Instruction Manual
Underwater Case
PT-023
For the digital camera
CAMEDIA C-8080 Wide Zoom
■ Thank you for buying the Underwater Case PT-023.
■ Please read this instruction manual carefully and use the product safely
and correctly.
■ Please keep this instruction manual for reference after reading it.
■ Wrong use may cause damage to the camera on the inside from water
leakage, and repair may not be possible.
■ Before use, perform an advance check as described in this manual.
PPO-05
JP
This section describes how to mount this product on the PT-023. Before mounting, make sure no foreign matter is attached to the
O-rings or the O-ring contact surfaces.
Port clamping buckle
Silicone O-ring (POL-105A)
Lens window clamping buckle
Silicone O-ring (POL-105B)
Silicone O-ring (POL-105C)
Lens window clamping boss
Lens window
Silicon grease for O-rings
Pick for removing O-ring
Lens cap
PT-023 mount cap
To ensure continued safe and reliable performance, always perform the maintenance after every diving session.
Refer to “Ensuring the case stays waterproof” and other maintenance instructions in the PT-023 case’s instruction manual. Apply the
same procedures to this product.
Make sure that the PT-023 case and PPO-05 are completely dry before removing the PPO-05 from the PT-023. To remove the PPO-
05, reverse the mounting procedure.
This product allows the WCON-08D wide conversion lens to be used in underwater
shooting. However, due to the refraction index of water, the image angle in underwater
shooting is less than in normal daylight shooting.
Applicable waterproof case
Applicable conversion lenses and WCON-08D
Shooting image angle Underwater Approx. 62 degrees
Withstanding pressure Water pressure equivalent up to a depth
of 40 meters
Main materials Polycarbonate, brass, stainless steel,
FL reinforced glass, silicone and rubber (NBR).
Dimensions Max. diameter 156 mm depth 90 mm
Weight 705 g (without conversion lens)
This product uses the following consumable items.
Silicone O-rings
Silicone grease for O-rings
Please pay very close attention to this information. Failure to observe warnings when
using this product may pose a serious risk of injury and even death.
WARNING
Note : We reserve the right to change the external appearance and specifications without notice.
Failure to observe this information when using the product could lead to injury or
material damage.
CAUTION
Turn the PPO-05’s lens
window clamping buckles
(x2) in the direction of the
arrow (counterclockwise)
until they stop (about 120
degrees).
Remove the cosmetic ring
(provided with the C-8080
Wide Zoom) from the PT-
023.
Note: Turn the cosmetic ring
counterclockwise to
remove.
Insert the CLA-8
conversion lens adapter
inside the PPO-05 and
attach it carefully to the
end of the C-8080 Wide
Zoom’s lens.
Remove the lens window
clamping bosses of the
PPO-05 from the grooves
on the lens window
clamping buckles. Remove
the lens window when it
separates from the PPO-05
body.
Attach the WCON-08D
wide conversion lens to the
mount on the CLA-8.
Removing the PPO-05 Wide Port
Shooting environment Image angle
Underwater Approx. 62°
Product model Description
PPO-105A O-ring for use in PT-023 mount of PPO-05
PPO-105B O-ring for use on lens window of PPO-05
PPO-105C O-ring for use on lens window mount section of PPO-05
Product model Description
PSOLG-1 Lubricant or common use with PT-023
Note : Images shot underwater using this product may be distorted at the peripheries.
Thank you for purchasing an Olympus lithium-polymer battery. Before use, please read this instruction manual to ensure your safety and
keep it handy for future reference.
This product is the wide port used for combining the C-8080 Wide Zoom's Waterproof case (PT-023), the C-8080 Wide Zoom's Conversion
Lens Adapter (CLA-8) and Wide Conversion Lens (WCON-08D) with C-8080 Wide Zoom Digital Camera.
Using this product in combination with the CLA-8 conversion lens adapter andWCON-08D wide conversion lens enables wide-angle
underwater shooting of approx. 62-degree underwater image angle.
The WCON-08D has an image angle of Approx. 23 mm (when converted into 35 mm film) on land, but the underwater image angle is
reduced due to the refraction index of water.
Images shot underwater may be distorted at the peripheries.
When this product is used in combination with the PT-023 waterproof case, the camera's built-in flash cannot be used.
Disclaimer
Unauthorized copying of this manual in whole or in part, except for private use, is prohibited. Unauthorized reproduction is strictly prohibited.
OLYMPUS CORPORATION shall not be responsible for any damages, loss of profit or any claims by third parties in case of any damage
occurring from incorrect use of this product.
IMPORTANT - Please read the following before using the product
This case has been designed for use underwater at depths up to 40 meters.
This product must be used in combination with the PT-023 waterproof case. Do not use this product on its own.
To ensure correct and safe use of this product, please refer to the PT-023 waterproof case's instruction manual. Be sure to observe all
handling precautions and follow the instructions carefully, particularly with regard to system check, as well as care, maintenance and
storage.
