HD Video Capture

Quick Start Guide

Thanks for purchasing ezcap280H HD Video Capture. The following guides you how to set up the

device. Hope this device will bring you nice digital experience.

With this ezcap280H HD Video Capture, you can capture 1080P video from HDMI port, such as blue

ray, set-top-box, computer, game box, etc.

2. INPUT—HDMI input.

3. PWR—DC 5V power supply.

4. USB HOST—For plug USB flash drive or USB

HDD for saving record files.

5. LED indicator—Color be green when standby, be

red when recording.

How to play:

1, Connect power with DC adaptor

2, Use HDMI cable connect Xbox or other source.

3, With HDMI cable connect to monitor

4, Plug an USB disk on.

green.

Most important: Use “safety remove”

option to remove your USB flash or HDD after

format from computer, DO NOT just plug out without click “safety remove” option, otherwise you will

cause problem during recording.

The recording will be stopped automatically if the USB memory is full, or the input video signal is lost

during recording.

Every record/stop operation will create a different recording file: Encode_1080P_1, Encode_1080P_2,

Encode_1080P_3… and so on.

The max size per file will be around 1.95GB (around 17 minutes for 1080p video), when you record a

video more than 1.95GB(15 minutes), ezcap280 will partition it in more than 1 file, for example: if you

record a 45 minutes 1080p video by one click recording, you will see 3 files: Encode_1080P_1,

Encode_1080P_1_1, Encode_1080P_1_2…and so on

If you like use a media player to playback the recorded video, make sure it support MPEG4 video

8, Reset: After long time using, you will see the number of recording file become too big, for example

Encode_1080P_234, but you want it be start from Encode_1080P_0, to do it you just keep press

record button (before power on), then plug the power jack to power on the device, after 3 seconds,

the file number will start from 0.

Edit/Convert recorded files:

The ezcap280H comes with a video edit software—Arcsoft ShowBiz 3.5, you can edit your video file

with it.

1, You can combine two or more video in one, just drag them into Showbiz:

4, Please click “Create file” to create multiple files for different devices, such as apple, PSP, mobile

phone, etc:

高清视频采集盒

ezcap280H 高清视频采集盒支持从 HDMI采集 1080P 高清视频。产品采用一键录制设计，操作简单。

外观、按键及接口

1. OUTPUT—HDMI视频输出，用于实时显示从 HDMI

4. USB HOST—用于插入 U 盘或 USB 硬盘盒以存储录

制内容

5. LED 指示灯—状态指示。绿色为待机状态，红色为录

制状态。

6. MIC—麦克风输入.

2, 使用 HDMI线材连接视频源 HDMI输出到高清视频

采集盒的 HDMI IN 接口。

3, 使用HDMI线材连接高清视频采集盒的 HDMI OUT

接口到电视机或显示屏的 HDMI输入接口。

4, 插入 U 盘或移动硬盘

5, 如果你需要同时录制你的语音，请连接麦克风到

MIC 接口。

注意：如果按下录制键，指示灯没有变化的话，或许

有如下几种原因，请确认：

1, 输入的视频源没有连接好

2, U 盘或移动硬盘容量已满

3, U 盘、移动硬盘的格式不适合，比如 exFAT 格式。 采集盒支持 FAT、FAT32 和 NTFS 格式。

4, U 盘、移动硬盘没有插好

注意：当 LED 指示灯闪烁时， 请不要拔下 U 盘，否则有可能会丢失部分录制文件。如果 U 盘录制满，

采集盒会自动停止录制，不会损坏或丢失之前的录制文件。

将存有录制文件的 U 盘或移动硬盘与电脑连接，你将会看到视频录制文件： 1080P 的录制文件，文件

名为 Encode_1080P_1， 720 或 480 录制文件为 Encode_1。

每一次 录制/停止的操作，伊卡普采集盒都会新建一个不同的录制文件：Encode_1080P_1、

Encode_1080P_2、Encode_1080P_3…

每一个文件最大约为 1.95GB (1080p 视频文件约 17分钟)， 当你录制视频超过 1.95GB，采集盒会自

存储设备格式为 FAT32 格式并再次尝试。

程序升级、文件名清零和文件时间设定:

1, 程序升级：因为一些原因你或许需要升级程序。 请将新的程序拷贝到 U 盘内，将采集盒电源拔掉，

插上 U 盘，再接上电源，这时指示灯将会闪烁七八秒， 并最终变成绿色常亮，这时表示软件升级成功。

本录像盒配送了一个强大的视频编辑软件—Arcsoft ShowBiz 3.5, 您可以使用它来编辑您所录制的视

频。 按照提示安装好软件后打开：

1, 将需要编辑的视频拖入编辑框，比如将两段视频拖入合并为一个视频文件:

2, 也可以把一段视频分割为两段: