ENGLISH
Introduction
Congratulations on your purchase and
welcome to Philips! To fully benet from
the support that Philips offers, register your
product at www.philips.com/welcome.
General description (Fig. 1)
1 Protection cap
2 Shaving heads
3 Shaving unit
4 Hair chamber
5 On/off button
6 Charging light
7 Socket for micro USB plug
8 Wheel of retaining frame
9 Retaining frame
10 Cutter
11 Guard
12 Release button
13 Cleaning brush
14 Adapter
15 Micro USB plug
16 Storage pouch (PQ288 only)
17 Philips Cleaning Spray (HQ110)
(Optional)
Important
Read this user manual carefully before you
use the appliance and save it for future
reference.
Danger
- Warning: Keep the appliance and the
adapter dry.
- This symbol means: Forbidden to clean
under a running tap (Fig. 2).
Warning
- The adapter contains a transformer.
Do not cut off the adapter to replace
it with another plug, as this causes a
hazardous situation.
- Warning: Do not use this appliance
close to a bathtub, shower or other
containers lled with water.
- This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
- Children should be supervised to
ensure that they do not play with the
appliance.
Caution
- Do not use the shaver or the adapter if
it is damaged.
- Only use the adapter supplied to
charge the appliance.
- If the adapter is damaged, always have
it replaced with one of the original type
in order to avoid a hazard.
- Charge, use and store the shaver at a
temperature between 5°C and 35°C.
- Do not use the shaver in combination
with pre-shave lotions, creams, foams,
gels or other cosmetic products.
General
- The adapter transforms 100-240 volts
to a safe low voltage of less than 24 volts.
Compliance with standards
- This Philips appliance complies with all
standards regarding electromagnetic elds
(EMF). If handled properly and according
to the instructions in this user manual, the
appliance is safe to use based on scientic
evidence available today.
- This shaver complies with the
applicable IEC safety standards.
Charging
Make sure the shaver is switched off when
you start to charge it.
When you charge the shaver for the rst
time or after a long period of non-use, let it
charge continuously for 12 hours. Charging
normally takes approx. 8 hours.
Charge the appliance when the motor
stops or starts running slower.
For optimal performance, only charge the
shaver when the battery is low.
Do not leave the appliance connected to
the mains for more than 24 hours.
1 Put the micro USB plug in the
shaver (Fig. 3).
2 Put the adapter in the wall socket.
, The charging light goes on to indicate
that the appliance is charging (Fig. 4).
Note: Charge the shaver for at least 8 hours
but not more than 24 hours.
PQ227, PQ226, PQ225, PQ222
Register your product and get support at
www.philips.com/welcome
4222.002.5315.2
1
2
3 4
5
6 7
8 9
10
14
15 16
17
18 19
20 21
22
23
24 25
11
12 13
3 Remove the adapter from the wall
socket and pull the micro USB plug
out of the shaver when the battery is
fully charged (Fig. 5).
Note: The shaver does not run from the mains.
When the battery is empty, you have to recharge
the battery before you can use the shaver again.
Cordless shaving time
A fully charged shaver has a cordless shaving
time of approximately 30 minutes.
Using the appliance
Note: The shaver cannot be used directly from
the mains.
1 Remove the protection cap.
2 Press the on/off button to switch on
the shaver (Fig. 6).
3 Move the shaving heads over your
skin. Make both straight and circular
movements (Fig. 7).
Note: Shave on a dry face only. Do not use the
shaver in combination with gel, foam or water.
Note: Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
4 Press the on/off button to switch off
the shaver.
5 Clean the shaver after every shave
(see chapter ‘Cleaning and maintenance’).
6 Put the protection cap on the shaver
to prevent damage and to avoid
dirt accumulation in the shaving
heads (Fig. 8).
Note: Make sure that the lug of the protection
cap covers the release button.
Cleaning and maintenance
Never use scouring pads, abrasive cleaning
agents or aggressive liquids such as petrol
or acetone to clean the appliance.
