Dell PowerEdge C6145 クイックスタートガイド

Dell PowerEdge

C6145

Getting Started

With Your System

系统使用入门

Mengaktifkan Sistem Anda

はじめに

시스템시작 안내서

Dell PowerEdge

C6145

Getting Started

With Your System

Notes, Cautions, and Warnings

NOTE:

A NOTE indicates important information that helps you make better use of

your computer

CAUTION: A CAUTION indicates potential damage to hardware or loss of

data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission

of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of

Dell Inc. AMD

®

is a registered trademark and AMD Opteron™ is a trademark of

Advanced Micro Devices, Inc. Red Hat Enterprise Linux

®

and Enterprise Linux

®

are

registered trademarks of Red Hat, Inc. in the United States and/or other countries.

Novell

®

is a registered trademark and SUSE™ is a trademark of Novell Inc. in the United

States and other countries. Citrix

®

and XenServer

®

are either registered trademarks or

trademarks of Citrix Systems, Inc. in the United States and/or other countries. VMware

®

is a registered trademarks or trademarks of VMWare, Inc. in the United States or other

countries.

Other trademarks and trade names may be used in this publication to refer to either the

entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

Regulatory Model B05S

January 2011 P/N HR6G0 Rev. A00

Getting Started With Your System | 5

CAUTION: Restricted Access Location

This server is intended for installation only in restricted access locations as

defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions apply:



Access can only be gained by service persons or by users

who have been

instructed about the reasons for the restrictions applied to the location and

about any precautions that shall be taken.



Access is through the use of a tool or lock and key, or other means of

security, and is controlled by the authority responsible for the location.

Installation and Configuration

WARNING: Before performing the following procedure, review and follow the

safety instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Installing the Tool-Less Rail Solution

WARNING: Whenever you need to lift the system, get others to assist you.

To avoid injury, do not attempt to lift the system by yourself.

WARNING: The system is not fixed to the rack or mounted on the rails. To

avoid personal injury or damage to the system, you must adequately

support the system during installation and removal.

WARNING: To avoid a potential electrical shock hazard, a third wire safety

grounding conductor is necessary for the rack installation. The rack

equipment must provide sufficient airflow to the system to maintain proper

cooling.

CAUTION: When installing rails in a square-hole rack it is important to

ensure that the square peg slides through the square holes.

Getting Started With Your System | 6

1

Pull on the latch release buttons on the end piece midpoints to open

the rail latches.

2

Align the end pieces of the rails on the vertical rack flanges to seat

the pegs in the bottom hole of the first U and the top hole of the

second U. Engage the back end of the rails until the latches lock in

place.

NOTE:

The rails can be used in both square-hole (item 1 in the following figure)

and round-hole racks (item 2 in the following figure).

3

Repeat Step 1 and Step 2 to position and seat the front end pieces on

the vertical flanges.

NOTE:

To remove the rails, pull on the latch release button on the end piece

midpoint and unseat each rail.

4

On each vertical rack flange on the rear, put two screw bases into the

two square holes right above the rail.

5

Install the chassis stabilizer shipping brackets (optional) on the rear

rack flanges and simultaneously fasten the screws.

NOTE:

To transport systems already installed in the rack, ensure that the two

chassis stabilizer shipping brackets (optional) are in place.

Getting Started With Your System | 7

6

Slide the system into the rack.

7

Tighten the thumbscrews to secure the ears of the system to the front

of the rack flanges.

Getting Started With Your System | 8

Optional-Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to

plug into each connector. Be sure to tighten the screws (if any) on the monitor’s

cable connector.

Getting Started With Your System | 9

Connecting the Power Cable(s)

Connect the system’s power cable(s) to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor. Plug the other end of the

power cables into a grounded electrical outlet or a separate power source such as

an uninterrupted power supply or a power distribution unit.

Getting Started With Your System | 10

Turning on the System

Press the power button(s) either on the front or back of the system and on the

monitor. The power indicators should light.

Getting Started With Your System | 11

Complete the Operating System Setup

To install an operating system for the first time, see the installation and

configuration documentation for your operating system. Be sure the operating

system is installed before installing hardware or software not purchased with the

system.

Supported Operating Systems



Microsoft Windows HPC Server 2008 R2 (64-bit)



Microsoft Windows Server 2008 Core R2 (64-bit)



Microsoft Windows Server 2008 R2 Hyper-V



Microsoft Windows Server 2008 R2 Enterprise (64-bit)



Red Hat Enterprise Linux 5.5 (64-bit)



Red Hat Enterprise Linux 6.0 (Certification only)



SUSE Linux Enterprise Server 11 SP1 (64-bit)



VMware ESX Server 4.1 U1 and ESXi Embedded



Citrix XenServer 5.6 Feature Pack 1

NOTE:

For the latest information on supported operating systems, see

support.dell.com

.

