Bauknecht WBKI75430 Daily Reference Guide

ブランド: Bauknecht

モデル: WBKI75430

カテゴリー: 洗濯機

タイプ: Daily Reference Guide

www.bauknecht.com.hk

Model : WBKI75430

產品型號

WBKI75430

產品安全指引、使用說明及安裝指南

繁體中文

THANK YOU FOR BUYING A BAUKNECHT PRODUCT.

www.bauknecht.com.hk

Index

USER MANUAL 3

CONTROL PANEL 5

WASH CYCLE TABLE 5

PRODUCT DESCRIPTION 5

DETERGENT DISPENSER 5

WASH CYCLES 6

FIRST-TIME USE 6

DAILY USE 6

PAUSING A CYCLE 6

OPENING THE DOOR, IF NECESSARY 6

CHANGING A RUNNING WASH CYCLE 6

AT THE END OF THE WASH CYCLE 6

OPTIONS 6

KEY LOCK 7

TIPS AND SUGGESTIONS 7

CARE AND MAINTENANCE 7

LOAD BALANCING SYSTEM 7

TROUBLESHOOTING 8

CLEANING AND MAINTENANCE

CLEANING THE OUTSIDE OF THE WASHER-DRYER 9

CHECKING THE WATER SUPPLY HOSE 9

CLEANING THE MESH FILTERS IN THE WATER SUPPLY HOSE 9

CLEANING THE DETERGENT DISPENSER 10

CLEANING THE WATER FILTER / DRAINING RESIDUAL WATER 10

TRANSPORT AND HANDLING 11

AFTER-SALES SERVICE

SAFETY INSTRUCTIONS

INSTALLATION GUIDE

Quick Guide

Before using the appliance carefully read the Health and Safety guide.

Before using the machine, it is imperative that the transport bolts are removed. For more

detailed instructions on how to remove them, see the Installation Guide.

CONTROL PANEL

WASH CYCLE TABLE

For all testing institutes:

2) Long cotton cycle: set programme 5 at temperature 40°C.

* By selecting the cycle and excluding the spin cycle, the washer-dryer will drain only.

The cycle duration indicated on the display or instruction manual is an estimate based on

standard conditions. The actual duration may vary in relation to several factors, such as

the temperature and pressure of the incoming water, ambient temperature, amount of

detergent, load quantity and type, load balancing and any additional options selected.

1) Test programme in compliance with standard EN 50229 (Wash):

both electricity and water consumption; it should be used for garments washable at 60°C.

Test programme in compliance with standard EN 50229 (Drying) : select the wash

programme 10 and set the drying level to “

carried out with the nominal load.

Maximum load 7 kg

Detergents and

Additives

Recommended

detergent

Wash cycle

Temperature(°C)

Maximum

spin

(r.p.m.)

Max.

load

(kg)

Default

cycle duration

(hh : mm)

Drying

Dry

only

Energy

saver

Wash

Fabric

softener

Powder Liquid

Default Range

2 3

1 40 °C

800 –

2 40 °C

40 °C

1000 –

3 – – – – – – –

4 – – – – – – –

40 °C

- 60 °C 1400

6 40 °C

- 60 °C 1200

7 40 °C

- 40 °C 1200 –

8 40 °C

- 40 °C 1400 –

9 60 °C

- 90 °C 1400

10 60 °C

- 60 °C 1400

11 40 °C

- 40 °C 1400 –

12 30 °C

- 30 °C 0 –

13 40 °C - 40 °C 800 –

14 30 °C

- 30 °C 800 –

– – 1400

–

– –

Daily Mix Wash&Dry

Shirts & T-Shirts

Pre Iron

Steam Refresh

Cotton (2)

Synthetics

Anti Stain Quick

Anti Stain 100

White

Eco Cotton

(1)

Coloureds

Ultradelicates

Wool

Fast 30 min

Rinse + Spin

Spin + Drain* – – 1400

3.5

1.5

3.5

1.5

4:25

3:00

0:20

3:50

3:15

0:45

3:25

2:20

2:55

1:40

1:20

1:15

0:30

0:50

0:10

– – – –

Required dosage Optional dosage

1. ON/OFF button

2. START/PAUSE button

3. TEMPERATURE button

ENERGY SAVER button

DRY ONLY button / Lock

button

6. DRYING SETTINGS button

7. START DELAY button

8. SPIN SPEED button

9. WASH CYCLE SELECTOR KNOB

1 2

DISPLAY INDICATORS

Washing phase

Indicates washing phase of the cycle

Drying phase

Energy Saver activated

Key lock activated

Drying only

Time drying mode

Drying automatic levels

Start delay activated

Door locked

PRODUCT DESCRIPTION

1. Worktop

2. Detergent dispenser

3. Control panel

4. Door handle

5. Door

7. Adjustable feet (4)

DETERGENT DISPENSER

Compartment 1:

Do not insert detergent in this compartment.

