Whirlpool WFCI75430 Washer Dryer インストールガイド
- カテゴリー
- 洗濯機
- タイプ
- インストールガイド
Model : WFCI75430
產品型號 : WFCI75430
產品安全指引、使用說明及安裝指南
2
繁體中文
3
18
3
Index
USER MANUAL 3
CONTROL PANEL 5
WASH CYCLE TABLE 5
PRODUCT DESCRIPTION 5
DETERGENT DISPENSER 5
WASH CYCLES 6
FIRST-TIME USE 6
DAILY USE 6
PAUSING A CYCLE 6
OPENING THE DOOR, IF NECESSARY 6
CHANGING A RUNNING WASH CYCLE 6
END OF THE CYCLE 6
OPTIONS 6
CHILD LOCK 7
TIPS AND SUGGESTIONS 7
CARE AND MAINTENANCE 7
LOAD BALANCING SYSTEM 7
TROUBLESHOOTING 8
CLEANING AND MAINTENANCE 9
CLEANING THE OUTSIDE OF THE WASHER-DRYER 9
CHECKING THE WATER SUPPLY HOSE 9
CLEANING THE MESH FILTERS IN THE WATER SUPPLY HOSE 9
4
CLEANING THE DETERGENT DISPENSER 10
CLEANING THE WATER FILTER / DRAINING RESIDUAL WATER 10
TRANSPORT AND HANDLING 11
AFTER-SALES SERVICE 11
SAFETY INSTRUCTIONS 12
INSTALLATION GUIDE 14
5
GB
Quick Guide
CONTROL PANEL
Before using the appliance carefully read the Safety Instruction.
Before using the machine, it is imperative that the transport bolts are removed.
For more detailed instructions on how to remove them, see the Installation Guide.
DETERGENT DISPENSER
Compartment 1: Pre-wash detergent
(powder)
Compartment 2: Washing detergent
(powder or liquid)
Compartment 3: Additives (fabric softeners,
etc.)
The fabric softener must not exceed the “MAX”
level.
! Use powder detergent for white cotton
garments, for pre-washing, and for washing at
temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
1
2
3
PRODUCT DESCRIPTION
1. Worktop
2. Detergent dispenser
3. Control panel
4. Door handle
5. Door
6.
7. Adjustable feet (4)
1.
3.
2.
5.
4.
6.
7.
1.
2. Programme selector
3. Start/Pause button
4. Temperature button
5. FreshCare+ button
6. Dry Only button / Lock button
7. Drying settings button
8. Display
9. Start delay button
10. Spin speed button
21 9
3
4
10 6
5
7
8
DISPLAY INDICATORS
Washing phase
Indicates washing phase of the cycle
Drying phase
FreshCare+ activated
Key lock activated
Drying only
Timer drying mode
Drying automatic levels
Start delay activated
Door locked
* Select the programme and set the spin speed to “0“ to drain only.
The cycle duration indicated on the display or in the manual is an estimated time calculated for
such as inlet water temperature and pressure, ambient temperature, quantity of detergent, size
and type of load, load balancing and any additional optional functions selected.
6th Sense - the sensor technology adapts water, energy and programme duration to your
wash load.
For wash programmes with temperatures above 50°C, we recommend using powder
detergent rather than liquid, and following the directions given on the detergent package.
For all Test Institutes
1) Test programme in compliance with standard EN 50229 (Wash): select the “ ”
programme with a temperature of 60°C.
2) Long cotton programme: set the “ “ programme with a temperature of 40°C.
3) Synthetic program along: set the “ “ programme with a temperature of 40°C.
Test programme in compliance with standard EN 50229 (Drying): select the “ “ wash
programme and set the drying level to “
carried out with the nominal load.
WASH CYCLE TABLE
Maximum load 7 kg Detergents and additives Recommended
detergent
Programme
Required dosage Optional dosage
Max. spin
speed
(rpm)
MIXED
COTTON (2)
SYNTHETICS (3)
RAPID 30’
SPORT
WASH&DRY 45 min
WASH & DRY 90
min
SPIN & DRAIN *
RINSE & SPIN
WHITE
ECO COTTON (1)
WOOL
DELICATES
COLOUR 15°
1000
1400
1200
800
600
1400
1200
1400
1400
1400
1400
800
0
1000
1:00
3:50
3:15
0:30
1:30
0:45
1:30
0:10
0:50
2:50
2:55
1:15
1:20
1:30
4.5
7
4.5
3.5
4
1
2
7
7
7
7
2
1
4.5
Max. load
for wash
cycle (kg)
4.5
5
4.5
-
4
1
2
5
5
5
5
2
1
4.5
Max. load
for drying
cycle (kg)
Default
wash cycle
duration
(hh:mm)
Available
temperatures
- 40°C
- 60°C
- 60°C
- 30°C
- 40°C
30°C
30°C
-
-
- 90°C
- 60°C
- 40°C
- 30°C
15°C
Drying
-
Liquid
-
-
Fresh
Care+
-
-
-
-
-
-
Dry
Only
-
-
-
-
-
-
-
-
-
-
-
-
-
Powder
Softener
3
-
Main
-
-
2
Prewash
-
-
-
-
-
-
-
-
-
(90°)
-
-
-
-
1
6
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Mixed
For washing lightly to normally soiled resilient garments in cotton, linen,
For
For
For
Cotton
For washing normally to heavily soiled towels, underwear, table and bed
linen etc. in resilient cotton and linen.
Synthetics
polyester, polyacrylic, viscose etc.) or cotton/synthetic blends.
Rapid 30’
For washing lightly soiled garments quickly: this cycle lasts only 30 minutes,
saving time and energy. Maximum load 3.5 Kg.
Sport
For washing lightly soiled sports clothing (tracksuits, shorts, etc.). For best
results, we recommend not exceeding the maximum load indicated in
the ‘‘WASH CYCLE TABLE‘‘. We recommend using liquid detergent , and
adding the amount suitable for half-load.
Wash&Dry 45 min
quickly. This cycle washes and dries a laundry load of up to 1 Kg in just 45
minutes.
Wash & Dry 90 min
cycle washes and dries a laundry load of up to 2 Kg in just 90 minutes.
Spin & Drain
Spins the load then empties the water. For resilient garments.
Rinse & Spin
Rinses and then spins. For resilient garments.
White
For washing normally to heavily soiled towels, underwear, table and bed linen,
etc in resilient cotton and linen. Only when the temperature is selected at 90°C
the cycle is provided with a prewash phase before main washing phase. In this
case it is recommended to add detergent both, in the prewash and main wash
sections.
Eco Cotton
For washing normally soiled cotton garments. At 40°C and 60°C, this is the
energy consumption.
Wool
All wool garments can be washed using programme “Wool“ even those
in terms of water and
carrying the “hand-wash only “ label. For best results, use special detergents
and do not exceed max kg declaration of laundry.
Delicates
For washing particularly delicate garments. Preferably turn garments inside
out before washing.
Colour 15°
This cycle helps protect colours by washing in cold water (15°C) and uses
comparable to 40°C mixed at just 15°C
Door locked indicator
If the
until the symbol turns on before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE
button ; if the symbol is lit, the door can be opened.
run a wash cycle with detergent and no laundry, using the wash cycle (60°).
DAILY USE
Prepare the laundry by following the suggestions appearing under the
“TIPS AND SUGGESTIONS” section.
- Press the ON/OFF button ; the START/PAUSE indicator light will
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the “WASH CYCLE TABLE”.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments as described in “DETERGENT DISPENSER” section.
- Close the door.
- Use the WASH CYCLE selector knob to select the desired wash cycle: it
- The machine automatically displays the default temperature and spin
speed values for the selected cycle, or the most recently used settings if
they are compatible with the selected cycle.
- Select the drying cycle if desired.
- Select the desired options.
- Press the START/PAUSE button to start the wash cycle; the relative
indicator light will light up steady and the door will lock (
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE button again; the
symbol is lit, the door may be opened. To
start the wash cycle from the point at which it was interrupted, press the
START/PAUSE button again.
OPENING THE DOOR, IF NECESSARY
Once a cycle starts, the
be opened. While a wash cycle is running, the door remains locked. To
open the door while a cycle is under way, for example, to add or remove
garments, press the START/PAUSE button to pause the cycle; the
symbol is lit, the door may be opened.
