Dell PowerEdge C6105 クイックスタートガイド

Dell PowerEdge

C6105

Getting Started

With Your System

系统使用入门

Mengaktifkan Sistem Anda

はじめに

시스템 시작하기

Dell PowerEdge

C6105

Getting Started

With Your System

Notes, Cautions, and Warnings

NOTE:

A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of

data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

______________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission

of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of

Dell Inc. AMD® is a registered trademark and AMD Opteron™ is a trademark of

Advanced Micro Devices, Inc. Red Hat Enterprise Linux® and Enterprise Linux® are

registered trademarks of Red Hat, Inc. in the United States and/or other countries.

Novell® is a registered trademark and SUSE™ is a trademark of Novell Inc. in the United

States and other countries. Citrix® and XenServer® are either registered trademarks or

trademarks of Citrix Systems, Inc. in the United States and/or other countries. VMware®

is a registered trademarks or trademarks of VMWare, Inc. in the United States or other

countries.

Other trademarks and trade names may be used in this publication to refer to either the

entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

Regulatory Model B03S

November 2013 P/N 4JG39 Rev. A05

Getting Started With Your System | 3

CAUTION: Restricted Access Location

This server is intended for installation only in restricted access locations as

defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions apply:

•

Access can only be gained by service persons or by users

who have been

instructed about the reasons for the restrictions applied to the location and

about any precautions that shall be taken.

•

Access is through the use of a tool or lock and key, or other means of

security, and is controlled by the authority responsible for the location.

Installation and Configuration

WARNING: Before performing the following procedure, review and follow the

safety instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Installing the Tool-Less Rail Solution

WARNING: Whenever you need to lift the system, get others to assist you.

To avoid injury, do not attempt to lift the system by yourself.

WARNING: The system is not fixed to the rack or mounted on the rails.

To avoid personal injury or damage to the system, you must adequately

support the system during installation and removal.

WARNING: To avoid a potential electrical shock hazard, a third wire safety

grounding conductor is necessary for the rack installation. The rack

equipment must provide sufficient airflow to the system to maintain proper

cooling.

CAUTION: When installing rails in a square-hole rack it is important to

ensure that the square peg slides through the square holes.

Getting Started With Your System | 4

1

Align the end pieces of the rails on the vertical rack flanges to seat

the pegs in the bottom hole of the first U and the top hole of the

second U. Engage the back end of the rails until the latches lock in

place.

NOTE:

The rails can be used in both square-hole (item 1 in the following figure)

and round-hole racks (item 2 in the following figure).

Figure 1. Pushing the Latch Release Buttons

2

Repeat Step 1 to position and seat the front end pieces on the vertical

flanges.

NOTE:

To remove the rails, pull on the latch release button on the end piece

midpoint and unseat each rail.

3

Slide the system into the rack.

4

If present, remove the chassis stabilizer shipping bracket (optional)

from the rack.

NOTE:

To transport systems already installed in the rack, ensure that the two

chassis stabilizer shipping brackets (optional) are in place.

Getting Started With Your System | 5

Figure 2. Installing the Chassis Stabilizer Shipping Brackets

5

Tighten the thumbscrews to secure the ears of the system to the front

of the rack flanges.

Figure 3. Installing the Chassis onto the Rack.

Getting Started With Your System | 6

Optional-Connecting the Keyboard, Mouse, and Monitor

Figure 4. Optional—Connecting the Keyboard, Mouse and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to

plug into each connector. Be sure to tighten the screws (if any) on the monitor’s

cable connector.

Getting Started With Your System | 7

Connecting the Power Cable(s)

Figure 5. Connecting the Power Cable

Connect the system’s power cable(s) to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor. Plug the other end of the

power cables into a grounded electrical outlet or a separate power source such as

an uninterrupted power supply or a power distribution unit.

Getting Started With Your System | 8

Turning on the System

Figure 6. Pressing the Power Button on the Front of the System and the Monitor

Figure 7. Pressing the Power Button on the Back of the System

Press the power button(s) either on the front or back of the system and on the

monitor. The power indicators should light.

Getting Started With Your System | 9

Complete the Operating System Setup

To install an operating system for the first time, see the installation and

configuration documentation for your operating system. Be sure the operating

system is installed before installing hardware or software not purchased with the

system.

NOTE:

For the latest information on supported operating systems, see

dell.com/ossupport

.

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as a

separate document.