Compartment 2: Washing detergent

(powder or liquid)

Compartment 3: Additives (fabric softeners,

etc.)

The fabric softener must not exceed the “MAX”

level.

! Use powder detergent for white cotton

garments, for pre-washing, and for washing at

temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

–

– –

–

40 °C

WASH CYCLES

Follow the instructions on the symbols of the garment’s wash

care label. The value indicated in the symbol is the maximum

recommended temperature for washing the garment.

Daily Mix Wash & Dry

Use programme 1 to wash and dry mixed garments (cotton and

synthetics). This cycle may be used to wash and dry loads of up to 3.5 kg;

we recommend the use of liquid detergent.

The use of the steam in this programme is optimised to reduce the

formation of creases on garments, making them easier to iron.

Shirts & T-Shirts

and colours to ensure maximum care. This cycle may be used to wash and

dry loads of up to 2 kg. To achieve optimum results, use liquid detergent

programme is optimised to reduce the formation of creases on garments,

making them easier to iron.

Pre Iron

Use this programme immediately before ironing; max. 1.5 kg load. The

use of the steam in this programme is optimised to reduce the formation

of creases on garments, making them easier to iron.

Steam Refresh

For refreshing garments, neutralised unpleasant odours and relaxing the

the end of the cycle.

Cotton

Suitable for washing towels, underwear, table cloths, etc, made of

resistant linen and cotton that are moderately to heavily soiled.

Synthetics

Anti Stain Quick

hour. It is ideal for mixed fabrics and coloured garments, caring for your

This

clothes as it washes.

If the drying function is selected, a drying cycle automatically activates at

the end of the wash cycle that resembles open-air drying, with the added

advantages of preserving garments from yellowing due to sunlight

exposure and preventing loss of whiteness caused by the possible

presence of dust in the air. Dryness level “

” recommended.

Anti Stain 100

The programme is suitable to heavily-soiled garments with resistant

colours. It ensures a washing class that is higher than the standard class (A

colours. We recommend the use of powder detergent. Pre-treatment with

special additives is recommended if there are obstinate stains.

If the drying function is selected, a drying cycle automatically activates at

the end of the wash cycle that resembles open-air drying, with the added

advantages of preserving garments from yellowing due to sunlight

exposure and preventing loss of whiteness caused by the possible

presence of dust in the air. Dryness level “ ” recommended.

White

For heavily soiled whites and resistant colours.

Eco Cotton

Suitable for washing moderately soiled cotton garments. At 60°C it is the

terms of combined water and electricity consumption.

Coloureds

For washing coloured cotton garments. This programme is optimised to

keep colours bright even after repeated washing.

Ultradelicates

For washing very delicate garments. We recommend turning the garments

inside out before washing and placing small items into the special bag for

washing delicates. Use liquid detergent on delicate garments for best

results. When selecting an exclusively time-based drying function, a

drying cycle is performed at the end of the wash cycle that is particularly

delicate, thanks to light handling and appropriate temperature control of

the water jet.

The recommended durations are:

1 kg of synthetic garments --> 150 min

1 kg of synthetic and cotton garments --> 180 min

1 kg of cotton garments --> 180 min

The degree of dryness depends on the load and fabric composition.

Wool - Woolmark Apparel Care - Green:

The wool wash cycle of this machine has been approved

by The Woolmark Company for the washing of wool

garments labelled as “hand wash” provided that the

products are washed according to the instructions on the

garment label and those issued by the manufacturer of

this washer-dryer. (M1126)

Fast 30 min

For washing lightly soiled garments in a short time. Not suitable for wool,

silk and garmen

ts to be washed by hand.

Rinse + Spin

Designed for rinsing and spinning.

Spin + Drain

Designed for spinning and draining the water.

Door locked indicator

If the

until the symbol turns on before opening the door.

To open the door while a cycle is in progress, press the START/PAUSE

button

; if the symbol is lit, the door can be opened.

time, run a wash cycle with detergent and no laundry, by setting the cycle

9(60°C).

DAILY USE

Prepare the laundry by following the suggestions appearing under the

“TIPS AND SUGGESTIONS” section.

