Lexmark Infoprint 1116 ユーザーマニュアル

Infoprint 1116

Setup Guide

S510-2307-00



Infoprint 1116

Setup Guide

S510-2307-00



English

Edition: August 2001

Lexmark, MarkVision, and MarkNet are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.

Macintosh is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

This software and documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions

as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 and in applicable FAR

provisions: Lexmark International, Inc., Lexington, KY 40550.

FCC emissions information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

Refer to the Publications CD for details.

Safety information

•If your product is NOT marked with this symbol , it MUST be connected to an electrical outlet that is properly grounded.

•The power cord must be connected to an electrical outlet that is near the product and easily accessible.

•Refer service or repairs, other than those described in the operating instructions, to a professional service person.

•This product is designed, tested, and approved to meet strict global safety standards with the use of specific Lexmark components. The safety

features of some parts may not always be obvious. Lexmark is not responsible for the use of other replacement parts.

•Your product uses a laser, exercise CAUTION: Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

•Your product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand

the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.

Conventions

Warning! A warning identifies something that might damage your printer hardware or software.

CAUTION! A caution identifies something that might cause you harm.

iii

Table of contents

Table of

contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

About your printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v

About this book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Other sources of information . . . . . . . . . . . . . . . . . . . . . . . . viii

Viewing the Publications CD . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Step 1: Unpack the printer . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Attaching an operator panel overlay . . . . . . . . . . . . . . . . . . . . .2

Removing print cartridge packaging . . . . . . . . . . . . . . . . . . . . .2

Step 2: Install the print cartridge . . . . . . . . . . . . . . . . . . . . . 4

Step 3: Install memory cards . . . . . . . . . . . . . . . . . . . . . . . . 6

Removing the printer side cover . . . . . . . . . . . . . . . . . . . . . . . .6

Removing the system board shield . . . . . . . . . . . . . . . . . . . . . .8

Installing a printer memory card . . . . . . . . . . . . . . . . . . . . . . . .9

Installing a flash memory card . . . . . . . . . . . . . . . . . . . . . . . .11

Reattaching the metal shield . . . . . . . . . . . . . . . . . . . . . . . . .13

Reattaching the side cover . . . . . . . . . . . . . . . . . . . . . . . . . . .14

iv Table of contents

Step 4: Install the tray 2 option . . . . . . . . . . . . . . . . . . . . . 15

Step 5: Attach cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Local printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Network printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Attaching a power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Step 6: Load paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Loading tray 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Loading the manual feed . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Loading the optional tray 2 . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Step 7: Verify printer setup . . . . . . . . . . . . . . . . . . . . . . . . 30

Step 8: Understanding the operator panel lights . . . . . . . 31

Step 9: Install printer drivers . . . . . . . . . . . . . . . . . . . . . . . 38

Local printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Network printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

v

Preface

About your printer Three printer models are available: an

entry model, a standard model and a

network model. The differences between

these three models are listed in the

following table.

Item Entry model Standard model Network model

Base memory 2MB 8MB 16MB

Maximum memory 66MB 72MB 80MB

Emulations PCL 5e and

Macintosh

compatibility

PostScript Level 2 and

PCL 6 PostScript Level 2 and

PCL 6

Connectivity Parallel and USB Parallel and USB 10/100 Base-TX

Ethernet and USB

Ships with print

cartridge yield (at

approximately 5%

coverage)

1,500 pages

(standard) 3,000 pages

(standard) 3,000 pages (standard)

vi Preface

Tray 1

Paper support

Paper

support

Top

output

bin

Operator

panel

lights

Paper

guide

Manual

feed

Front output door

Optional tray 2

Use this feature: When you want to:

Tray 1 Load up to 150 sheets of paper or 10 sheets of other media.

Paper support Support media in tray 1 or the top output bin.

Manual feed Load a single sheet of paper/other media. Use for transparencies, labels, envelopes,

and card stock.

Paper guides Adjust the width of the media in tray 1 and the manual feed.

Operator panel lights Check the status of your printer.

Top output bin Stack printed documents face down.

Front output door Print on special media, for example, labels or card stock.

Optional tray 2 Increase your paper capacity.

vii

Preface

Entry and standard model Network model

Parallel cable

connector

USB cable

connector

Power cord connector

Power

switch

Power cord

connector

Power

switch

Ethernet

connector

Use this feature: When you want to:

Parallel cable connector Connect the computer to the entry or standard model printer’s parallel port with a

parallel cable.

USB connector Connect the computer to the network printer’s USB port with a Universal Serial Bus

(USB) cable.

