Turn the left and right
clamping buckles all the
way in the direction of the
arrows (by about 120
degrees) until they click.
Make sure that the buckles
do not turn easily any
more.
Note : Turn the left and
right buckles
simultaneously.
PPO-01
JP
This section describes how to mount this product on the PT-020. Before mounting, make sure no foreign matter is attached to the
O-rings or the O-ring contact surfaces.
Port clamping buckle
Silicone O-ring (POL-101A)
Silicon grease for O-rings
Pick for removing O-ring
Lens cap
PT-020 mount cap
Align the grooves on the
PPO-01’s two port
clamping buckles with the
corresponding port
clamping bosses on the PT-
020 case.
PPO-01
EN
Instruction Manual
Applicable waterproof case PT-020
Applicable camera C-5060 Wide Zoom
Withstanding pressure Water pressure equivalent up to a depth of
40 meters
Main materials Polycarbonate, brass, stainless steel,
FL reinforced glass, silicone, rubber (NBR) and
aluminum.
Dimensions Max. diameter 82 mm depth 42.4 mm
Weight Approx. 170 grams (without conversion lens)
Note : We reserve the right to change the external appearance and specifications without notice.
Specifications
Consumable Items
Names of Parts
This product uses the following consumable items.
Silicone O-rings
Silicone grease for O-rings
Mounting on the PT-020 waterproof case
Product model Description Recommended retail price in Japan
PPO-101 O-ring for use in PT-020 mount of PPO-01 1,000 yen
Thank you for purchasing an Olympus lithium-polymer battery. Before use, please read this instruction manual to ensure your safety and
keep it handy for future reference.
The PPO-01 is the standard port used when combining the PT-020 Waterproof case with the C-5060 Wide Zoom. (This is the same standard
port as the one pre-mounted on the case body provided with the PT-020.)
This product is designed for use when the PT-020 is combined with the C-5060 Wide Zoom (only).
Please pay very close attention to this information. Failure to observe warnings when
using this product may pose a serious risk of injury and even death.
WARNING
Failure to observe this information when using the product could lead to injury or
material damage.
CAUTION
Disclaimer
Unauthorized copying of this manual in whole or in part, except for private use, is prohibited. Unauthorized reproduction is strictly prohibited.
OLYMPUS CORPORATION shall not be responsible for any damages, loss of profit or any claims by third parties in case of any damage
occurring from incorrect use of this product.
IMPORTANT - Please read the following before using the product
This case has been designed for use underwater at depth s up to 40 meters.
This product must be used in combination with the PT-020 waterproof case. Do not use this product on its own.
To ensure correct and safe use of this product, please refer to the PT-020 waterproof case's instruction manual. Be sure to observe all
handling precautions and follow the instructions carefully, particularly with regard to system check, as well as care, maintenance and
storage.
For safe use
This instruction manual uses pictographs to show correct use of the product and to warn of any danger to the user and other persons as well
as damage to property. These pictographs and their meanings are shown below.
WARNING
This product should be kept out of the reach of infants and children to avoid accidents such as the following:
Injury caused by dropping the product onto the body from a height.
Injury caused by swallowing small parts. Please consult a doctor immediately if this happens.
This product is partially made of glass. If it is broken or smashed, glass splinters could cause injury. Please handle this product carefully.
If water gets inside this product during underwater use, stop using it immediately, remove any liquid or moisture from the product, and
take out the camera and lens.
Do not disassembly or modify this product. This may result in injury.
Silicone lubricant is not edible.
CAUTION
Do not leave this product anywhere where it may be exposed to high temperatures. This could result in deterioration of its components.
When mounting this product on the PT-020 waterproof case, follow the instructions in this manual.
Before taking this product off the PT-020 waterproof case, make sure that the case is completely dry.
Do not mount, take off, open or close this product in locations where it may be exposed to sand, dust or dirt. This can affect the integrity
of the waterproof seal and lead to water penetration.
This product has been designed and manufactured for use at water pressures equivalent to depths of up to 40 meters. Please note that
diving at depths greater than 40 meters may result in deformation or damage to this product, as well as to the camera and lens. In this
case, water penetration may occur.
When sealing this product, take care to ensure no foreign matter such as sand, dirt and hair are caught by the O-rings and contact
surfaces.
Before storing this product, always remove the camera and lens from it.
Do not apply excessive force to the buckle used in attaching and detaching this product.
To ensure continued safe and reliable performance, always perform the maintenance after every diving session.
Refer to “Ensuring the case stays waterproof” and other maintenance instructions in the PT-020 case’s instruction manual. Apply the
same procedures to this product.
Make sure that the PT-020 case and PPO-02 are completely dry before removing the PPO-02 from the PT-020. To remove the PPO-
02, reverse the mounting procedure.
Removing the PPO-01 Standard Port
Maintenance
After shooting, remove the inserted camera
and lens, seal the empty PT-020 again and
immerse it in tap water as soon as possible to
remove any salt attached to it.
After making sure that the PT-020 his
completely dry, remove this product from the
PT-020.
Remove the O-rings from this product using
the provided pick. Be careful not to damage
the rings.
Remove sand and dust from the O-rings.
Check for foreign matter, scratches and
cracks by squeezing the O-ring gently with
your fingers and rubbing them gently over the
entire circumference to feel for abnormalities.
If any foreign matter is attached to the O-ring
grooves, wipe it off with a clean, lint-free cloth
or cotton swab. Also remove any foreign
matter from the O-ring contact surfaces of
this product.
After removing foreign matter, apply the
provided lubricant to the O-rings and fit the
rings into the O-ring grooves.To apply
lubricant, squeeze a small drop onto your
finger and spread it thinly and evenly over
the entire circumference of the O-ring.
Product model Description Recommended retail price in Japan
PSOLG-1 Lubricant or common use with PT-020 800 yen
Before shooting, be sure to
perform the first check and
final system check as
indicated for the PT-020.
For details, refer to the PT-
020's instruction manual.
http://www.olympus.com/
Shinjuku Monolith, 3-1 Nishi Shinjuku 2-chome, Shinjuku-ku,
Tokyo, Japan
Suite D-10-P1, Level 10, Plaza Mont' Kiara, 2 Jalan 1/70C,
Mont' Kiara, 50480 Kuala Lumpur, Malaysia
Tel: (603)6203 3882 Fax: (603) 6203 3885
31 Gilby Road, Mt. Waverley, VIC, 3166
1300 659 678 (Customer Service Line)
9F Hyundai Marines Bldg., 646 Yeoksam-Dong, Kangnam-Gu,
Seoul 135-080, Korea
URL: http://www.olympus.co.kr
Tel: 080-777-3200, 3201
OLYMPUS STUDIO
1 North Bridge Road #01-05/34/35 High Street Centre,
Singapore 179094
URL: http://www.olympus.com.sg
Tel:65-6339-7686 Fax: 65-6339-3934
Enquiry Hotline: 1800-OLYMPUS(1800-659-6787)
ページが読み込まれています...
-
1
-
2
他の言語で
- English: Olympus PPO-01 User manual
関連論文
-
Olympus PPO-05 ユーザーマニュアル
-
-
-
-
-
-
-
-
-