1
2
34
567
3
9
BCD702A
2
ENGLISH
(Original instructions)
2
3
6
8
8a
6
6
7
4
B C
D E
A1
6
8
8a
A2
2
ENGLISH
(Original instructions)
3
ENGLISH
(Original instructions)
3
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER BCD702A - Drill, has been designed for
screwdriving applications and for drilling in wood, metal and
plastics. This tool is intended for consumer use only.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions listed below may result in
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools.
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
2 2
F
h. Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe
injury within a fraction of a second.
4
ENGLISH
(Original instructions)
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
4
ENGLISH
(Original instructions)
h. Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
Additional power tool safety warnings
Drill safety warnings
1. Safety instructions for all operations
a. Wear ear protectors when impact drilling. Exposure
to noise can cause hearing loss.
b. Use the auxiliary handle(s). Loss of control can cause
personal injury.
c. Brace the tool properly before use. This tool produces
a high output torque and without properly bracing the tool
during operation, loss of control may occur resulting in
personal injury.
d.
Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory or
fasteners may contact hidden wiring.
Cutting accessory
contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an electric
shock.
2.
Safety instructions when using long drill bits
a.
Never operate at higher speed than the maximum speed
rating of the drill bit.
At higher speeds, the bit is likely to
bend if allowed to rotate freely without contacting the
workpiece, resulting in personal injury.
b.
Always start drilling at low speed and with the bit tip in
contact with the workpiece.
At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
the workpiece, resulting in personal injury.
c.
Apply pressure only in direct line with the bit and do not
apply excessive pressure.
Bits can bend causing breakage
or loss of control, resulting in personal injury.
5. Battery tool use and care
a.
manufacturer. A charger that is suitable for one type
another battery pack.
b.
battery packs. Use of any other battery packs may create
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
e. Do not use a battery pack or tool that is damaged or
of injury.
f. -
sive temperature.
130 °C may cause explosion.
g. Follow all charging instructions and do not charge
the battery pack or tool outside the temperature range
Charging improperly or at
6. Service
a.
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
b. Never service damaged battery packs. Service of
battery packs should only be performed by the
manufacturer or authorized service providers.
5
ENGLISH
(Original instructions)
Safety of others
u This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the tool by a person responsible for their safety.
u Children should be supervised to ensure that they do not
play with the appliance.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
5
ENGLISH
(Original instructions)
u Injuries caused when changing any parts, blades or ac-
cessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Labels on tool
The following symbols are shown on the tool along with the
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries and
chargers (Not provided with the tool)
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
Chargers
u Use your BLACK+DECKER charger only to charge the
battery supplied with the tool. Other batteries could burst,
causing personal injury and damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the
charger unit with a regular mains plug.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Torque adjustment collar
4. Keyless chuck
5. LED work light
6. Battery
7. Battery release button
Assembly
Use
Warning! Let the tool work at its own pace. Do not overload.
-
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C.
u Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u
location of wiring and pipes.
u Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
6
ENGLISH
(Original instructions)
Recommended charging temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
u Plug the charger (8) into any standard 230 Volts 50 Hz
electrical outlet.
u Slide the battery pack (6) into the charger as shown in
battery is being charged.
The completion of charge is indicated by the
LED (8a) remaining on continuously. The
pack is fully charged and may be used at this
time or left on the charger.
Warning!
remove the battery from the charger.
Charger diagnostics
This charger is designed to detect certain problems that can
arise with the battery packs or the power source. Problems
Bad battery
The charger can detect a weak or damaged
-
cated on the label. If you see this bad battery
blink pattern, do not continue to charge the battery. Return it
to a service center or a collection site for ecycling.
Hot/cold pack delay
When the charger detects a battery that
is excessively hot or excessively cold, it
automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery has normalized. After
this happens, the charger automatically switches to the Pack
Charging mode. This feature ensures maximum battery life.
Leaving the battery in the charger
The charger and battery pack can be left connected with
battery pack fresh and fully charged. This charger features
an automatic tune-up mode which equals or balances the
individual cells in the battery pack to allow it to function at
peak capacity. Battery packs should be tuned up weekly or
whenever the battery no longer delivers the same amount
of work. To use the automatic tune-up mode, place the
battery pack in the charger and leave it for at least 8 hours.
Important charging notes
u Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 18 ° – 24 °C. DO NOT charge the battery pack in
an air temperature below +4.5 °C), or above +40 °C. This
is important and will prevent serious damage to the battery
pack.
u The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
u If the battery pack does not charge properly:
u Check operation of receptacle by plugging in a lamp
or other appliance;
u Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
u Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 18 ° – 24 °C;
u If charging problems persist, take the tool, battery
pack and charger to your local service center.
u The battery pack should be recharged when it fails to
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse effect on the battery pack.
u Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Unplug the
charger before attempting to clean.
u Do not freeze or immerse the charger in water or any
other liquid.
Installing and removing the battery pack from the
Warning! Make certain the lock-off button (2) is engaged to
prevent switch actuation before removing or installing battery.
To install battery pack:
u Insert battery pack (6) into tool, until an audible click is
u
and pull battery pack (6) out of tool.
6
ENGLISH
(Original instructions)
7
ENGLISH
(Original instructions)
7
ENGLISH
(Original instructions)
Operating Instructions
the operating mode and to set the torque for tightening
screws. Large screws and hard workpiece materials require
a higher torque setting than small screws and soft workpiece
materials.
u For drilling in wood, metal and plastics, set the collar to
the drilling position symbol
u For screwdriving, set the collar to the desired setting. If you
do not yet know the appropriate setting, proceed as
follows:
u Set the collar to the lowest torque setting.
u
u If the clutch ratchets before the desired result is achieved,
increase the collar setting and continue tightening the
screw. Repeat until you reach the correct setting. Use this
setting for the remaining screws.