- Press the ON/OFF button

; the indicator light relative to START/PAUSE

- Open the door. Load the laundry while making sure not to exceed the

maximum load quantity indicated in the “WASH CYCLE TABLE”.

- Pull out the detergent dispenser drawer and pour the detergent into the

relevant compartments, as described in the “DETERGENT DISPENSER”

section.

- Close the door.

- The machine automatically displays the default temperature and spin

speed values for the selected cycle, or the most recently used settings if

they are compatible with the selected cycle.

- Select the desired wash cycle.

- Select the desired options.

- Press the START/PAUSE

button to start the wash cycle; the relative

indicator light will light up steady and the door will lock (

PAUSING A CYCLE

To pause the wash cycle, press the START/PAUSE button again; the

symbol is lit, the door may be opened. To

start the wash cycle from the point at which it was interrupted, press the

START/PAUSE

button again.

OPENING THE DOOR, IF NECESSARY

Once a cycle starts, the

be opened. While a wash cycle is running, the door remains locked. To

open the door while a cycle is under way, for example, to add or remove

garments, press the START/PAUSE

button to pause the cycle; the

symbol is lit, the door may be opened.

Press the START/PAUSE

button again to continue the cycle.

CHANGING A RUNNING WASH CYCLE

To change a wash cycle while it is in progress, pause the washer-dryer using

the START/PAUSE

select the desired cycle and press the START/PAUSE button again.

! To cancel a cycle that has already begun, press and hold the ON/OFF

AT THE END OF THE WASH CYCLE

This will be indicated by the word “END” on the display; when the

symbol switches on, the door may be opened. Open the door, unload the

half of an hour. Close the water tap, open the door and unload

the machine. Leave the door ajar to allow the drum to dry.

OPTIONS

! If the selected option is incompatible with the programme set, the

incompatibility will be signalled by a buzzer and the corresponding

! If the selected option is incompatible with another previously set

option, only the most recent selection will remain active.

Energy Saver

This option saves energy by not heating the water used to wash your

laundry – an advantage both to the environment and to your energy bill.

wash results in the same average time of a standard cycle.

For the best washing results we recommend the usage of a liquid

detergent.

Start Delay

To set the selected programme to start at a later time (30min -24hr), press

the button to set the desired delay time. The

symbol lights on the

display when this function is enabled. To cancel the delayed start, press

the button again until the value “0” is shown on the display.

Temperature

temperature, press the “Temp.” button. The value will appear on the

display.

Spin

press the “Spin Speed” button. The value will appear on the display.

Setting the drying cycle

Drying Settings” is pressed, the machine will

automatically select the maximum drying cycle which is compatible with

the selected wash cycle. Subsequent presses will decrease the drying level

and then the drying time, until the cycle is excluded completely (“OFF”).

Drying may be set as follows:

A- Based on the desired laundry dryness level:

Cupboard

: suitable for laundry which can be put back in a cupboard

without being ironed.

Hanger

: ideal for clothes which do not need to be dried fully.

Iron

: suitable for clothes which will need ironing afterwards. The

remaining dampness softens creases, making them easier to remove.

B - Based on a set time period: between 30-210 minutes.

If your laundry load to be washed and dried is much greater than the

maximum stated load (see “WASH CYCLE TABLE”), perform the wash

cycle, and when the cycle is complete, divide the garments into groups

and put some of them back in the drum. At this point, follow the

instructions provided for a “Drying only” cycle. Repeat this procedure for

the remainder of the load. Note: a cooling-down per

iod is always added to

the end of each drying cycle.

Drying only

Press button “Dry only” to perform the drying-only cycle. After selecting

the desired cycle (compatible with the type of garments), press button

“Dry only” to exclude the washing phase and start the drying phase at the

maximum level for the selected cycle. The drying level or time may be set

and changed by pressing the drying button “Drying Settings”.

KEY LOCK

To lock the control panel, press and hold the button “Dry only” for

approximately 3 seconds. the symbol

lights on the display to indicate

that the control panel is locked (with the exception of the

button). This

prevents unintentional changes to programmes, especially with children

near the machine.

If any attempt is made to use the control panel, the symbol

the display.

To unlock the control panel, press and hold the button “Dry only” for

approximately 3 seconds.

TIPS AND SUGGESTIONS

Divide the laundry according to:

hand-washed). Colour (separate coloured garments from whites, wash

new coloured garments separately). Delicates (small garments – such as

nylon stockings – and items with hooks – such as bras: insert them in a

fabric bag).

Empty the pockets:

Objects such as coins or lighters can damage the washer-dryer and

the drum. Check all buttons.

