MDH11KI Quick Reference Guide/ 快速测试参考指南
No. Code Descripon
1 FP_AUDIO Front audio header
2 SPKR Speaker cable connector
3 MIC_IN Audio Mic In port
4 LINE_OUT Audio Line Out port
5 USB3_2 USB 3.0 ports
6 USB3_1 USB 3.0 ports
7 TPM_LPC TPM connector
8 HDMI HDMI 2.0 port
9 DP Display port connector
10 LAN GbE LAN port
11 BATTERY Baery cable connector
12 CLR_CMOS Clear CMOS jumper
13 DC_IN DC In power connector
14 ATX_19V 2 pin power connector
15 FUSB2_5 USB 2.0 header
16 SATAIII_1 SATA 6Gb/s connector
17 SATAIII_0 SATA 6Gb/s connector
18 SATA_PWR Hard disk power connector
19 CPU_FAN CPU fan connector
20 SYS_PANEL Front panel header
21 MON_SW Monitor power switch header
22 SYS_FAN System fan connector
23 SODIMM2 DDR4 SO-DIMM slot#2
24 SODIMM1 DDR4 SO-DIMM slot#1
25 FPD_PWR LVDS power select jumper (12V/19V)
26 LVDS LVDS connector
27 FPD Flat Panel Display connector
28 BL_SW Back light brightness switch
29 LCD_VCC LVDS Drive voltage jumper
30 FUSB2_3 USB 2.0 header
31 CPU Intel LGA1151 socket
32 FUSB2_2 USB 2.0 header
33 FUSB2_4 USB 2.0 header
34 M2_E M.2 slot (PCIe Gen2 x1, Support NGFF-2230, E-Key)
35 COM1 Serial port header
36 M2_M M.2 slot (PCIe Gen2 x4 or SATA 6Gb/s
Support NGFF-2260/2280, M-Key)
37 DMIC_CON Digital Mic connector
3421 5 87 10 11
14
1312
15
16
17
22
19
20
21
2324
25
2829 26
27
303233
35
34
36
37
18
96
31
Front Panel Header/
No. Pin Define
1 HDD LED+
2 Power LED+
3 HDD LED-
4 Power LED-
5 GND
6 Power Buon+
7 Reset Buon
8 Power Buon-
9 No Connect
10 No Pin
1
109
2
Power Connector/
2
1No. Pin Define
1 GND
2 19V
Installing CPU/ 安装 CPU
USB 2.0 Header
No. Pin Define
1 Power (5V)
2 Power (5V)
3 USB DX-
4 USB DY-
5 USB DX+
10
9
2
1No. Pin Define
1 VCC
2 USB-
3 USB+
4 GND
5 No Pin
15
5
1
No. Pin Define
6 USB DY+
7 GND
8 GND
9 No Pin
10 No Connect
1 9
102
Serial Port Cable Connector
No. Pin Define
1 NDCD-
2 NDSR-
3 NRXD-
4 NRTS-
5 NTXD-
No. Pin Define
6 NCTS-
7 NDTR-
8 5V
9 GND
10 No Connect
Memory Populaon Configuraon/ 安装内存
1
2
Rear I/O Connector/ 后面板接口
Off
State Description
Amber On 1Gbps data rate
Green On 100Mbps data rate
10Mbps data rate
10/100/1000 LAN LED:
Speed LED Link/Acvity
LED
No. Desripon
1 DC In power connector
2 GbE Eternet LAN port
3 Display port connector
4 HDMI 1.4 port
No. Desripon
5 USB 3.0 ports
6 Line Out port (Green)
7 Mic In port (Pink)
The HDMI connector is HDCP compliant and supports Dolby True HD and DTS HD
Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM audio
output. You can use this port to connect your HDMI-supported monitor. The
maximum supported resoluon is 4096x2160@24Hz or 2560x1600@60Hz, but the
actual resoluons supported are dependent on the monitor being used.
SATA Connector/SATA 接口
1
7No. Pin Define
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
Hard disk power connectornnector
No. Pin Define
1 VCC3
2 VCC3
3 VCC3
4 GND
5 GND
6 GND
7 VCC
8 VCC
9 VCC
10 GND
1
N2 No. Pin Define
11 GND
12 GND
13 +12V
14 +12V
15 +12V
P1 GND
P2 GND
N1 GND
N2 GND
LVDS
No. Pin Define
1 +RXO3_C
2 -RXO3_C
3 +RXO2_C
4 -RXO2_C
5 +RXO1_C
6 -RXO1_C
7 +RXO0_C
8 -RXO0_C
9 +RXE3_C
10 -RXE3_C
401
No. Pin Define
11 +RXE2_C
12 -RXE2_C
13 +RXE1_C
14 -RXE1_C
15 +RXE0_C
16 -RXE0_C
17 GND
18 LCD_VCC
19 LCD_VCC
20 LCD_VCC
NOTE! Cable detect pin 24 must connect to ground.
No. Pin Define
21 No Connect
22 VCC3
23 GND
24 -Cable Detect
25 GND
26 +RXECLKO_C
27 -RXECLKO_C
28 GND
29 GND
30 GND
No. Pin Define
31 SMB_CLK_CON
32 SC_BKLT_EN
33 SC_BKLT_CTRL
34 +RXECLKE_C
35 -RXECLKE_C
36 FPD_19V
37 FPD_19V
38 FPD_19V
39 No Connect
40 SMB_DATA_CON
18
Flat Panel Display Connector
No. Pin Define
1 Backlight enable
2 Backlight control
3 Backlight inverter power
4 Backlight inverter power
5 GND
6 GND
7 Panel brightness increase
8 Panel brightness decrease
Front Audio Connector/ 前置音频
2
1
10
9No. Pin Define
1 MIC2_L
2 GND
3 MC2_R
4 FP_AUDIO_DET
5 LINE2_R
No. Pin Define
6 MIC2_JD
7 GND
8 No Pin
9 LINE2_L
10 LINE2_JD
Speaker Cable Connector
No. Pin Define
1 Speaker Out R-
2 Speaker Out R+
3 Speaker Out L+
4 Speaker Out L-
41
Back Light Switch Header
21
No. Pin Define
1 Back light down
2 Back light up
Baery Cable Connector
No. Pin Define
1 Baery+
2 GND
2 1
CPU/System FAN/
1
1
4
4
No. Pin Define
1 GND
2 +12V
3 Sense
4 Speed Control
Monitor Power Switch
No. Pin Define
1 High/Low: turn on/off monitor
2 GND
2
1
Digital MIC In Connector
5
1
No. Pin Define
1 VCC
2 DMIC DATA
3 GND
4 DMIC CLK
5 No Pin
No. Desripon
1 Clear CMOS Jumper
Open: Normal operaon (Default seng)
Close: Clear CMOS data.
2 LVDS Back Light Power Select Jumper
1-2 Close: Set to 12V.
2-3 Close: Set to 19V. (Default seng)
3 LVDS Logic/LCD Drive Voltage Jumper
1-2 Close: Set to 3V.
2-3 Close: Set to 5V. (Default seng)
Jumper Sengs/ 跳线设置
23
1
1 2
3 4 76
5 5