SKYDANCE DA4-CM 4 インストールガイド

ブランド: SKYDANCE

モデル: DA4-CM 4

タイプ: インストールガイド

SKYDANCE DA4-CM 4 チャンネル定電流 DALI 調光器は、様々な照明アプリケーションに適した高品質で信頼性の高い調光ソリューションです。DT6 調光または DT8 調光（TC、RGB、RGBW）から選択でき、柔軟な調光オプションを提供します。

この調光器は、12～48VDC の定電圧電源で動作し、最大出力電流はチャンネルあたり 150～500mA または 350～1200mA です。これにより、幅広い LED 照明器具と互換性があります。調光器は、DALI 信号入力を受け入れ、標準の DALI プロトコルに従って動作します。これにより、他の DALI 対応デバイスとシームレスに統合できます。

SKYDANCE DA4-CM 4 は、調光範囲が広く、スムーズな調光が可能です。また、

User Manual Ver 1.0.0

Model No.: DA4-CM(150-500mA) / DA4-CM(350-1200mA)

Features

Page 1

1 Address/4 Channel/DT8/Constant current/PWM dimming /Numeric display

4 Channel Constant Current LED DALI Dimmer

Mechanical Structures and Installations

DA4-CM 4 Channel Constant Current LED DALI Dimmer

Technical Parameters

Output power 4 x (0.45-22.5)W (150-500mA)

4 x (1.05-54)W (350-1200mA)

Output voltage 4 x (3-45)VDC

Output current 4CH,150-500mA or 350-1200mA/CH

Input and Output

Input voltage 12-48VDC

Output type Constant current

Operation temperature

Case temperature (Max.)

Environment

IP20

IP rating

Ta: -30

C ~ +55

T c: +80

Warranty and Protection

5 years

Protection

Reverse Polarity

Over-heat

Short circuit

Warranty

23mm

170mm

50mm

Setting key Digital display

Two groups of DALI signal input

DALI bus no need distinguish

plus-minus polarity

Installation rack

Output LED +

Installation rack

Wiring Diagram

● 4 channel constant current DALI LED Dimmer with digital display, 150-500mA or 350-1200mA per channel.

● 1 DALI address, DT6 dimming or DT8-TC color temperature or DT8-RGB or DT8-RGBW selectable.

● In accordance with DALI standard protocol IEC 62386-102, IEC 62386-207, IEC 62386-209and in compliance

with DALI products from other international incorporation.

● DALI address can be manually assigned and shown in digital display or automatically assigned by DALI master.

● PWM digital dimming, standard DALI logarithmic dimming curve.

● PWM frequency 1000/2000/4000/8000Hz selectable.

● Over-heat / Short circuit protection, recover automatically.

● With fast self-testing function.

Dimming data

Dimming range

DALI

0 -100%

Input signal

Dimming curve Logarithmic

4000Hz (default)

PWM Frequency

Power input -

Power input +

900mA500mA 1050mA 1200mA

700mA

3-45V3-45V 3-45V3-45V 3-45V

2.7-40.5W

1.5-22.5W 3.15-47.25W 3.6-54W

1.8-27W

350mA

3-45V

1.05-15.75W

400mA

3-45V

0.9-13.5W 1.2-18W

250mA

3-45V

0.75-11.25W

200mA

3-45V

0.6-9W

150mA

3-45V

0.45-6.75W

DA4-CM

(150-500mA)

DA4-CM

(350-1200mA)

450mA 500mA

3-45V 3-45V

1.35-20.25W

LED Current Selection

Output Voltage

Output Current

Output Power/CH

Output Voltage

Output Current

Output Power/CH

600mA

3-45V 3-45V

3-45V

1.05-15.75W 1.5-22.5W

300mA 350mA

3-45V

2.4-36W

800mA

2.1-31.5W

DA1 DA2

SIGN AL INPUT

DA1 DA2

DA4-CM(150-500mA) DA4-CM(350-1200mA)

INPUT

12-48VDC

LED OUTPUT

Output Red LED -

Output Green LED -

Output Blue LED -

Output White LED -

● DA4-CM for (C-1) single color

Note: The four output LED channels output is same.

