THE FINEST RADIO CONTROL MODELS
R
*Specifications are subject to change without prior notice!
Before beginning assembly, please read these instructions thoroughly.
© Copyright 2010 KYOSHO CORPORATION /
30280-T01
Instruction Manual
Safety Precautions
Content
Equipments not included
Glossary of Main Parts
Before Operating
Let's Drive!
Operating Tips
Replacement for each part
Exploded View
Spare Parts
Trouble Shooting
/ Index
3~7
8
9
10
11~13
14~29
30~31
32~37
38~39
40~41
38
42
43
MINI-Z OVERLAND MV-01 Chassis Set ASF 2.4GHz
2
http://www.kyosho.com/mini-z-support/
Thank you for purchasing this product. This series uses the latest 2.4 GHz ASF system. The increased
processing speed of the RA-18M receiver amp unit delivers significantly faster response and the use of
high-efficiency FET contributes to sharp acceleration. For maximum enjoyment of this product,
please read this manual. A wide range of MINI-Z optional parts are available.
Please refer to the website below for the option parts list.
About This Model
ページを読み込んでいます...
4
As the product includes small and sharp parts, assemble and
store this product only in places out of the reach of children.
Never disassemble the polarity required for installation.
This may lead to damage and leakage.
Cutters, wire cutter and screwdrivers need careful handling.
As the front end of the antenna may be dangerous,
do not swing or aim it toward faces.
Do not store this model in a high-temperature or humid area nor
under direct sunlight.
1
Safety Precautions
5
Do not operate the model on public roads, in crowded places
and near children. It may cause accidents.
Even when the power on the MINI-Z model is switched OFF, there is
still a low current flowing. In order to turn the power OFF completely,
all batteries must be removed from the model. If batteries are left
in the model, the batteries may overheat, ignite or leak.
Please remove all batteries after use.
Always turn power switch OFF and remove batteries when
removing
the body. Touching the circuit board and battery
terminals is dangerous.
Do not touch moving gears. They can cause injury.
1
6
During and after operation, the motor and batteries will be hot.
Do not touch them until they have had time to cool down.
Do not run your car in sandy, dusty, wet conditions, or on thick/soft
carpet. Such surfaces can damage its operating parts.
Do not use water, alcohol, or thinner to clean your car's body.
Simply wipe it down with a clean, soft cloth.
Do not install any option parts not made by Kyosho for this model.
To avoid causing irreparable damage, do not attempt any modifications.
Option Parts
1
Safety Precautions
Thinner
Alcohol
ページを読み込んでいます...
8
*
*Chassis
Content
2
*Pinion Gear Set
(for replacement)
*Motor Spacer
*C-ring (Spare)
*Wheel Wrench
*Battery Holder
* *
*
*Pinion Tool
*
*Front Shock Stay *Rear Shock Stay (2-type)
*
*Deff.Lock Plate
*
*Wheel Nut (Spare)
*
*
*
*
*Pairing Stick
9
*PERFEX KT-18 Transmitter
(Controller)
*PERFEX KT-18
*Or, 2.4GHz ASF compatible transmitter
from Kyosho / Kondo Science Inc.
*
2.4GHz ASF
Equipments not included
*A Phillips Screwdriver (Precision type or a small sized)
*Wire Cutter
*Cutter
*
*
*
+ +
*4-AAA sized Alkaline Batteries or UM-4 sized
NiMH (Nickel-Metal Hydride) Batteries 4 pieces
Do not use any damaged batteries.
*4
4 4
*AAA sized or UM-4 sized Alkaline Batteries
*4
Damaged
Do not use Oxyride or other special type batteries.
*Body Set (Auto Scale Collection)
*
AAA
UM-4
4
3
10
Glossary of Main Parts
4
Chassis
Front Tire
Antenna
Pairing Button
Rear Tire
Rear Shock Unit
Front Shock Unit
Power Unit
Motor
Power Switch
Battery Holder
LED Indicator
I.C.S. Connector
ページを読み込んでいます...
12
Before Operating
5
2x10mm
2x10mm
2x6mm
2x6mm
2x6mm
*Replace shock stays in accordance with the suspension shaft positions.
*
6
2 x 6mm
TP Screw
TP
4
2 x 10mm
TP Screw
TP
Front Rear
Suspension Shaft
Suspension Shaft
4.8mm
Pillow Ball
4.8mm
Pillow Ball
C-ring
C
C-ring
C
Front Shock Stay Rear Shock Stay
Plastic Pencil Tip C-ring
C
Suspension Shaft
Adjustment of Wheelbase
Wheels and tires included with this set can be used with any body set.
If using the wheels and tires included with the body set, refer to the section 'Tires' in '8 Replacing Each Part'
and install accordingly.
13
Battery Installation
5
Battery Holder
AAA Batteries, Notice the polarity to be installed.
Battery Holder
4
To remove Battery Holder. To attach Battery Holder.
If it is not easy to remove the battery
holder, try with a flat blade screwdriver.
For installation of transmitter batteries, please refer to your transmitter's instruction manual.
14
Instructions from this point onwards relate to use with the PERFEX KT-18 transmitter.
If using a different transmitter, refer to the instructions included with your transmitter.
To use this transmitter with a previously purchased chassis (MINI-Z OVERLAND), it must undergo a pairing
adjustment.
Antenna
Pairing is the process of registering the transmitter's ID with your chassis. If you change transmitters, please
perform pairing. Pairing process is not required after the first time.
What is pairing?
< >How to complete pairing
Let's Drive!
6
Turn the Power Switch ON
15
1
1
LED Indicator
Push the mark side of the Throttle Trim and keep it down.
2
2
Push the power button to switch the transmitter ON.
Keep the mark pressed down, but release power button.
4
Once the LED indicator light has dimmed, the preparation of the transmitter is complete.
3
3
Confirm the LED is on. When the LED goes out after about 3 seconds, release finger from the Throttle Trim.
Pairing Button
6
Prepare pairing stick and locate the
LED indicator and pairing button.
Pairing Stick
OFFON
OFFON
16
1
2
Chassis (Switch)
Use the pairing stick to push and hold
the pairing button.
5
Chassis (Switch)
4
3
Once the LED indicator comes on, stop pushing
the Pairing Button.
LED Indicator will show the following.
Light is ON : Pairing has been successful
Light is flashing : Pairing has not be completed.
Switch the transmitter and chassis
power off and do pairing again.
Let's Drive!
6
LED Indicator
17
6
Push the transmitter power button again and to turn it off.
Setting takes effect the next time power is turned on.
In rare cases, the pairing data may be lost. This is not
a malfunction. Simply repeat the pairing process.
If Pairing Failed
6
Someone else close by is pairing at the same time. Complete pairing at another time.
Another 2.4GHz device is being used close by. Stop using wireless LAN or Bluetooth devices.
Appliances such as a microwave oven are emitting
strong electrical waves are being used close by.
Stop using the electrical appliance.
Another radio control model using 2.4GHz is being used
close by.
Perform pairing in another location.
Attaching the Body.
Carefully spread the sides
of the body over the chassis
mounts.
2
1
1
2
OFFON
18
Antenna
Always turn the transmitter's power switch ON first!
Keep hands away from tires!
1
Push the power button to turn transmitter on.
2
Check that the LED indicator lights up.
Chassis (Switch)
When switched on, the transmitter finds open frequencies. Up to forty 2.4GHz Mini-Z Series models can be run
but may be lower if other 2.4GHz devices are being used. If no frequency can be found, LED will not light.
Operate in another location.
NOTE
< >For Normal Operation
1
2
Wheels may spin freely when power is turned on.
Let's Drive!
6
19
Throttle Trigger
Throttle Trim
Neutral
Raise the tires off the ground and check that all controls are responding.
With throttle trigger in neutral, click Throttle Trim one click at a time until car stops and continuous beep stops.
Adjustment not needed if car doesn't move. Beeping sound will start when neutral is found or range limit is reached.
If chassis is moving in reverse, click this button.
A
A
B
If chassis is moving forward, click this button.
B
Bringing the Car to a Complete Stop
Forward Reverse
6
20
Left
Right
Right
Left
Neutral
Left Right
Steering Wheel
How to Control Your Model.
Basic Controls
Raise the tires off the ground and check
hat all controls are responding.
Throttle Trigger
Forward
Neutral
Reverse
Brake
Raise the tires off the ground and check that all controls are responding.
Forward Reverse
Let's Drive!
6
21
Reversing Point
Forward
Brake
Neutral
Reverse
6
22
Click Throttle Trim a few times until
tires move forward.
2
A
A
Click Throttle Trim a few times until tires
stop. Then click a few more times until beep
sound stops.
3
B
B
Click Throttle Trim 8 more times.
Adjustment is complete.
4
B
B
Check if a continuous beep sound is coming from the chassis.
If no sound Refer .
Problems with Reversing?
When Throttle Trigger is in neutral and the car hasn't stopped moving, follow the steps below to adjust neutral position.
1
2
2
Refer .
2
2
Refer .
3
Refer .
3
3
Refer .
4
4
Beep sound but car is moving forward.
Beep sound but car is moving backwards.
Throttle Trim
A
B
3
Let's Drive!
6
23
Steering Wheel Steering Trim
Neutral
With steering wheel in neutral, click the Steering Trim a few times so car runs in a straight line.
Use one click at a time. (Holding the button down does not work.)
If chassis moves left (L), click Steering Trim to adjust.
R
L R
RL
If chassis moves right (R), click Steering Trim to adjust.
R
L
L
When steering trim is in neutral or adjustment has reached the end of its range, beeping sound will start.
Due to effects from steering mechanism or surface, the car may not run perfectly straight. This is not abnormal.
L R
Running in a Straight Line
6
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/