use the CAT 7 cable to connect.



You cannot use the product if the network speed

is slower than 10Mbps.



To use the DLNA function, you must connect your

PC to your network as shown in the illustrations

above.

The connection can be wired or wireless.

Wireless Network

Broadband

service

Wireless IP sharer



If your wireless IP router supports DHCP, this

product can use a DHCP or static IP address to

connect to the wireless network.



Set your wireless IP router to Infrastructure mode.

Ad-hoc mode is not supported.



The product supports only the following wireless

security key protocols:

- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES),

WPA2-PSK (TKIP/AES)



Select a channel on the wireless IP router that is

not currently being used. If the channel set for

the wireless IP router is currently being used by

another device nearby, it will result in interference

and communication failure.



In compliance with the newest Wi-Fi certification

specifications, Samsung home theaters do not

support WEP, TKIP, or TKIP-AES (WPS2 Mixed)

security encryption in networks running in the

802.11n mode.



Wireless LAN, by its nature, may cause

interference, depending on the operating

conditions (AP performance, distance, obstacles,

interference by other radio devices, etc.).

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 14 2015/3/12 15:33:54

15 - English

Settings

The Initial Settings Procedure

~

The Home menu will not appear if you do not

configure the initial settings.

~

The OSD (On Screen Display) may change in

this product after you upgrade the software

version.

~

The access steps may differ depending on the

menu you selected.

1. Turn on your TV after connecting the product,

and then turn on the product. When you turn

on the product for the first time, the product

automatically displays the Setup Language

screen.

2. Press the ▲▼ buttons to select the desired

language, and then press the

v

button.

3. Press the

v

button to start function setup.

Setup

TV Aspect and Network will be set.

Each setting may be changed later under "Settings"

a

Select

Start

4. The TV Aspect Ratio screen appears. Press

the ▲▼ buttons to select a TV aspect ratio, and

then press the

v

button.

You have four choices:

16:9 Original - For widescreen TVs. Displays

widescreen pictures in their original 16:9 format

and 4:3 pictures (the old, standard format) in 4:3

pillar box format with black bars on the left and

right.

16:9 Full - For widescreen TVs. Displays

widescreen pictures in their original 16:9 format

and expands 4:3 pictures to fill the 16:9 screen.

4:3 Letter Box - For older, standard screen,

analog TVs. Displays 4:3 pictures in full screen

and 16:9 pictures in letter box format that retains

the 16:9 aspect ratio but puts black bars above

and below the picture.

4:3 Pan-Scan - For older, standard screen,

analog TVs. Displays 4:3 pictures in full screen

and 16:9 pictures in Pan-Scan format that fills

the screen, but cuts off the left and right sides of

the picture and enlarges the middle vertically.

5. The Network screen appears.

- Before you begin, confirm that the product is

connected to your router.

- Set to wired or wireless depending on your

network environment.

- If your wireless network has a security code,

you will need to enter the code to complete

the network connection.

- If you have a network with static IP addresses,

we suggest you select Skip by pressing the

BLUE (D) button.



If you skip network setup here or the setup does

not work correctly, you can set up the product's

network connection later. (See page 21)

✓

Setup | Network

Select your network type.

Network Type

Network cable connected.

Wireless

Wired

Connect

a Previous d Skip m Move " Select

6. The product verifies the network connection

and then connects to the network. When it is

done, press the

v

button. The "Initial settings

completed." screen appears, and then the

Home screen appears.



If you want to display the Setup screen again

and make changes, select the Reset option. (See

page 20)



If you use an HDMI cable to connect the product

to an Anynet+ (HDMI-CEC)-compliant Samsung

TV and 1.) You have set the Anynet+ (HDMI-CEC)

feature to On in both the TV and the product and

2.) You have set the TV to a language supported

by the product, the product will select that

language as the preferred language automatically.

Settings

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 15 2015/3/12 15:33:55

16 - English

Settings

The Home Screen at a Glance

PLAY DISC

App 1 App 2 App 3 App 4

Screen

Mirroring

Change

Device

Function

No Disc

Settings

PHOTOS VIDEOS MUSIC

1

3 4 5 6 7 8 9

2

Opera TV

Store

More

1

PLAY DISC

The disc currently in the tray is displayed.