Getting Started With Your System | 12

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as a

separate document.

The

Hardware Owner’s Manual

provides information about system features and

describes how to troubleshoot the system and install or replace system

components. This document is available at

support.dell.com/manuals

.

Dell systems management application documentation provides information

about installing and using the systems management software. This document is

available online at

support.dell.com/manuals

.

NOTE:

Always check for updates on

support.dell.com/manuals

and read the

updates first because they often supersede information in other documents.

Información de la NOM (sólo para México)

La información que se proporciona a continuación aparece en el dispositivo

descrito en este documento, en cumplimiento de los requisitos de la Norma

Oficial Mexicana (NOM):

Importador Dell Inc. de México, S.A. de C.V.

Paseo de la Reforma 2620-11° Piso

Col. Lomas Atlas

11950 México, D.F.

Número de modelo B05S

Voltaje de alimentación 100-240 V CA con alimentación de 1 100 W

200-240 V CA con alimentación de 1 400 W

Frecuencia 50/60 Hz

Consumo eléctrico De 12 a 6,7 A con alimentación de 1 100 W

8,6 A con alimentación de 1 400 W

Getting Started With Your System | 13

Technical Specifications

Processor (Per System Board)

Processor type Four AMD Opteron 6100 Series

processors

Expansion Bus (Per System Board)

Bus type PCI Express Generation 2

Expansion slots

PCIe One x16, low profile

Two x16, half-length/half-height

Daughter card PCIe One x16, Mezzanine slot

Memory (Per System Board)

Architecture 32 x DDR3 1066/1333 MHz RDIMM

or UDIMM

Memory module sockets 32 x DDR3 DIMM sockets

Memory module capacities 2 GB, 4 GB, 8 GB, or 16 GB

Minimum RAM 64 GB

Maximum RAM 512 GB

Drives

Hard drives Up to twelve 3.5-inch, hot-swappable

SAS/SATA drives or up to twenty four

2.5-inch, hot-swappable

SAS/SATA/SSD drives

NOTE:

SAS hard drives are supported by add-on

card.

Connectors (Per System Board)

Back

NIC Two RJ-45 (10/100/1000 Mbps

Ethernet)

Serial 9-pin, DTE, 16550-compatible

USB Two 4-pin, USB 2.0-compliant

Getting Started With Your System | 14

Video 15-pin D-Sub VGA

Management port Dedicated Ethernet port for remote

management access

V

ideo (Per System Board)

Video type On-board AST2050 video controller

Video memory 8 MB

Power

AC power supply (per power supply)

Wattage 1023 W low line/1100 W high line

Voltage 100-240 V CA, 50-60 Hz, maximum

input current: 12.0 Amps

Heat dissipation 4217.063 BTU/hr maximum

Wattage

1400 W

Voltage 200-240 V CA, 50-60 Hz, maximum

input current: 8.6 Amps

Heat dissipation 5724 BTU/hr maximum

Maximum inrush current Initial In-rush Current cannot exceed 55

Amps (peak). Secondary In-rush

Current cannot exceed 35 Amps (peak).

Battery (per system board)

System battery

CR 2032 3.0-V lithium ion coin cell

RAID battery (optional) 3.7-V lithium ion battery pack

Physical

Height 8.76 cm (3.45 in)

Width 44.8 cm (17.6 in)

Depth 79.0 cm (31.1 in)

Weight (maximum

configuration)

42 kg (92.61 lb)

Weight (empty) 16.5 kg (36.38 lb)

Getting Started With Your System | 15

Environmental

NOTE:

For additional information about environmental measurements for specific system

configurations, see

www.dell.com/environmental_datasheets

.

Temperature

Operating 10° to 35°C (50° to 95°F) with a

maximum temperature gradation of

10°C per hour

NOTE:

For altitudes above 2950 feet, the maximum

operating temperature is derated 1°F/550 ft.

