HTS3562
HTS3582
Register your product and get support at
www.philips.com/welcome
1
English
EN
Contents
1 Important 2
Safety 2
Care for your product
3
Care of the environment
3
3D health warning
3
Help and support
3
2 Your home theater 4
Main unit 4
Connectors
4
Remote control
5
3 Connect and set up 6
Connect speakers 6
Connect to TV
7
Connect audio from TV and other devices
8
Set up speakers
9
Set up EasyLink (HDMI-CEC control)
9
Connect and set up a home network
10
4 Use your home theater 11
Access the home menu 11
Discs
11
Data fi les
13
USB storage devices
13
Audio, video, and picture options
14
Radio
15
MP3 player
15
Browse PC through DLNA
16
Karaoke
16
Choose sound
16
5 Change settings 17
Language settings 17
Picture and video settings
18
Audio settings
18
Parental control settings
18
Display settings
18
Energy saving settings
19
Speaker settings
19
Restore default settings
19
6 Update software 19
Check software version 19
Update software through USB
19
Update software through the Internet
20
7 Product specifi cations 20
8 Troubleshooting 23
9 Notice 24
Copyright 24
Compliance
24
Open source software
25
RMVB end user agreement (Asia Pacifi c
and China only)
25
Trademarks
25
10 Index 26
2 EN
1 Important
Read and understand all instructions before you
use your product. If damage is caused by failure to
follow instructions, the warranty does not apply.
Safety
Risk of electric shock or fi re!
• Never expose the product and accessories to
rain or water. Never place liquid containers,
such as vases, near the product. If liquids are
spilt on or into the product, disconnect it
from the power outlet immediately. Contact
Philips Consumer Care to have the product
checked before use.
• Never place the product and accessories
near naked fl ames or other heat sources,
including direct sunlight.
• Never insert objects into the ventilation slots
or other openings on the product.
• Where the mains plug or an appliance coupler
is used as the disconnect device, the disconnect
device shall remain readily operable.
• Disconnect the product from the power
outlet before lightning storms.
• When you disconnect the power cord, always
pull the plug, never the cable.
Risk of short circuit or fi re!
• Before you connect the product to the
power outlet, ensure that the power voltage
matches the value printed on the back or
bottom of the product. Never connect the
product to the power outlet if the voltage is
different.
Risk of injury or damage to the home theater!
• For wall-mountable products, use only the
supplied wall mount bracket. Secure the
wall mount to a wall that can support the
combined weight of the product and the wall
mount. Koninklijke Philips Electronics N.V. bears
no responsibility for improper wall mounting
that results in accident, injury or damage.
• For speakers with stands, use only the
supplied stands. Secure the stands to the
speakers tightly. Place the assembled stands
on fl at, level surfaces that can support the
combined weight of the speaker and stand.
• Never place the product or any objects on
power cords or on other electrical equipment.
• If the product is transported in temperatures
below 5°C, unpack the product and wait until
its temperature matches room temperature
before connecting it to the power outlet.
• Visible and invisible laser radiation when
open. Avoid exposure to beam.
• Do not touch the disc optical lens inside the
disc compartment.
• Parts of this product can be made of glass.
Handle with care to avoid injury and damage.
Risk of overheating!
• Never install this product in a confi ned space.
Always leave a space of at least four inches
around the product for ventilation. Ensure
curtains or other objects never cover the
ventilation slots on the product.
Risk of contamination!
• Do not mix batteries (old and new or carbon
and alkaine, etc.).
• Danger of explosion if batteries are
incorrectly replaced. Replace only with the
same or equivalent type.
• Remove batteries if they are exhausted or if
the remote control is not to be used for a
long time.
• Batteries contain chemical substances, they
should be disposed of properly.
Risk of swallowing batteries!
• The product/remote control may contain
a coin/button type battery, which can be
swallowed. Keep the battery out of reach of
children at all times! If swallowed, the battery
can cause serious injury or death. Severe
internal burns can occur within two hours of
ingestion.
• If you suspect that a battery has been
swallowed or placed inside any part of the
body, seek immediate medical attention.
• When you change the batteries, always
keep all new and used batteries out of
reach of children. Ensure that the battery
compartment is completely secure after you
replace the battery.
• If the battery compartment cannot be
completely secured, discontinue use of the
product. Keep out of reach of children and
contact the manufacturer.
3
English
EN
Care for your product
• Do not insert any objects other than discs
into the disc compartment.
• Do not insert warped or cracked discs into
the disc compartment.
• Remove discs from the disc compartment
if you are not using the product for an
extended period of time.
• Use only microfi ber cloth to clean the
product.
Care of the environment
Your product is designed and manufactured with
high quality materials and components, which can
be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC. Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and do not
dispose of your old products with your normal
household waste.
Correct disposal of your old product helps to
prevent potential negative consequences for the
environment and human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot be
disposed with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries because correct
disposal helps to prevent negative consequences
for the environmental and human health.
3D health warning
If you or your family has a history of epilepsy
or photosensitive seizures, consult a medical
professional before exposing yourself to fl ashing
light sources, rapid image sequences or 3D
viewing.
To avoid discomfort such as dizziness, headache or
disorientation, we recommend not watching 3D
for extended periods of time. If you experience
any discomfort, stop watching 3D and do not
immediately engage in any potentially hazardous
activity (for example driving a car) until your
symptoms have disappeared. If symptoms persist,
do not resume watching 3D without consulting a
medical professional fi rst.
Parents should monitor their children during 3D
viewing and ensure they do not experience any
discomfort as mentioned above. Watching 3D is
not recommended for children under six years of
age as their visual system is not fully developed yet.
Help and support
Philips provides extensive online support. Visit our
website at www.philips.com/support to:
• download the complete user manual
• print the quick start guide
• watch video tutorials (available only for
selected models)
• fi nd answers to frequently answered
questions (FAQs)
• email us a question
• chat with our support representative.
Follow the instructions on the website to select
your language, and then enter your product model
number.
Alternatively, you can contact Philips Consumer
Care in your country. Before you contact Philips,
note down the model number and serial number
of your product. You can fi nd this information on
the back or bottom of your product.
4 EN
2 Your home theater
Congratulations on your purchase, and welcome
to Philips! To fully benefi t from the support that
Philips offers, register your product at www.philips.
com/welcome.
Main unit
This section includes an overview of the main unit.
a Disc compartment
b Display panel
c ( Open/Close )
Open or close the disc compartment, or
eject the disc.
d ( Play/Pause )
Start, pause or resume play.
e SOURCE
Select an audio or video source for the home
theater.
f ( Standby-On )
Switch the home theater on or to standby.
Connectors
This section includes an overview of the
connectors available on your home theater.
Front connectors
a ( USB )
• Audio, video or picture input from a USB
storage device.
• Connect to a Wi-Fi dongle (Model:
Philips WUB1110, sold separately).
b MIC
Audio input from a microphone.
c MUSIC iLINK
Audio input from an MP3 player.
Rear connectors
a AC MAINS
Connect to the power supply.
b AUDIO IN - AUX
Connect to an analog audio output on the TV
or an analog device.
c VIDEO OUT
Connect to the composite video input on
the TV.
d HDMI OUT (ARC)
Connect to the HDMI input on the TV.
e LAN
Connect to the LAN input on a broadband
modem or router.
f DIGITAL IN - OPTICAL
Connect to an optical audio output on the
TV or a digital device.
g DIGITAL IN - COAXIAL
Connect to a coaxial audio output on the TV
or a digital device.
h ANTENNA FM
Signal input from an antenna. (Fixed FM
antenna for some models)
i SPEAKERS
Connect to the supplied speakers and
subwoofer.
FM
ANTENNA
5
English
EN
Remote control
This section includes an overview of the remote
control.
a ( Standby-On )
• Switch the home theater on or to standby.
• When EasyLink is enabled, press and hold
for at least three seconds to switch all
connected HDMI CEC compliant devices
to standby.
1
2
7
3
4
5
9
11
12
19
20
21
13
6
16
17
18
8
10
15
14
b ( Home )
Access the home menu.
c Source buttons
• DISC / POP-UP MENU : Switch to disc
source. Access or exit the disc menu
when you play a disc.
• RADIO : Switch to FM radio.
• AUDIO SOURCE : Select an audio input
source.
d BACK
• Return to a previous menu screen.
• In radio mode, press and hold to erase
the current preset radio stations.
e Navigation buttons
• Navigate menus.
• In radio mode, press left or right to start
auto search.
• In radio mode, press up or down to tune
the radio frequency.
f OK
Confi rm an entry or selection.
g / ( Previous/Next )
• Skip to the previous or next track,
chapter or fi le.
• In radio mode, select a preset radio station.
h ( Stop ) / ( Eject / Open/Close )
• Stop play.
• Press and hold for three seconds to open
or close the disc compartment, or eject
the disc.
i / ( Fast Backward / Fast Forward )
Search backwards or forward. Press
repeatedly to change the search speed.
j +/- ( Volume )
Increase or decrease volume.
k SOUND SETTINGS
Access or exit sound options.
l Alphanumeric buttons
Enter values or letters (using SMS style entry).
m REPEAT
Select or turn off repeat mode.
n TOP MENU
Access the main menu of a disc.
o OPTIONS
• Access more play options while playing a
disc or a USB storage device.
• In radio mode, set a radio station.
6 EN
p ( Play )
Start or resume play.
q ( Pause )
Pause play.
r ( Mute )
Mute or restore volume.
s AUDIO
Select an audio language or channel.
t SUBTITLE
Select subtitle language for video.
u Color buttons
Select tasks or options for Blu-ray discs.
3 Connect and set up
This section helps you connect your home theater
to a TV and other devices, and then set it up.