Power Supply

12-48VDC

Constant Voltage

AC100-240V

DALI Master

DA1 DA2

SIGN AL INPU T

DA1 DA2

INPUT

12-48VDC

LED OUTPUT

● DA4-CM for (C-3) RGB

Note: The 4th LED channel no output.

Power Supply

12-48VDC

Constant Voltage

AC100-240V

DALI Master

DA1 DA2

SIGN AL INPU T

DA1 DA2

INPUT

12-48VDC

LED OUTPUT

● DA4-CM for dual color (C-2)

Note: The 3/4 LED channel output is same as 1/2 LED channel.

Power Supply

12-48VDC

Constant Voltage

AC100-240V

DALI Master

DA1 DA2

SIGN AL INPU T

DA1 DA2

INPUT

12-48VDC

LED OUTPUT

AC Power

50/60Hz

AC Power

50/60Hz

AC Power

50/60Hz

Drives 1-13pcs LED per channel x 3CH

Drives 1-13pcs LED per channel x 4CH

User Manual Ver 1.0.0

● The rst time you use it, you need to set the light type according to your application needs.

● Press the M button for 2 seconds to set the light type.

● Press the ◀or ▶ key to switch between the single color ("C-1"), dual color ("C-2"), RGB ("C-3") or RGBW ("C-4") light type.

● Short press the M button or timeout for 10 seconds to exit the light type setting.

Operation

Setting the light type

DALI address assigned by DALI masters

DALI address can also be assigned by DALI Master controller automatically.

Please refer to user manuals of compatible DALI Masters for specic operations.

The digital display will show “AAU” When the DALI master is assigning address.

After address is assigned, the digital display will show the start DALI address”Axx”, xx is from 00 to 63.

Using DALI master assign address may result in discontinuous address, the digital display will show the start DALI address”Uxx”.

When setting C-1 type, DT6 dimming, 4-channel output is the same.

When setting C-2 type, DT8-TC, 3/4 LED channel and 1/2 LED channel output is the same.

When setting C-3 type, DT8-RGB, the 4th channel does not output.

When setting C-4 type, DT8-RGBW, 4 channels are output independently.

Set DALI Address via buttons

● Long press ◀ or ▶ key for 2s, prepare for set the start DALI address, then press ◀ or ▶ key to set the start DALI address.

● Short press M key or timeout 10s, quit start DALI address setting.

● The start DALI address can be manually assigned from 00-63-FF.

● by factory defaults, no DALI address is assigned for the dimmer, and digital display shows “AFF”.

Set PWM frequency

● Long press M & ◀ key for 2s, prepare for set PWM frequency.

● Short press ◀ or ▶ key to switch between 1000Hz("F10"), 2000Hz("F20"), 4000Hz("F40") or 8000Hz("F80").

Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera

(No flickers for video).

● Short press M key or timeout 10s, quit PWM frequency setting.

Output current setting

● Please select the correct current rstly when the LED load is disconnected.

● Long press M and ◀and◀ key in the same time for 2s, prepare for setup output current.

● For DA4-C(150-500mA): short press ◀ or ▶ key to switch 150mA("C15"), 200mA("C20"), 250mA("C25"),

300mA ("C30"), 350mA("C35"), 400mA("C40") , 450mA("C45") or 500mA("C50").

● For DA4-C(350-1200mA): short press ◀ or ▶ key to switch 350mA("C35"), 500mA("C50"), 600mA("C60"),

700mA("C70"),800mA("C80"), 900mA("C90") , 1050mA("CA5") or 1200mA("CC0").

● Press M key or timeout 10s, quit output current setting.

Light type setting instructions:

Power Supply

12-48VDC

Constant Voltage

AC100-240V

DA1 DA2

SIGN AL INPU T

DA1 DA2

● DA4-CM for RGBW (C-4)

DALI Master

INPUT

12-48VDC

LED OUTPUT

● Long press ◀ and ▶ key for 2s, restore factory default parameter, display ”RES”.

● Factory default parameter: no DALI address is assigned, DT8-RGBW, PWM frequency is 4000Hz.

● Long press M & ▶ key for 2s, enter fast self-testing, the output channel will be on orderly then all on.