CARE AND MAINTENANCE

Before performing cleaning and maintenance, switch the washer-dryer

clean the washer-dryer.

Disconnect the water and power supplies

Close the water tap after every wash. This will limit wear on the hydraulic

system inside the washer-dryer and help to prevent leaks.

Unplug the washer-dryer when cleaning it and during all maintenance work.

Clean the washer-dryer

The outer parts and rubber components of the appliance can be cleaned

using a soft cloth soaked in lukewarm soapy water. Do not use solvents or

abrasives.

Clean the detergent dispenser drawer

Wash it under running water; this operation should be repeated

frequently.

Care for the door and drum

Always leave the porthole door ajar in order to prevent unpleasant

odours from forming.

Clean the pump

The washer-dryer is fitted with an auto-cleaning pump that does not require

any maintenance. Small items (such as coins or buttons) may sometimes fall

into the protective pre-chamber situated at the base of the pump.

! Make sure the wash cycle has ended and unplug the appliance.

LOAD BALANCING SYSTEM

Before every spin cycle, to avoid excessive vibrations before every spin and

to distribute the load in an uniform manner, the drum rotates continuously

at a speed which is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly, the machine

spins at a reduced spin speed. If the load is excessively unbalanced, the

washer-dryer performs the distribution process instead of spinning. To

encourage improved load distribution and balance, we recommend small

and large garments are mixed in the load.

TROUBLESHOOTING

Your washer-dryer could occasionally fail to work. Before contacting the After-Sales Service, make sure that the problem cannot be easily

solved using the following list.

Anomalies Possible causes / Solution

The washer-dryer does not

start.

The appliance is not plugged into the socket fully, or not enough to make contact.

There is no power in the house.

The wash cycle does not start.

The washer-dryer door is not closed properly.

The ON/OFF

button has not been pressed.

The START/PAUSE

button has not been pressed.

The water tap has not been opened.

A delay has been set for the start time.

with water (“H2O” appears on

the display).

The water inlet hose is not connected to the tap.

The hose is bent.

The water tap has not been opened.

There is no water supply in the house.

The pressure is too low.

The START/PAUSE

button has not been pressed.

The washer-dryer

continuously loads and

unloads water.

The free end of the hose is immersed in water.

are available in shops and help to prevent this inconvenience.

After-Sales

The washer-dryer does not

drain or spin.

The cycle does not include drainage: with certain cycles it must be started manually.

The drain hose is bent.

The drainage duct is clogged.

The washer-dryer vibrates a

lot during the spin cycle.

The drum was not unlocked correctly during installation.

The washer-dryer is not level.

The washer-dryer is tucked between furniture cabinets and the wall.

The washer-dryer leaks.

The water inlet hose is not screwed on properly.

The detergent dispenser drawer is obstructed.

The drain hose is not properly attached.

The START/PAUSE

and an error code appears on

the display (e.g.: F-01, F-..).

If the problem persists, contact the After-Sales Service.

There is too much foam.

The detergent is not suitable for machine washing (it should display the text “for washer-dryers” or “hand and

machine wash”, or the like).

Too much detergent was used.

The washer-dryer does not

dry.

The appliance is not plugged into the socket, or not enough to make contact.

There has been a power failure.

The appliance door is not shut properly.

A Delay has been set.

DRYING is in the OFF position.

The machine can be heard

taking in water during the

drying cycle.

It is normal for the machine to take in short bursts of water during the drying cycle. This helps keep some internal

parts cool, and aids speed of drying.

You can download the Product Factsheet and User Manual by:

• Visiting the website www.bauknecht.com.hk

• Alternatively, contact our After-Sales Service (the telephone number is indicated in the warranty

booklet). When contacting the After-Sales Service, provide the codes shown on the adhesive label applied

to the inside of the door.

xxxxxxxxxxxx

xxxx

DEMO MODE : To deactivate this function, switch the washer-dryer OFF. Then press and hold “Start/Pause” button, within 5 seconds press also

“ON/OFF”

button and hold both buttons for 2 seconds.

CLEANING AND MAINTENANCE

CLEANING THE OUTSIDE OF THE WASHER-DRYER

Use a soft damp cloth to clean the outer parts of the washer-

dryer.

Do not use glass or general purpose cleaners, scouring

powder or similar to clean the control panel – these

substances might damage the printing.

CHECKING THE WATER SUPPLY HOSE

Check the inlet hose regularly for brittleness and cracks. If

damaged, replace it by a new hose available through our

After-Sales Service or your specialist dealer.

Depending on the hose type:

If the inlet hose has a transparent coating, periodically check

and should be replaced.