For information about the basic connections of
your home theater and accessories, see the quick
start guide. For a comprehensive interactive guide,
visit www.connectivityguide.philips.com.
Note
•
For identifi cation and supply ratings, see the type
plate at the back or bottom of the product.
• Before you make or change any connections,
make sure that all devices are disconnected from
the power outlet.
Connect speakers
The speaker cables are color-coded for easy
connection. To connect a speaker to your home
theater, match the color on the speaker cable to
the color on the connector.
Speaker position plays a critical role in setting up
a surround sound effect. For best effect, position
all the speakers towards the seating position and
place them close to your ear level (seated).
7
English
EN
Note
•
Surround sound depends on factors such as
room shape and size, type of wall and ceiling,
windows and refl ective surfaces, and speaker
acoustics. Experiment with the speaker positions
to fi nd the optimum setting for you.
Follow these general guidelines for speakers placement.
1 Seating position:
This is the center of your listening area.
2 FRONT CENTER (front center) speaker:
Place the center speaker directly in front of the
seating position, either above or below your TV.
3 FRONT LEFT (front left) and FRONT
RIGHT (front right) speakers:
Place the left and right speakers in the front, and
at equal distance from the center speaker. Make
sure that the left, right, and the center speakers
are at equal distance from your seating position.
4 REAR LEFT (rear left) and REAR RIGHT
(rear right) speakers:
Place the rear surround speakers to the left
and right side of your seating position, either
in line with it or slightly behind it.
5 SUBWOOFER (subwoofer):
Place the subwoofer at least one meter
to the left or right of the TV. Leave about
10-centimeter clearance from the wall.
Connect to TV
Connect your home theater to a TV to watch
videos. You can listen to the TV audio through your
home theater speakers.
Use the best quality connection available on your
home theater and TV.
Option 1: Connect to TV through HDMI
(ARC)
Best quality video
Your home theater supports HDMI version 1.4 -
Audio Return Channel (ARC). If your TV is HDMI
ARC compliant, you can hear the TV audio through
your home theater by using a single HDMI cable.
1 Using a High Speed HDMI cable, connect
the HDMI OUT (ARC) connector on your
home theater to the HDMI ARC connector
on the TV.
• The HDMI ARC connector on the TV
might be labeled differently. For details,
see the TV user manual.
2 On your TV, turn on HDMI-CEC operations.
For details, see the TV user manual.
• If you cannot hear the TV audio through
your home theater, set up the audio
manually (see 'Set up the audio' on page 10 ) .
Option 2: Connect to TV through
standard HDMI
Best quality video
If your TV is not HDMI ARC compliant, connect
your home theater to the TV through a standard
HDMI connection.
1 Using a High Speed HDMI cable, connect the
HDMI OUT (ARC) connector on your home
theater to the HDMI connector on the TV.
2 Connect an audio cable to hear the TV audio
through your home theater (see 'Connect
audio from TV and other devices' on page 8 ) .
3 On your TV, turn on HDMI-CEC operations.
For details, see the TV user manual.
• If you cannot hear the TV audio through
your home theater, set up the audio
manually (see 'Set up the audio' on page 10 ) .
Note
•
If your TV has a DVI connector, you can use an
HDMI/DVI adapter to connect to TV. However,
some of the features may not be available.
TV
8 EN
Option 3: Connect to the TV through
composite video
Basic quality video
If your TV does not have HDMI connectors, use
a composite video connection. A composite
connection does not support high-defi nition video.
1 Using a composite video cable, connect the
VIDEO connector on your home theater to
the VIDEO IN connector on the TV.
• The composite video connector might
be labeled AV IN , COMPOSITE , or
BASEBAND .
2 Connect an audio cable to hear the TV audio
through your home theater (see 'Connect
audio from TV and other devices' on page 8 ) .
3 When you watch TV programs, press
SOURCE on your home theater repeatedly
to select the correct audio input.
4 When you watch videos, switch your TV to
the correct video input. For details, see the
TV user manual.
Connect audio from TV and
other devices
Play audio from TV or other devices through your
home theater speakers.
Use the best quality connection available on your
TV, home theater, and other devices.
TV
TV
Note
•
When your home theater and TV are connected
through HDMI ARC, an audio connection is not
required (see 'Option 1: Connect to TV through
HDMI (ARC)' on page 7 ) .
Option 1: Connect audio through a digital
optical cable
Best quality audio
1 Using an optical cable, connect the OPTICAL
connector on your home theater to the
OPTICAL OUT connector on the TV or
other device.
• The digital optical connector might be
labeled SPDIF or SPDIF OUT .
Option 2: Connect audio through a digital
coaxial cable
Good quality audio
1 Using a coaxial cable, connect the COAXIAL
connector on your home theater to the
COAXIAL/DIGITAL OUT connector on the
TV or other device.
• The digital coaxial connector might be
labeled DIGITAL AUDIO OUT .