Warning! Make certain the lock-off button (2) is engaged to
prevent switch actuation before installing or removing acces-
sories.
To insert a drill bit or other accessory:
u Grasp the rear half of the chuck with one hand and use
your other hand to rotate the front half in the counterclock-
wise direction, as viewed from the chuck end.
u Insert the bit or other accessory fully into the chuck, and
tighten securely by holding the rear half of the chuck and
rotating the front portion in the clockwise direction as
viewed from the chuck end.
Warning! Do not attempt to tighten drill bits (or any other ac-
cessory) by gripping the front part of the chuck and turning the
tool on. Damage to the chuck and personal injury may occur
when changing accessories.
For drilling and tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse slider
(2) to the left.
u To select reverse rotation, push the forward/reverse slider
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Drilling/screwdriving
u Select forward or reverse rotation using the forward/re-
verse slider (2).
u To switch the tool on, press the switch (1). The tool speed
depends on how far you press the switch.
u To switch the tool off, release the switch.
Hints for optimum use
Drilling
u Use sharp drill bits only.
u Support and secure work properly, as instructed in the
Safety Instructions.
u Use appropriate and required safety equipment, as
instructed in the Safety Instructions.
u Secure and maintain work area, as instructed in the
Safety Instructions.
u Run the drill very slowly, using light pressure, until
the hole is started enough to keep the drill bit from slipping
out of it.
u Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
u
action.
u DO NOT CLICK THE TRIGGER OF A STALLED DRILL
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
u Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
u Keep the motor running while pulling the bit out of a drilled
hole. This will help reduce jamming.
u Make sure switch turns drill on and off.
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulfurized cutting oil or lard oil.
Screwdriving
u Always use the correct type and size of screwdriver bit.
u
amount of washing liquid or soap as a lubricant.
u Always hold the tool and screwdriver bit in a straight line
with the screw
8
ENGLISH
(Original instructions)
Troubleshooting
Problem Possible cause Possible solution
Unit will not start. Battery pack not
charged.
Check battery pack charg-
ing requirements
Battery pack will not
charge.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Unit shuts off
abruptly.
Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Allow battery pack to cool
down.
Place on charger
and allow to charge.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
u Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior.
Protecting the environment
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries accord-
ing to local provisions. Further information is available at
www.2helpU.com
Technical data
BCD702A
Voltage V
DC
20
No-load speed Min
-1
0 - 600
Max. torque Nm 37
Chuck capacity mm
1-10
Max Drilling capacity
Steel/wood mm 10/25
Weight kg
0.8 (with battery 1.2)
Charger
Input voltage V
AC
220
Output voltage V
DC
20
Current mA 400
Approx. charge time Hours
3 - 4
Battery
Voltage V
AC
Capacity Ah
Type
20
1.5
Li-Ion
BL1518**
Service Information
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the BLACK+DECKER location
nearest to you.
Note
u BLACK+DECKER's policy is one of continuous improve-
ment to our products and, as such, we reserve the right to
u Standard equipment and accessories may vary by country.
u
u Complete product range may not be available in all
countries. Contact your local BLACK+DECKER dealers for
range availability.
3
ENGLISH
(Original instructions)
9
1.
a.
b.
c.
2.
a.
b.
c.
d.
e.
f.
3.
a.
b.
c.
d.
e.
f.
g.
2 2
F
h.
4.
a.
b.
BLACK+DECKER BCD702A
RCD RCD
130°C
10
c.
d.
e.
f.
g.
h.
d.
1.
a.
b.
c.
d.
2.
a.
b.
c.
5.
a.
b.
c.
e.
f.
6.
a.
b.
RCD RCD
130°C
u
u
u
u
u
u
u
u
u
u
u
u
11
u
u
u
u
u
u
u
u
u
u
u
40°C
10ºC40ºC
u
BLACK+ECKER
u
u
8 23050Hz
6 A1A2
LED8a
LED 8a
BLACK+DECKER
1.
2.
3.
4.
5. LED
6.
7.
A1 A2
10°C40°C
24°C
10°C40°C
12
u
u
u
18° 24°C
+4.5°C+40°C
u
u
u
u
6 B
u
u
u
u
u
u
LED
B
2
D
3
u
C 7
6
C
LED
8
LED
LED
18°-24°C
u
u
u
13
-
u
u
u
u
u
40°F
(45ºC)105°F
(+40.5ºC)
u
u
E
2
u
u
2
2
F
BLACK+DECKER
u
u
u
2
1
u
u
u
u
u
u
u
u
u
14
BCD702A
20
Max
0 - 600
37
1-10
10/25
0.8 (1.2)
220
20
Max
400
3 - 4
20
Max
1.5
BL1518**
BLACK+DECKER
BLACK+DECKER
BLACK+DECKER
u
u
u
u
u
u
u
BLACK+DECKER
BLACK+DECKER
www.2helpU.com
N855987
04/2020
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
他の言語で
- English: BLACK+DECKER BCD702A User manual
関連論文
-
BLACK+DECKER EVO181-TW ユーザーマニュアル
-
-
-
-
BLACK+DECKER BDCHD12S1 ユーザーマニュアル
-
-
BLACK+DECKER KTC12 ユーザーマニュアル
-
BLACK+DECKER BEH200 ユーザーマニュアル
-
-