For water stop hoses: check the small safety valve inspection

window (see arrow). If it is red, the water stop function was

triggered, and the hose must be replaced by a new one.

For unscrewing this hose, press the release button (if

available) while unscrewing the hose.

CLEANING THE MESH FILTERS IN THE WATER SUPPLY HOSE

1. Close water tap and unscrew the inlet hose.

3. Now unscrew the inlet hose on the back of the washer-dryer

on the back

of the washer-dryer with pliers and

carefully clean it.

water tap and washer-dryer again. Do not use a tool to

connect the inlet hose. Open the water tap and check

that all connections are tight.

washer-dryer

CLEANING THE DETERGENT DISPENSER

CLEANING THE WATER FILTER / DRAINING RESIDUAL WATER

wash programme, wait until the water has cooled down before draining any water.

1. Container for the drained water:

order to collect the residual water.

Drain the water:

Repeat the procedure until all the water has been drained.

which can absorb a small amount of rest water. Then

clean it under running water.

in clockwise direction. Make sure to turn it in as far as it goes; th

detergent dispenser.

Remove the dispenser by raising it and

Wash it under running water; this

operation should be repeated frequently.

washer-dryer

Remove

TRANSPORT AND HANDLING

Never lift the washer-dryer by holding it at the worktop.

1. Pull out the mains plug, and close the water tap.

2. Make sure that door and detergent dispenser are properly

closed.

3. Disconnect the inlet hose from the water tap, and remove

the drain hose from your draining point. Remove all rest

damaged during transport.

removing the transport bolts in the

“ ”

Important: Do not transport the washer-dryer without

1. See if you can solve the problem by yourself with the help

of the suggestions given in the TROUBLESHOOTING

fault persists.

IF AFTER THE ABOVE CHECKS THE FAULT STILL

OCCURS, GET IN TOUCH WITH THE NEAREST

To receive assistance, call the number shown on the warranty

booklet or follow the instructions on the website

www.bauknecht.com.hk

When contacting our After-Sales Service, always specify:

• a brief description of the fault;

• the type and exact model of the appliance;

• the service number (number after the word Service on the

rating plate);

•

your full address;

• your telephone number.

If any repairs are required, please contact an authorised After-

Sales Service (to guarantee that original spare parts will be used

and repairs carried out correctly).

INSTALLATION GUIDE

in reverse order.

xxxxxxxxxxxx

SAFETY INSTRUCTIONS

IMPORTANT TO BE READ AND OBSERVE

Before using the appliance, read these safety in-

structions. Keep them nearby for future reference.

These instructions and the appliance itself provide

important safety warnings, to be observed at all ti-

mes. The manufacturer declines any liability for failure

to observe these safety instructions, for inappropriate

use of the appliance or incorrect setting of controls.

away from the appliance. Young children

appliance unless continuously supervised.

with reduced physical, sensory or mental

capabilities or lack of experience and knowledge

can use this appliance only if they are supervised

or have been given instructions on safe use and

understand the hazards involved. Children must

not play with the appliance. Cleaning and user

maintenance must not be carried out by children

without supervision. Never open the door forcibly

or use it as a step.

PERMITTED USE

CAUTION: The appliance is not intended to be

operated by means of an external switching

device, such as a timer, or separate remote

controlled system.

This appliance is intended to be used in

environments; farm houses; by clients in hotels,

motels, bed & breakfast and other residential

environments.

Do not load the machine above the maximum

capacity (kg of dry cloth) indicated in the

programme table.

This appliance is not for professional use. Do

not use the appliance outdoors.

Do not use any solvents (e.g. turpentine,

benzene), detergents containing solvents,

scouring powder, glass or general purpose

wash fabrics that have been treated with solvents

Do not dry unwashed items in the tumble

dryer.

Items that have been soiled with substances

such as cooking oil, acetone, alcohol, petrol,

kerosene, spot removers, turpentine, waxes and

wax removers should be washed in hot water with

an extra amount of detergent before being dried

in the tumble dryer.

Items such as foam rubber (latex foam), shower

caps, waterproof textiles, rubber backed articles

pads should not be dried in the tumble dryer.

Fabric softeners, or similar products, should be

instructions.

without heat (cool down cycle) to ensure that the

items are left at a temperature that ensures that

the items will not be damaged.

Never stop a tumble dryer before the end of

the drying cycle unless all items are quickly

removed and spread out so that the heat is

dissipated.

During the drying phase, the door tends to get

quite hot.

Do not use the appliance to dry clothes that

trichlorethylene).

Do not use the appliance to dry foam rubber or

similar elastomers.

