Shure Bluetooth Earphones RMCE-BT2 ユーザーマニュアル

  • Shure RMCE BT2 Bluetoothイヤホンのクイックスタートガイドの内容を理解しています。ペアリング、充電、リモートコントロール操作など、このデバイスに関するご質問にお答えできます。快適な装着感と高音質サウンド、便利な機能を備えたイヤホンに関する疑問点があれば、お気軽にご質問ください。
  • イヤホンのペアリング方法は?
    バッテリー残量を確認するには?
    イヤホンを充電するには?
    イヤーチップの交換方法は?
    音量を調整するには?
RMCE-BT2
Shure Bluetooth Earphones
®
The Shure Bluetooth earphones, BT2, quick start guide.
Version: 7.0 (2020-L)
Shure Incorporated
2/9
Table of Contents
RMCE-BT2 Shure Bluetooth® Earphones 3
Bluetooth Pairing 3
The best sound starts with a good fit 3
To keep them sounding their best... 3
Changing Sleeves 4
Using the Remote 4
The Center Button 4
Up and Down Buttons 4
Charging the Earphones 4
Specifications 5
5
Safety Information 5
WARNING 5
Information to the user 6
Certifications 7
Shure Incorporated
3/9
1.
2.
3.
RMCE-BT2
Shure Bluetooth Earphones
Bluetooth Pairing
Turn off the earphones. Press and hold the center button on the earphone remote until the LED flashes blue and red.
From your audio source, select "Shure BT2."
When successfully paired, the LED turns blue.
Note: If the pairing fails on the first attempt, repeat the process from the beginning.
For additional pairing methods, please visit http://www.shure.com/earphones.
The best sound starts with a good fit
Select the sleeve that provides a snug fit (like earplugs).
Secure the cable behind the ear to maintain a tight seal.
To keep them sounding their best...
Clean regularly to remove debris and deposits.
ContactShureServiceandRepairtoreplacedamagedproduct.Simplydetachandreturnthebrokenearpieceforeasyre
placement.
®
Shure Incorporated
4/9
Changing Sleeves
Gently twist and pull to remove sleeve.
Install the new sleeve so it completely covers the barb and nozzle.
Visit http://www.shure.com/earphones for replacement parts and important instructions on cleaning and maintenance.
Using the Remote
The Center Button
Power on Press and hold
Power off Press and hold, 5 seconds
Pair Bluetooth Turn off the earphones. Press and hold, 7 seconds
Play/Pause Click once
Answer/End a call Click once
Decline a call Press and hold, 3 seconds
Activate voice assistant Phone on, press and hold, 3 seconds
Factory Reset
Turn off the earphones and plug into a charger. Press
andhold,15seconds.Holdpastpairingmodeuntilear
phones turn off again.
Up and Down Buttons
Volume Up/Down Click + or -
Next track Press and hold +, 3 seconds
Previous track Press and hold -, 3 seconds
Check battery status Press and hold + and - together, 3 seconds
Your phone may not be compatible with some functions. Visit http://www.shure.com/earphones for more information.
Shure Incorporated
5/9
1.
2.
3.
Charging the Earphones
Red LED indicates low battery.
Connect the earphones to a charging device using the supplied USB cable.
The LED is red while charging.
When fully charged, the LED turns off.
Warning: Before charging, make sure the product is at room temperature, between 10 to 45°C (50 to 113°F).
Note: Use this product only with an agency approved power supply which meets local regulatory requirements (e.g., UL, CSA, VDE, CCC, INMETRO).
Specifications
Antenna Information:
Type = Chip
Gain = +1.6 dBi
Bluetooth 5:
Operating frequency = 2402MHz-2480MHz
Modulation scheme = FHSS
RF power = +7.45dBm (E.I.R.P.) (for EU)
Supported Codecs:
aptX
aptX HD
aptX Low Latency
SBC
AAC
Safety Information
WARNING
Follow instructions from manufacturer.
Product battery may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble,
heat above 140°F (60°C), or incinerate.
Attention should be drawn to the environmental aspects of battery disposal.
Product shall not be exposed to excessive heat such as sunshine, fire, or the like.
Shure Incorporated
6/9
1.
2.
1.
2.
1.
2.
Do NOT make unauthorized alterations to this product.
Note: Battery replacement to be performed only by Shure authorized service personnel.
CAUTION: Follow applicable laws regarding mobile phone and headphone use while driving.
This product contains magnetic material. Consult your physician on whether this might affect your implantable medical device.
High sound pressure
Hearing damage risk
To prevent possible hearing damage, do not listen at high volume levels for long periods.
Information to the user
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
theFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstalla
tion. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.