Clean the shaver after every shave to
guarantee better shaving performance. For
the best cleaning result, we advise you to
use Philips Cleaning Spray (HQ110). Ask
your Philips dealer for information.
Note: Philips Shaving Head Cleaning Spray
(HQ110) may not be available in all countries.
Contact the Consumer Care Centre in your
country about the availability of this accessory.
After every shave: shaving unit
and hair chamber
1 Switch off the shaver, remove the
adapter from the wall socket and pull
the micro USB plug out of the shaver.
2 Clean the top of the appliance with
the cleaning brush supplied (Fig. 9).
3 Press the release button (1) and pull
the shaving unit in a straight upward
movement off the shaver (2). (Fig. 10)
4 Clean the inside of the shaving unit
with the cleaning brush (Fig. 11).
5 Clean the hair chamber with the
cleaning brush (Fig. 12).
6 Put the shaving unit back onto the
shaver (Fig. 13).
Every two months: shaving heads
Note: Do not use cleaning agents or alcohol
to clean the shaving heads. Only use Philips
Cleaning Spray (HQ110).
1 Switch off the shaver, remove the
adapter from the wall socket and pull
the small plug out of the shaver.
2 Press the release button (1) and pull
the shaving unit in a straight upward
movement off the shaver (2) (Fig. 10).
3 Turn the orange wheel anticlockwise
(1) and remove the retaining frame
(2) (Fig. 14).
4 Remove and clean one shaving head
at a time. Each shaving head consists
of a cutter and a guard (Fig. 15).
Note: Do not clean more than one cutter and
guard at a time, since they are all matching
sets. If you accidentally mix up the cutters
and guards, it may take several weeks before
optimal shaving performance is restored.
5 Remove the guard from the
cutter (Fig. 16).
6 Clean the cutter with the short-
bristled side of the cleaning brush.
Brush carefully in the direction of the
arrows (Fig. 17).
7 Clean the guard with the long-bristled
side of the cleaning brush (Fig. 18).
8 Put the cutter back into the guard
after cleaning (Fig. 19).
9 Put the shaving heads back into the
shaving unit (Fig. 20).
10 Put the retaining frame back into the
shaving unit (1) and turn the orange
wheel clockwise (2) (Fig. 21).
11 Put the shaving unit back onto the
shaver (Fig. 13).
Storage
Keep the appliance dry.
Use and store the appliance at a
temperature between 5°C and 35°C.
1 Switch off the shaver.
2 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 8).
Note: Make sure that the lug of the protection
cap covers the release button.
Replacement
Replace the shaving heads every two years
for optimal shaving results.
Replace damaged or worn shaving heads
with Philips shaving heads only (HQ4+ for
China or HQ56 for the rest of the world).
For instructions on how to remove the
shaving heads, see chapter ‘Cleaning and
maintenance’, section ‘Every two months:
shaving heads’.
Ordering accessories
To purchase accessories for this
appliance, please visit our online shop at
www.shop.philips.com/service. If the
online shop is not available in your country,
go to your Philips dealer or a Philips service
centre. If you have any difculties obtaining
accessories for your appliance, please
contact the Philips Consumer Care Centre
in your country. You nd its contact details
in the worldwide guarantee leaet.
To retain the top performance of your shaver,
make sure you clean it regularly and replace
its shaving heads at the recommended time.
Shaving heads
- We advise you to replace your shaving
heads every two years. Always replace
them with Philips shaving heads only
(HQ4 for China or HQ56 for the rest
of the world) (Fig. 22).
Cleaning
- Use Philips Cleaning Spray (HQ110) to
clean the shaving heads thoroughly.
Environment
- Do not throw away the appliance
with the normal household waste at
the end of its life, but hand it in at an
ofcial collection point for recycling.
By doing this, you help to preserve the
environment (Fig. 23).
- The built-in rechargeable battery
contains substances that may pollute the
environment. Remove the battery before
you discard and hand in the appliance
at an ofcial collection point. Dispose
of the battery at an ofcial collection
point for batteries. If you have trouble
removing the battery, you can also take
the appliance to a Philips service centre.