Ethernet cable connector Connect the computer to the network printer’s port with an Ethernet cable.

Power cord connector Connect the printer to a properly grounded wall outlet with a power cord.

Power switch Turn the printer on or off.

viii Preface

Operator panel The operator panel has 6 lights and 1

button. Different light sequences provide

status, attendance and service

information.

Depending on the light sequence, briefly

(approximately 1 second) push the

operator panel button to restart the

printer, display an error code, or activate

other printer functions.

Use your printer driver to change the

paper source, paper size and other

printer settings.

About this book

Note: See the safety information on the

inside of the front cover before setting up

your printer.

This Setup Guide provides detailed

instructions for unpacking and setting up

the printer, installing supplies and

options, loading media, launching the

drivers CD to install printer drivers and

utilities, and printing information from the

Publications CD.

Other sources of

information

Publications CD The Publications CD, which is packaged

with the Setup Guide, provides

information about choosing media,

understanding the operator panel lights,

clearing paper jams, and solving printing

problems.

ix

Preface

Viewing the

Publications CD Insert the Publications CD into your CD-

ROM drive. If the CD does not

automatically launch:

1Select your CD-ROM drive.

2Double-click START.PDF (or

double-click the CD icon on your

desktop and then click

START.PDF if you are using a

Macintosh computer).

You must have a copy of Adobe

Acrobat Reader, Version 4.05c

with Search or later installed on

your computer to view the

Publications CD.

If Acrobat Reader is not installed

on your operating system, visit the

Adobe Web site at

www.adobe.com to download the

Acrobat Reader version you need.

Quick Reference card The Quick Reference card provides easy

access to information about loading

paper, clearing jams, and understanding

common operator panel light messages.

Drivers CD The drivers CD contains all the

necessary printer drivers to get your

printer up and running.

Depending on which version of the

drivers CD shipped with your printer, it

may also contain MarkVision

Professional, other printer utilities,

screen fonts, and additional

documentation.

xPreface

1

Unpack the printer

Step 1: Unpack the printer

1Remove the printer and all

accessories from the packaging

carton.

Save the carton and packing

materials in case you need to

repack the printer for service or

storage.

2Remove all tape from outside and

inside the printer.

3Make sure you have the following

items:

— Printer with print cartridge

installed

—Setup Guide

—Publications CD

—Quick Reference card

—Power cord

—Drivers CD

— Operator panel overlay

If you need help during setup, or if

any items are missing or

damaged, refer to your point of

purchase.

Power cord

Setup Guide and

Publications CD

Quick Reference card

Drivers CD

Overlay

2Unpack the printer

4Place the printer on a flat, stable

surface in a well-ventilated area

near your computer.

Do not place the printer:

— In direct sunlight

— Near heat sources or air

conditioners

— In dusty or dirty environments

Attaching an operator

panel overlay If you have a non-English operator panel

overlay in your printer box and wish to

use it, peel it off, align it on the operator

panel, and press it into place.

Removing print

cartridge packaging

1Use the finger tab to pull down the

printer cover.

3

Unpack the printer

2Grasp the cartridge handle and

pull the print cartridge straight up.

3Remove the protective foam

packaging from the print cartridge.

4Pull off the plastic piece attached

to the ends of the print cartridge.

Discard the plastic piece, foam

and paper.

5Continue with “Install the print

cartridge” on page 4.

Cartridge

handle

4Install the print cartridge

Step 2: Install the print cartridge

1Shake the cartridge to distribute

the toner evenly.

2Insert the print cartridge:

aAlign the colored labels on

either side of the print

cartridge with the

corresponding labels in the

printer.

bHolding the handle, tilt the print

cartridge down and guide it

between the print cartridge

grooves.

cPush down on the cartridge

until it is firmly in place.

5

Install the print cartridge

3Close the printer cover.

What do I do next?

Task Go to page ...

Install optional memory 6

Install tray 2 15

Attach cables 17

6Install memory cards

Step 3: Install memory cards

Depending on your printer model, you

can increase printer memory for a total

of up to 66MB (entry model), 72MB

(standard model), and 80MB (network

model).

If you have a standard or network model,

you can also install a 1MB, 2MB, or 4MB

optional flash memory card for storing

downloaded fonts or macros.

Removing the printer

side cover Before installing any memory options,

you must remove the printer side cover.

ページを読み込んでいます...

Lexmark Infoprint 1116 ユーザーマニュアル

Lexmark Infoprint 1116 ユーザーマニュアル

他の言語で

その他の書類