Restore factory default parameter

• DO NOT install with power applied to device.

• DO NOT expose the device to moisture.

Safety & Warnings

Page 2

DA4-CM 4 Channel Constant Current LED DALI Dimmer

AC Power

50/60Hz

Drives 1-13pcs LED per channel x 4CH

技术参数

机械结构和安装

输⼊和输出

5年

质保和保护

质保

175x54 x27mm(⻓x宽x⾼)

0.131kg

输⼊电压

输出电压

输出电流

输出功率

输出类型

DALI

0 -100%

对数

4000Hz (默认)

调光数据

输⼊信号

调光范围

调光曲线

PWM频率

包装

尺⼨

总重量

环境

⼯作温度

外壳最⾼温度

特点

Ta: -30

C ~ +55

Ta: +80

版本2.0.0

景晴光电

DALI4路恒流LED调光器

型号:DA4-CM(150-500mA) / DA4-CM(350-1200mA)

1个DALI地址/4通道恒流/DT8/PWM调光/数字显⽰

DA4-CM(150-500mA) DA4-CM(350-1200mA)

● 4通道恒流LEDDALI调光器，带数字显⽰，每通道输出电流150-500mA或350-1200mA。

● 1个DALI地址,DT6调光/DT8-TC⾊温/DT8-RGB/DT8-RGBW可选。

● 符合DALI标准协议IEC62386-102、IEC62386-207、IEC62386-209，

兼容其他品牌的DALI产品。

● DALI地址可以⼿动分配并数字显⽰，也可以由DALI主机⾃动分配。

● PWM数字调光，标准DALI对数调光曲线。

● PWM频率1000/2000/4000/8000Hz可选。

● 过热/短路保护，⾃动恢复。

● 具有快速⾃检功能。

23mm

170mm

50mm

900mA500mA 1050mA 1200mA

700mA

3-45V3-45V 3-45V3-45V 3-45V

2.7-40.5W

1.5-22.5W 3.15-47.25W 3.6-54W

1.8-27W

350mA

3-45V

1.05-15.75W

400mA

3-45V

0.9-13.5W 1.2-18W

250mA

3-45V

0.75-11.25W

200mA

3-45V

0.6-9W

150mA

3-45V

0.45-6.75W

DA4-CM

(150-500mA)

DA4-CM

(350-1200mA)

450mA 500mA

3-45V 3-45V

1.35-20.25W

输出电压

输出电流

输出功率/CH

600mA

3-45V 3-45V

3-45V

1.05-15.75W 1.5-22.5W

300mA 350mA

3-45V

2.4-36W

800mA

2.1-31.5W

设置键数字显视屏

安装孔

DA1 DA2

SIGN AL INPUT

DA1 DA2

INPUT

12-48VDC

LED OUTPUT

安装孔

输出电压

输出电流

输出功率/CH

LED输出电流选择

两组DALI信号输⼊，

⽆需区分正负极性

LED⽩光输出-

LED蓝光输出-

LED绿光输出-

LED红光输出-

LED输出+

电源输⼊+

电源输⼊-

恒流

4 x (3-45)VDC

12-48VDC

4 x (0.45-22.5)W (150-500mA)

4 x (1.05-54)W (350-1200mA)

4CH, 150-500mA or 350-1200mA/CH

IP20

IP等级

保护

防反接,

过热,

短路

接线图

● DA4-CM⽤于单⾊(C-1)

注意：四个LED通道输出相同。

12-48VDC

恒压电源

AC100-240V

DALI

主控

DA1 DA2

SIGN AL INPU T

DA1 DA2

INPUT

12-48VDC

LED OUTPUT

AC 电源

50/60Hz

驱动1-13个LEDx4个通道

● DA4-CM (C-3) ⽤于 RGB

DA1 DA2

SIGN AL INPU T

DA1 DA2

INPUT

12-48VDC

LED OUTPUT

注意：3/4LED通道输出与1/2LED通道相同。

DA1 DA2

SIGN AL INPU T

DA1 DA2

INPUT

12-48VDC

LED OUTPUT

驱动1-13个LEDx4个通道

AC100-240V

DA1 DA2

SIGN AL INPU T

DA1 DA2

● DA4-CM ⽤于 RGBW (C-4)