Make sure that the water tap is turned on

during the drying cycles.

Remove all objects from pockets such as

lighters and matches.

INSTALLATION

The appliance must be handled and installed

cuts.

If you want to stack a dryer on top of your

Service or your specialist dealer to verify whether

this is possible. This is only possible if the dryer is

attached to the machine by means of

appropriate

stacking kit available through our

After- Sales

Service or your specialist dealer.

Move the appliance without lifting it by the

worktop or top lid.

Installation, including water supply (if any) and

electrical connections and repairs must be carried

replace any part of the appliance unless

children away from the installation site. After

unpacking the appliance, make sure that it has not

been damaged during transport. In the event of

problems, contact the dealer or your nearest

After-Sales Service. Once installed, packaging

waste (plastic, styrofoam parts etc.) must be

The appliance must be disconnected from the

risk of electric shock. During installation, make

sure the appliance does not damage the power

the appliance when the installation has been

completed.

Do not install your appliance where it may be

exposed to extreme conditions, such as: poor

ventilation, temperatures below 5 °C or above 35 °C.

When installing the appliance make sure that

adjusting them as required, and check that the

appliance is perfectly to level using a spirit level.

If the appliance is being installed on wood or

on top of this.

Connect the water inlet hose(s) to the water

supply in accordance with the regulations of your

local water company.

hot water supply.

bolts to prevent any possible damage to the

interior during transport. Before using the

machine, it is imperative that the transport bolts

are removed. After their removal, cover the

openings with the 4 enclosed plastic caps.

After installation of the device, wait a few

hours before starting it so that it acclimates to the

environmental conditions of the room.

Make sure that the ventilation openings in the

base of your washer-dryer (if available on your

model) are not obstructed by a carpet or other

material.

Use only new hoses to connect the appliance

to the water supply. The old hose-sets should not

be reused.

The supply water pressure must be in the 0.1-1

Mpa range.

ELECTRICAL WARNINGS

It must be possible to disconnect the appliance

from the power supply by unplugging it if plug is

accessible, or by a multi-pole switch installed

upstream of the socket in accordance with the

wiring rules and the appliance must be earthed in

conformity with national electrical safety

standards.

Do not use extension leads, multiple sockets or

adapters. The electrical components must not be

accessible to the user after installation. Do not use

the appliance when you are wet or barefoot. Do

not operate this appliance if it has a damaged

power cable or plug, if it is not working properly,

or if it has been damaged or dropped.

If the supply cord is damaged, it must be

replaced with an identical one by the

manufacturer, its service agent or similarly

of electric shock.

CLEANING AND MAINTENANCE

WARNING: Ensure that the appliance is

supply before performing any maintenance

risk of electric shock.

DISPOSAL OF PACKAGING MATERIALS

The packaging material is 100% recyclable and is marked with the

recycle symbol

The various parts of the packaging must therefore be disposed of

responsibly and in full compliance with local authority regulations

governing waste disposal.

DISPOSAL OF HOUSEHOLD APPLIANCES

This appliance is manufactured with recyclable or reusable materials.

Dispose of it in accordance with local waste disposal regulations.

For further information on the treatment, recovery and recycling

of household electrical appliances, contact your local authority,

the collection service

for

household waste or the store where you

purchased the appliance. This appliance is marked in compliance

with European Directive 2012/19/EU, Waste Electrical and Electronic

Equipment (WEEE). By ensuring this product is disposed of correctly,

you will help prevent negative consequences for the environment and

human health.

The symbol

on the product or on the accompanying documentation

indicates that it should not be treated as domestic waste but must be

taken to an appropriate collection center for the recycling of electrical

and electronic equipment.

4. 5.

150 ml

100 ml

50 ml

10 mm - 0.39 inch

2 cm - 0.7 inch

INSTALLATION GUIDE

10. 11.

12.

13.

14.

max 100 cm

39 inch

min 65 cm

25 inch

max 100 cm

39 inch

min 65 cm

25 inch

max 100 cm

39 inch

min 65 cm

25 inch

9.8.

max 0.5 cm

max 0.2 inch

INSTRUCTIONS FOR THE FITTER

Mounting the wooden panel onto the door

and inserting the machine into cabinets:

In the case where the machine must be shipped

been mounted, we suggest leaving it in its

original packaging. The packaging was designed

to make it possible to mount the wooden panel

onto the machine without removing it

completely

The wooden panel that covers the face of the

machine must not be less than 13 mm in

thickness and can be hinged on either the right

or left. For the sake of practicality when using the

machine, we recommend that the panel be

hinged on the same side as the door for the

machine itself - the left.

