ENGLISH
Introduction
Congratulations on your purchase and
welcome to Philips! To fully benet from
the support that Philips offers, register your
product at www.philips.com/welcome.
Important
Read this user manual carefully before you
use the appliance and save it for future
reference.
Danger
- Keep the adapter dry (Fig. 1).
Warning
- The adapter contains a transformer.
Do not cut off the adapter to replace
it with another plug, as this causes a
hazardous situation.
- The appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
- Children should be supervised to
ensure that they do not play with
the appliance.
- Always unplug the appliance before
you clean it under the tap.
Caution
- Never use water hotter than 80°C
to rinse the appliance.
- Do not use the appliance, adapter or
any other part if it is damaged, as this
may cause injury. Always replace a
damaged adapter or part with one of
the original type.
- Never use compressed air, scouring
pads, abrasive cleaning agents or
aggressive liquids such as petrol or
acetone to clean the appliance.
- Water may leak from the socket at the
bottom of the shaver when you rinse
it. This is normal and not dangerous
because all electronics are enclosed in
a sealed power unit inside the shaver.
Compliance with standards
- This shaver is waterproof and complies
with the internationally approved safety
regulations. It is suitable for use in
the bath or shower and for cleaning
under the tap. For safety reasons,
the shaver can therefore only be used
cordlessly (Fig. 2).
- This Philips appliance complies with all
applicable standards and regulations
regarding exposure to electromagnetic
elds.
General
- The adapter is equipped with an
automatic voltage selector and is
suitable for mains voltages ranging from
100 to 240 volts.
- The adapter transforms 100-240 volts
to a safe low voltage of less than 24 volts.
General description (Fig. 3)
1 Protection cap
2 Shaving unit with shaving head holder
3 Shaving head holder release buttons
4 On/off button
5 Display
6 Retaining ring
7 Cutter
8 Guard
9 Shaving head holder
10 Trimmer
11 Cleansing brush (specic types only)
12 Cleaning brush
13 Storage pouch
14 Adapter
15 Small plug
The display
’Charging’ indication
- When the shaver is charging, the
minutes indication ashes (Fig. 4).
- The shaving minutes increase until the
shaver is fully charged.
’Battery fully charged’ indication
- When the battery is fully charged,
the minutes indication is visible on
the display (Fig. 5).
- If you leave the shaver connected to
the mains, the display automatically
switches off after 30 minutes.
4222.002.5701.1
S575, S570
Register your product and get support at
www.philips.com/welcome
3
1
2
MINUTES LEFT
4
MINUTES LEFT
5
MINUTES LEFT
6
MINUTES LEFT
7
MINUTES LEFT
MINUTES LEFT
8 9
10
11
12 13
14
15 16
17
18 19
20 21
22
23
24 25
26
27 28
29
30 31
32 33
34
35
36 37
’Battery low’ indication
- When the battery is almost empty
(when there are only 5 or fewer
shaving minutes left), the minutes
indication and the plug symbol
start ashing (Fig. 6).
- When you switch off the shaver, the
shaving minutes and the plug symbol
continue to ash for a few more
seconds.
’Remaining battery capacity’
indication
- The remaining battery capacity is
indicated by the number of shaving
minutes shown on the display (Fig. 7).
- The remaining battery capacity is
shown when you switch the shaver on
or off.
Travel lock
You can lock the shaver when you are going
to travel. The travel lock prevents the shaver
from being switched on by accident.
Note: The travel lock cannot be activated
when the shaver is connected to the mains.
Activating the travel lock
1 Press and hold the on/off button until
the travel lock symbol stops ashing
and the motor stops running (Fig. 8).
The travel lock is now activated.
Note: If you release the on/off button before
the travel lock symbol stops ashing, the travel
lock is not activated.
Deactivating the travel lock
1 Press and hold the on/off button until
the travel lock symbol stops ashing
and the motor starts running.
The shaver is now ready for use again.
Note: When you start charging, the travel lock
is deactivated automatically.
Charging
It takes approx. 60 minutes to fully charge
the battery.
When you charge the shaver for the rst
time or after a long period of disuse,
let it charge for 90 minutes.
A fully charged shaver provides up to
50 shaving minutes.
If you have a heavy beard, the shaver may
provide less than 50 shaving minutes.
The number of shaving minutes may also
vary over time, depending on your shaving
behaviour, cleaning habits and beard type.
Charging for one shave
As the shaver charges, the display shows
the number of shaving minutes available.
Depending on the number of minutes
you usually need for one shave, you can
determine when the shaver contains
enough energy for one shave.
Charging
Do not charge the shaver in a closed
pouch or in the packaging.
1 Put the small plug in the shaver.
2 Put the adapter in the wall socket.
, The display shows that the shaver
is charging (see chapter ‘The display’).
Note: When you remove the adapter from
the wall socket and leave the small plug in
the shaver, the shaver may not work for a
few seconds.
Using the shaver
Note: You cannot use the shaver while it is
connected to the mains.
Shaving
Skin adaptation period
Your rst shaves may not bring you the
result you expect and your skin may even
become slightly irritated. This is normal.
Your skin and beard need time to adapt to
any new shaving system.
We advise you to shave regularly (at least
3 times a week) for a period of 3 weeks to
allow your skin to adapt to the new shaver.
During this period, use your new electric
shaver exclusively and do not use other
shaving methods. If you use different shaving
methods, it is more difcult for your skin to
adapt to the new shaving system.
1 Press the on/off button to switch on
the shaver.
2 Move the shaving heads over your
skin. Make both straight and circular
movements (Fig. 9).
3 Press the on/off button to switch off
the shaver.
4 Clean the shaver after every
shave (see chapter ‘Cleaning and
maintenance’).
Wet shaving
You can also use this shaver on a wet face
with shaving foam or shaving gel.
To shave with shaving foam or shaving gel,
follow the steps below:
1 Apply some water to your skin.
2 Apply shaving foam or shaving gel to
your skin.
3 Rinse the shaving unit under the tap
to ensure that the shaving unit glides
smoothly over your skin.
4 Press the on/off button to switch on
the shaver.
5 Move the shaving heads over your
skin. Make both straight and circular
movements.
Note: Rinse the shaver under the tap regularly
to ensure that it continues to glide smoothly
over your skin.
6 Dry your face and thoroughly rinse
the shaver with a sufcient amount
of water after every shave. Make sure
you rinse all foam or shaving gel off
the shaver (see also chapter ‘Cleaning
and maintenance’).
Trimming
You can use the trimmer to groom
your sideburns and moustache.
1 Pull the shaving unit straight off the
shaver (Fig. 10).
Note: Do not twist the shaving unit while you
pull it off the shaver.
2 Insert the lug of the trimmer into the
slot in the top of the shaver (1).
Then press down the trimmer (2) to
attach it to the shaver (‘click’) (Fig. 11).
3 Press the on/off button to switch
on the trimmer. You can now start
trimming.
4 Press the on/off button to switch off
the trimmer.
5 Pull the trimmer straight off the
shaver (Fig. 12).
Note: Do not twist the trimmer while you pull
it off the shaver.
6 Insert the lug of the shaving unit into
the slot in the top of the shaver
(1). Then press down the shaving
unit (2) to attach it to the shaver
(‘click’) (Fig. 13).
Facial cleansing and oil control
with cleansing brush (specic
types only)
Longer lasting oil control than manual
cleansing*. Simply click the brush on the
shaver and give your facial skin a 1 minute
deep clean, helping to deeply cleanse any
oil. The brush can be used in combination
with your own daily cleansing product.
The cleansing effect removes oil and dirt,
contributing to a healthy skin and oil free
feeling.
General warnings
- Do not clean the sensitive area around
your eyes.
- Do not use the appliance on chapped
skin, open wounds, or if you suffer from
skin diseases or skin irritations, such as
severe acne, sunburn, skin infection, etc.
- Do not use the appliance with self-
made cleansers or cleansers containing
harsh chemicals or rough particles.
- Do not use the appliance more than
twice a day.
1 Pull the shaving unit straight off the
shaver (Fig. 10).
Note: Do not twist the shaving unit while you
pull it off the shaver.
2 Insert the lug of the cleansing brush
into the slot in the top of the shaver
(1). Then press down the cleansing
brush (2) to attach it to the shaver
(‘click’) (Fig. 14).
3 Moisten the cleansing brush and your
face with warm water and cleansing
products.
Tip: Use the cleansing brush before shaving
for an easier shaving and a more hygienic
shaving result.
4 Press the on/off button to switch on
the appliance.
5 Start cleaning the T-zone with the
brush (Fig. 15).
Note: Make circular motions no more than
3 times in one spot.
6 Start cleaning the rest of your face.
Tip: Treat your face with the brush for about
one minute.
*compared to manual cleansing in the same
condition, according to the results from an
external test on 30 male Asian candidates
and in 3 hours after cleansing.
Cleaning and maintenance
Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive
liquids such as petrol or acetone to clean
the appliance and its accessories.
- Clean the shaver after every shave.
- Clean the shaving heads frequently
with Philips Shaving Head Cleaning
Spray (HQ110) for optimal shaving
performance.
- You can clean the outside of the
shaver with a damp cloth. Do not clean
the shaving unit with a cloth.
Cleaning the shaving unit
Be careful with hot water. Always check if
the water is not too hot, to prevent your
hands from getting burnt.
1 Switch off the shaver.
2 Rinse the shaving unit under a hot tap
for some time (Fig. 16).
Note: You can also clean the shaving unit with
the cleaning brush supplied.
3 After rinsing the appliance under the
tap, hold it upright for 10-15 seconds
to allow water to run out of the
bottom.
4 Press the release buttons on the
shaving unit (1) and pull the shaving
head holder off the shaving unit (2).
(Fig. 17)
5 Rinse the shaving head holder under a
hot tap for 30 seconds (Fig. 18).
Note: You can also clean the shaving head
holder with the cleaning brush supplied.
6 Carefully shake off excess water and
let the shaving head holder dry.
Never dry the shaving head holder with
a towel or tissue, as this may damage the
shaving heads.
7 Reattach the shaving head holder
to the shaving unit (‘click’) (Fig. 19).
Replacement
For maximum shaving performance, we
advise you to replace the shaving heads
every two years. Replace damaged shaving
heads right away.
Only replace the shaving heads with original
SH30 Philips shaving heads. See also chapter
‘Ordering accessories’.
1 Switch off the shaver.
2 Press the release buttons on the
shaving unit and pull the shaving head
holder off the shaving unit (Fig. 17).
3 Turn the retaining ring (1)
anticlockwise (2) and lift it off the
shaving head (3) (Fig. 20).
Repeat this process for the other retaining ring.
4 Remove the shavings heads from the
shaving head holder and throw them
away (Fig. 31).
5 Place new shaving heads in the
holder (Fig. 25).
Note: Make sure the projections of the
shaving heads t exactly into the recesses.
6 Place the retaining ring on the shaving
head (1) and turn it clockwise (2) to
reattach the retaining ring (Fig. 26).
The retaining ring is xed properly if the
two wings of the retaining ring are located
exactly under the projections of the shaving
head holder.
Repeat this process for the other retaining ring.
7 Reattach the shaving head holder to
the shaving unit (‘click’) (Fig. 19).
Note: If the shaving unit does not close
smoothly, check if you have positioned the
shaving heads properly and if the retaining
rings are xed properly.
Ordering accessories
To buy accessories or spare parts, visit
www.shop.philips.com/service or go
to your Philips dealer. You can also contact
the Philips Consumer Care Centre in your
country.
The following accessories are available:
- SH30 Philips shaving heads
- RQ575 Philips cleansing brush
attachment (specic types only)
- HQ110 Philips Shaving Head Cleaning
Spray(specic types only)
Extra-thorough cleaning method
1 Switch off the shaver.
2 Press the release buttons on the
shaving unit (1) and pull the shaving
head holder off the shaving unit (2)
(Fig. 17).
3 Turn the retaining ring anticlockwise
(1) and lift it off the shaving head (2)
(Fig. 20).
Repeat this process for the other retaining ring.
4 Remove the shaving heads from the
shaving head holder. Each shaving head
consists of a cutter and guard.
(Fig. 21)
Note: Do not clean more than one cutter and
guard at a time, since they are all matching
sets. If you accidentally put a cutter in the
wrong shaving guard, it may take several
weeks before optimal shaving performance
is restored.
5 Clean the cutter with the cleaning
brush supplied (Fig. 22).
6 Clean the inside of the guard. (Fig. 23)
7 After cleaning with the brush, clean
the cutter and guard under the tap
(Fig. 24).
8 Place the cutter back into the guard.
9 Put the shaving heads back into the
shaving head holder (Fig. 25).
Note: Make sure the projections of the
shaving heads t exactly into the recesses.
10 Place the retaining ring on the shaving
head (1) and turn it clockwise (2) to
reattach the retaining ring (Fig. 26).
The retaining ring is xed properly if the
two wings of the retaining ring are located
exactly under the projections of the shaving
head holder.
Repeat this process for the other retaining ring.
Note: The shaving heads and retaining ring
should be rmly set in place before closing
the shaving unit.
11 Reattach the shaving head holder to
the shaving unit (‘click’). (Fig. 19)
Note: If the shaving unit does not close
smoothly, check if you have positioned the
shaving heads properly and if the retaining
rings are xed properly.
Cleaning the trimmer
Clean the trimmer after every use.
Cleaning the trimmer under
the tap
1 Switch on the appliance with the
trimmer attached.
2 Rinse the trimmer under a hot tap for
some time. (Fig. 27)
3 After cleaning, switch off the appliance.
4 After rinsing the appliance under the
tap, hold it upright for 10-15 seconds
to allow water to run out of the
bottom.
Cleaning the trimmer with the
cleaning brush supplied
1 Switch off the trimmer.
2 Clean the trimmer with the cleaning
brush. Brush up and down along the
trimmer teeth. (Fig. 28)
Tip: For optimal trimmer performance,
lubricate the trimmer teeth frequently
with Philips Shaving Head Cleaning Spray
(HQ110).
Cleaning the cleansing brush
(specic types only)
1 Switch off the appliance.
2 Detach the brush head from the
brush base (Fig. 29).
3 Clean them thoroughly with warm
water and soap.
4 Dry the brush head with a towel.
Storage
Note: Make sure the appliance and the
attachments are dry before you store them.
1 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 30).
2 Store the shaver in the
pouch supplied.
3 Specic types only: Put the protection
cap on the brush head to protect it
from dirt accumulation.
Guarantee and support
If you need information or support, please
visit www.philips.com/support or read
the separate worldwide guarantee leaet.
Guarantee restrictions
The shaving heads (cutters and guards)
are not covered by the terms of the
international guarantee because they are
subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the
appliance. If you are unable to solve the
problem with the information below, visit
www.philips.com/support for a list of
frequently asked questions or contact the
Consumer Care Centre in your country.
Problem Possible
cause
Solution
The
shaver
does not
shave as
well as it
used to.
The shaving
heads are
damaged or
worn.
Replace the
shaving heads
(see chapter
‘Replace-
ment’).
The shaving
heads are
dirty.
Clean the
cutters and
guards with
the clean-
ing brush
supplied
(see chapter
‘Cleaning and
maintenance’,
section
‘Extra-thor-
ough cleaning
method’).
Long hairs
obstruct
the shaving
heads.
Clean the
cutters and
guards with
the clean-
ing brush
supplied
(see chapter
‘Cleaning and
maintenance’,
section
‘Extra-thor-
ough cleaning
method’).