Storage –40° to 65°C (–40° to 149°F) with a

maximum temperature gradation of

20°C per hour

Relative humidity

Operating 20% to 80% (noncondensing) with a

maximum humidity gradation of 10%

per hour

Storage 5% to 95% (noncondensing)

Maximum vibration

Operating 0.26 Grms at 5–350 Hz

Storage 1.88 Grms at 10–500 Hz for 15 min

Maximum shock

Operating One shock pulse in the positive z axis

(one pulse on each side of the system)

of 31 G for 2.6 ms in the operational

orientation

Storage Six consecutively executed shock

pulses in the positive and negative x, y,

and z axes (one pulse on each side of

the system) of 71 G for up to 2 ms;

Six consecutively executed shock

pulses in the positive and negative x, y,

and z axes (one pulse on each side of

the system) of 22 G faired square wave

pulse with velocity change at 200

inches/second (508 centimeters/second)

Getting Started With Your System | 16

Environmental

Altitude

Operating –16 to 3,048 m (–50 to 10,000 ft)

NOTE:

For altitudes above 2950 feet, the maximum

operating temperature is derated 1°F/550 ft.

Storage –16 to 10,600 m (–50 to 35,000 ft)

Airborne contaminant level

Class G2 or lower as defined by

ISA-S71.04-1985

Dell PowerEdge

C6145

系统使用入门

注、小心和警告

注：

"注"表示可以帮助您更好地使用计算机的重要信息。

小心："小心"表示如果不遵循说明，就有可能损坏硬件或导致数据丢失。

警告："警告"表示可能会导致财产损失、人身伤害甚至死亡。

______________

本出版物中的信息如有更改，恕不另行通知。

未经

Dell Inc.

书面许可，严禁以任何形式复制这些材料。

本文中使用的商标：

Dell™

、

DELL

徽标和

PowerEdge™

是

Dell Inc.

的商

标。

AMD

®

和

AMD Opteron™

是

Advanced Micro Devices, Inc.

的注册商标

和商标。

Red Hat Enterprise Linux

®

和

Enterprise Linux

®

是

Red Hat, Inc.

在美

国和/或其它国家/地区的注册商标。

Novell

®

和

SUSE™

是

Novell Inc.

在美

国和其它国家/地区的注册商标和商标。

Citrix

®

和

XenServer

®

是

Citrix

Systems, Inc.

在美国和/或其它国家/地区的注册商标或商标。

VMware

®

是

VMWare, Inc.

在美国或其它国家/地区的注册商标或商标。

本出版物中述及的其它商标和商品名称是指拥有相应商标和商品名称的公司

或其产品。

Dell Inc.

对本公司的商标和产品名称之外的其它商标和产品名称

不拥有任何专有权。

管制型号 B05S

2011 年 1 月 P/N HR6G0 Rev. A00

系统使用入门 | 19

小心：受限访问位置

此服务器仅适用于安装在

IEC 60950-1:2001

的

Cl. 1.2.7.3

中定义的受限访

问位置，并遵循以下两个条件

:



仅维修人员或对该位置施加限制的理由以及应当采取的防备措施已

完全领会的用户，方可对此服务器进行访问。



访问是通过使用工具或锁和钥匙，或其它安全手段来实现，并且由

负责该位置的管理机构来控制。

安装和配置

警告：执行下列步骤之前，请阅读并遵循系统随附的安全说明。

打开系统包装

打开系统包装并识别每项物品。

安装免工具拆装导轨解决方案

警告：需要提起系统时，请让别人帮您。为避免受伤，请勿尝试独自提起系

统。

警告：系统未固定到机架上或未安装在导轨上。为避免人身伤害或损坏系统，

必须在安装和拆卸过程中对系统进行充分支撑。

警告：为避免可能的电击伤害，机架安装需要第三根导线安全接地连接器。机

架设备必须为系统提供足够的气流以保持适当冷却。

小心：在方孔机架中安装导轨时，请确保方形连接销滑过方孔。

系统使用入门 | 20

1

拔起尾段正中央的闩锁释放按钮以打开导轨闩锁。

2

对齐垂直机架边缘上的导轨尾段，将连接销按入第一个

U

底部

的孔和第二个

U

顶部的孔中。接合导轨后端直到闩锁锁定到位。

注：

导轨可同时用于方孔（下图中的项目

1

）和圆孔机架

（下图中的项目

2

）。

3

重复步骤

1

和步骤

2

定位前端段并将其固定在垂直边缘。

注：

要卸下导轨，请拔起尾段正中央的闩锁释放按钮并取出每个导轨。

4

在背面的每个垂直机架边缘，将两个螺钉座放入导轨正上方的

两个方孔。

5

在背面机架边缘安装运输时稳固机箱的支架（可选）并同时拧

紧螺钉。

注：

要运输已经安装在机架上的系统，请确保两个运输时稳固机箱的支架

到位（可选）。

正面视图

后视图

ページを読み込んでいます...

Dell PowerEdge C6145 クイックスタートガイド

関連論文