Press

v

to start playing the disc.

2

PHOTOS/VIDEOS/MUSIC

Play photos, videos, or music content from a

Disc, USB, PC, or mobile device.

3

Apps

Access various for pay or free-of-charge

applications.

4

Opera TV Store

Access the on-line Opera TV Store where you will

find high-quality video streaming, music streaming,

gaming, and social network apps.

5

More

A list of useful and popular apps we recommend.



The item may be not displayed depending on

different country.

6

Screen Mirroring

Set up the wireless mirroring function between the

home theater and a smart phone or tablet.

7

Change Device

Displays a list of external devices connected to the

main unit. Switch to the desired device.

8

Function

Use for switching to an external device, and

for radio and mode switching for a Bluetooth

connection. You can use the remote control’s

FUNCTION button and the main unit’s button

for mode switching.

9

Settings

Set various functions to suit your personal

preferences.



To play or view video, photo, or music files

located on your PC, you must connect your home

theater and PC to a home network and have

DLNA software installed on your PC. See page

26 and 37.

Accessing the Settings Screen

1. Select Settings on the Home screen, and then

press

v

. The Settings screen appears.

Settings

Picture

Sound

Network

System

Language

Security

General

Support

3D Settings

TV Aspect Ratio : 16:9 Original

BD Wise : Off

Resolution : Auto

Movie Frame (24Fs) : Off

HDMI Color Format : Auto

HDMI Deep Color : Off

Progressive Mode : Auto

2. To access the menus, sub-menus, and options

on the Settings screen, please refer to the

remote control illustration. (See page 17)



If you leave the product in the stop mode for more

than 5 minutes without using it, a screen saver

appears on your TV. If the product is left in the

screen saver mode for more than 20 minutes, the

power automatically turns off.

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 16 2015/3/12 15:33:56

17 - English

Settings

Buttons on the Remote Control Used

for the Settings Menu

TOOLS

RETURN

EXIT

INFO

KARAOKE HOME

REPEAT

1

2

3

7

8 9

DISC MENU TITLE MENU

0

POPUP

4

5 6

MUTE

MO/ST

TUNER

MEMORY

DSP/EQTV SOUND

A B C D

TUNING

DOWN

UP

VOLUME

-

+

FUNCTION

2 4

3

1

HOME Button : Press to move to the Home

screen.

2

RETURN Button : Press to return to the

previous menu.

3

v

(ENTER) / DIRECTION Button :

~

Press ▲▼◄► to move the cursor or

select an item.

~

Press the

v

button to activate the

currently selected item or confirm a

setting.

4

EXIT Button : Press to exit the current

menu.

Detailed Function Information

Each Settings function, menu item, and individual

option is explained in detail on-screen. To view an

explanation, use the ▲▼◄► buttons to select the

function, menu item, or option. The explanation will

usually appear on the bottom of the screen.

A short description of each Settings function starts

on this page. Additional information on some of the

functions is also in the Appendix of this manual.

Settings Menu Functions

Picture

3D Settings

Set up the 3D related functions.



3D Blu-ray Playback Mode: Select whether to

play a Blu-ray Disc with 3D contents in 3D Mode.

If you move to the Home menu while in 3D mode,

the product will switch to 2D automatically.



Screen Size:

Enter the size of the TV attached to the

product. The product will automatically adjust the 3D

output to the screen size of the TV.



Carefully read the health and safety information

before viewing 3D content. (See page 3)

TV Aspect Ratio

Lets you adjust the output of the product to the

screen size of your TV. (See page 40)

BD Wise

BD Wise is Samsung’s latest inter-connectivity

feature. When you connect a Samsung product

and a Samsung TV with BD Wise to each other

via HDMI, and BD Wise is on in both the product

and TV, the product outputs video at the video

resolution and frame rate of the Blu-ray/DVD Disc.

Resolution

Lets you set the output resolution of the HDMI

video signal to BD Wise, Auto, 1080p, 1080i,

720p, 576p/480p. The number indicates the

number of lines of video per frame. The i and

p indicate interlaced and progressive scan,

respectively. The more lines, the higher quality.