- RQ560 Philips oil-control cleansing
brush head (single pack) replacement
(specic types only)
- RQ560 Philips oil-control cleansing
brush head (triple pack) replacement
(specic types only)
- RQ575 Philips oil-control cleansing
brush head (specic types only)
- RQ585 Philips oil-control cleansing
brush head pro (specic types only)
Recycling
- Do not throw away the appliance
with the normal household waste at
the end of its life, but hand it in at an
ofcial collection point for recycling.
By doing this, you help to preserve the
environment (Fig. 32).
- The built-in rechargeable shaver battery
contains substances that may pollute
the environment. Always remove the
battery before you discard or hand in
the shaver at an ofcial collection point.
Dispose of the battery at an ofcial
collection point for batteries. If you
have trouble removing the battery, you
can also take the appliance to a Philips
service centre. The staff of this centre
will remove the battery for you and will
dispose of it in an environmentally safe
way (Fig. 33).
Removing the rechargeable
shaver battery
Only remove the rechargeable battery
when you discard the shaver. Make sure
the rechargeable battery is completely
empty when you remove it.
Be careful, the battery strips are sharp.
1 Undo the screw in the back panel of
the shaver with a screwdriver (1) and
remove the back panel (2) (Fig. 34).
2 Bend the hooks aside and remove the
power unit (Fig. 35).
3 Break the snap hooks (1) and remove
the front panel of the power unit
(2) (Fig. 36).
4 Take out the battery holder (1) and
cut the battery tags with a pair of
cutting pliers (2) (Fig. 37).
5 Remove the rechargeable battery.
Problem Possible
cause
Solution
The
shaver
does not
work,
even
though
it is con-
nected
to the
mains.
This shaver is
not designed
to be used
directly from
the mains.
Remove
the adapter
from the
wall socket
and the small
plug from
the shaver.
You can now
switch on the
shaver again.
My
skin is
irritated
after
shaving.
Your skin
needs time
to get used
to the Philips
shaving
system.
Skin irritation
during the rst
2-3 weeks of
use is pos-
sible. After this
period, the
skin irritation
usually disap-
pears.
The shaving
heads are
damaged or
worn.
Replace the
shaving heads
(see chapter
‘Replace-
ment’).
The
rotation
speed
of the
shaving
heads
is lower
than
usual.
Too much
dirt has
collected in
the shaving
heads.
Clean the
shaving heads.
See chapter
‘Cleaning and
maintenance’.
The re-
chargeable
battery is
low.
Recharge
the battery.
See chapter
‘Charging’.
The
shaving
heads do
not stay
in place.
You did not
x the retain-
ing rings
properly.
The retaining
ring is xed
properly
if the two
wings of the
retaining ring
are located
exactly under
the projec-
tions of the
shaving head
holder.
Problem Possible
cause
Solution
Shaving foam
or shaving
gel has ac-
cumulated in
the shaving
heads.
Rinse the
shaving heads
thoroughly
with a suf-
cient amount
of water.
The
shaver
does not
work
when I
press the
on/off
button.
The re-
chargeable
battery is
empty.
Recharge
the battery
(see chapter
‘Charging’).
The travel
lock is acti-
vated.
To deactivate
the travel
lock, press
and hold the
on/off button
until the
travel lock
symbol stops
ashing and
the motor
starts run-
ning.
The tem-
perature of
the shaver is
too high. In
this case, the
shaver does
not work.
Let the
shaver cool
down. As
soon as the
temperature
of the shaver
has dropped
sufciently,
you can
switch on the
shaver again.
When you
remove the
adapter from
the wall sock-
et and leave
the small plug
in the shaver,
the shaver
does not
work for a
few seconds.
Remove the
small plug
from the
shaver.
- 當您關閉電鬍刀的電源時，可使
用時間及插頭符號會繼續閃爍幾
秒鐘。
「剩餘電池電量」指示
- 電池剩餘的電量是以螢幕中顯示的
可使用分鐘數來表示。 (圖 7)
- 開/關電鬍刀電源時，會顯示剩餘電
池電量。
旅行鎖定
在您外出旅行之前，可以設定鎖住電鬍
刀。使用旅行鎖可防止電鬍刀意外開
啟電源。
注意： 電鬍刀插接電源時無法啟動旅
行鎖定。
啟動旅行鎖
1 按住開關 (on/off) 按鈕直到旅行鎖
定符號停止閃爍，且馬達停止運轉
為止。 (圖 8)
這時即已啟動旅行鎖定。
注意： 若您在旅行鎖定符號停止閃爍
前放開開關 (on/off) 按鈕，則旅行鎖定
不會啟動。
解除旅行鎖
1 按住開關 (on/off) 按鈕直到旅行鎖
定符號停止閃爍，且馬達開始運轉
為止。
電鬍刀現在已可再度使用。
注意： 一開始充電就會自動解除旅行
鎖定。
充電
完整充電約需 60 分鐘。
在您第一次對電鬍刀充電或者長時間沒
有使用後，請讓它連續充電 90 分鐘。
充飽電的電鬍刀可刮鬍 50 分鐘。
若您的鬢鬚濃密，電鬍刀的刮鬍時間可
能少於 50 分鐘。此外，取決於您的刮
鬍方式、清潔習慣和鬍鬚類型，可使用
時間也可能會隨著時日改變。
充足一次刮鬍所需電力
電鬍刀充電時會在螢幕顯示可使用分鐘
數。您可以依據平常刮鬍所需時間來判
斷電力是否足夠刮鬍一次。
充電
請勿將電鬍刀置於密閉收納袋中或在包
裝內充電。
1 將小插頭插上電鬍刀。
2 將轉換器插入插座。
- 絕對不可使用壓縮空氣、鋼絲絨、
磨蝕性的清潔劑或侵蝕性的液體
(例如汽油或丙酮) 清潔本產品。
- 在您沖洗時，水可能會從電鬍刀底
部的插孔流出。此為正常現象，不
會造成危險，因為所有的電子零件
都密封於電鬍刀內的電源裝置中。
符合標準
- 這款防水電鬍刀符合國際公認的安
全規範。適合在泡澡或淋浴時使
用，且可在水龍頭底下清潔。基於
安全考量，本電鬍刀只能以無線方
式操作。 (圖 2)
- 本飛利浦產品符合所有電磁波暴露
的相關適用標準和法規。
一般
- 本轉換器配備有自動電壓選擇器，
適用 100 到 240 伏特的插座電壓。
- 轉換器可將 100-240 伏特的電壓轉
換為低於 24 伏特的安全低電壓。
一般說明 (圖 3)
1 保護蓋
2 附電鬍刀刀頭固定座的電鬍刀組
3 電鬍刀刀頭固定座釋放鈕
4 開關按鈕
5 顯示幕
6 固定環
7 刀具
8 刀網
9 電鬍刀刀頭固定座
10 鬢角刀
11 潔顏刷 (限特定機型)
12 清潔刷
13 收納袋
14 轉換器
15 小插頭
顯示畫面
「充電」指示燈
- 電鬍刀充電中時，可使用時間指示
燈會閃爍。 (圖 4)
- 可使用時間會持續增加，至電鬍刀
充飽電力為止。
「電池充滿電」指示燈
- 當電池充飽電力後，螢幕會顯示可
使用時間指示燈。 (圖 5)
- 如果您將電鬍刀連接至電源時，
螢幕會在 30 分鐘後自動關閉。
「電量不足」指示
- 電池電力即將用盡 (可使用時間只
剩 5 分鐘以內) 時，可使用時間及
插頭符號會開始閃爍。 (圖 6)
Problem Possible
cause
Solution
After
fully
charg-
ing the
shaver, it
provides
less
than 50
shaving
minutes.
If you have a
heavy beard,
the shaver
may provide
less than
50 shaving
minutes.
The number
of shaving
minutes may
also vary
over time,
depending on
your shaving
behaviour,
cleaning hab-
its and beard
type.
繁體中文
簡介
恭喜您購買本產品並歡迎加入飛利浦！
請於 www.philips.com/welcome 註冊您
的產品，以善用飛利浦提供的支援。
重要事項
在使用本產品前，請先仔細閱讀本使用
手冊，並保留使用手冊以供日後參考。
危險
- 請保持轉換器乾燥。 (圖 1)
警示
- 轉換器內含一個變壓器。請勿切斷
轉換器而以其他插頭取代，否則會
造成危險。
- 本產品不適合供下列人士 (包括小
孩) 使用：身體官能或心智能力退
化者，或是經驗與使用知識缺乏
者。他們需要有負責其安全的人員
在旁監督，或指示產品的使用方
法，方可使用。
- 請勿讓孩童使用本產品或將本產品
當成玩具。
- 在水龍頭下沖洗本產品之前，
請先拔掉產品電源插頭。
警告
- 切勿使用超過 80°C 的熱水沖洗
產品。
- 如有損壞情況，請勿繼續使用該產
品、轉換器或任何其他零件，否則
可能導致受傷。轉換器或零件如有
受損，請務必以原型號更換之。
, 螢幕會顯示電鬍刀正充電中 (請參
閱「顯示畫面」單元)。
注意： 當您將轉換器從電源插座拔除
時，小插頭若仍插在電鬍刀上，電鬍刀
可能有幾秒鐘無法運作。
使用本電鬍刀
注意： 您無法在電鬍刀仍連接在電源
上時使用。
刮鬍
皮膚適應期
您第一次刮鬍的結果可能不如您所預
期，皮膚甚至可能稍微刺痛。這是正常
現象。您的皮膚與鬍鬚需要時間適應任
何新的刮鬍系統。
我們建議您定期刮鬍 (每週至少 3 次)
為期 3 週，讓您的肌膚適應新的電鬍
刀。這段期間，請只使用您的新電鬍
刀，不要使用其他的刮鬍方式。如果您
使用不同的刮鬍方式，您的皮膚可能較
難適應新的刮鬍系統。
1 按下開/關 (On/Off) 按鈕，開啟電鬍
刀電源。
2 將電鬍刀刀頭在皮膚上移動，
請同時用直線及畫圓的方式來移動。
(圖 9)
3 按下開/關 (On/Off) 按鈕，關閉電鬍
刀電源。
4 每次刮鬍後，請清潔本電鬍刀
(請參閱「清潔與維護」單元)。
濕刮
您也可以在沾有刮鬍膏或刮鬍凝露的濕
潤臉部上使用本電鬍刀。
若要在刮鬍時配合使用刮鬍泡或刮鬍凝
膠，請依照下列步驟：
1 在皮膚上抹一點水。
2 將刮鬍泡或刮鬍凝膠抹到皮膚上。
3 將電鬍刀組放在水龍頭下沖洗，
以確保電鬍刀組能在皮膚上平順
移動。
4 按下開/關 (On/Off) 按鈕，開啟電鬍
刀電源。
5 將電鬍刀刀頭在皮膚上移動，請同
時用直線及畫圓的方式來移動。
注意： 定期將電鬍刀放在水龍頭下沖洗，
以確保電鬍刀持續在皮膚上平順移動。
11 將電鬍刀刀頭固定座重新接上電鬍刀
組 (會聽見「喀噠」一聲)。 (圖 19)
注意： 若電鬍刀組無法順利關上，
請檢查電鬍刀刀頭安裝位置是否正確，
以及固定環是否確實固定。
清潔鬢角刀
每次使用後均需清潔鬢角刀。
將鬢角刀放在水龍頭下沖洗
1 裝上鬢角刀後，開啟產品電源。
2 將鬢角刀以熱水沖洗一段時間。
(圖 27)
3 清潔之後，關閉產品電源。
4 在水龍頭下沖洗本產品，將其直立
10-15 秒，讓水從底部流出。
使用隨附的清潔刷來清潔鬢角刀
1 關閉鬢角刀電源。
2 使用清潔刷清潔鬢角刀。請沿著鬢
角刀的刀齒上下地刷。 (圖 28)
提示： 為使鬢角刀發揮最佳性能，
請經常使用飛利浦電鬍刀刀頭噴霧清潔
劑 (HQ110) 潤滑鬢角刀的刀齒。
清潔潔顏刷 (限特定機型)
1 關閉產品。
2 將刷頭從刷頭底座上拆下。 (圖 29)
3 使用溫水及肥皂徹底清潔。
4 以毛巾擦乾刷頭。
收納
注意： 收納前，請確保產品與配件乾燥。
1 使用後請為電鬍刀蓋上保護蓋以防
損壞，並避免污垢累積在電鬍刀刀
頭中。 (圖 30)
2 將電鬍刀存放在隨附的收納袋中。
3 限特定機型：蓋上刷頭保護蓋，
以防污垢累積。
更換
為得到最佳的刮鬍性能，我們建議您請
每兩年更換一次電鬍刀刀頭。有損傷的
電鬍刀刀頭則請要立即更換。
更換電鬍刀刀頭時，限使用原廠 SH30
飛利浦電鬍刀刀頭。亦請參閱「訂購配
件」單元。
1 請關閉電鬍刀電源。
注意： 您也可以用產品所附的清潔刷清
潔電鬍刀刀頭固定座。
6 仔細甩乾多餘的水份之後，讓電鬍
刀刀頭固定座乾燥。
切勿使用毛巾或紙巾擦乾電鬍刀刀頭固
定座，因為此舉可能會造成電鬍刀刀
頭損害。
7 將電鬍刀刀頭固定座重新接上電鬍刀
組 (會聽見「喀噠」一聲)。 (圖 19)
超徹底清潔方法
1 請關閉電鬍刀電源。
2 按下電鬍刀組的釋放鈕 (1) 並將電鬍
刀刀頭固定座從電鬍刀組取下 (2)。
(圖 17)
3 將固定環以逆時針方向轉動 (1)，
然後將其自電鬍刀刀頭拿起 (2)。
(圖 20)
就其他固定環重複此項程序。
4 從電鬍刀刀頭固定座上取下電鬍刀
刀頭。每個電鬍刀刀頭均含刀片和
刀網。 (圖 21)
注意： 因為刀片及刀網是成對的一組，
請勿一次清潔多組。如果您不小心將
刀片放進錯誤的電鬍刀刀網中，可能
要花幾週的時間才能恢復最理想的刮
鬍效果。
5 使用隨附於電鬍刀的清潔刷來清潔
刀片。 (圖 22)
6 清潔刀網內部。 (圖 23)
7 以小刷子清潔之後，將刀片及刀網
置於水龍頭下沖洗。 (圖 24)
8 將刀片放回刀網中。
9 將電鬍刀刀頭裝回電鬍刀刀頭固
定座。 (圖 25)
注意： 確定電鬍刀刀頭的凸出部分準確
地安裝於凹處。
10 將固定環放在電鬍刀刀頭上 (1)
並以順時針方向轉動 (2)，以重新裝
回固定環。 (圖 26)
若固定環的兩翼已準確崁入電鬍刀刀頭
固定座的凸出部分下方，則表示固定環
已正確固定。
就其他固定環重複此項程序。
注意： 應先確定電鬍刀刀頭和固定環已
妥善固定，再關閉電鬍刀組。
2 將潔顏刷的突耳插入電鬍刀頂端的
凹槽 (1)，再將潔顏刷 (2) 往下壓，
即可安裝到電鬍刀上 (會聽見「喀
噠」一聲)。 (圖 14)
3 以溫水和清潔產品潤溼潔顏刷與
臉部。
提示： 除毛前如先使用潔顏刷，可更輕
鬆達到衛生的除毛效果。
4 按下開/關 (On/Off) 按鈕，開啟產品
電源。
5 使用刷具開始清潔 T 字部位。
(圖 15)
注意： 以畫圓的方式清潔，每個區塊不
要超過 3 次。
6 開始清潔臉部其餘部位。
提示： 使用刷具清潔臉部約 1 分鐘。
* 經外部機構針對 30 名亞洲男性進行清
潔後 3 小時的狀況進行測試，與相同狀
況下用手清潔的比較結果。
清潔與維護
絕對不可使用壓縮空氣、鋼絲絨、磨蝕
性的清潔劑或侵蝕性的液體 (例如汽油
或丙酮) 清潔本產品與其配件。
- 每次刮鬍後均需清潔電鬍刀。
- 為得到最佳的刮鬍性能，請經常使
用飛利浦電鬍刀刀頭噴霧清潔劑
(HQ110) 清潔電鬍刀刀頭。
- 您可以使用濕布清潔電鬍刀外側。
請勿用布清潔電鬍刀組。
清洗電鬍刀組
請小心使用熱水。隨時檢查熱水是否太
燙，以避免手部燙傷。
1 請關閉電鬍刀電源。
2 將電鬍刀組以熱水沖洗一段時間。
(圖 16)
注意： 您也可以用產品所附的清潔刷清
潔電鬍刀組。
3 在水龍頭下沖洗本產品，將其直立
10-15 秒，讓水從底部流出。
4 按下電鬍刀組的釋放鈕 (1) 並將電鬍
刀刀頭固定座從電鬍刀組取下 (2)。
(圖 17)
5 將電鬍刀刀頭固定座放在熱水龍頭
下沖洗 30 秒。 (圖 18)
6 每次刮鬍，請擦乾臉部，並使用足
量的水徹底沖洗電鬍刀。請確實從
電鬍刀上洗去所有刮鬍膏或刮鬍凝
露 (請參閱「清潔與維護」單元)。
修剪
您可以使用鬢角刀修整鬢角與鬍髭。
1 從電鬍刀中垂直抽出電鬍刀組。
(圖 10)
注意： 當您從電鬍刀中抽出電鬍刀組時，
請勿旋轉。
2 將鬢角刀的突耳插入電鬍刀頂端
的凹槽 (1)，再將鬢角刀往下壓 (2)
即可安裝到電鬍刀上 (會聽見「喀
噠」一聲)。 (圖 11)
3 按下開關 (on/off) 按鈕，開啟鬢角
刀電源。這時即可開始修整。
4 按下開關 (on/off) 按鈕，關閉鬢角
刀電源。
5 從電鬍刀中垂直抽出鬢角刀。
(圖 12)
注意： 當您從電鬍刀中抽出鬢角刀時，
請勿旋轉。
6 將電鬍刀組的突耳插入電鬍刀頂端
的凹槽 (1)，再將電鬍刀組往下壓
(2) 即可安裝到電鬍刀上 (會聽見
「喀噠」一聲)。 (圖 13)
潔面控油的潔顏刷 (限特定機型)
比用手清潔更能長效控油*。只需輕按
電鬍刀上的刷具，即可深層清潔臉部肌
膚 1 分鐘，有助於深入清潔油脂。刷具
可以搭配自己的日常清潔產品使用。清
潔效果可去除油脂與污垢，讓肌膚健康
清爽不油膩。
一般警告
- 請勿清潔眼睛周圍的敏感部位。
- 請勿將本產品用於乾裂的皮膚和開
放性的傷口上，或者，如果您患有
皮膚病或皮膚刺痛，例如嚴重的粉
刺、曬傷、皮膚感染等，也請勿使
用本產品。
- 請勿將本產品與自製洗面乳或含有
刺激性化學物質或較粗顆粒的洗面
乳一起搭配使用。
- 一天請勿使用本產品超過兩次。
1 從電鬍刀中垂直抽出電鬍刀組。
(圖 10)
注意： 當您從電鬍刀中抽出電鬍刀組時，
請勿旋轉。
問題 可能原因 解決方法
電鬍刀
充飽電
後，可
提供的
刮鬍時
間少於
50 分
鐘。
若您的鬢鬚
濃密，電鬍
刀的刮鬍時
間可能少於
50 分鐘。
此外，取決
於您的刮鬍
方式、清潔
習慣和鬍鬚
類型，可使
用時間也可
能會隨著時
日改變。
問題 可能原因 解決方法
當您將轉換
器從電源插
座拔除時，
小插頭若仍
插在電鬍刀
上，電鬍刀
會有幾秒鐘
無法運作。
將小插頭從
電鬍刀取
下。
電鬍刀
無法運
作，即
使已經
連接到
電源。
此電鬍刀無
法直接插電
使用。
將轉換器從
電源插座拔
除，並將小
插頭從電鬍
刀上取下。
現在您可以
再次開啟電
鬍刀的電
源。
刮鬍之
後，皮
膚感到
刺痛。
您的皮膚需
要一些時間
才能適應飛
利浦電鬍刀
系統。
開始使用的
第 2 到
3 週，皮膚
可能會有過
敏現象。
過了這段時
間，皮膚過
敏的症狀通
常會消失。
電鬍刀刀頭
毀壞或磨
損。
更換電鬍刀
刀頭 (請參
閱「更換」
單元)。
電鬍刀
刀頭的
旋轉速
度比平
常緩
慢。
過多污垢累
積在電鬍刀
刀頭中。
請清潔電鬍
刀刀頭。請
參閱「清潔
與維護」單
元。
充電式電池
電力不足。
為電池充
電。請參閱
「充電」單
元。
電鬍刀
刀頭不
穩固。
固定環未妥
善固定。
若固定環的
兩翼已準確
崁入電鬍刀
刀頭固定座
的凸出部分
下方，則表
示固定環已
正確固定。
問題 可能原因 解決方法
電鬍刀
不像平
常一樣
運作。
電鬍刀刀頭
毀壞或磨
損。
更換電鬍刀
刀頭 (請參
閱「更換」
單元)。
電鬍刀刀頭
髒污。
使用隨附的
清潔刷清潔
刀具及刀網
(請參閱「清
潔與維護」
單元的「超
徹底清潔方
法」小節)。
長鬍鬚卡住
電鬍刀刀
頭。
使用隨附的
清潔刷清潔
刀具及刀網
(請參閱「清
潔與維護」
單元的「超
徹底清潔方
法」小節)。
刮鬍泡或刮
鬍凝膠黏附
在電鬍刀刀
頭上。
以足量的水
徹底沖洗電
鬍刀刀頭。
我按下
開/關
(On/
Off) 按
鈕時，
電鬍刀
沒有反
應。
充電式電池
沒電。
將電池重新
充電 (請參
閱「充電」
單元)。
旅行鎖定已
啟動。
若要解除旅
行鎖定，按
住開關 (on/
off) 按鈕直
到旅行鎖定
符號停止閃
爍，且馬達
開始運轉為
止。
電鬍刀過
熱。在此情
況下，電鬍
刀將無法使
用。
讓電鬍刀冷
卻。等到電
鬍刀充分降
溫，您就能
再度啟動電
鬍刀的電
源。
回收
- 本產品使用壽命結束時請勿與一般
家庭廢棄物一併丟棄。請將該產品
放置於政府指定的回收站，此舉能
為環保盡一份心力。 (圖 32)
- 本電鬍刀使用的充電式電池可能含
有會污染環境的物質。將本電鬍刀
丟棄或是送到政府指定回收站前，
請務必先取出電池，並將電池送到
政府指定的電池回收站。若您無法
取出電池，也可將本產品帶到飛利
浦授權服務中心。服務中心會為您
卸下電池，並以對環境無害的方式
處理電池。 (圖 33)
取出電鬍刀的充電式電池
棄置本電鬍刀前，請先取出充電式電
池。當您要取出充電式電池時，請確認
其電力已完全耗盡。
電池固定帶非常銳利，請小心。
1 用螺絲起子 (1) 轉開電鬍刀的背板
螺絲，拆下背板 (2)。 (圖 34)
2 彎折旁邊的扣鉤，然後取出供電
裝置。 (圖 35)
3 斷開彈簧鉤 (1)，並取下供電裝置的
正面護板 (2)。 (圖 36)
4 取出電池固定座 (1) 並使用剪鉗 (2)
將電池拉片剪斷。 (圖 37)
5 取出充電式電池。
保固與支援
如果您需要資訊或支援，請造訪：
www.philips.com/support，或另行參閱
全球保證書。
保固限制
電鬍刀刀頭 (刀具和刀網) 由於其耗損
性，因此不在全球保固範圍內。
疑難排解
本單元概述您使用本產品時最常遇到的
問題。如果您無法利用以下資訊解決您
遇到的問題，請造訪 www.philips.com/
support 查看常見問題清單，或聯絡您
所在國家/地區的飛利浦客戶服務中心。
2 按下電鬍刀組的釋放鈕，將電鬍刀刀
頭固定座從電鬍刀組取下。 (圖 17)
3 將固定環 (1) 以逆時針方向旋轉 (2)，
然後將其自電鬍刀刀頭拿起 (3)。
(圖 20)
就其他固定環重複此項程序。
4 從電鬍刀刀頭固定座上取下電鬍刀
刀頭並丟棄。 (圖 31)
5 將新的電鬍刀刀頭放入固定座。
(圖 25)
注意： 確定電鬍刀刀頭的凸出部分準確
地安裝於凹處。
6 將固定環放在電鬍刀刀頭上 (1)
並以順時針方向轉動 (2)，以重新裝
回固定環。 (圖 26)
若固定環的兩翼已準確崁入電鬍刀刀頭
固定座的凸出部分下方，則表示固定環
已正確固定。
就其他固定環重複此項程序。
7 將電鬍刀刀頭固定座重新接上電鬍刀
組 (會聽見「喀噠」一聲)。 (圖 19)
注意： 若電鬍刀組無法順利關上，
請檢查電鬍刀刀頭安裝位置是否正確，
以及固定環是否確實固定。
訂購配件
若要購買配件或備用零件，請造訪
www.shop.philips.com/service，或者洽
詢您的飛利浦經銷商。您也可以聯絡您
所在國家/地區的飛利浦客戶服務中心。
備有下列配件可供另外選購：
- SH30 飛利浦電鬍刀刀頭
- RQ575 飛利浦潔顏刷配件
(限特定機型)
- HQ110 飛利浦電鬍刀刀頭噴霧清潔
劑 (限特定機型)
- RQ560 飛利浦控油潔顏刷頭
(單組裝) 更換配件 (限特定機型)
- RQ560 飛利浦控油潔顏刷頭
(3入裝) 更換配件 (限特定機型)
- RQ575 飛利浦控油潔顏刷頭
(限特定機型)
- RQ585 飛利浦控油潔顏刷頭
(專業級) (限特定機型)
-
1
-
2
-
3
-
4
-
5
-
6
