Plasma Display
Installation
Instructions
TH-50PHD3V
TH-50PH30V
TH-50PHD5V
TH-42PWD4V
TH-42PWD5V
Before attempting to install this model,
please read these instructions completely.
Operation method of plasma display, please see the
Operation Manual for the TH-50PHD3,
TH-50PHD30,TH-50PHD5, TH-42PWD4,
TH-42PWD5.
TQZH330-1
Model No.
Model No.
2
Thank you very much for purchasing the Plasma Display.
Installation work should only be carried out by a qualified technician.
• If the unit is installed incorrectly, the display may fall down and personal injury may result.
Precautions with regard to setting up
WARNING
Always have a service technician perform the installation.
• The internal components of the display may be hot and cause burns. If the product is not
correctly installed and adjusted, damage may result to the product.
Make sure that all safety factors regarding strength of installation are observed.
• If the installation strength is insufficient, the display may fall down and personal injury may
result.
Do not install in places which are unable to bear loads.
• If the strength of the installation surface is insufficient, the display may fall down and personal
injury may result.
Caution
Do not install in places which are subject to humidity, dust, oil fumes, water vapor or
excessive heat.
• These can have adverse effects on Plasma Display operation, and fire or electric shocks may
result.
Two people are required to install and remove the display.
• If two people are not present, the display may be dropped, and personal injury may result.
Maintain a space of at least 10 cm (3
15
/
16
inch) at the top, bottom and sides of the display,
and at least 1.9 cm (
3
/
4
inch) at the rear of the display.
• The display has air outlet holes at the top and air intake holes at the bottom and rear. These
holes must not be covered, otherwise fire may result.
3
Components
Points to note during installation
This model is for the Plasma Display. Do not use this model for any other purpose.
In order to ensure correct, problem-free operation of the Plasma Display, do not
install the Display in any of the following places.
• Places which are next to sprinklers or sensors
• Places which are subject to vibration or shocks
• Places which are close to high-voltage wires or electric motors
• Places in direct contact with air from heaters
When installing the wall-hanging bracket unit, use a mounting method appropriate
to the type of wall.
This model does not include the bolts needed to mount the bracket to the wall.
Please purchase screws suitable for the material (wood, steel frame, concrete,
etc.) of the wall on which the bracket and Plasma Display are to be mounted.
Insert the power cord plug for the Plasma Display into a wall outlet which is close
and easily accessible.
Provide adequate ventilation so that the temperature around the display does not
rise above 40 . If there is insufficient movement of air inside the display, heat
may build up inside the display, and fire may result.
This Plasma Display is for use only with the following optional accessories.
Use with any other type of optional accessories may cause instability which could
result in the possibility of injury.
(All of following accessories are manufactured by Matsushita Electric Industrial
Co., Ltd.)
• Wall-hanging bracket (vertical) --- TY-WK42PV1
• Wall-hanging bracket (for PDP with PC) --- TY-WK42PRE1 (for U.S.A only)
Always be sure to ask a qualified technician to carry out set-up.
Make sure that you have the following accessory.
There is following accessory in addition to the accessories indicated by the TH-
50PHD3, TH-50PHD30, TH-50PHD5, TH-42PWD4, TH-42PWD5 operating
instructions.
Fixing screw
( M5-35)........................2
The wall-hanging bracket weights
approx. 6 kg (13.2 lbs.), a 50-inch
display weights approx. 45 kg (99.2 lbs.),
a 42-inch display weights approx. 30 kg
(66 lbs.). Using the bracket dimensions
shown in the diagram at right, confirm
that the 6 locations for mounting the
bracket to the wall are able to bear the
combined weight. If the wall is not strong
enough, reinforce it.
4
Installation procedure
•
The wall-hanging bracket has 24 installation holes.
If the wall material is not strong enough to install
the display using six installation holes, use some of
the spare holes. However, depending on the wall
material, cracks may develop and attachment
intensity becomes inadequate if the screws are
inserted too close to each other.