For safe use
This instruction manual uses pictographs to show correct use of the product and to warn of any danger to the user and other persons as well
as damage to property. These pictographs and their meanings are shown below.
WARNING
This product should be kept out of the reach of infants and children to avoid accidents such as the following:
Injury caused by dropping the product onto the body from a height.
Injury caused by swallowing small parts. Please consult a doctor immediately if this happens.
This product is partially made of glass. If it is broken or smashed, glass splinters could cause injury. Please handle this product carefully.
If water gets inside this product during underwater use, stop using it immediately, remove any liquid or moisture from the product, and
take out the camera and lens.
Do not disassembly or modify this product. This may result in injury.
Silicone lubricant is not edible.
CAUTION
Do not leave this product anywhere where it may be exposed to high temperatures. This could result in deterioration of its components.
When mounting this product on the PT-023 waterproof case, follow the instructions in this manual.
Before taking this product off the PT-023 waterproof case, make sure that the case is completely dry.
Do not mount, take off, open or close this product in locations where it may be exposed to sand, dust or dirt. This can affect the integrity
of the waterproof seal and lead to water penetration.
This product has been designed and manufactured for use at water pressures equivalent to depths of up to 40 meters. Please note that
diving at depths greater than 40 meters may result in deformation or damage to this product, as well as to the camera and lens. In this
case, water penetration may occur.
When sealing this product, take care to ensure no foreign matter such as sand, dirt and hair are caught by the O-rings and contact
surfaces.
Before storing this product, always remove the camera and lens from it.
Do not apply excessive force to the buckle used in attaching and detaching this product.
When attaching or detaching the PPO-05 from the PT-023, do not use force to turn the clamping buckle if it is hard to rotate. Using too
much force may damage the buckle-clamping bosses on the PT-023 case.
PPO-05
After aligning the lens
window with the notch on
the PPO-05’s mount, align
the grooves of the lens
window clamping buckles
with the corresponding port
clamping bosses on the
PPO-05.
Before shooting, be sure to
perform the first check and
final system check as
indicated for the PT-023.
For details, refer to the PT-
023's instruction manual.
Turn the left and right
clamping buckles all the
way in the direction of the
arrows (by about 120
degrees) until they click.
Make sure that the buckles
do not turn easily any
more.
EN
Instruction Manual
Maintenance
Image Angle in Underwater Shooting
Specifications
Consumable Items
Mounting on the PT-023 waterproof case
Names of Parts
After shooting, remove the inserted camera
and lens, seal the empty PT-023 again and
immerse it in tap water as soon as possible to
remove any salt attached to it.
After making sure that the PT-023 his
completely dry, remove this product from the
PT-023.
Remove the O-rings from this product using
the provided pick. Be careful not to damage
the rings.
Remove sand and dust from the O-rings.
Check for foreign matter, scratches and
cracks by squeezing the O-ring gently with
your fingers and rubbing them gently over the
entire circumference to feel for abnormalities.
If any foreign matter is attached to the O-ring
grooves, wipe it off with a clean, lint-free cloth
or cotton swab. Also remove any foreign
matter from the O-ring contact surfaces of
this product.
After removing foreign matter, apply the
provided lubricant to the O-rings and fit the
rings into the O-ring grooves.To apply
lubricant, squeeze a small drop onto your
finger and spread it thinly and evenly over
the entire circumference of the O-ring.
Align the notch on the
PPO-05’s PT-023 mount
with the protrusion on the
PT-023’s mount. Gently
attach the PPO-05 to the
PT-023.
Align the two port locking
buckle grooves on the PPO-05
with the port locking bosses on
the PT-023. To ensure that they
are secure, turn the locking
buckles on both sides in the
direction of the arrow until they
click and stop (approx. 120
°
).
Note:
Turn the buckles on both
sides simultaneously.
When the PPO-05 is
used, the provided
diffusion plate cannot
be used.
http://www.olympus.com/
Shinjuku Monolith, 3-1 Nishi Shinjuku 2-chome, Shinjuku-ku,
Tokyo, Japan
Suite D-10-P1, Level 10, Plaza Mont' Kiara, 2 Jalan 1/70C,
Mont' Kiara, 50480 Kuala Lumpur, Malaysia
Tel: (603)6203 3882 Fax: (603) 6203 3885
31 Gilby Road, Mt. Waverley, VIC, 3166
1300 659 678 (Customer Service Line)
9F Hyundai Marines Bldg., 646 Yeoksam-Dong, Kangnam-Gu,
Seoul 135-080, Korea
URL: http://www.olympus.co.kr
Tel: 080-777-3200, 3201
OLYMPUS STUDIO
1 North Bridge Road #01-05/34/35 High Street Centre,
Singapore 179094
URL: http://www.olympus.com.sg
Tel:65-6339-7686 Fax: 65-6339-3934
Enquiry Hotline: 1800-OLYMPUS(1800-659-6787)
ページを読み込んでいます...
/