Movie Frame (24Fs)

Setting the Movie Frame (24Fs) feature to Auto lets

the product adjust its HDMI output to 24 frames per

second automatically for improved picture quality if

attached to a 24Fs compatible TV.

~

You can enjoy the Movie Frame (24Fs) feature

only on a TV supporting this frame rate.

~

Movie Frame is only available when the product

is in the HDMI 1080p output resolution modes.

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 17 2015/3/12 15:33:56

18 - English

Settings

HDMI Color Format

Lets you set the color space format for the HDMI

output to match the capabilities of the connected

device (TV, monitor, etc).

HDMI Deep Color

Lets you set the product to output video from

the HDMI OUT jack with Deep Color. Deep Color

provides more accurate color reproduction with

greater color depth.

Progressive Mode

Lets you improve picture quality when viewing

DVDs.

Sound

Karaoke Scoring

This feature rates your singing ability and gives you

a score for each song you sing.

My Karaoke

Set the volume of the vocals when using the

karaoke feature.



Original Vocals: Volume is set to the level of the

original sound.



Reduce Vocals: Volume is set to a level lower than

that of the original sound.

Speaker Settings

Lets you adjust the following speaker settings and

turn the speaker test on and off so you can test

the speakers.



Level

: Lets you adjust the relative loudness of

each speaker from 6dB to -6dB. For example, if

you like deep bass, you can increase the loudness

of the subwoofer by 6dB.



Distance

: Lets you adjust the relative distance

of each speaker from the listening position up to

9 meters. The farther the distance, the louder the

speaker will be.



Speaker Test

:

Lets you run the Speaker Test

function so you can test your adjustments. Setting

Speaker Test to On turns the Speaker Test on.

Setting it to Off turns it off.

Speaker Selection

Lets you select which speakers you want active,

either the TV's speakers or the home theater's

speakers.

Equalizer Mode

Set Equalizer Mode on to use the equalizer.

Equalizer Settings

Lets you set the equalizer.



Equalizer Settings only appears when

Equalizer Mode is On.

Audio Return Channel

Lets you direct the sound from the TV to the Home

Theater speakers. Requires an HDMI connection

and an Audio Return Channel (ARC) compatible

T V.

~

If Audio Return Channel is set to on and you

are using an HDMI cable to connect the product

to the TV, digital optical input will not work.

~

If Audio Return Channel is set to Auto and you

are using an HDMI cable to connect the product

to the TV, ARC or digital optical input is selected

automatically.

Digital Output

Lets you set the Digital Output to match the

capabilities of the AV receiver you’ve connected to

the product. For more details, please refer to the

digital output selection table. (See page 45)

Dynamic Range Control

Lets you apply dynamic range control to Dolby Digital,

Dolby Digital Plus, and Dolby TrueHD audio.



Auto:

Automatically controls the dynamic range of

Dolby TrueHD audio, based on information in the

Dolby TrueHD soundtrack. Also turns dynamic range

control off for Dolby Digital and Dolby Digital Plus.



Off: Leaves the dynamic range uncompressed,

letting you hear the original sound.



On: Turns dynamic range control on for all three

Dolby formats. Quieter sounds are made louder

and the volume of loud sounds is reduced.

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 18 2015/3/12 15:33:56

19 - English

Settings

Downmixing Mode

Lets you select the multi-channel downmix method

that is compatible with your stereo system. You can

choose to have the product downmix to Normal

Stereo or to Surround Compatible.

Audio Sync

When the product is attached to a digital TV, lets

you adjust the audio delay so that the audio syncs

with the video. You can set the delay between 0

and 300 milliseconds.

Network

Network Settings

Lets you configure the network connection so

you can enjoy various features such as Internet

services or DLNA Wi-Fi functionality, and perform

software upgrades.

Network Test

Lets you test the Internet Protocol setup to see if it

is working correctly.

Network Status

Lets you check the current network and Internet status.

Wi-Fi Direct

Lets you connect a Wi-Fi Direct device to the

product using a peer-to-peer network, without the

need for a wireless router.

Note that if the product is connected to a wireless

network, it may be disconnected when you use

Wi-Fi Direct. (

See page 24)



Text files, such as files with a .TXT or .DOC

extension, will not display when you are using the

Wi-Fi Direct function.