Note
Note
1. Check the strength of the installation location.
2. Install the wall-hanging bracket to the wall.
• Hang the bracket so that the arrow on the bracket points to the right.
• If it is necessary to embed bolts or nuts beforehand because the wall is made of concrete, use
the bracket itself to determine the correct installation hole positions, or use the dimension
diagram to calculate the hole positions. Then embed the M6 bolts or nuts into the holes. Embed
the bolts so that they protrude from the wall by 10 mm (
13
/32 inch) to 15 mm (
19
/32 inch).
Units
: mm
( ): inch
930 (36
5
/8)
490 (19
19
/64)
450 (17
23
/32)
50
(1
31
/32)
30
(1
3
/16)
20
(
25
/32)
20
(
25
/32)
450 (17
23
/32)450 (17
23
/32)
100
(3
15
/16)50
(1
31
/32)
15
(
19
/32)
Wall installation holes
(6 locations)
Used for routing wires
behind a wall
15
(
19
/32)
Dimensions of the wall-hanging bracket
(sold separately)
Fixing screw
Fixing screw
Installation procedure
1.
Insert a bolt into the upper right hole.
2.
Use a level to adjust the bracket so that it is parallel to the
ground. Insert bolts into the other 5 holes.
3.
Insert and slightly tighten the fixing screw (M5 x 35). Do not
insert the bolt more than 5 mm (
13
/
64
inch). The display
cannot be installed in the correct position if the bolt is over-
tightened.
*
Note: In this case, the wall-hanging bracket fixing screw
(M5 x 135) is not used.
•
Use commercially available bolts which suit the wall materials for installation to the wall.
Note
Note
5. Tighten the mounting bolts.
• Be sure to fix the left side fixing screws to
stabilize the display.
3. Attach the insulation spacers to the display.
Remove the four bolts from the display.
In the holes that previously held the 4
M8 bolts, insert the insulating spacer,
toothed pan washer, and pan head
bolt with hex socket (4 each) that came
with the wall-hanging bracket.
Remove M8 bolts
Fixing
Pan head bolt with hex socket
Toothed pan washer
Insulating spacer
4. Install the display to the wall-hanging bracket.
Position the display so that the power switch is located at the bottom.
Insulating spacer
Power
switch
Top holes
Lower
holes
• Do not lift the display too high, otherwise it
may become unhooked.
Push the upper insulating spacers
on the display into the notches at
the top of the wall-hanging bracket
until they are hooked in, then lower
the display into place.
While lifting the display slightly,
insert the lower insulating spacers
on the display into the lower
hanging holes in the wall-hanging
bracket, then lower the display.
Tighten the fixing screws on the left
side.
Bolt locations
(upper and lower)
(Left side view)
Note
Note
5
Matsushita Electric Industrial Co., Ltd
Web Site: http://www.panasonic.co.jp/global/
450 (17
33
/64)
20
(
25
/32)
B
900 (35
7
/16)
A
C
490 (19
19
/64)
D
930 (36
39
/64)
G
19 (
3
/4)
F
E
Upright Installation example
Units : mm
( ) : inch
For 50 Inch For 42 Inch
Dimensions
A
B
C
D
E
F
G
1210 (47
41
/64)
724 (28
1
/2)
136.5 (5
3
/8)
97.5 (3
27
/32)
128.5 (5
1
/16)
151.5 (5
31
/32)
98 (3
55
/64)
1210 (47
41
/64)
724 (28
1
/2)
136.5 (5
3
/8)
97.5 (3
27
/32)
128.5 (5
1
/16)
151.5 (5
31
/32)
98 (3
55
/64)
1020 (40
5
/32)
610 (24
1
/64)
79.5 (3
1
/8)
40.5 (1
19
/32)
33.5 (1
5
/16)
56.5 (2
7
/32)
89 (3
1
/2)
Units : mm ( ) : inch
Printed in Japan
M0601-1052
(Recycled paper)
TH-50PHD3V
TH-50PHD5V
TH-42PWD4V
TH-42PWD5V
2
3
4
5
C Matsushita Electric Industrial Co., Ltd. 2002
/