INPUT

12-48VDC

LED OUTPUT

AC100-240V

● DA4-CM⽤于双⾊(C-2)

DALI

主控

12-48VDC

恒压电源

AC 电源

50/60Hz

DALI

主控

12-48VDC

恒压电源

AC 电源

50/60Hz

DALI

主控

12-48VDC

恒压电源

AC 电源

50/60Hz

驱动1-13个LEDx3个通道

驱动1-13个LEDx4个通道

注意：第四通道⽆输出。

版本2.0.0

操作

输出电流设置

● 连接LED负载之前，请先设置正确的电流输出。

● 同时⻓按M，◀和▶键2秒，准备设置输出电流。

● 对于DA4-CM(150-500mA)：短按◀或▶ 键切换150mA（“C15”),200mA（“C20”),250mA（“C25”),300mA（“C30”),350mA（“C35”),400mA（“C40”),

450mA（“C45”)或500mA（“C50”)。

● 对于DA4-CM(350-1200mA):短按◀或▶ 键切换350mA（“C35”),500mA（“C50”),600mA（“C60”),700mA（“C70”),800mA（“C80”),900mA（“C90”),

1050mA（“CA5”)或1200mA（“CC0”)。

● ⻓按M键2秒,或超时10秒，退出系统参数设置。

设置灯光类型

● 第⼀次使⽤时，请根据应⽤设置灯光类型。

● ⻓按M键2秒，准备设置灯光类型。

● 按◀或▶键切换单⾊（“C-1”）、双⾊（“C-2”）、RGB（“C-3”）或RGBW（“ C-4”）灯光类型。

● 短按M键或超时10秒，退出灯光型设置。

灯光类型设置说明：

设置C-1，DT6调光类型时，4路输出相同。

设置C-2，DT8-TC类型时，3/4LED通道和1/2LED通道输出相同。

设置C-3，DT8-RGB类型时，第4通道不输出。

设置C-4，DT8-RGBW类型时，4个通道独⽴输出。

按键设置DALI地址

● ⻓按◀或▶键2秒，准备设置DALI地址，然后按◀或▶键设置DALI地址。

● 短按M键或超时10秒，退出DALI地址设置。

● DALI地址可设置为00-63-FF。

● 出⼚默认情况下，调光器未分配DALI地址，数字显⽰“AFF”。

DALI主控设置DALI地址

DALI地址也可以由DALI主控⾃动分配，请参考DALI主控⽤⼾⼿册。

当DALI主控分配地址时，数字显⽰“AAU”。

地址分配完毕，数字显⽰DALI地址“Axx”，xx值从00到63。

设置PWM频率

● 同时⻓按M和◀键2秒,准备设置PWM频率。

● 短按◀或▶键切换1000Hz("F10"),2000Hz("F20"),4000Hz("F40")或者8000Hz("F80")。

较⾼的PWM频率，会导致较低的输出电流，较⾼的电源噪声，但更适合于视频拍摄（⽆闪烁）。

● 短按M键或超时10秒，退出系统参数设置。

安全和警告

● 不要带电安装调光器。

● 不要将调光器安装在潮湿环境。

⼴州景晴光电科技有限公司GuangzhouSkyacneCo.,Ltdwww.iskydance.cn

本资料上的内容均经过认真核对，如有任何印刷错漏或内容上的误解，本公司保留最终解释权。

产品若有技术改进，会编⼊新版说明书中，恕不另⾏通知。

版本2.0.0

SKYDANCE DA4-CM 4 インストールガイド

ブランド: SKYDANCE

モデル: DA4-CM 4

タイプ: インストールガイド

SKYDANCE DA4-CM 4 は、調光範囲が広く、スムーズな調光が可能です。また、

PDFをダウンロードします

報告

他の言語で

English: SKYDANCE DA4-CM 4 Installation guide

SKYDANCE DA4-CM 4 インストールガイド

SKYDANCE DA4-CM 4 インストールガイド

他の言語で

関連論文

その他のドキュメント