The staff of this centre will remove the
battery for you and will dispose of it in an
environmentally safe way (Fig. 24).
Removing the rechargeable
battery
Only remove the rechargeable battery
when you discard the shaver. Make
sure the battery is completely empty
when you remove it.
1 Remove the adapter from the wall
socket and pull the micro USB plug
out of the shaver.
2 Let the shaver run until it stops and
undo the screw at the back of the
shaver (Fig. 25).
3 Remove the back panel of the shaver
with a screwdriver.
4 Remove the rechargeable battery.
Do not connect the shaver to the mains
again after you have removed the battery.
Guarantee and service
If you need service or information or if
you have a problem, please visit the Philips
website at www.philips.com/support or
contact the Philips Consumer Care Centre
in your country. You nd its phone number
in the worldwide guarantee leaet. If there
is no Consumer Care Centre in your
country, go to your local Philips dealer.
Guarantee restrictions
The shaving heads (cutters and guards) are
not covered by the terms of the international
guarantee because they are subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the
appliance. If you are unable to solve the
problem with the information below, visit
www.philips.com/support for a list of
frequently asked questions or contact the
Consumer Care Centre in your country.
Problem Possible
cause
Solution
The shaver
does not
shave as
well as it
used to.
The shaving
heads are
dirty. You
have not
cleaned the
shaver well
enough or
you have
not cleaned
it for a long
time.
Clean the
shaving heads
thoroughly
before you
continue
shaving. See
chapter
‘Cleaning and
maintenance’.
Long
hairs ob-
struct the
shaving
heads.
Clean the
cutters and
guards with
the clean-
ing brush
supplied.
See chapter
‘Cleaning and
maintenance’,
section ‘Every
two months:
shaving heads’.
You mixed
up the
cutters
and guards
when you
placed
them back
into the
retaining
frame after
cleaning.
Put each
cutter in the
other guard.
If you do not
switch the
cutters, it
may take
2 to 3 weeks
until optimal
shaving
performance
is restored.
- 請於 5°C 到 35°C 間充電、使用
並存放電鬍刀。
- 使用電鬍刀時，請勿搭配任何刮鬍
水、乳霜、乳液、凝露或其他其他
化妝品。
一般
- 轉換器可將 100-240 伏特的電壓轉
換為低於 24 伏特的安全低電壓。
符合標準
- 本飛利浦產品符合電磁波
(Electromagnetic fields，EMF) 所
有相關標準。只要使用方式正確並
依照本使用手冊之說明進行操作，
根據現有的科學研究資料，使用本
產品並無安全顧慮。
- 本電鬍刀符合適用的 IEC 安全標準。
充電
開始充電之前，務必將電鬍刀的電源
關閉。
當您第一次為電鬍刀充電，或長時間未
使用時，請連續充電 12 小時。一般充
電時間約需 8 個小時。
請在馬達停止轉動時或者運轉速度開始
變慢時，為產品充電。
為保持最佳效能，只有在電力不足時才
為電鬍刀充電。
請勿讓產品連續連接電源插座超過
24 小時。
1 將 micro USB 插頭放入電鬍刀
中。 (圖 3)
2 將轉換器插入插座。
, 充電指示燈亮起，表示產品正在進
行充電。 (圖 4)
注意： 請將電鬍刀充電至少滿
8 小時，但切勿超過 24 個小時。
3 電池完全充電後，請將轉換器自電
源插座拔下，並將 micro USB 插頭
自電鬍刀上拔下。 (圖 5)
注意： 電鬍刀無法插電運轉。電池耗盡
時，您必須先讓電池充電，才能再度使
用電鬍刀。
無線刮鬍時間
完全充電的電鬍刀可不插電刮鬍約
30 分鐘。
使用本產品
注意： 電鬍刀無法直接插電使用。
1 卸下保護蓋。
Problem Possible
cause
Solution
The shaving
heads are
damaged
or worn.
Replace
the shaving
heads. See
chapter ‘Re-
placement’.