TV
9
English
EN
Option 3: Connect audio through analog
audio cables
Basic quality audio
1 Using an analog cable, connect the AUX
connectors on your home theater to the
AUDIO OUT connectors on the TV or other
device.
Set up speakers
Set up the speakers manually to experience
customized surround sound.
Before you start
Make the necessary connections described in the
quick start guide, and then switch the TV to the
correct source for your home theater.
1 Press ( Home ).
2 Select [Setup] , and then press OK .
3 Select [Audio] > [Speaker setup]
4 Enter the distance for each speaker, and
then listen to the test tones and change
the volume. Experiment with the speaker
positions to fi nd the ideal setting.
Set up EasyLink (HDMI-CEC
control)
This home theater supports Philips EasyLink,
which uses the HDMI-CEC (Consumer Electronics
Control) protocol. EasyLink-compliant devices that
are connected through HDMI can be controlled
by a single remote control.
VCR
Note
•
Depending on the manufacturer, HDMI-CEC is
known by many names. For information on your
device, see the user manual of the device.
• Philips does not guarantee 100% interoperability
with all HDMI-CEC devices.
Before you start
• Connect your home theater to the HDMI-
CEC compliant device through HDMI
connection.
• Make the necessary connections described in
the quick start guide, and then switch the TV
to the correct source for your home theater.
Enable EasyLink
1 Press ( Home ).
2 Select [Setup] , and then press OK .
3 Select [EasyLink] > [EasyLink] > [On] .
4 On your TV and other connected devices,
turn on HDMI-CEC control. For details, see
the user manual of the TV or other devices.
• On your TV, set the audio output to
'Amplifi er' (instead of TV speakers). For
details, see the TV user manual.
EasyLink controls
With EasyLink, you can control your home theater,
TV, and other connected HDMI-CEC compliant
devices with a single remote control.
• [One Touch Play] (One-touch play): When a
video disc is in the disc compartment, press
( Play ) to wake up the TV from standby, and
then play a disc.
• [One Touch Standby] (One-touch standby):
If one-touch standby is enabled, your home
theater can switch to standby with the
remote control of the TV or other HDMI-
CEC devices.
• [System Audio Control] (System audio
control): If system audio control is enabled,
the audio of the connected device is output
through your home theater speakers
automatically when you play the device.
• [Audio Input Mapping] (Audio input
mapping): If system audio control does not
work, map the connected device to the
correct audio input connector on your home
theater (see 'Set up the audio' on page 10 ) .
10 EN
Note
• To change the EasyLink control settings, press
( Home ), select [Setup] > [EasyLink] .
Set up the audio
If you cannot hear the audio output of a
connected device through your home theater
speakers, check that you have enabled Easylink on
all the devices (see 'Enable EasyLink' on page 9 ) .
Then, set up the EasyLink audio control.
1 Press ( Home ).
2 Select [Setup] , and then press OK .
3 Select [EasyLink] > [System Audio Control]
> [On] .
• To play the audio from the TV speakers,
select [Off] , and skip the following steps.
4 Select [EasyLink] > [Audio Input Mapping] .
5 Follow the onscreen instructions to map the
connected device to the audio inputs on your
home theater.
• If you connect your home theater to the
TV through an HDMI ARC connection,
make sure that the TV audio is mapped
to the ARC input on your home theater.
Connect and set up a home
network
Connect your home theater to a network router
through wired or wireless network connection,
and enjoy:
• Streamed multimedia content
• BD-Live applications
• Software update
Caution
•
Familiarize yourself with the network router,
media server software and networking
principles. If necessary, read documentation that
accompanies the network components. Philips is
not responsible for lost, damaged, or corrupt data.
Before you start
• For software updates, make sure that the
network router has access to the Internet
with high-speed connection and is not
restricted by fi rewalls or other security
systems.
• Make the necessary connections described in
the quick start guide, and then switch the TV
to the correct source for your home theater.
Set up the wired network
What you need
• A network cable (RJ45 straight cable).
• A network router (with DHCP enabled).
1 Using a network cable, connect the LAN
connector on your home theater to the
network router.
2 Press ( Home ).
3 Select [Setup] , and then press OK .
4 Select [Network] > [Network installation]
> [Wired (Ethernet)] .
5 Follow the onscreen instructions to complete
the setup.
• If connection fails, select [Retry] , and
then press OK .
6 Select [Finish] , and then press OK to exit.
• To view the network settings, select
[Setup] > [Network] > [View network
settings] .
LAN
www
11
English
EN
Set up the wireless network
Your home theater is Wi-Fi ready. Connect a Wi-Fi
dongle for easy access to a wireless network.
What you need
• A network router (with DHCP enabled). For
best wireless performance, coverage, and
compatibility, use 802.11n router;
• Connect a Wi-Fi dongle (Model: Philips
WUB1110, sold separately) to the
connector on your home theater.
1 Press ( Home ).
2 Select [Setup] , and then press OK .
3 Select [Network] > [Network installation]
> [Wireless (Wi-Fi)] , and then press OK .