Screen Mirroring

The Screen Mirroring function lets you view the

screen of your smart phone or smart device on

the TV you have connected to the home theater

system. (

See page 39)

Device Name

Lets you assign an identifying name to the product.

You use this name to identify the product when you

are connecting external Wi-Fi devices (smart phones,

tablets, etc.) to it.

BD-Live Internet Connection

Lets you allow or prohibit an Internet connection

for the BD-Live service.

System

Setup

Lets you re-run the Setup procedure. (See page

15)

Quick Start

You can turn on the power quickly by decreasing

the boot time.



If this function is set to On, Standby power

consumption will be increased. (About 12W ~

20W)

Anynet+ (HDMI-CEC)

Anynet+ is a convenient function that offers linked

operations with other Samsung products that have

the Anynet+ feature and lets you control those

products with one Samsung TV remote. To operate

this function, you must connect this product to an

Anynet+ Samsung TV using an HDMI cable.

BD Data Management

Lets you manage the contents you downloaded

through a Blu-ray disc that supports the BD-Live

service. You can view information about the USB

device you are using for BD Live data storage

including the available storage space. You can also

delete BD Live data and change the device.

DivX® Video On Demand

View DivX® VOD Registration Codes to purchase

and play DivX® VOD contents.

Language

Lets you select the language you prefer for the On-

Screen Menu, Disc Menu, etc.

~

The selected language will only appear if it is

supported on the disc.

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 19 2015/3/12 15:33:56

20 - English

Settings

Security

The default PIN is 0000. Enter the default PIN to

access the security function if you haven't created

your own PIN.

BD Parental Rating

Prevents playback of Blu-ray Discs with a rating

equal to or above a specific age rating unless you

enter the PIN.

DVD Parental Rating

Prevents playback of DVDs with a rating above a

specific numerical rating unless you enter the PIN.

Change PIN

Changes the 4-digit PIN used to access security

functions.

General

Time Zone

Lets you specify the time zone that is applicable to

your area.

Support

Software Upgrade

For more information about this function, see page

25.

Contact Samsung

Provides contact information for assistance with

your product.

Terms of Service Agreement

View the general disclaimer regarding third party

contents and services.

Reset

Reverts all settings to their defaults except for the

network. Requires that you enter your security PIN.

The default security PIN is 0000.

Radio Setup

~

To listen to the radio, you must connect the

supplied FM antenna.

Operating the Radio with the Remote Control

1. Press the FUNCTION button to select FM.

2. Tune to the desired station.

~

Preset Tuning 1 : Press the

5

button to

select PRESET, and then press the TUNING

UP, DOWN button to select a preset station.

- Before you can tune to preset stations, you

must add preset stations to the product's

memory.

~

Manual Tuning : Press the

5

button to

select MANUAL, and then press the TUNING

UP, DOWN button to tune in to a lower or

higher frequency.

~

Automatic Tuning : Press the

5

button to

select MANUAL, and then press and hold

the TUNING UP, DOWN button for a few

seconds to automatically search the band.

Selecting Mono or Stereo

Press the MO/ST button.

~

Each time you press the button, the sound

switches between STEREO and MONO.

~

In a poor reception area, select MONO for a clear,

interference-free broadcast.

Presetting Stations

Example : Presetting FM 89.10 into memory.

1. Press the FUNCTION button to select FM.

2. Press the TUNING UP, DOWN button to scroll

the FM frequencies, and then select <89.10>.

3. Press the TUNER MEMORY button (the yellow

C button at the bottom of the remote).

4. Press the TUNER MEMORY button again

within about 5 seconds. The station is stored in

memory.



If you press the

TUNER MEMORY

button

repeatedly without changing the station, the

inputted station may be overwritten.

5. To preset another station, repeat steps 2 to 4.

~

To tune in to a preset station, press the

TUNING UP, DOWN button.

02831P-HT-J5500K_J5530K_J5550K(W)-ZK-ENG-0224.indd 20 2015/3/12 15:33:56

ページが読み込まれています...

Samsung HT-J5550WK ユーザーマニュアル

このマニュアルも適しています

Samsung HT-J5550WK ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント