ENGLISH
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benet from the support that Philips
offers, register your product at www.philips.com/
welcome.
Important safety information
Read this important information carefully before
you use the appliance and its accessories and save
it for future reference. The accessories supplied
may vary for different products.
Danger
- Keep the adapter dry (Fig. 1).
Warning
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug,
as this causes a hazardous situation.
- This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
- Children should be supervised to ensure that
they do not play with the appliance.
- Always unplug the shaver before you clean it
under the tap.
- Always check the appliance before you use
it. Do not use the appliance if it is damaged,
as this may cause injury. Always replace a
damaged part with one of the original type.
Caution
- Never use water hotter than 80°C to rinse
the shaver.
- Only use this appliance for its intended
purpose as shown in the user manual.
- For hygienic reasons, the appliance should only
be used by one person.
- Do not use the adapter in or near wall sockets
that contain or have contained an electric air
freshener to prevent irreparable damage to
the adapter.
- Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the appliance.
- Remove the detachable cord from the handheld
part before cleaning this part in water.
4222.002.5426.3
RQ352, RQ350, RQ338, RQ331,
RQ330, RQ311
Register your product and get support at
www.philips.com/welcome
3
1 2 4
5 6 7
8 9 10
11 12 13
14 15 16
17 18 19
20 21 22
23 24 25
26 27 28
29 30 31
- Water may drip from the socket at the bottom
of the shaver when you rinse it. This is normal
and not dangerous because all electronics
are enclosed in a sealed power unit inside
the shaver.
Electromagnetic elds (EMF)
- This Philips appliance complies with all
applicable standards and regulations regarding
exposure to electromagnetic elds.
General
- This shaver is waterproof. It is suitable for use
in the bath or shower and for cleaning under
the tap. For safety reasons, the shaver can
therefore only be used without cord (Fig. 2).
- The appliance is suitable for mains voltages
ranging from 100 to 240 volts.
- The adapter transforms 100-240 volts to
a safe low voltage of less than 24 volts.
- Maximum noise level: Lc = 69dB(A)
General description (Fig. 3)
1 Protection cap
2 Shaving unit with shaving head holder
3 Shaving head holder release buttons
4 On/off button
5 ’Battery low’ light
6 Retaining ring
7 Cutter
8 Shaving guard
9 Shaving head holder
10 Trimmer (RQ350 only)
11 Adapter
12 Charging light
13 Small plug
14 Cleaning brush
Charging
It takes approx. 10 hours to fully charge the battery.
A fully charged shaver provides up to 30 shaving
minutes.
If you have a heavy beard, the shaver may
provide less than 30 shaving minutes. The number
of shaving minutes may also vary over time,
depending on your shaving behaviour, cleaning
habits and beard type.
’Charging’ indication
- When the shaver is charging, the light on the
adapter lights up (Fig. 4).
’Battery low’ light
- When the battery is almost empty, the light on
the shaver lights up (Fig. 5).
Charging
Do not charge the shaver in the packaging.
1 Put the small plug in the shaver.
2 Put the adapter in the wall socket.
, The light on the adapter lights up to show
that the shaver is charging.
Note: The light on the adapter does not change colour
and does not go out when the shaver is fully charged.
Using the shaver
Note: You cannot use the shaver while it is connected
to the mains.
Shaving
Skin adaptation period
Your rst shaves may not bring you the result you
expect and your skin may even become slightly
irritated. This is normal. Your skin and beard need
time to adapt to any new shaving system.
We advise you to shave regularly (at least 3 times
a week) for a period of 3 weeks to allow your skin
to adapt to the new shaver. During this period, use
your new electric shaver exclusively and do not use
other shaving methods. If you use different shaving
methods, it is more difcult for your skin to adapt
to the new shaving system.
1
Press the on/off button to switch on the shaver.
2 Move the shaving heads over your skin.
Make both straight and circular movements
(Fig. 6).
3
Press the on/off button to switch off the shaver.
4 Clean the shaver after every shave
(see chapter ‘Cleaning and maintenance’).
Trimming (RQ350 only)
You can use the trimmer to groom your sideburns
and moustache.
1 Pull the shaving unit straight off the shaver
(Fig. 7).
Note: Do not twist the shaving unit while you pull it
off the shaver.
2 Insert the lug of the trimmer into the slot in
the top of the shaver (1). Then press down
the trimmer (2) to attach it to the shaver
(‘click’) (Fig. 8).
3 Press the on/off button to switch on the
trimmer. You can now start trimming.
4 Press the on/off button to switch off
the trimmer.
5 Pull the trimmer straight off the shaver
(Fig. 9).
Note: Do not twist the trimmer while you pull it off
the shaver.
6 Insert the lug of the shaving unit into the slot
in the top of the shaver (1). Then press down
the shaving unit (2) to attach it to the shaver
(‘click’) (Fig. 10).
Cleaning and maintenance
Detach the handheld part from the supply cord
before cleaning it in water.
Never use scouring pads, abrasive cleaning agents
or aggressive liquids such as petrol or acetone to
clean the shaver and its accessories.
- Clean the shaver after every shave.
- Clean the shaving heads frequently with Philips
Shaving Head Cleaning Spray (HQ110) for
optimal shaving performance.
- You can clean the outside of the shaver with
a damp cloth. Do not clean the shaving unit
with a cloth.
Cleaning the shaving unit
Be careful with hot water. Always check if the
water is not too hot, to prevent your hands from
getting burnt.
1 Switch off the shaver, remove adapter from
wall socket and pull the appliance/small plug
out of the shaver.
2 Rinse the shaving unit under a hot tap for
some time (Fig. 11).
Note: You can also clean the shaving unit with the
cleaning brush supplied.
3 After rinsing the appliance under the tap,
hold it upright for 10-15 seconds to allow
water to run out of the bottom.
4 Press the release buttons on the shaving unit
(1) and pull the shaving head holder off the
shaving unit (2). (Fig. 12)
5 Rinse the shaving head holder under a hot
tap for 30 seconds (Fig. 13).
Note: You can also clean the shaving head holder with
the cleaning brush supplied.
6 Carefully shake off excess water and let the
shaving head holder dry.
Never dry the shaving head holder with a towel
or tissue, as this may damage the shaving heads.
7 Reattach the shaving head holder to the
shaving unit (‘click’) (Fig. 14).
Extra-thorough cleaning method
1 Switch off the shaver.
2 Press the release buttons on the shaving unit
(1) and pull the shaving head holder off the
shaving unit (2) (Fig. 15).
3 To unlock the orange retaining ring, turn it in
the direction of the arrows indicated in and
on the retaining ring (Fig. 16).
4 Lift the retaining ring out of the shaving head
holder. (Fig. 17)
5 Remove the cutter and the shaving guard
(Fig. 18).
Note: Do not clean more than one cutter and shaving
guard at a time, since they are all matching sets.
If you accidentally put a cutter in the wrong shaving
guard, it may take several weeks before optimal
shaving performance is restored.
6 Clean the cutter with the cleaning brush
supplied (Fig. 19).
7 Clean the inside of the shaving guard (Fig. 20).
8 After cleaning, place the shaving guard back
into the shaving head holder. Make sure the
two wings t exactly into the recesses of the
shaving head holder (Fig. 21).
9
Place the cutter back into the shaving guard
with the cutter legs pointing downwards
(
Fig. 22).
10 Place the retaining ring back onto the shaving
head holder (1). To reattach the retaining ring,
turn it against the direction of the arrows
indicated in and on the retaining ring (2)
(Fig. 23).
Note: Make sure the retaining ring is xed properly.
The four wings of the retaining ring have to be
located exactly under the recesses of the shaving
head holder (Fig. 24).
11 Reattach the shaving head holder to the
shaving unit (‘click’). (Fig. 14)
Note: If the shaving unit does not close smoothly,
check if you have positioned the shaving heads
properly and if the retaining rings are xed properly.
Problem Possible cause Solution
The
temperature
of the shaver
is too high. In
this case, the
shaver does
not work.
Let the shaver
cool down.
As soon as the
temperature
of the shaver
has dropped
sufciently, you
can switch on the
shaver again.
The shaver
does not
work, even
though it is
connected
to the
mains.
This shaver is
not designed
to be used
directly from
the mains.
Remove the
adapter from the
wall socket and
the small plug
from the shaver.
You can now
switch on the
shaver again.
My skin is
irritated
after
shaving.
Your skin
needs time
to get used
to the Philips
shaving
system.
Skin irritation
during the rst
2-3 weeks of
use is possible.
After this period,
the skin irritation
usually disappears.
The shaving
heads are
damaged or
worn.
Replace the
shaving heads
(see chapter
‘Replacement’).
The
rotation
speed of
the shaving
heads is
lower than
usual.
Too much
dirt has
collected in
the shaving
heads.
Clean the shaving
heads. See chapter
‘Cleaning and
maintenance’.
The
rechargeable
battery is
low.
Recharge the
battery. See
chapter ‘Charging’.
The shaving
heads do
not stay in
place.
You did
not x the
retaining
rings
properly.
The retaining ring
is xed properly if
the four wings of
the retaining ring
are located exactly
under the recesses
of the shaving
head holder.
Cleaning the trimmer (RQ350 only)
Clean the trimmer after every use.
Cleaning the trimmer under the tap
1 Switch on the appliance with the trimmer
attached.
2 Rinse the trimmer under a hot tap for
some time. (Fig. 25)
3 After cleaning, switch off the appliance.
4 After rinsing the appliance under the tap,
hold it upright for 10-15 seconds to allow
water to run out of the bottom.
Cleaning the trimmer with the cleaning
brush supplied
1 Switch off the trimmer.
2 Clean the trimmer with the short-bristled
side of the cleaning brush. Brush up and down
along the trimmer teeth. (Fig. 26)
Tip: For optimal trimmer performance, lubricate the
trimmer teeth frequently with Philips Shaving Head
Cleaning Spray (HQ110).
Storage
Note: Make sure the shaving unit is dry before you
store the shaver.
1 Put the protection cap on the shaver after
use to prevent damage and to avoid dirt
accumulation in the shaving heads (Fig. 27).
Replacement
For maximum shaving performance, we advise
you to replace the shaving heads every two years.
Replace damaged shaving heads right away.
Only replace the shaving heads with original
RQ32 Philips shaving heads. See also chapter
‘Ordering accessories’.
1 Switch off the shaver.
2 Press the release buttons on the shaving unit
and pull the shaving head holder off
the shaving unit (Fig. 12).
3 To unlock the orange retaining ring, turn it in
the direction of the arrows indicated in and
on the retaining ring (Fig. 16).
4 Lift the retaining ring out of the shaving head
holder (Fig. 17).
5 Remove the shaving heads and place new
ones in the shaving head holder.
Make sure the two wings of the shaving heads t
exactly into the recesses.
6 Place the retaining ring back onto the shaving
head holder (1). To reattach the retaining ring,
turn it against the direction of the arrows
indicated in and on the retaining ring (2)
(Fig. 23).
Note: Make sure the retaining ring is xed properly.
The four wings of the retaining ring have to be
located exactly under the recesses of the shaving
head holder (Fig. 24).
7 Reattach the shaving head holder to the
shaving unit (‘click’) (Fig. 14).
Note: If the shaving unit does not close smoothly,
check if you have positioned the shaving heads
properly and if the retaining rings are xed properly.
Ordering accessories
To buy accessories or spare parts, visit
www.shop.philips.com/service or go to
your Philips dealer. You can also contact the Philips
Consumer Care Centre in your country (see the
worldwide guarantee leaet for contact details).
The following accessories are available:
- RQ32 Philips shaving heads
- RQ575 Philips cleansing brush attachment
- HQ110 Philips Shaving Head Cleaning Spray
Recycling
Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an ofcial collection point for recycling. By doing
this, you help to preserve the environment.
Removing the rechargeable shaver
battery
Only remove the rechargeable battery when you
discard the shaver. Make sure the rechargeable
battery is completely empty when you remove it.
Be careful, the battery strips are sharp.
1 Undo the screw in the back panel of the
shaver with a screwdriver (1) and remove the
back panel (2) (Fig. 28).
2 Bend the hooks aside and remove the power
unit (Fig. 29).
3 Break the snap hooks (1) and remove the
front panel of the power unit (2) (Fig. 30).
4 Take out the battery holder (1) and cut the
battery tags with a pair of cutting pliers (2)
(Fig. 31).
5 Remove the rechargeable battery.
Guarantee and support
If you need information or support, please visit
www.philips.com/support or read the separate
worldwide guarantee leaet.
Guarantee restrictions
The shaving heads (cutters and guards) are
not covered by the terms of the international
guarantee because they are subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the appliance
.