4 Follow the onscreen instructions to select
and set up the wireless network.
• If connection fails, select [Retry] , and
then press OK .
5 Select [Finish] , and then press OK to exit.
• To view the network settings, select
[Setup] > [Network] > [View wireless
settings] .
4 Use your home theater
This section helps you use the home theater to
play media from a wide range of sources.
Before you start
• Make the necessary connections described in
the Quick start guide and the user manual.
• Switch the TV to the correct source for the
home theater.
Access the home menu
The home menu provides easy access to
connected devices, setup and other useful features
in your home theater.
1 Press ( Home ).
» The home menu is displayed.
2 Press the Navigation buttons and OK to
select the following:
• [play Disc] : Start disc play.
• [browse USB] : Access the USB content
browser
• [browse PC] : Access the computer
content browser.
• [Setup] : Access menus to change video,
audio and other settings.
3 Press ( Home ) to exit.
Discs
Your home theater can play DVDs, VCDs, CDs, and
Blu-ray discs. It can also play discs that you’ve made
at home, such as CD-R discs of photos and music.
1 Insert a disc into the home theater.
2 If the disc does not play automatically, press DISC
or select [play Disc] from the home menu.
3 Use the remote control to control play (see
'Remote control' on page 5 ) .
• It is normal to hear a little noise when
you play a Blu-ray disc. This does not
mean that your home theater is faulty.
Note
•
To avoid fl ickering, change the brightness of the
display .
12 EN
Play buttons
Button Action
Navigation
buttons
Navigate menus.
Up/Down: Rotate the picture
clockwise or counter-clockwise.
Left/Right: Flip the picture vertically
or horizontally.
OK Confi rm an entry or selection.
( Play )
Start or resume play.
Pause play.
Stop play.
/
Skip to the previous or next track,
chapter or fi le.
/
When a video is paused, search
backwards or forward.
AUDIO Select an audio language or channel.
SUBTITLE Select subtitle language for video.
DISC /
POP-UP
MENU
Access or exit the disc menu.
OPTIONS Access the advanced options when
you play your audio, video, or media
fi les (see 'Audio, video, and picture
options' on page 14 ) .
REPEAT Select or turn off repeat mode.
Synchronize picture and sound
If the audio and video are not synchronized, delay
the audio to match the video.
1 Press SOUND SETTINGS .
2 Select AUD SYNC , and then press OK .
3 Press the Navigation buttons (up/down) to
synchronize the audio with the video.
4 Press OK to confi rm.
Play Blu-ray 3D disc
Your home theater can play Blu-ray 3D video. Read
the 3D health warning before playing a 3D disc.
What you need
• A 3D TV.
• A pair of 3D glasses that are compatible with
your 3D TV.
• A 3D Blu-ray video
• A high speed HDMI cable (preferably version
1.4)
1 Using the high speed HDMI cable, connect
your home theater to a 3D compatible TV.
2 Make sure that the 3D video setting is
enabled. Press
( Home ), select [Setup] >
[Video] > [Watch 3D video] > [Auto] .
• To play 3D discs in 2D mode, select [Off] .
3 Play a Blu-ray 3D disc and put on the 3D glasses.
• During video search and in certain play
modes, the video is displayed in 2D. The
video display returns to 3D when you
resume play.
Bonus View on Blu-ray
On Blu-ray discs that support the Bonus View,
enjoy extra content such as commentaries in a
small screen window. Bonus View is also known as
picture-in-picture.
1 Enable Bonus View in the Blu-ray disc menu.
2 While you play the movie, press OPTIONS .
» The options menu is displayed.
3 Select [PIP selection] > [PIP] .
• Depending on the video, PIP menu [1] or
[2] is displayed.
• To disable Bonus View, select [Off] .
4 Select [2nd audio language] or [2nd Subtitle
Language] .
5 Select the language, and then press OK .
BD-Live on Blu-ray
Access additional features on the Blu-ray discs with
BD-Live content, such as internet chats with the
director, the latest movie trailers, games, wallpaper,
and ringtones.
BD-Live services and content vary from disc to disc.
What you need
• Blu-ray disc with BD-Live content
• a USB storage device, with at least 1 GB of
memory
1 Connect your home theater to a home
network with Internet access (see 'Connect
and set up a home network' on page 10 ) .
2 Connect a USB storage device to your home
theater.
3 Press ( Home ) and select [Setup] .
4 Select [Advanced] > [BD-Live security] >
[Off] to enable BD-Live.
• To disable BD-Live, select [On] .
13
English
EN
5 Select the BD-Live icon in the disc menu, and
then press OK .
» BD-Live starts to load. The loading time
depends on the disc and your internet
connection.
6 Press the Navigation buttons to navigate BD-
Live, and then press OK to select an option.
Note
•
To clear the memory on the storage device,
press
( Home ), select [Setup] > [Advanced]
> [Clear memory] .