Door Mounting Accessories

(Fig. 1-2-3-4-5).

Fig. 1

N° 2 Hinges

N° 1 Magnet N° 1 Magnet plate

N° 1 Rubber plug

N° 2 Hinge Supports

N° 4 Spacers

Fig. 2

Fig. 3 Fig. 4

Fig. 5

Fig. 4/B

- No. 6 type A self-threading screws, l =13 mm.

- N

o. 2 type B metric, countersunk screws, l =25mm;

for fastening the magnet plate to the cabinet.

- No. 4 type C metric screws, l =15 mm; for

mounting the hinge supports to the cabinet.

- No. 4 type D metric screws, l =7 mm; for

mounting the hinges on the supports.

Mounting the Parts onto the Face of the

Machine.

- Fit the hinge supports to the appliance front

panel, positioning the hole marked with an arrow

so that it is on the inner side of the front

panel. Fit a spacer (

between the surfaces

using type C screws.

- Fit the magnet plate at the top of the opposite

side, using type B

4/B) between the plate and the surface.

Using the Drilling Template.

- To trace the positions of the holes on the left-

hand side of the panel, align the drilling template

to the top left side of the panel using the lines

traced on the extremities as a reference.

- To trace the positions of the holes on the right-

hand side of the panel, align the drilling template

to the top right side of the panel.

- Use an appropriately sized router to mill the holes

for the two hinges, the rubber plug and the magnet.

Mounting the Parts

onto the Woode

n Panel (Door).

- Insert the hinges into the holes (the movable part

of the hinge must be positioned facing away from

the panel) and fasten them with the 4 type A screws.

- Insert the magnet into the top hole on the

opposite side of the hinges and fasten it with the

two type B screws.

- Insert the rubber plug into the bottom hole.

The panel is now ready to be mounted onto the

machine.

Mounting the Panel into the machine.

Insert the nib of the hinge

(indicated by the arrow

) into the hole for the hinge and push the

panel towards the front of the machine. Fasten

the two hinges with the type D screws.

Fastening the plinth guide.

If the machine is installed at the end of a set of

modular cabinets, mount either one or both of the

guides for the base molding (as shown in

Adjust them for depth based on the position of

the base molding, and, if necessary, fasten the

base to the guides

This is how to assemble the plinth guide

Fasten angle P using screw R, insert plinth guide Q

into the special slot and once it is in the desired

position, lock it in place using angle P and screw R.

Inserting the machine into the Cabinet.

- Push the machine into the opening, aligning it

with the cabinets

- Regulate the adjustable feet to raise the machine

to the appropriate height.

- To adjust the position of the wooden panel in

both the vertical and horizontal directions, use the

C and D screws, as shown in

Important: close the lower part of the appliance front

Fig. 8 Fig. 9

Accessories provided for the height adjustment.

The following can be found

inside the polystyrene lid

10): 2 crossbars (G), 1 strip

(M)

The following can be found

inside the appliance drum:

4 additional feet (H),

4 screws (I),

4 screws (R),

4 nuts (L),

2 plinth guides (Q)

Adjusting the appliance height.

The height of the appliance can be adjusted (from

815 mm to 835 mm), by turning the 4 feet.

Should you require the appliance to be placed

higher than the above height, you need to use the

following accessories to raise it to up to 870 mm:

the two crossbars (G); the 4 feet (H); the 4 screws

(I); the 4 nuts (L) then perform the following

operations

Remove the 4 original feet, place a crossbar G at

the front of the appliance, fastening it in place

using screws I (screwing them in where the original

feet were) then insert the new feet H.

Repeat the same operation at the back of the

appliance.

Now adjust feet H to raise or lower the appliance

from 835 mm to 870 mm.

Once you have reached the desired height, lock

nuts L onto crossbar G.

To adjust the appliance to a height between 870

mm and 900 mm, you need to mount strip M,

adjusting feet H to the required height.

Insert the strip as follows:

loosen the three screws N situated at the front of

the Top cover of the appliance, insert strip M as

shown in

, then fasten screws N.