If you are unable to solve the problem
with the
information below, visit www.philips.com/
support for a list of frequently asked questions
or contact the Consumer Care Centre in your
country.
Problem Possible cause Solution
The shaver
does not
shave as
well as it
used to.
The shaving
heads are
damaged or
worn.
Replace the
shaving heads
(see chapter
‘Replacement’).
The shaving
heads are
dirty.
Clean the cutters
and guards with
the cleaning brush
supplied (see
chapter ‘Cleaning
and maintenance’,
section ‘Extra-
thorough cleaning
method’).
Long hairs
obstruct
the shaving
heads.
Clean the cutters
and guards with
the cleaning brush
supplied (see
chapter ‘Cleaning
and maintenance’,
section ‘Extra-
thorough cleaning
method’).
The shaver
does not
work when
I press
the on/off
button.
The
rechargeable
battery is
empty.
Recharge the
battery (see
chapter ‘Charging’).
3 按下開關按鈕，開啟鬢角刀電源。這時即
可開始修整。
4 按下開關按鈕，關閉鬢角刀電源。
5 從電鬍刀中垂直抽出鬢角刀。(圖9)
注意：當您從電鬍刀中抽出鬢角刀時，
請勿旋轉。
6 將電鬍刀組的突耳插入電鬍刀頂端的凹槽
(1)，再將電鬍刀組往下壓(2)即可安裝到
電鬍刀上(會聽見「喀噠」一聲)。(圖10)
清潔與維護
拆下電源線的握把零件，再於水中清潔。
切勿使用鋼絲絨、磨蝕性的清潔劑或侵蝕性
的液體(例如汽油或丙酮)清潔電鬍刀及其配
件。
- 每次刮鬍後均需清潔電鬍刀。
- 為得到最佳的刮鬍性能，請經常使用飛利
浦電鬍刀刀頭噴霧清潔劑 (HQ110) 清潔電
鬍刀刀頭。
- 您可以使用濕布清潔電鬍刀外側。請勿用
布清潔電鬍刀組。
清洗電鬍刀組
請小心使用熱水。隨時檢查熱水是否太燙，
以避免手部燙傷。
1關閉電鬍刀電源，將轉換器從電源插座
拔下，並將產品/小插頭自電鬍刀上拔下。
2將電鬍刀組以熱水沖洗一段時間。(圖11)
注意：您也可以用產品所附的清潔刷清潔電
鬍刀組。
3 在水龍頭下沖洗本產品，將其直立
10-15秒，讓水從底部流出。
4 按下電鬍刀組的釋放鈕(1)並將電鬍刀刀
頭固定座從電鬍刀組取下(2)。(圖12)
5 將電鬍刀刀頭固定座放在熱水龍頭下沖洗
30秒。(圖13)
注意：您也可以用產品所附的清潔刷清潔電
鬍刀刀頭固定座。
6 仔細甩乾多餘的水份之後，讓電鬍刀刀頭
固定座乾燥。
切勿使用毛巾或紙巾擦乾電鬍刀刀頭固定座，
因為此舉可能會造成電鬍刀刀頭損害。
7 將電鬍刀刀頭固定座重新接上電鬍刀組
(會聽見「喀噠」一聲)。(圖14)
「充電」指示燈
- 電鬍刀充電時，轉換器的指示燈會亮起。
(圖 4)
「電量不足」指示燈
-
電池即將用盡時，電鬍刀的指示燈會亮
起。
(圖 5)
充電
請勿將電鬍刀置於包裝內充電。
1將小插頭插上電鬍刀。
2將轉換器插入插座。
, 轉換器的指示燈亮起時，表示電鬍刀正在
充電中。
注意：電鬍刀充飽電力後，轉換器指示燈不
會變色，也不會熄滅。
使用本電鬍刀
注意：您無法在電鬍刀仍連接在電源上時使
用。
刮鬍
皮膚適應期
您第一次刮鬍的結果可能不如您所預期，皮膚
甚至可能稍微刺痛。這是正常現象。您的皮膚
與鬍鬚需要時間適應任何新的刮鬍系統。
我們建議您定期刮鬍 (每週至少 3 次) 為期
3 週，讓您的肌膚適應新的電鬍刀。這段期
間，
請只使用您的新電鬍刀，不要使用其他的
刮鬍方式。如果您使用不同的刮鬍方式，您的
皮膚可能較難適應新的刮鬍系統。
1按下開關按鈕，開啟電鬍刀電源。
2將電鬍刀刀頭在皮膚上移動，請同時用直
線及畫圓的方式來移動。(圖6)
3 按下開關按鈕，關閉電鬍刀電源。
4 每次刮鬍後，請清潔本電鬍刀
(請參閱「清潔與維護」單元)。
修剪 (僅限 RQ350)
您可以使用鬢角刀修整鬢角與鬍髭。
1從電鬍刀中垂直抽出電鬍刀組。(圖7)
注意：當您從電鬍刀中抽出電鬍刀組時，
請勿旋轉。
2
將鬢角刀的突耳插入電鬍刀頂端的凹槽(1)，
再將鬢角刀往下壓(2)即可安裝到電鬍刀
上(會聽見「喀噠」一聲)。(圖8)
警告
- 切勿使用超過 80°C 的熱水沖洗電鬍刀。
- 請僅將本產品用於本使用手冊所述之相關
用途。
- 基於衛生的理由，請勿多人共用本產品。
- 切勿在插有或插著電子空氣清新器的電源
插座或附近使用轉接器，以免造成轉接器
無法修復的損害。
- 絕對不可使用壓縮空氣、鋼絲絨、磨蝕性
的清潔劑或侵蝕性的液體 (例如汽油或丙
酮) 清潔本產品。
- 請先取下握把零件的可拆式電源線，再於
水中清洗此零件。
- 在您沖洗時，水可能會從電鬍刀底部的插
孔滴落。此為正常現象，不會造成危險，
因為所有的電子零件都密封於電鬍刀內的
電源裝置中。
電磁場 (EMF)
- 本飛利浦產品符合所有電磁場暴露的相關
適用標準和法規。
一般
- 本電鬍刀採防水設計，可於泡澡或淋浴時
使用，也可直接在水龍頭下沖洗。基於安
全考量，本電鬍刀只能以無線方式操作。
(圖 2)
- 本產品適用於 100 到 240 伏特的插座電壓。
- 轉換器可將 100-240 伏特的電壓轉換為低
於 24 伏特的安全低電壓。
- 最高噪音等級：Lc = 69dB(A)
一般說明 (圖 3)
1 保護蓋
2 附電鬍刀刀頭固定座的電鬍刀組
3 電鬍刀刀頭固定座釋放鈕
4 開關按鈕
5 「電量不足」指示燈
6 固定環
7 刀具
8 電鬍刀刀網
9 電鬍刀刀頭固定座
10 鬢角刀 (僅限 RQ350)
11 轉換器
12 充電指示燈
13 小插頭
14 清潔刷
充電
產品充飽電約需要 10 小時。
充飽電的電鬍刀可刮鬍 30 分鐘。
若您的鬢鬚濃密，電鬍刀的刮鬍時間可能少
於 30 分鐘。此外，取決於您的刮鬍方式、
清潔習慣和鬍鬚類型，可使用時間也可能會隨
著時日改變。
Problem Possible cause Solution
After fully
charging
the shaver,
it provides
less than
30 shaving
minutes.
If you have a
heavy beard,
the shaver
may provide
less than
30 shaving
minutes.
The number
of shaving
minutes may
also vary
over time,
depending
on your
shaving
behaviour,
cleaning
habits and
beard type.
繁體中文
簡介
恭喜您購買本產品並歡迎加入飛利浦！請於
www.philips.com/welcome 註冊您的產品，
以善用飛利浦提供的支援。
重要安全資訊
使用本產品及其配件前，請先仔細閱讀此重要
資訊，並保留說明以供日後參考。不同的產品
可能會隨附不同的配件。
危險
- 請保持轉換器乾燥。 (圖 1)
警示
- 轉換器內含一個變壓器。請勿切斷轉換器
而以其他插頭取代，否則會造成危險。
- 本產品不適合供下列人士 (包括孩童) 使
用：
身體官能或心智能力退化者，或是經
驗與使用知識缺乏者。他們需要有負責其
安全
的人員在旁監督，或指示產品的使用方
法，
方可使用。
- 請勿讓孩童使用本產品或將本產品當成
玩具。
- 在水龍頭下沖洗電鬍刀之前，請先拔掉電
鬍刀的插頭。
- 使用前請務必檢查本產品。如有損壞情
況，
請勿繼續使用，否則可能導致受傷。
零件如有受損，請務必以原型號更換之。
問題 可能原因 解決方法
長鬍鬚卡住
電鬍刀刀
頭。
使用隨附的清潔刷
清潔刀具及刀網
(請參閱「清潔與
維護」單元的「超
徹底清潔方法」小
節)。
我按下
開關按
鈕時，
電鬍刀
沒有反
應。
充電式電池
沒電。
將電池重新充電
(請參閱「充電」
單元)。
電鬍刀過
熱。在此情
況下，電鬍
刀將無法使
用。
讓電鬍刀冷卻。
等到電鬍刀充分降
溫，您就能再度啟
動電鬍刀的電源。
電鬍刀
無法運
作，即
使已經
連接到
電源。
此電鬍刀無
法直接插電
使用。
將轉換器從電源插
座拔除，並將小插
頭從電鬍刀上取
下。現在您可以再
次開啟電鬍刀的電
源。
刮鬍之
後，皮
膚感到
刺痛。
您的皮膚需
要一些時間
才能適應飛
利浦電鬍刀
系統。
開始使用的第 2 到
3 週，皮膚可能會
有過敏現象。過了
這段時間，皮膚過
敏的症狀通常會消
失。
電鬍刀刀頭
毀壞或磨
損。
更換電鬍刀刀頭
(請參閱「更換」
單元)。
電鬍刀
刀頭的
旋轉速
度比平
常緩
慢。
過多污垢累
積在電鬍刀
刀頭中。
請清潔電鬍刀刀
頭。請參閱「清潔
與維護」單元。
充電式電池
電力不足。
為電池充電。請參
閱「充電」單元。
電鬍刀
刀頭不
穩固。
固定環未妥
善固定。
若固定環的四翼已
準確崁入電鬍刀刀
頭固定座的凹處，
則表示固定環已正
確固定。
回收
本產品使用壽命結束時，請勿與一般家庭廢棄
物一併丟棄。請將本產品送至政府指定的回收
站，此舉能為環保盡一份心力。
取出電鬍刀的充電式電池
棄置本電鬍刀前，請先取出充電式電池。
當您要取出充電式電池時，請確認其電力已完
全耗盡。
電池固定帶非常銳利，請小心。
1用螺絲起子(1)轉開電鬍刀的背板螺絲，
拆下背板(2)。(圖28)
2彎折旁邊的扣鉤，然後取出供電裝置。
(圖29)
3 斷開彈簧鉤(1)，並取下供電裝置的正面護
板(2)。(圖30)
4 取出電池固定座(1)並使用剪鉗(2)將電池
拉片剪斷。(圖31)
5 取出充電式電池。
保固與支援
如果您需要資訊或支援，請造訪：
www.philips.com/support，或另行參閱全球
保證書。
保固限制
電鬍刀刀頭 (刀具和刀網) 由於其耗損性，因
此不在全球保固範圍內。
疑難排解
本單元概述您使用本產品時最常遇到的問題。
如果您無法利用以下資訊解決您遇到的問題，
請造訪 www.philips.com/support 查看常見問
題清單，或聯絡您所在國家/地區的飛利浦客
戶服務中心。
問題 可能原因 解決方法
電鬍刀
不像平
常一樣
運作。
電鬍刀刀頭
毀壞或磨
損。
更換電鬍刀刀頭
(請參閱「更換」
單元)。
電鬍刀刀頭
髒污。
使用隨附的清潔刷
清潔刀具及刀網
(請參閱「清潔與
維護」單元的「超
徹底清潔方法」小
節)。
2以清潔刷的短毛側來清潔鬢角刀。請沿著