Data fi les
Your home theater can play pictures, audio and
video fi les contained in a disc or a USB storage
device. Before you play a fi le, check that the fi le
format is supported by your home theater (see
'File formats' on page 20 ) .
1 Play the fi les from a disc or USB storage device.
2 To stop play, press .
• To resume the video from where you
stopped, press
( Play ).
• To play the video from the start, press .
Note
•
To play DivX DRM protected fi les, connect your
home theater to a TV through an HDMI cable.
Subtitles
If your video has subtitles in multiple languages,
select a subtitle language.
Note
•
Make sure that the subtitle fi le has the exact
same name as the video fi le. For example, if the
video fi le is named 'movie.avi', name the subtitle
fi le as 'movie.srt' or 'movie.sub'.
• Your home theater supports the following fi le
formats: .srt, .sub, .txt, .ssa, .ass, smi, and .sami. If
the subtitles do not appear correctly, change the
character set.
1 While playing video, press SUBTITLE to
select a language.
2 For DivX or RMVB/RM videos, if the subtitles
do not appear correctly, continue the
following steps to change the character set.
3 Press OPTIONS .
» The options menu is displayed.
4 Select [Character set] , and then select a
character set that supports the subtitle.
Asia Pacifi c and China
Character
Set
Language
[Standard] Albanian, Danish, Dutch, English,
Finnish, French, Gaelic, German,
Italian, Kurdish (Latin), Norwegian,
Portuguese, Spanish, Swedish, Turkish
[Chinese] Simplifi ed Chinese
[Chinese-
Traditional]
Traditional Chinese
[Korean] English and Korean
VOD code for DivX
Before you purchase DivX videos and play them
on your home theater, register the home theater
on www.divx.com using the DivX VOD code.
1 Press ( Home ).
2 Select [Setup] , and then press OK .
3 Select [Advanced] > [DivX® VOD Code] .
» The DivX VOD registration code for
your home theater is displayed.
USB storage devices
Enjoy pictures, audio, and video stored on a USB
storage device such as an MP4 player or digital camera.
What you need
• A USB storage device that is formatted for
FAT or NTFS fi le systems, and complies with
the Mass Storage Class.
• A media fi le in one of the supported fi le
formats (see 'File formats' on page 20 ) .
Note
•
If you use a USB extension cable, USB HUB, or
USB multi-reader, the USB storage device may
not be recognized.
14 EN
1 Connect a USB storage device to the
( USB ) connector on your home theater.
2 Press ( Home ).
3 Select [browse USB] , and then press OK .
» A content browser is displayed.
4 Select a fi le, and then press OK .
5 Press the play buttons to control play (see
'Play buttons' on page 12 ) .
Audio, video, and picture options
Use advanced features when you play pictures, audio
and video fi les from a disc or a USB storage device.
Audio options
While playing audio, repeat an audio track, a disc,
or a folder.
1 Press OPTIONS repeatedly to cycle through
the following functions:
• RPT TRK / RPT FILE : Repeat the current
track or fi le.
• RPT DISC / RPT FOLD : Repeat all the
tracks on the disc or the folder.
• RPT RDOM : Play audio tracks in random
order.
• RPT OFF : Turn off the repeat mode.
Video options
While watching video, select options such as
subtitles, audio language, time search, and picture
settings. Depending on the video source, some
options are not available.
1 Press OPTIONS .
» The video options menu is displayed.
2 Press the Navigation buttons and OK to
select and change:
• [Audio language] : Select audio language
for video.
• [Subtitle Language] : Select subtitle
language for video.
• [Subtitle shift] : Change the subtitle
position on the screen.
• [Info] : Display information about what is
playing.
• [Character set] : Select a character set
that supports the DivX subtitle.
• [Time search] : Skip to a specifi c part of the
video by entering the time of the scene.
• [2nd audio language] : Select the second
audio language for Blu-ray video.
• [2nd Subtitle Language] : Select the second
subtitle language for Blu-ray video.
• [Titles] : Select a specifi c title.
• [Chapters] : Select a specifi c chapter.
• [Karaoke] : Change the karaoke settings.
• [Angle list] : Select a different camera angle.
• [Menus] : Display the disc menu.
• [PIP selection] : Display Picture-in-Picture
window when playing a Blu-ray disc that
supports the Bonus View.
• [Zoom] : Zoom into a video scene or
picture. Press the Navigation buttons
(left/right) to select a zoom factor.
• [Repeat] : Repeat a chapter or title.
• [Repeat A-B] : Mark two points within a
chapter or track to repeat play, or turn
off the repeat mode.
• [Picture settings] : Select a predefi ned
color setting.
Picture options
While viewing a picture, zoom into the picture,
rotate it, add animation to a slideshow, and change
the picture settings.
1 Press OPTIONS .
» The picture options menu appears.
2 Press the Navigation buttons and OK to
select and change the following settings:
• [Rotate +90] : Rotate the picture 90
degree clockwise.