Fig. 6 Fig. 7

Fig. 11 Fig. 12

570

min

518

545

595

009 ÷ 028

600 min

Fig. 10

11338878

索引

使用說明 

控制面板 20

程序表 20

產品介紹 20

洗衣劑盒 20

洗衣程序 21

首次使用 21

日常使用 21

暫停程序 21

打開機門 (如有需要) 21

變更正在運行的程序 21

洗衣程序結束 21

選項 22

兒童安全鎖 22

提示及應用 22

保養和維護 22

衣物平衡系統 22

故障排除 23

清潔和保養

清潔洗衣乾衣機的外部 24

檢查進水喉 24

清潔進水喉內的濾網 24

清潔洗衣劑盒 25

清潔濾網/排走積水 25

繁體中文

產品安全指引、使用說明及安裝指南

感謝您購買Bauknecht產品

為了獲得更完善的服務，

請於www.bauknecht.com.hk註冊您的產品

搬運和處理 26

售後服務 26

安全指引

安裝指南

在顯示器上或說明書中的程序時間是以標準的情況下計算，實際程序時間會因不同的因素自

動調整，如進水溫度和水壓，環境溫度，洗衣劑量，衣物的類型，負載平衡及附加選項等。

1)符合標準EN50229(洗衣)測試程序：

該程序的設計用於一般骯髒的棉質衣物負載，並且在能源和水消耗方面是最有效的；它應

該用於可用60°C清洗的衣物。實際的清洗溫度可能與指示值不同。

符合標準EN50229(乾衣)測試程序：選擇「棉質節能洗」程序及設定一般乾衣程度“ ”。

首次負載會根據額定的負載量進行。

需要使用洗衣劑選擇性使用洗衣劑

最大負載量7公斤

最高脫水

轉速

(轉/分鐘)

最大洗

衣量

(公斤)

乾衣

功能

主洗

柔順劑

洗衣粉

獨立

洗衣

節約

能源

選項

洗衣液

預設程序

時間

(小時:分鐘)

洗衣劑和添加劑

建議洗衣劑類別

程序

預設範圍

能源標籤測試程序

2) 較長的棉質程序：使用40°C的「棉質」程序 (程序5)。

* 當選擇脫水及排水程序時，若免去脫水程序，洗衣乾衣機只會進行排水程序。

1. 電源「開/關」鍵

2. 「啟動/暫停」鍵

3. 「溫度」鍵

4. 「節約能源」鍵

5. 「乾衣」鍵 /

「兒童安全鎖」鍵

6. 「乾衣選項」鍵

7. 「預校開機時間」鍵

8. 「脫水轉速」鍵

9. 「程序」旋鈕

1. 頂板

2. 洗衣劑盒

3. 控制面板

4. 機門門把

5. 機門

6. 底座

7. 可調機腳(4)

預洗格(1):

請勿在此預洗格中放入洗衣劑。

主洗格(2)：洗衣劑

(洗衣粉或洗衣劑)

柔順劑格(3)：添加劑 (如：衣物柔順劑)。

添加劑只能添加到“MAX”標誌。

! 白色棉質衣物：請使用洗衣粉，以及在超過

60°C的溫度下進行清洗。

! 請按照洗衣劑包裝上的說明進行操作。

控制面板

程序表

產品介紹洗衣劑盒

使用洗衣乾衣機前請先細閱產品安全指引。

在使用洗衣乾衣機之前，必須卸下運輸螺栓。有關如何移除它們，更詳

細說明，請參閱「安裝指南」。

顯示屏指示燈

洗衣階段指示

該指示顯示當前的洗衣階段

乾衣階段指示

「節約能源」啟動

「兒童安全鎖」啟動

獨立乾衣

「乾衣時間模式」

「乾衣選項」

「預校開機時間」啟動

「開門提示燈」

溫度(°C )

混合衣物洗連乾

襯衫和T恤

蒸氣預熨

蒸氣護理

棉質(2)

合成纖維

快速除漬

除漬100

白色衣物

棉質節能洗

(

)

顏色衣物

纖細衣物

羊毛/手洗

30分鐘速洗

過水及脫水

脫水及排水

40°C

60°C

40°C

30°C

40°C

30°C

- 60°C

- 40°C

- 90°C

- 60°C

- 40°C

- 30°C

- 40°C

- 30°C

800

1000

1400

1200

1400

800

1400

3.5

1.5

3.5

1.5

4:25

3:00

0:20

3:50

3:15

0:45

3:25

2:20

2:55

1:40

1:20

1:15

0:30

0:50

0:10

40°C

ページが読み込まれています...

Bauknecht WBKI75430 Daily Reference Guide

ブランド: Bauknecht

モデル: WBKI75430

カテゴリー: 洗濯機

タイプ: Daily Reference Guide

PDFをダウンロードします

報告

他の言語で

English: Bauknecht WBKI75430

Bauknecht WBKI75430 Daily Reference Guide

Bauknecht WBKI75430 Daily Reference Guide

他の言語で

その他のドキュメント