The Hardware Owner’s Manual provides information about system features and

describes how to troubleshoot the system and install or replace system

components. This document is available at

dell.com/support/manuals

.

Dell systems management application documentation provides information

about installing and using the systems management software. This document is

available online at

dell.com/support/manuals

.

NOTE:

Always check for updates on

dell.com/support/manuals

and read the

updates first because they often supersede information in other documents.

Getting Started With Your System | 10

NOM Information (Mexico Only)

The following information is provided on the device described in this document

in compliance with the requirements of the official Mexican standards (NOM):

Importer Dell Inc. de México, S.A. de C.V.

Paseo de la Reforma 2620-11° Piso

Col. Lomas Atlas

11950 México, D.F.

Model number

B03S

Supply voltage 100-240 V AC with 470 W/750

W/1100 W Power

200-240 V AC with 1400 W Power

Frequency

50/60 Hz

Current consumption 6.5-3.5 Amps with 470 W Power

8.6 Amps with 1400 W Power

9.5-5.0 Amps with 750 W Power

12-6.7 Amps with 1100 W Power

Getting Started With Your System | 11

Technical Specifications

Processor (Per System Board)

Processor type One or two AMD C32 Series processors

One or two AMD Opteron 4000 Series

processors

One or two AMD Opteron 4200 Series

processors

One or two AMD Opteron 4300 Series

processors

Expansion Bus (Per System Board)

Bus type

PCI Express Generation 2

Expansion slots

PCIe

One x16, half-length, half-height

Daughter card PCIe

One x8, custom slot

Memory (Per System Board)

Architecture 12 x DDR3 800/1066/1333/1600* MHz

registered memory modules with /ECC

Memory module sockets

12 x DDR3 DIMM sockets

Memory module capacities

2 GB, 4 GB, 8 GB, or 16 GB

Minimum RAM

12 GB

Maximum RAM

192 GB

NOTE:

System memory working frequency is up to 1333MT/s only.

Drives

Hard drives Up to twelve 3.5-inch, hot-swappable SAS/

SATA drives or up to twenty four 2.5-inch,

hot-swappable SAS/SATA/SSD drives

NOTE:

SAS hard drives are supported by add-on card.

Getting Started With Your System | 12

Connectors (Per System Board)

Back

NIC

Two RJ-45 (10/100/1000 Mbps Ethernet)

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin D-Sub VGA

Management port Dedicated Ethernet port for remote

management access

Video (Per System Board)

Video type On-board AST2050 video controller or

AST1100

Video memory

8 MB

Power

AC power supply (per power supply)

Wattage

470 W

Voltage 100-240 VAC, 50-60 Hz, input current

range: 6.5-3.5 Amps

Heat dissipation

2390 BTU/hr maximum

Wattage

750 W

Voltage 100-240 VAC, 50-60 Hz, input current

range: 9.5-5.0 Amps

Heat dissipation

3414 BTU/hr maximum

Wattage

1023 W low line/1100W high line

Voltage 100-240 VAC, 50-60 Hz, input current

range: 12.0-6.7 Amps

Heat dissipation

4575 BTU/hr maximum

Wattage

1400 W

Voltage 200-240 VAC, 50-60 Hz, maximum input

current: 9.6 Amps

Heat dissipation

5432 BTU/hr maximum

Getting Started With Your System | 13

Maximum inrush current Initial In-rush Current cannot exceed

55 Amps (peak). Secondary In-rush

Current cannot exceed 35 Amps (peak).

Battery (per system board)

System battery

CR 2032 3.0-V lithium ion coin cell

RAID battery (optional)

3.7-V lithium ion battery pack

Physical

Height

8.76 cm (3.45 in)

Width

44.8 cm (17.6 in)

Depth

75.1 cm (29.47 in)

Weight (maximum

configuration)

33.67 kg (74.2 lb)

Weight (empty)

15.11 kg (33.32 lb)

Environmental

NOTE:

For additional information about environmental measurements for specific system

configurations, see

www.dell.com/environmental_datasheets

.

Temperature

Operating 10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C per hour

NOTE:

For altitudes above 2950 feet, the maximum

operating temperature is derated 1°F/550 ft.