The shaver
does not
work when
I press
the on/off
button.
The re-
chargeable
battery is
empty.
Recharge
the battery.
See chapter
‘Charging’.
My skin is
irritated
after shav-
ing.
Your skin
needs time
to get
used to
the Philips
shaving
system.
Skin irritation
during the
rst 2-3
weeks of use
is possible. Af-
ter this period,
the skin ir-
ritation usually
disappears.
The rota-
tion speed
of the shav-
ing heads is
slower than
usual.
Too much
dirt has
collected in
the shaving
heads.
Clean the
shaving heads.
See chapter
‘Cleaning and
maintenance’.
The re-
chargeable
battery is
low.
Recharge
the battery.
See chapter
‘Charging’.
The ap-
pliance
makes a
strange
noise.
Too much
dirt has
collected in
the shaving
heads.
Clean the
shaving heads.
After cleaning,
lubricate the
central point
on the inside
of the guards
with Philips
Cleaning Spray
(HQ110).
See chapter
‘Cleaning and
maintenance’.
The shaving
heads are
damaged
or worn.
Replace
the shaving
heads. See
chapter ‘Re-
placement’.
繁體中文
簡介
恭喜您購買本產品並歡迎加入飛利浦！
請於 www.philips.com/welcome 註冊您
的產品，以善用飛利浦提供的支援。
一般說明 (圖 1)
1 保護蓋
2 電鬍刀刀頭
3 電鬍刀組
4 鬍渣室
5 開/關 (On/Off) 按鈕
6 充電指示燈
7 micro USB 插頭用插座
8 固定架轉盤
9 固定架
10 刀具
11 刀網
12 釋放鈕
13 清潔刷
14 轉換器
15 Micro USB 插頭
16 收納袋 (僅限 PQ288)
17 飛利浦噴霧清潔劑 (HQ110) (選購)
重要事項
在使用本產品前，請先仔細閱讀本使用
手冊，並保留使用手冊以供日後參考。
危險
- 警告：本產品及電源轉換器請保持
乾燥。
- 此符號表示：禁止在水龍頭下清
洗。 (圖 2)
警示
- 轉換器內含一個變壓器。請勿切斷
轉換器而以其他插頭取代，否則會
造成危險。
- 警告：請勿在浴缸、淋浴間或其他
裝水容器附近使用本產品。
- 基於安全考慮，在缺乏監督及適當
指示之下，本產品不適用於孩童及
任何身體、知覺、或心理功能障礙
者，或缺乏使用經驗及知識者。
- 請勿讓孩童使用本產品或將本產品
當成玩具。
警告
- 電鬍刀或轉換器損壞時，請勿使用。
- 只能使用產品所附的電源轉換器為
產品充電。
- 如果轉換器損壞，請務必使用原型
號的轉換器進行更換，以免發生
危險。
1 關閉電鬍刀電源，將轉換器從電源
插座拔下，並將小插頭自電鬍刀上
拔下。
2 按下釋放鈕 (1) 並將電鬍刀組垂直
向上拉起，自電鬍刀上取下 (2)。
(圖 10)
3 逆時針方向轉動橘色轉盤 (1)，將固
定架拆下 (2)。 (圖 14)
4 一次取下並清洗一個刀頭。每個電
鬍刀刀頭都是由刀具和刀網組成。
(圖 15)
注意： 因為刀具及刀網是成對的一組，
請勿一次清潔超過一組。如果您不小心
將刀具及刀網混在一起，可能要花幾週
的時間才能恢復最理想的刮鬍效果。
5 取下刀具的刀網。 (圖 16)
6 請使用清潔刷的短毛側來清潔刀具。
請依箭頭方向小心刷動。 (圖 17)
7 請使用清潔刷的長毛側來清潔刀
網。 (圖 18)
8 清潔後，將刀具放回刀網中。
(圖 19)
9 將電鬍刀刀頭裝回電鬍刀組。 (圖 20)
10 將固定架裝回電鬍刀組 (1)，並以順
時針方向轉動橘色轉盤 (2)。 (圖 21)
11 將電鬍刀組裝回電鬍刀上。 (圖 13)
收納
請保持本產品乾燥。
請於 5°C 到 35°C 間使用並存放本
產品。
1 請關閉電鬍刀電源。
2 使用後請為電鬍刀蓋上保護蓋以防損
壞，並避免污垢累積在刀頭中。 (圖 8)
注意： 請確實將保護蓋的突耳蓋住釋
放鈕。
更換
每隔兩年更換一次電鬍刀刀頭，以確保
維持最佳的刮鬍效果。
損壞或用舊的刀頭限以飛利浦電鬍刀刀
頭替換 (中國為 HQ4+，其他國家/地區
為 HQ56)。
有關如何取下電鬍刀刀頭的說明，請參
閱「清潔與維護」單元之「每兩個月：
電鬍刀刀頭」章節。
2 按下開/關 (On/Off) 按鈕，開啟電鬍
刀電源。 (圖 6)
3 將電鬍刀刀頭在皮膚上移動，請同時
用直線及畫圓的方式來移動。 (圖 7)
注意： 僅可乾刮。使用電鬍刀時，請勿
搭配凝露、泡沫或水。
注意： 您的皮膚可能需要 2 到 3 週的
時間才能完全適應飛利浦電鬍刀系統。
4 按下開/關 (On/Off) 按鈕，關閉電鬍
刀電源。
5 每次刮鬍後，請清潔本電鬍刀 (請
參閱「清潔與維護」單元)。
6 為電鬍刀蓋上保護蓋以防損壞，並
避免污垢累積在刀頭中。 (圖 8)
注意： 請確實將保護蓋的突耳蓋住釋
放鈕。
清潔與維護
絕對不可使用鋼絲絨、磨蝕性的清潔劑
或侵蝕性的液體 (例如汽油或丙酮) 清潔
本產品。
在每次刮鬍之後清潔電鬍刀，以保障更好
的刮鬍效果。為達最好的清潔效果，建議
您使用飛利浦噴霧清潔劑 (HQ110)。請向
您的飛利浦經銷商洽詢相關資訊。
注意： 飛利浦電鬍刀刀頭噴霧清潔
劑 (HQ110) 並非所有國家/地區都有供
應。關於是否有這項配件供應，請與您
所在國家/地區的客戶服務中心聯繫。
每次刮鬍後：電鬍刀組與鬍渣室
1 關閉電鬍刀電源，將轉換器從電源
插座拔下，並將 micro USB 插頭自
電鬍刀上拔下。
2 使用隨附的清潔刷清潔產品上方。
(圖 9)
3 按下釋放鈕 (1) 並將電鬍刀組垂直
向上拉起，自電鬍刀上取下 (2)。
(圖 10)
4 使用隨附的清潔刷清潔電鬍刀組內
部。 (圖 11)
5 使用清潔刷清潔鬍渣室。 (圖 12)
6 將電鬍刀組裝回電鬍刀上。 (圖 13)
每兩個月：電鬍刀刀頭
注意： 請勿使用清潔劑或酒精清潔電
鬍刀刀頭，務必使用飛利浦噴霧清潔劑
(HQ110)。
保固與服務
若您需要相關服務或資訊，或是有任何
問題，請瀏覽飛利浦網站：
www.philips.com/support，或聯絡當地
的飛利浦客戶服務中心，您可以在全球保
證書上找到聯絡電話。若您當地沒有客戶