• [Rotate -90] : Rotate the picture 90
degree counter-clockwise.
• [Zoom] : Zoom into a video scene or
picture. Press the Navigation buttons
(left/right) to select a zoom factor.
• [Info] : Display picture information.
• [Duration per slide] : Select the display
speed for each picture in a slide show.
• [Slide animation] : Select animation for
the slide show.
• [Picture settings] : Select a predefi ned
color setting.
• [Repeat] : Repeat a selected folder.
Musical slideshow
If the picture and audio fi les are from the same
disc or USB storage device, you can create a
musical slideshow.
1 Select an audio track, and then press OK .
15
English
EN
2 Press BACK , and go to the picture folder.
3 Select a picture, and then press ( Play ) to
start the slideshow.
4 Press to stop slideshow.
5 Press again to stop music.
Note
•
Make sure that the picture and audio formats
are supported by your home theater (see 'File
formats' on page 20 ) .
Radio
Listen to FM radio on your home theater, and
store up to 40 radio stations.
Note
•
AM and digital radio are not supported.
• If no stereo signal is detected, or if fewer than
fi ve stations are found, you are prompted to
install the radio stations again.
1 Connect the FM antenna to the ANTENNA FM
on your home theater (if not already connected).
• For the best reception, place the antenna
away from the TV or other sources of
radiation.
2 Press RADIO .
» If you have already installed the radio stations,
the last channel that you listened to is played.
» If you have not installed any radio
stations, the message AUTO
INSTALL...PRESS PLAY appears on
the display panel. Press
( Play ).
3 Use the remote control to listen or to
change radio stations.
Button Action
/
or
Alphanumeric
buttons
Select a preset radio station.
Navigation
buttons
Left/Right: Search for a radio
station.
Up/Down: Fine tune a radio
frequency.
Press to stop the installation of
radio stations.
BACK
Press and hold to erase the
preset radio station.
OPTIONS Manual:
1) Press
OPTIONS . 2)
Press
/ to select your
preset. 3) Press
OPTIONS
again to store the radio station.
Automatic: Press and hold for
three seconds to reinstall the
radio stations.
SUBTITLE Toggle between the stereo and
mono sounds.
Tuning grid
In some countries, you can toggle the FM tuning
grid between 50 kHz and 100 kHz. Switching the
tuning grid erases all preset radio stations.
1 Press RADIO .
2 Press .
3 Press and hold ( Play ) to toggle between 50
kHz or 100 kHz.
MP3 player
Connect a MP3 player to play audio fi les.
What you need
• An MP3 player.
• A 3.5mm stereo audio cable.
1 Using the 3.5mm stereo audio cable, connect
the MP3 player to the MUSIC iLINK
connector on your home theater.
2 Press AUDIO SOURCE repeatedly until
MUSIC I-LINK appears on the display panel.
3 Press the buttons on the MP3 player to select
and play audio fi les.
16 EN
Browse PC through DLNA
Access and play the pictures, audio and video fi les
from a computer or media server on the home
network through your home theater.
Before you start
• Install a DLNA-compliant media server
application on your device. Make sure that
you download an application that works best
for you. For example,
• Windows Media Player 11 or higher for PC
• Twonky Media Server for Mac or PC
• Enable media sharing of fi les. For details,
check the user manual of the media server
software software.
1 Connect your home theater to a home
network . For better video quality, use wired
connection whenever possible.
2 Connect the computer and other DLNA-
compatible devices to the same home
network.
3 Press ( Home ).
4 Select [browse PC] , and then press OK .
» A content browser is displayed.
5 Select a device on the network.
» The folders in the selected device are
displayed. Depending on the media
server, the folder names may vary.
• If you cannot see the folders, make sure
that you enable media sharing on the
selected device so that the content is
available for sharing.
6 Select a fi le, and then press OK .
• Some media fi les may not play due
to compatibility issues. Check the fi le
formats supported by your home theater.
7 Press the play buttons to control play (see
'Play buttons' on page 12 ) .
Karaoke
Available only in selected model and region
Play a Karaoke disc on your home theater and sing
along with the music.
What you need
• A Karaoke microphone.
• Karaoke discs.
Caution
•
To prevent loud feedback or unexpected noise,
turn the microphone volume to the minimum
before you connect the microphone to your
home theater.
1 Connect a karaoke microphone to the MIC
connector on your home theater.
2 Switch your TV to the correct source for
your home theater.
3 Make sure that audio post processing is
enabled on your home theater (see 'Speaker
settings' on page 19 ) .
4 While playing a karaoke disc, press OPTIONS .
» The options menu is displayed.
5 Select [Karaoke] , and then press OK .
» The karaoke setup menu is displayed.
6 Press the Navigation buttons (up/down) and
OK to change the following settings:
• [Microphone] : Turn the microphone on
or off.
• [Microphone volume] : Change the
microphone volume.
• [Echo] : Change the echo level.