Storage –40° to 65°C (–40° to 149°F) with a

maximum temperature gradation of 20°C per

hour

Relative humidity

Operating 20% to 80% (noncondensing) with a

maximum humidity gradation of 10% per

hour

Storage

5% to 90% (noncondensing)

Maximum vibration

Operating

0.26 Grms at 5–350 Hz

Storage

1.93 Grms at 10–500 Hz for 15 min

Getting Started With Your System | 14

Maximum shock

Operating One shock pulse in the positive z axis

(one pulse on each side of the system) of

31 G for 2.6 ms in the operational orientation

Storage Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of

71 G for up to 2 ms;

Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of

27 G faired square wave pulse with velocity

change at 235 inches/second

(597 centimeters/second)

Altitude

Operating –16 to 3,048 m (–50 to 10,000 ft)

NOTE:

For altitudes above 2950 feet, the maximum

operating temperature is derated 1°F/550 ft.

Storage

–16 to 10,600 m (–50 to 35,000 ft)

Airborne contaminant level

Class

G2 or lower as defined by ISA-S71.04-1985

Dell PowerEdge

C6105

系统使用入门

注、小心和警告

注：“注”表示可以帮助您更好地使用计算机的重要信息。

小心：“小心”表示如果不遵循说明，就有可能损坏硬件或导致数据丢失。

警告：“警告”表示可能会导致财产损失、人身伤害甚至死亡。

______________

本文档中的信息如有更改，恕不另行通知。

未经 Dell Inc. 书面许可，严禁以任何形式复制这些材料。

本文中使用的商标：Dell™、DELL 徽标和 PowerEdge™ 是 Dell Inc. 的商标。

AMD® 和 AMD Opteron™ 分别是 Advanced Micro Devices, Inc. 的注册商标和商标。

Red Hat Enterprise Linux® 和 Enterprise Linux® 是 Red Hat, Inc. 在美国和/或其他国

家/地区的注册商标。Novell® 和 SUSE™ 分别是 Novell Inc. 在美国和其他国家/地区

的注册商标和商标。Citrix® 和 XenServer® 是 Citrix Systems, Inc. 在美国和/或其他

国家/地区的注册商标或商标。VMware® 是 VMware, Inc. 在美国或其他国家/地区的

注册商标。

本出版物中可能使用其他商标和产品名称来指拥有相应商标和产品名称的公司或其

产品。Dell Inc. 对不属于自己的商标和商品名称不拥有任何专有权。

管制型号 B03S

2013 年 11 月 P/N 4JG39 Rev. A05

系统使用入门 | 17

小心：受限访问位置

此服务器仅用于安装在由 IEC 60950-1: 2001 的 Cl. 1.2.7.3 定义的满足下列两个条

件的受限访问位置中：

• 仅维修人员或对该位置施加限制的理由以及应当采取的防备措施已完全领

会的用户，方可对此服务器进行访问。

• 访问是通过使用工具或锁和钥匙，或其它安全手段来实现，并且由负责该

位置的管理机构来控制。

安装和配置

警告：执行下列步骤之前，请先阅读并遵循系统随附的安全说明。

打开系统包装

打开系统包装并识别每项物品。

安装免工具拆装滑轨解决方案

警告：需要提起系统时，请让其他人进行协助。为避免受伤，请勿尝试独

自提起系统。

警告：系统并未固定到机架上，也并没有安装在滑轨上。为避免人身伤害

或系统损坏，在安装和拆卸时，必须给系统提供足够的支撑。

警告：为避免可能的电击伤害，安装机架时需要第三根导线安全接地线。

机架设备必须为系统提供足够的通风以维持适当的冷却效果。

小心：在方孔机架中安装滑轨时，务必确保方形插销穿过方孔。

系统使用入门 | 18

1 在机架垂直凸缘上对齐滑轨的尾段，将插销分别插入第一个 U 型螺栓

的底孔中和第二个 U 型螺栓的顶孔中。使滑轨后端卡入，直到闩锁锁

定到位。

注：

滑轨在方孔机架（下图中的项目 1）和圆孔机架（下图中的项目 2）

中均可使用。

图 1. 按压闩锁释放按钮

2 重复步骤 1，在垂直凸缘上定位和插入前尾段。

注：

要卸下滑轨，请拔起尾段正中央的闩锁释放按钮并取出每根滑

轨。

3 将系统滑入到机架中。

4 如果存在用于运输时稳固机箱的支架（可选），请将其从机架上卸下。

注：要运输已经安装在机架上的系统，请确保安装两个运输时稳固机

箱的支架（可选）。

ページが読み込まれています...

Dell PowerEdge C6105 クイックスタートガイド

Dell PowerEdge C6105 クイックスタートガイド

他の言語で

関連論文