Press the START/PAUSE button again to continue the cycle.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the machine using
the START/PAUSE button (the relative indicator light will ash), then
select the desired cycle and press the START/PAUSE button again.
! To cancel a cycle that has already begun, press and hold the ON/OFF
END OF THE CYCLE
This will be indicated by the word “END” on the display; when the
symbol switches on, the door may be opened. Open the door, unload the
hour. Close the water tap, open the door and unload the machine. Leave
half of an
the door ajar to allow the drum to dry.
OPTIONS
! If the selected option is incompatible with the programme set, the
incompatibility will be signalled by a buzzer and the corresponding
! If the selected option is incompatible with another previously set
option, only the most recent selection will remain active.
Freshcare+
If associated with wash cycles, this option increases their performances by
generating steam to block proliferation of the main sources of unpleasant
odours inside the appliance (exclusively for the wash). After the steam
phase, the machine runs a delicate cycle with slow drum rotations. When
the Freshcare+ option is associated with drying cycles, it prevents
stubborn creases from stabilising on garments, thanks to slow drum
rotations.
The FreshCare+ cycle starts at the end of the wash or drying cycle and
continues for maximum 6 hours; it can be interrupted at any time by
pressing any button on the control panel, or by turning the knob. Wait
roughly 5 minutes before opening the door.
Start delay
To set the selected programme to start at a later time, press the button to
set the desired delay time. The
h.
symbol lights on the display when this
function is enabled. To cancel the delayed start, press the button again
until the value “0” is shown on the display.
Temperature
temperature, press the “Temp.” button. The value will appear on the
display.
Spin
press the “Spin speed” button. The value will appear on the display.
Setting the drying cycle
“Drying settings” is pressed, the machine will
automatically select the maximum drying cycle which is compatible with
the selected wash cycle. Subsequent presses will decrease the drying level
and then the drying time, until the cycle is excluded completely (“OFF”).
Drying may be set as follows:
A- Based on the desired laundry dryness level:
Cupboard : suitable for laundry which can be put back in a cupboard
without being ironed.
Hanger : ideal for clothes which do not need to be dried fully.
Iron : suitable for clothes which will need ironing afterwards, the
remaining dampness softens creases, making them easier to remove.
B - Based on a set time period: between 30-210 minutes.
If your laundry load to be washed and dried is much greater than the
maximum stated load (see “WASH CYCLE TABLE” ), perform the
wash cycle, and when the cycle is complete, divide the garments into
groups and put some of them back in the drum.
Suitable for lightly soiled, unstained garments. This cycle oers wash results
7
At this point, follow the instructions provided for a “Drying only” cycle.
Repeat this procedure for the remainder of the load. Note: a cooling-down
period is always added to the end of each drying cycle.
Drying only
Press button “Dry only” to perform the drying-only cycle. After selecting
the desired cycle (compatible with the type of garments), press button
“Dry only” to exclude the washing phase and start the drying phase at the
maximum level for the selected cycle. The drying level or time may be set
and changed by pressing the drying button “Drying settings”.
CHILD LOCK
To lock the control panel, press and hold the button “Dry only” for
approximately 3 seconds. the symbol lights on the display to indicate
that the control panel is locked (with the exception of the button). This
prevents unintentional changes to programmes, especially with children
near the machine.
If any attempt is made to use the control panel, the symbol
the display.
To unlock the control panel, press and hold the button “Dry only” for
approximately 3 seconds.
TIPS AND SUGGESTIONS
Divide the laundry according to:
hand-washed). Colour (separate coloured garments from whites, wash
new coloured garments separately). Delicates (small garments – such as
nylon stockings – and items with hooks – such as bras: insert them in a
fabric bag).
Empty the pockets:
Objects such as coins or lighters can damage the washer-dryer and
the drum. Check all buttons.
CARE AND MAINTENANCE
Before performing cleaning and maintenance, switch the washer-dryer
clean the washer-dryer.
Disconnect the water and power supplies
Close the water tap after every wash. This will limit wear on the hydraulic
system inside the washer-dryer and help to prevent leaks.
Unplug the washer-dryer when cleaning it and during all maintenance work.
Clean the washer-dryer
The outer parts and rubber components of the appliance can be cleaned
using a soft cloth soaked in lukewarm soapy water. Do not use solvents or
abrasives.
Care for the door and drum
Always leave the porthole door ajar in order to prevent unpleasant
odours from forming.
LOAD BALANCING SYSTEM
Before every spin cycle, to avoid excessive vibrations before every spin and
to distribute the load in a uniform manner, the drum rotates continuously
at a speed which is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly, the machine
spins at a reduced spin speed. If the load is excessively unbalanced, the
washer-dryer performs the distribution process instead of spinning. To
encourage improved load distribution and balance, we recommend small
and large garments are mixed in the load.
8
TROUBLESHOOTING
The machine may occasionally fail to work. Before contacting the After-Sales Service, make sure that the problem cannot be easily
solved using the following list.
Anomalies Possible causes / Solution
The washer-dryer does
not start. There is no power in the house.
The wash cycle does not start.
The washer-dryer door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delay has been set for the start time.
The washer-dryer does
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The washer-dryer
continuously loads and
unloads water.
The free end of the hose is immersed in water.
The wall drainage system does not have a breather pipe.
valves are available in shops and help to prevent this inconvenience.
The washer-dryer does
not drain or spin.
The cycle does not include drainage: with certain cycles it must be started manually.
The drain hose is bent.
The drainage duct is clogged.
The washer-dryer
vibrates a lot during the spin
cycle.
The drum was not unlocked correctly during installation.
The washer-dryer is not level.
The washer-dryer is tucked between furniture cabinets and the wall.
The washer-dryer leaks.
The water inlet hose is not screwed on properly.
The detergent dispenser drawer is obstructed.
The drain hose is not properly attached.
The “Options” and START/
PAUSE indicator lights
visualises an error code (e.g.:
F-01, F-...).
If the problem persists, contact the After-Sales Service .
There is too much foam.
The detergent is not suitable for machine washing (it should be marked with “for washing machine use” or “hand
wash and machine wash” or similar).
Too much detergent was used.
The washer-dryer does not
dry.
The appliance is not plugged into the socket, or not enough to make contact.
There has been a power failure.
The appliance door is not shut properly.
A DELAY TIMER has been set.
DRYING is in the OFF position.
After-Sales Service.
washer-dryer
TROUBLESHOOTING
9
CLEANING AND MAINTENANCE
CLEANING THE OUTSIDE OF THE WASHER-DRYER
Use a soft damp cloth to clean the outer parts of the washer-
dryer.
Do not use glass or general purpose cleaners, scouring
powder or similar to clean the control panel – these
substances might damage the printing.
CHECKING THE WATER SUPPLY HOSE
Check the inlet hose regularly for brittleness and cracks. If
damaged, replace it by a new hose available through our
After-Sales Service or your specialist dealer.
Depending on the hose type:
If the inlet hose has a transparent coating, periodically check
and should be replaced.
For water stop hoses: check the small safety valve inspection
window (see arrow). If it is red, the water stop function was
triggered, and the hose must be replaced by a new one.
For unscrewing this hose, press the release button (if
available) while unscrewing the hose.
CLEANING THE MESH FILTERS IN THE WATER SUPPLY HOSE
1. Close water tap and unscrew the inlet hose.
1
2
2.
3. Now unscrew the inlet hose on the back of the washer-
dryer by hand. Pull out the mesh lter from the valve
on the back of the washer-dryer with pliers and
carefully clean it.
4.
water tap and washer-dryer again. Do not use a tool
to connect the inlet hose. Open the water tap and check
that all connections are tight.
2
1
washer-dryer.
washer-dryer.
10
CLEANING THE DETERGENT DISPENSER
CLEANING THE WATER FILTER / DRAINING RESIDUAL WATER
wash programme, wait until the water has cooled down before draining any water.
1. Container for the drained water:
order to collect the residual water.
2. Drain the water:
Repeat the procedure until all the water has been drained.
3.
which can absorb a small amount of rest water. Then
4.
clean it under running water.
5.
in clockwise direction. Make sure to turn it in as far as it goes; the
detergent dispenser.
Remove the dispenser by raising it and
Wash it under running water; this
operation should be repeated frequently.
1
2
1
2
washer-dryer
11
TRANSPORT AND HANDLING
Never lift the washer-dryer by holding it at the worktop.
1. Pull out the mains plug, and close the water tap.
2. Make sure that door and detergent dispenser are properly
closed.
3. Disconnect the inlet hose from the water tap, and remove
the drain hose from your draining point. Remove all rest
damaged during transport.
4.
removing the transport bolts in the “INSTALLATION GUIDE”
in reverse order.
Important: Do not transport the washer-dryer without
1. See if you can solve the problem by yourself with the help
of the suggestions given in the TROUBLESHOOTING
2.
fault persists.
IF AFTER THE ABOVE CHECKS THE FAULT STILL
OCCURS, GET IN TOUCH WITH THE NEAREST
To receive assistance, call the number shown on the warranty
booklet or follow the instructions on the website
www.whirlpool.com.hk
When contacting our After-Sales Service, always specify:
•a brief description of the fault;
•the type and exact model of the appliance;
xxxxxxxxxxxx
•the service number (number after the word Service on the
rating plate);
•your full address;
•your telephone number.
If any repairs are required, please contact an authorised After-
Sales Service (to guarantee that original spare parts will be
used and repairs carried out correctly).
12
SAFETY INSTRUCTIONS IMPORTANT TO BE READ AND OBSERVE
Before using the appliance, read these safety in-
structions. Keep them nearby for future reference.
These instructions and the appliance itself provide
important safety warnings, to be observed at all ti-
mes. The manufacturer declines any liability for failure
to observe these safety instructions, for inappropriate
use of the appliance or incorrect setting of controls.
away from the appliance. Young children
appliance unless continuously supervised.
with reduced physical, sensory or mental
capabilities or lack of experience and knowledge
can use this appliance only if they are supervised
or have been given instructions on safe use and
understand the hazards involved. Children must
not play with the appliance. Cleaning and user
maintenance must not be carried out by children
without supervision. Never open the door forcibly
or use it as a step.
PERMITTED USE
CAUTION: The appliance is not intended to be
operated by means of an external switching
device, such as a timer, or separate remote
controlled system.
This appliance is intended to be used in
environments; farm houses; by clients in hotels,
motels, bed & breakfast and other residential
environments.
Do not load the machine above the maximum
capacity (kg of dry cloth) indicated in the
programme table.
This appliance is not for professional use. Do
not use the appliance outdoors.
Do not use any solvents (e.g. turpentine,
benzene), detergents containing solvents,
scouring powder, glass or general purpose
wash fabrics that have been treated with solvents
Do not dry unwashed items in the tumble
dryer.
Items that have been soiled with substances
such as cooking oil, acetone, alcohol, petrol,
kerosene, spot removers, turpentine, waxes and
wax removers should be washed in hot water with
an extra amount of detergent before being dried
in the tumble dryer.
Items such as foam rubber (latex foam), shower
caps, waterproof textiles, rubber backed articles
pads should not be dried in the tumble dryer.
Fabric softeners, or similar products, should be
instructions.
without heat (cool down cycle) to ensure that the
items are left at a temperature that ensures that
the items will not be damaged.
Never stop a tumble dryer before the end of
the drying cycle unless all items are quickly
removed and spread out so that the heat is
dissipated.
During the drying phase, the door tends to get
quite hot.
Do not use the appliance to dry clothes that
trichlorethylene).
Do not use the appliance to dry foam rubber or
similar elastomers.
Make sure that the water tap is turned on
during the drying cycles.
Remove all objects from pockets such as
lighters and matches.
INSTALLATION
The appliance must be handled and installed
cuts.
If you want to stack a dryer on top of your
machine, rst contact our After-Sales Service or
your specialist dealer to verify whether this
is possible. This is only possible if the dryer is
attached to the machine by means of appropriate
stacking kit available through our After- Sales
Service or your specialist dealer.
Move the appliance without lifting it by the
worktop or top lid.
Installation, including water supply (if any) and
electrical connections and repairs must be carried
replace any part of the appliance unless
children away from the installation site. After
unpacking the appliance, make sure that it has not
been damaged during transport. In the event of
problems, contact the dealer or your nearest
After-Sales Service. Once installed, packaging
waste (plastic, styrofoam parts etc.) must be
The appliance must be disconnected from the
risk of electric shock. During installation, make
sure the appliance does not damage the power
the appliance when the installation has been
completed.
13
Do not install your appliance where it may be
exposed to extreme conditions, such as: poor
ventilation, temperatures below 5 °C or above 35 °C.
When installing the appliance make sure that
adjusting them as required, and check that the
appliance is perfectly to level using a spirit level.
If the appliance is being installed on wood or
on top of this.
Connect the water inlet hose(s) to the water
supply in accordance with the regulations of your
local water company.
hot water supply.
bolts to prevent any possible damage to the
interior during transport. Before using the
machine, it is imperative that the transport bolts
are removed. After their removal, cover the
openings with the 4 enclosed plastic caps.
After installation of the device, wait a few
hours before starting it so that it acclimates to the
environmental conditions of the room.
Make sure that the ventilation openings in the
base of your washer-dryer (if available on your
model) are not obstructed by a carpet or other
material.
Use only new hoses to connect the appliance
to the water supply. The old hose-sets should not
be reused.
The supply water pressure must be in the 0.1-1
Mpa range.
ELECTRICAL WARNINGS
It must be possible to disconnect the appliance
from the power supply by unplugging it if plug is
accessible, or by a multi-pole switch installed
upstream of the socket in accordance with the
wiring rules and the appliance must be earthed in
conformity with national electrical safety
standards.
Do not use extension leads, multiple sockets or
adapters. The electrical components must not be
accessible to the user after installation. Do not use
the appliance when you are wet or barefoot. Do
not operate this appliance if it has a damaged
power cable or plug, if it is not working properly,
or if it has been damaged or dropped.
If the supply cord is damaged, it must be
replaced with an identical one by the
manufacturer, its service agent or similarly
of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is
supply before performing any maintenance
risk of electric shock.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the
recycle symbol .
The various parts of the packaging must therefore be disposed of
responsibly and in full compliance with local authority regulations
governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials.
Dispose of it in accordance with local waste disposal regulations.
For further information on the treatment, recovery and recycling
of household electrical appliances, contact your local authority,
the collection service for household waste or the store where you
purchased the appliance. This appliance is marked in compliance
with European Directive 2012/19/EU, Waste Electrical and Electronic
Equipment (WEEE). By ensuring this product is disposed of correctly,
you will help prevent negative consequences for the environment and
human health.
The symbol on the product or on the accompanying documentation
indicates that it should not be treated as domestic waste but must be
taken to an appropriate collection center for the recycling of electrical
and electronic equipment.
The washer dryer
14
1. 2. 3.
4. 5.
150 ml
100 ml
50 ml
10 mm - 0.39 inch
6. 7.
2 cm - 0.7 inch
INSTALLATION GUIDE
15
10. 11.
12.
13. 14.
max 100 cm
39 inch
min 65 cm
25 inch max 100 cm
39 inch
min 65 cm
25 inch
max 100 cm
39 inch
min 65 cm
25 inch
9.8.
max 0.5 cm
max 0.2 inch
16
INSTRUCTIONS FOR THE FITTER
Mounting the wooden panel onto the door
and inserting the machine into cabinets:
In the case where the machine must be shipped
been mounted, we suggest leaving it in its
original packaging. The packaging was designed
to make it possible to mount the wooden panel
onto the machine without removing it
completely
The wooden panel that covers the face of the
machine must not be less than 13 mm in
thickness and can be hinged on either the right
or left. For the sake of practicality when using the
machine, we recommend that the panel be
hinged on the same side as the door for the
machine itself - the left.
Door Mounting Accessories (Fig. 1-2-3-4-5).
Fig. 1
N° 2 Hinges
N° 1 Magnet N° 1 Magnet plate
N° 1 Rubber plug
N° 2 Hinge Supports
N° 4 Spacers
Fig. 2
Fig. 3 Fig. 4
Fig. 5 Fig. 4/B
- No. 6 type A self-threading screws, l =13 mm.
- No. 2 type B metric, countersunk screws
, l =25mm;
for fastening the magnet plate to the cabinet.
- No. 4 type C metric screws, l =15 mm; for
mounting the hinge supports to the cabinet.
- No. 4 type D metric screws, l =7 mm; for
mounting the hinges on the supports.
Mounting the Parts onto the Face of the
Machine.
- Fit the hinge supports to the appliance front
panel, positioning the hole marked with an arrow
in so that it is on the inner side of the front
panel. Fit a spacer ( between the surfaces
using type C screws.