鬢角刀的刀齒上下地刷。(圖26)
提示：為使鬢角刀發揮最佳性能，請經常使
用飛利浦電鬍刀刀頭噴霧清潔劑(HQ110)
潤滑鬢角刀的刀齒。
收納
注意：務必等電鬍刀組乾燥之後再收納電鬍
刀。
1使用後請為電鬍刀蓋上保護蓋以防損壞，
並避免污垢累積在電鬍刀刀頭中。(圖27)
更換
為得到最佳的刮鬍性能，我們建議您請每兩年
更換一次電鬍刀刀頭。有損傷的電鬍刀刀頭則
請要立即更換。
更換電鬍刀刀頭時，限使用原廠 RQ32 飛利浦
電鬍刀刀頭。亦請參閱「訂購配件」單元。
1請關閉電鬍刀電源。
2按下電鬍刀組的釋放鈕，將電鬍刀刀頭固
定座從電鬍刀組取下。(圖12)
3 若要鬆開橘色固定環，請將它依固定環上
指示的箭頭旋轉。(圖16)
4 從電鬍刀刀頭固定座上取出固定環。
(圖17)
5 取出電鬍刀刀頭，然後在電鬍刀刀頭固定
座換上新的刀頭。
確定電鬍刀刀頭兩翼準確崁入凹處。
6 將固定環放回電鬍刀刀頭固定座(1)。要重
新裝回固定環，將固定環朝箭頭標示的反
方向旋轉(2)。(圖23)
注意：請確定固定環已正確固定。固定環
的四翼必須準確崁入電鬍刀刀頭固定座的凹
處。(圖24)
7 將電鬍刀刀頭固定座重新接上電鬍刀組
(會聽見「喀噠」一聲)。(圖14)
注意：若電鬍刀組無法順利關上，請檢查電
鬍刀刀頭安裝位置是否正確，以及固定環是否
確實固定。
訂購配件
若要購買配件或備用零件，請造訪
www.shop.philips.com/service，或洽詢您的
飛利浦經銷商。您也可以聯絡您所在國家/地
區的飛利浦客戶服務中心 (聯絡詳細資料請參
閱全球保證書)。
備有下列配件可供另外選購：
- RQ32 飛利浦電鬍刀刀頭
- RQ575 飛利浦潔顏刷配件
- HQ110 飛利浦電鬍刀刀頭噴霧清潔劑
超徹底清潔方法
1請關閉電鬍刀電源。
2按下電鬍刀組的釋放鈕(1)並將電鬍刀刀
頭固定座從電鬍刀組取下(2)。(圖15)
3 若要鬆開橘色固定環，請將它依固定環上
指示的箭頭旋轉。(圖16)
4 從電鬍刀刀頭固定座上取出固定環。
(圖17)
5 取下電鬍刀刀網與刀片。(圖18)
注意：因為刀片及刀網是成對的一組，請勿
一次清潔一組以上。如果您不小心將刀片放進
錯誤的電鬍刀刀網中，可能要花幾週的時間才
能恢復最理想的刮鬍效果。
6 使用隨附於電鬍刀的清潔刷來清潔刀片。
(圖19)
7 清潔電鬍刀刀網內部。(圖20)
8清潔完畢後，將電鬍刀刀網裝回電鬍刀刀
頭固定座。請確定兩翼準確崁入電鬍刀刀
頭固定座的凹處。(圖21)
9
請將刀片放回電鬍刀刀網，使刀片腳朝
下。
(圖22)
10將固定環放回電鬍刀刀頭固定座(1)。要重
新裝回固定環，將固定環朝箭頭標示的反
方向旋轉(2)。(圖23)
注意：請確定固定環已正確固定。固定環的四
翼必須準確崁入電鬍刀刀頭固定座的凹處。
(圖24)
11將電鬍刀刀頭固定座重新接上電鬍刀組
(會聽見「喀噠」一聲)。(圖14)
注意：若電鬍刀組無法順利關上，請檢查電
鬍刀刀頭安裝位置是否正確，以及固定環是否
確實固定。
清潔鬢角刀 (僅限 RQ350)
每次使用後均需清潔鬢角刀。
將鬢角刀放在水龍頭下沖洗
1裝上鬢角刀後，開啟產品電源。
2將鬢角刀以熱水沖洗一段時間。(圖25)
3 清潔之後，關閉產品電源。
4 在水龍頭下沖洗本產品，將其直立
10-15秒，讓水從底部流出。
使用隨附的清潔刷來清潔鬢角刀
1關閉鬢角刀電源。
問題 可能原因 解決方法
電鬍刀
充飽電
後，可
提供的
刮鬍時
間少於
30 分
鐘。
若您的鬢鬚
濃密，電鬍
刀的刮鬍時
間可能少於
30 分鐘。此
外，取決於
您的刮鬍方
式、清潔習
慣和鬍鬚類
型，可使用
時間也可能
會隨著時日
改變。
20/07/2015
-
1
-
2
-
3
-
4
-
5
-
6