服務中心，請洽詢當地的飛利浦經銷商。
保固限制
電鬍刀刀頭 (刀具和刀網) 由於其耗損
性，因此不在全球保固範圍內。
故障排除
本章概述您使用本產品時最常遇到的問
題。如果您無法利用以下資訊解決您遇
到的問題，請造訪 www.philips.com/
support 查看常見問題清單，或聯絡您
所在國家/地區的飛利浦客戶服務中心。
問題 可能原因 解決方法
電鬍刀不
像平常
一樣運
作。
電鬍刀刀
頭不潔。
電鬍刀清
潔不夠徹
底或是太
久沒有清
潔。
在您繼續刮鬍
前，請徹底清
潔電鬍刀刀
頭。請參閱「
清潔與維護」
單元。
長鬍鬚卡
住電鬍刀
刀頭。
請使用隨附的
毛刷清潔刀具
及刀網。請參
閱「清潔與維
護」單元之「
每兩個月：電
鬍刀刀頭」章
節。
清潔刀具
及刀網
後，將其
放回固定
架時，把
刀具及刀
網混在一
起。
把每一片刀具
放入另一個刀
網。如果您沒
有調換刀具，
可能要花 2 到
3 週的時間才
能恢復最理想
的刮鬍效果。
電鬍刀刀
頭毀壞或
磨損。
更換電鬍刀刀
頭。請參閱「
更換」單元。
我按下
開/關
(On/Off)
按鈕時，
電鬍刀
沒有反
應。
充電電池
沒電。
為電池充電。
請參閱「充
電」單元。
訂購配件
如需購買本產品的配件，請造訪我們的線
上商店：www.shop.philips.com/service。
若您所在國家/地區沒有線上商店，請聯
絡您的飛利浦經銷商或飛利浦服務中心。
如果無法取得產品的配件，請聯絡您所在
國家/地區的飛利浦客戶服務中心。如需
詳細聯絡資料，請參閱全球保證書。
若要維持電鬍刀的最佳效能，請務必定
期清潔電鬍刀，並於建議的時間更換電
鬍刀刀頭。
電鬍刀刀頭
- 建議您每兩年即更換電鬍刀刀頭。
限以飛利浦電鬍刀刀頭替換 (中國為
HQ4，其他國家/地區為 HQ56)。
(圖 22)
清潔
- 使用飛利浦噴霧清潔劑 (HQ110) 徹
底清潔電鬍刀刀頭。
環境保護
- 本產品使用壽命結束時請勿與一般
家庭廢棄物一併丟棄。請將該產品
放置於政府指定的回收站，此舉能
為環保盡一份心力。 (圖 23)
- 本產品內建的充電電池可能含有污染
環境的物質。丟棄本產品或是將產品
放到政府指定的回收站前，請先取出
電池，並將電池送到政府指定的電池
回收站。若您無法取出電池，可將產
品拿到飛利浦服務中心，服務中心的
人員會為您卸下電池，並以無害環境
的方式處理電池。 (圖 24)
取出充電電池
棄置本電鬍刀前，請先取出充電電池。
當您要取出電池時，請確認其電力已完
全耗盡。
1 將轉換器自電源插座拔出，並將
micro USB 插頭從電鬍刀拔下。
2 讓電鬍刀持續運轉直到完全停止，然
後轉開電鬍刀背面的螺絲。 (圖 25)
3 用螺絲起子拆下電鬍刀的背板。
4 取出充電電池。
卸除電池後，請勿再次將電鬍刀連接
至電源。
問題 可能原因 解決方法
刮鬍之
後，皮膚
感到刺
痛。
您的皮膚
需要一些
時間才能
適應飛利
浦電鬍刀
系統。
開始使用的第
2 到 3 週，皮
膚可能會有過
敏現象。過了
這段時間，皮
膚過敏的症狀
通常會消失。
刀頭的旋
轉速度比
平常緩
慢。
過多污垢
累積在刀
頭中。
請清潔電鬍刀
刀頭。請參閱
「清潔與維
護」單元。
充電電池
電力不
足。
為電池充電。
請參閱「充
電」單元。
產品發出
奇怪的噪
音。
過多污垢
累積在刀
頭中。
請清潔電鬍刀
刀頭。清潔
後，請使用飛
利浦噴霧清潔
劑 (HQ110)
潤滑刀網內側
的中心點。請
參閱「清潔與
維護」單元。
電鬍刀刀
頭毀壞或
磨損。
更換電鬍刀刀
頭。請參閱「
更換」單元。
-
1
-
2
-
3
-
4