- Fit the magnet plate at the top of the opposite
side, using type B
4/B) between the plate and the surface.
EN
AB
CD
E
Tur seite
17
Using the Drilling Template.
- To trace the positions of the holes on the left-
hand side of the panel, align the drilling template
to the top left side of the panel using the lines
traced on the extremities as a reference.
- To trace the positions of the holes on the right-
hand side of the panel, align the drilling template
to the top right side of the panel.
- Use an appropriately sized router to mill the holes
for the two hinges, the rubber plug and the magnet.
Mounting the Parts onto the Wooden Panel (Door).
- Insert the hinges into the holes (the movable part of
the hinge must be positioned facing away from the
panel) and fasten them with the 4 type A screws.
- Insert the magnet into the top hole on the opposite
side of the hinges and fasten it with the two type B
screws.
- Insert the rubber plug into the bottom hole. The
panel is now ready to be mounted onto the
machine.
Mounting the Panel into the machine.
Insert the nib of the hinge (indicated by the arrow
in ) into the hole for the hinge and push the
panel towards the front of the machine. Fasten
the two hinges with the type D screws.
Fastening the plinth guide.
If the machine is installed at the end of a set of
modular cabinets, mount either one or both of the
guides for the base molding (as shown in ).
Adjust them for depth based on the position of
the base molding, and, if necessary, fasten the
base to the guides .
This is how to assemble the plinth guide :
Fasten angle P using screw R, insert plinth guide Q
into the special slot and once it is in the desired
position, lock it in place using angle P and screw R.
Inserting the machine into the Cabinet.
- Push the machine into the opening, aligning it
with the cabinets .
- Regulate the adjustable feet to raise the machine
to the appropriate height.
- To adjust the position of the wooden panel in
both the vertical and horizontal directions, use the
C and D screws, as shown in .
Important: close the lower part of the appliance front
Fig. 8 Fig. 9
Accessories provided for the height adjustment.
The following can be found
inside the polystyrene lid
10): 2 crossbars (G), 1 strip
(M)
The following can be found
inside the appliance drum:
4 additional feet (H),
4 screws (I),
4 screws (R),
4 nuts (L),
2 plinth guides (Q)
Adjusting the appliance height.
The height of the appliance can be adjusted (from
815 mm to 835 mm), by turning the 4 feet.
Should you require the appliance to be placed
higher than the above height, you need to use the
following accessories to raise it to up to 870 mm:
the two crossbars (G); the 4 feet (H); the 4 screws
(I); the 4 nuts (L) then perform the following
operations :
remove the 4 original feet, place a crossbar G at
the front of the appliance, fastening it in place
using screws I (screwing them in where the original
feet were) then insert the new feet H.
Repeat the same operation at the back of the
appliance.
Now adjust feet H to raise or lower the appliance
from 835 mm to 870 mm.
Once you have reached the desired height, lock
nuts L onto crossbar G.
To adjust the appliance to a height between 870
mm and 900 mm, you need to mount strip M,
adjusting feet H to the required height.
Insert the strip as follows:
loosen the three screws N situated at the front of
the Top cover of the appliance, insert strip M as
shown in , then fasten screws N.
D
C
C
Fig. 6 Fig. 7
LI
H
G
M
Fig. 11 Fig. 12
570
min
518
545
595
009 ÷ 028
600 min
Fig. 10
11338878
18
索引
使用說明
18
控制面板 20
程序表 20
產品介紹 20
洗衣劑盒 20
洗衣程序 21
首次使用 21
日常使用 21
暫停程序 21
打開機門 (如有需要) 21
變更正在運行的程序 21
結束程序 22
選項 22
兒童安全鎖 22
提示及應用 22
保養和維護 22
衣物平衡系統 22
故障排除 23
清潔和保養 24
清潔洗衣乾衣機的外部 24
檢查進水喉 24
清潔進水喉內的濾網 24
清潔洗衣劑盒 25
清潔濾網/排走積水 25
繁體中文
產品安全指引、使用說明及安裝指南
感謝您購買惠而浦產品
為了獲得更完善的服務，
請於www.whirlpool.com.hk註冊您的產品
19
CH
搬運和處理 26
售後服務 26
安全指引 27
安裝指南 29
20
控制面板
程序表
1. 預洗用洗衣劑 (洗衣粉)
2. 主洗用洗衣劑 (洗衣粉或洗衣劑)
3. 添加劑 (如: 衣物柔順劑)
添加劑只能添加到“MAX”標誌。
洗衣劑盒產品介紹
! 白色棉質衣物：請使用洗衣粉，並進行預洗
過程，以及在超過60°C的溫度下進行清洗。
! 請按照洗衣劑包裝上的說明進行操作。
1. 頂板
2. 洗衣劑盒
3. 控制面板
4. 機門門把
5. 機門
6. 底座
7. 可調機腳(4)
1. 電源「開/關」鍵
2.「程序」旋鈕
3.「啟動/暫停」鍵
4.「溫度」鍵
5.「蒸氣抗菌+」鍵
6.「乾衣」鍵 /「兒童安全鎖」鍵
7.「乾衣選項」鍵
8. 顯示屏
9.「預校開機時間」鍵
10.「脫水轉速」鍵
顯示屏指示燈
洗衣階段指示
該指示顯示當前的洗衣階段
乾衣階段指示
「蒸氣抗菌+」啟動
「兒童安全鎖」啟動
獨立乾衣
「乾衣時間模式」
「乾衣選項」
「預校開機時間」啟動
「開門提示燈」
能源標籤測試程序
1)
符合標準EN50229(洗衣)測試程序：使用60°C的 「 棉質節能洗」 程序。
2) 較長的棉質程序：使用40°C的 「棉質」程序。
3) 合成纖維程序：設定「合成纖維」 的洗衣程序溫度為40°C。
符合標準EN50229(乾衣)測試程序：「棉質節能洗」 程序，及設定一
般乾衣程度“ ”。首次負載會根據額定的負載量進行。
若使用溫度高於50°C的程序，建議使用洗衣粉，並按照洗衣粉包裝的指示使用。
* 選擇脫水及排水 程序並設定「脫水轉速」為「0」以進行免旋排水。
在顯示器上或說明書中的程序時間是以標準的情況下計算，實際程序時
間會因不同的因素自動調整，如進水溫度和水壓，環境溫度，洗衣劑
量，衣物的類型，負載平衡及附加選項等。
第6感智能感應 - 智能感測調控技術可通過水流，節能和負載量而調節程
序時間。
使用洗衣乾衣機前請先細閱產品安全指引。
在使用洗衣乾衣機之前，必須卸下搬運螺栓。有關如何移除它們，
更詳細說明，請參閱「安裝指南」。
21 9
3
4
10 6
5
7
8
最大負載量7公斤
程序
需要使用洗衣劑 選擇性使用洗衣劑
最高脫水
轉速 (轉/
分鐘)
60分鐘混合洗
棉質 (2)
合成纖維 (3)
30分鐘速洗
運動衣物
45分鐘極速洗乾
90分鐘混合洗乾
脫水及排水 *
過水及脫水
白色衣物
棉質節能洗 (1)
羊毛 / 手洗
纖細衣物
護色15°
- 40°C
- 60°C
- 60°C
- 30°C
- 40°C
30°C
30°C
-
-
- 90°C
- 60°C
- 40°C
- 30°C
15°C
1000
1400
1200
800
600
1400
1200
1400
1400
1400
1400
800
0
1000
4.5
7
4.5
3.5
4
1
2
7
7
7
7
2
1
4.5
最大
洗衣量
(公斤)
4.5
5
4.5
-
4
1
2
5
5
5
5
2
1
4.5
最大
乾衣量
(公斤)
1:00
3:50
3:15
0:30
1:30
0:45
1:30
0:10
0:50
2:50
2:55
1:15
1:20
1:30
預設洗衣
程序時間
(小時:分鐘)
乾衣
功能
溫度°C
洗衣劑和添加劑 建議洗衣劑類別
-
-
-
洗衣液
-
-
-
-
-
-
-
-
-
-
洗衣粉
柔順劑
3
--
-
主洗
2
預洗
-
-
-
-
-
-
-
-
-
(90°)
-
-
-
-
1
蒸氣
抗菌+
-
-
-
-
-
-
獨立
乾衣
-
-
-
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