Cetéquipementestconformeauxlimitesd'expositionauxradiationsICCNR102établiespourunenvironnementnoncon
trôlé. Cet émetteur ne doit pas être situé au même endroit ou fonctionner avec une autre antenne ou un autre émetteur.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
根據NCC低功率電波輻射性電機管理辦法 規定:
第十二條 經型式認證合格之低功率射頻電機非經許可公司商號或使用者均不得擅自變更頻率加大功率或變更原
設計之特性及功能
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信經發現有干擾現象時應立即停用並改善至無干
擾時方得繼續使用 前項合法通信指依電信法規定作業之無線電通信 低功率射頻電機須忍受合法通信或工業科學
及醫療用電波輻射性電機設備之干擾
經審驗合格之射頻電信終端設備非經許可公司商號或使用者均不得擅自變更頻率加大功率或變更原設計之特性及
功能
射頻電信終端設備之使用不得影響飛航安全及干擾合法通信經發現有干擾現象時應立即停用並改善至無干擾時方得
繼續使用所謂合法通信係指依電信法規定作業之無線電信
Shure Incorporated
7/9
3.
4.
1.
2.
3.
輸入製造射頻電信終端設備之公司商號或其使用者違反本辦法規定擅自使用或變更無線電頻率電功率者除依電
信法規定處罰外國家通訊傳播委員會並得撤銷其審驗合格證明
減少電磁波影響請妥適使用
Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan y para una ganancia máxima de antena
de [+1.6] dBi. El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que [+1.6] dBi
quedan prohibidas. La impedancia requerida de la antena es de [50] ohms.
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no
cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda
causar su operación no deseada.
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The
disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the
appliancestothesecollectingpointsortosimilarcollectionpoints.Withthislittlepersonaleffort,youcontributetorecyclevalu
able raw materials and the treatment of toxic substances.
Certifications
Visit http://www.shure.com/earphones for the latest regulatory and compliance information.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
Note: Testingisbasedontheuseofsuppliedandrecommendedcabletypes.Theuseofotherthanshielded(screened)cabletypesmaydegradeEMCper
formance.
电池电池包或组合电池不得暴露在诸如日照火烤或类似过热环境中
根据当地法规处理废弃电池
運用しての注意
この機器使用周波数帯では、電子レンジ産業科学医療用機器のほか工場製造ライン使用されている移動体識別用
構内無線局免許する無線局特定小電力無線局免許しない無線局びにアマチュア無線局免許する
線局)が運用されています。
この機器使用するに、くで移動体識別用構内無線局及特定小電力無線局並びにアマ   チュア無線局運用
れていないことを確認してさい。
万一、この機器から移動体識別用構内無線局して有害電波干渉事例発生した場合には、 やかに使用周波
変更するか電波発射停止した下記連絡先にご連絡頂き、混  信回避のための処置等えば、パーティ
ションの設置など)についてご相談してさい。
その、この機器から移動体識別用特定小電力無線局あるいはアマチュア無線局して有害電波干渉事例発生
した場合などかおりのことがきたときは、保証書記載販売代  理店または購入店へおわせください。
理店および販売店情報 Shure 日本語ウェブサイト  http://www.shure.co.jp でもごいただけます。
Shure Incorporated
8/9
現品表示記号について
現品表示記号は、以下のことをしています。 この無線機器 2.4GHz 電波使用し、変調方式は「FH-SS方式想定与干
渉距離 10m です。 2,400MHz2,483.5MHz 全帯域使用し、移動体識別装置帯域回避することはできません。
日本電波法および電気通信事業法準拠デバイスは日本電波法および電気通信事業法づく認証けています。
バイスを改造しないでください(改造すると認証番号無効になります)。
Esteequipamentonãotemdireitoàproteçãocontrainterferênciaprejudicialenãopodecausarinterferênciaemsistemasdev
idamente autorizados.
адаптерыSecureFit
производитель:SHURE
модельRMCETW1
Декларант:Обществосограниченнойответственностью«ШурАрИИ»
Юридическийадрес:119049,Москва,4ыйДобрынинскийпер.,д.8,офис114.
Фактическийадрес:119049,Москва,4ыйДобрынинскийпер.,д.8,помещение114,офисR01211
Телефон:+7(985)4337253
Факс:
ОГРН:1147746623573
зарегистрировано:03июня2014
влице:Генеральногодиректора
ФИО:ЭрнфельтАнгелика
Напряжениепитания:
Зарядныйкейс:Input:5V0.26A
Наушники:Input:5.1V0.042A
Диапазончастот:2402MHz–2480MHz
Вес:20.8g
СделановКитае
Датаизготовленияуказананапродукте
이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서 가정용 환경에서 사용하는 경우 전파간섭의 우려가 있습니
.
Paraguay Distributor: Microsystems S.R.L., Senador Long 664 c/Dr. Lilio, Asunción, Paraguay
Hereby, Shure Incorporated declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet address: http://www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Shure Incorporated
9/9
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4
The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by
Shure Incorporated is under license. Other trademarks and trade names are those of their respective owners.
Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. aptX is a trademark
of Qualcomm Technologies International, Ltd., registered in the United States and other countries.
®
/