• [Key] : Change the pitch to match your voice.
Choose sound
This section helps you choose the ideal sound for
your video or music.
1 Press SOUND SETTINGS .
2 Press the Navigation buttons (left/ right) to
access the sound options on the display.
Sound settings Description
SOUND Select a sound mode.
SURROUND Select surround sound or stereo
sound.
TREBLE Change the high frequency
output.
MID Change the middle frequency
output.
BASS Change the low frequency output.
AUD SYNC Delay the audio to match the
video.
3 Select an option, and then press OK .
17
English
EN
4 Press BACK to exit.
If you do not press a button within a minute,
the menu exits automatically.
Sound mode
Select predefi ned sound modes to suit your video
or music.
1 Press SOUND SETTINGS .
2 Select SOUND , and then press OK .
3 Press the Navigation buttons (up/down) to
select a setting on the display:
• MOVIE : Enjoy a cinematic audio
experience, specially enhanced for
movies.
• MUSIC : Recreate the original recording
environment of your music, in the studio
or at a concert.
• ORIGINAL : Experience the original
sound of your movies and music, without
added sound effects.
• NEWS : Hear every word with optimized
speech and clear vocals.
• GAMING : Enjoy thrilling arcade sounds,
ideal for action-packed video games or
loud parties.
4 Press OK to confi rm.
Surround sound mode
Experience an immersive audio experience with
surround sound modes.
1 Press SOUND SETTINGS .
2 Select SURROUND , and then press OK .
3 Press the Navigation buttons (up/down) to
select a setting on the display:
• AUTO : Surround sound based on the
audio stream.
• MULTI-CH : Immersive multi-channel
sound for an enhanced movie
experience.
• STEREO : Two-channel stereo sound. Ideal
for listening to music.
4 Press OK to confi rm.
5 Change settings
The home theater settings are already confi gured
for optimal performance. Unless you have a reason
to change a setting, we recommend that you keep
the default setting.
Note
•
You cannot change a setting that is grayed out.
• To return to the previous menu, press
BACK . To exit the menu, press
( Home ).
Language settings
1 Press ( Home ).
2 Select [Setup] , and then press OK .
3 Select [Preference] , and then press OK .
4 Press the Navigation buttons and OK to
select and change:
• [Menu language] : Select a display
language for menu.
• [Audio] : Select an audio language for discs.
• [Subtitle] : Select a subtitle language for discs.
• [Disc menu] : Select a menu language for
discs.
Note
•
If your preferred disc language is not available,
select [Others] from the list, and enter the 4-digit
language code found at the end of this user manual .
• If you select a language that is not available on a
disc, the home theater uses the default language
of the disc.
18 EN
Picture and video settings
1 Press ( Home ).
2 Select [Setup] , and then press OK .
3 Select [Video] , and then press OK .
4 Press the Navigation buttons and OK to
select and change:
• [TV display] : Select a picture format to fi t
the TV screen.
• [HDMI video] : Select the resolution of
video signal that is output from HDMI OUT
(ARC) on your home theater. To enjoy the
selected resolution, make sure that your TV
supports the selected resolution.
• [HDMI Deep Color] : Recreate the natural
world on your TV screen by displaying
vivid images using billion colors. Your home
theater must be connected to a Deep
Color enabled TV through an HDMI cable.
• [Picture settings] : Select pre defi ned
color settings for the video display.
• [Watch 3D video] : Set HDMI video to
support 3D or 2D video.
Note
•
If you change a setting, make sure that the TV
supports the new setting.
Audio settings
1 Press ( Home ).
2 Select [Setup] , and then press OK .
3 Select [Audio] , and then press OK .
4 Press the Navigation buttons and OK to
select and change:
• [Night mode] : For quiet listening, decrease
the volume of loud sounds on your home
theater. Night mode is only available for
Dolby-encoded DVD and Blu-ray discs.
• [HDMI Audio] : Set the HDMI audio
output from your TV, or disable HDMI
audio output from the TV.
Parental control settings
1 Press ( Home ).
2 Select [Setup] , and then press OK .
3 Select [Preference] , and then press OK .
4 Press the Navigation buttons and OK to
select and change:
• [Change Password] : Set or change your
password for parental control access.
If you do not have a password or have
forgotten your password, enter 0000 .
• [Parental control] : Restrict access to discs
that are recorded with age ratings. To play
all discs, irrespective of the ratings, select
8 or [Off] .
Display settings
1 Press ( Home ).
2 Select [Setup] , and then press OK .
3 Select [Preference] , and then press OK .
4 Press the Navigation buttons and OK to
select and change:
• [Auto subtitle shift] : Enable or disable
automatic repositioning of subtitles on
TVs that support this feature.
• [Display panel] : Set the brightness of the
home theater front panel display.
• [VCD PBC] : Enable or disable the content
menu navigation of VCD and SVCD discs
with Play Back Control feature.
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
他の言語で
- English: Philips HTS3582/98 User manual