FIC EUN-R02501 ユーザーマニュアル

ブランド: FIC

モデル: EUN-R02501

タイプ: ユーザーマニュアル

このマニュアルも適しています

Maat

FIC Maat user manual V4.0

CHAPTER 1 HARDWARE INSTALLATION .....................................................................................4

1.1 HARDWARE SPECIFICATION: ..........................................................................................................4

1.2 HARDWARE INSTALLATION..............................................................................................................5

1.3 CLIENT PC CONFIGURATION..........................................................................................................7

1.4 FORMAT STORAGE ......................................................................................................................8

CHAPTER 2 QUICK SETUP..............................................................................................................10

2.1 MAIN MENU SETUP ......................................................................................................................10

2.2 STEPS OF QUICK SETUP...............................................................................................................11

CHAPTER 3 NETWORK INTERFACE ............................................................................................16

CHAPTER 4 SYSTEM CONFIGURATION......................................................................................20

4.1 SHUTDOWN AND REBOOT ............................................................................................................20

4.1.1 Shutdown.............................................................................................................................20

4.1.2 Reboot..................................................................................................................................21

4.2 LOAD DEFAULTS ...........................................................................................................................21

4.3 SYSTEM NTPTIME/DATE / TIMEZONE...........................................................................................22

4.3.1 System NTPtime/date........................................................................................................22

4.3.2 System Timezone...............................................................................................................22

4.4 EVENT NOTIFY..............................................................................................................................22

4.5 UPGRADE......................................................................................................................................23

4.6 SYSTEM LANGUAGE .....................................................................................................................23

4.7 S

AVE SYSTEM CONFIGURE FILE...................................................................................................24

4.8 SYSTEM LOGGING ........................................................................................................................24

CHAPTER 5 ACCOUNT MANAGEMENT.......................................................................................26

5.1 ADD ACCOUNTS............................................................................................................................28

5.1.1 Create Single-user Accounts:...........................................................................................28

5.1.2 Create Multi-user Accounts by Serial Number...............................................................29

5.2 ADD ACCOUNTS IN BATCH ............................................................................................................30

5.3 ACCOUNT QUERY .........................................................................................................................32

5.3.1 Query....................................................................................................................................32

5.3.2 Hidden..................................................................................................................................33

5.3.3 Modify & Delete Single User.............................................................................................34

5.3.4 Modify & Delete Multiple Users........................................................................................35

5.4 DEFAULTS FOR ACCOUNT.............................................................................................................36

5.5 CHANGE ADMIN USER PASSWORD ..............................................................................................36

5.6 ACCOUNT VERIFICATION...............................................................................................................37

5.7 USER LOG LOGGING ....................................................................................................................37

CHAPTER 6 SERVICE.......................................................................................................................38

6.1 ADMINTOOL...................................................................................................................................38

6.1.1 Configuration:......................................................................................................................39

6.1.2 Firewall Configure:.............................................................................................................39

6.2 WEB CACHE .................................................................................................................................40

6.2.1 Steps of Cache Configuration...........................................................................................40

6.2.2 Enable Transparent Mode.................................................................................................41

6.2.3 Client-end Browser Configuration (Microsoft Windows Client)...................................43

6.2.4 Cache Peer ..................................................................................... !

6.2.5 Multi Router Traffic Grapher (MRTG).......................................... !

6.2.6 Cache Management....................................................................... !

6.3 DHCP SERVICE ....................................................................................... !

6.3.1 Steps of DHCP Configuration....................................................... !

6.3.2 DHCP Client-End Configuration................................................... !

6.3.3 DHCP Logging................................................................................ !

6.4 DNS ......................................................................................................... !

6.4.1 Configurations................................................................................. !

6.5 FTP .......................................................................................................... !

6.5.1 Steps of FTP Configuration........................................................... !

6.5.2 Anonymous Configuration............................................................. !

6.6 MAIL.......................................................................................................... !

6.6.1 Mail Configuration .......................................................................... !

6.6.2 Mail Alias.......................................................................................... !

6.6.3 Mail Access List Configuration..................................................... !

6.6.4 Configure Mail Domain for Localhost.......................................... !

6.6.5 Configure Email-Relay Domain.................................................... !

6.6.6 Configure Group Mail Domain...................................................... !

6.6.7 Mail Queue...................................................................................... !

6.6.8 Mail Logging(SendMail)................................................................. !

6.6.9 Mail Logging(Simple)..................................................................... !

6.6.10 Mail for root & sysop Managers................................................. !

6.6.11 Mail Tools....................................................................................... !

6.7 MRTG (MULTI ROUTER TRAFFIC GRAPHER) TRAFFIC MONITORING..... !

6.7.1 MRTG Configuration...................................................................... !

6.7.2 MRTG Logging................................................................................ !

6.8 NAT.......................................................................................................... !

6.8.1 Configuration................................................................................... !

6.8.2 Port Redirection.............................................................................. !

6.8.3 NAT Logging.................................................................................... !

6.9 NETBIOS SERVICES ................................................................................. !

6.9.1 NetBios Configuration.................................................................... !

6.9.2 Volume Management..................................................................... !

6.9.3 Connection ...................................................................................... !

6.9.4 NetBios Logging............................................................................. !

6.10 POSTGRESQL........................................................................................ !

6.10.1 Database Admin........................................................................... !

6.10.2 Server Access Admin................................................................... !

6.11 MYSQL................................................................................................... !

6.12 SSH ....................................................................................................... !

6.12.1 SSH Configuration....................................................................... !

6.13 TELNET ................................................................................................ !

6.13.1 TELNET Configuration................................................................ !

6.14 WEB MAIL............................................................................................... !

6.14.1 Operation Procedure to enter Open WebMail......................... !

6.14.2 User Preferences......................................................................... !

6.14.3 Compose Message...................................................................... !

6.14.4 Check Mails................................................................................... !

6.14.5 Delete Mails .................................................................................. !

6.14.6 Address Book................................................................................ !

6.14.7 Web Mail Configure..................................................................... !

6.14.8 Web Mail Logging ........................................................................ !

6.15 WEB SERVICE ........................................................................................ !

6.15.1 Web Port Configure..................................................................... !

6.15.2 Web Service Logging .................................................................. !

6.15.3 Place Homepage.......................................................................... !

CHAPTER 7 FIREWALL ................................................................................ !

7.1 A

LLOW PORT CONFIGURE........................................................................ !

7.2 DENY IP CONFIGURE ............................................................................... !

CHAPTER 8 TIMEFINDER ............................................................................ !

8.1 B

ACKUP TO HOST..................................................................................... !

8.2 BACKUP AND DOWNLOAD......................................................................... !

8.3 TIMEFINDER FROM HOST.......................................................................... !

8.4 TIMEFINDER FROM BROWSER .................................................................. !

CHAPTER 9 ONLINE HELP.......................................................................... !

FCC NOTE……………………………………………………………………………………………89

Chapter 1 Hardware Installation

1.1 Hardware Specification:

Dimension 246 mm * 56 mm * 240 mm

CPU Transmeta Crusoe TM5600 500MHz

Memory

One 144 pin SODIMM slot, can support SDRAM 64 / 128 / 256 /

512MB

Storage

2.5 “ IDE HDD, support 20/30/40/60GB capacity HDD

CompactFlash™ Memory Card, support 16 / 32 / 64 / 128 /256MB

Module

Network

4 10/100 Fast Ethernet NIC

One 10/100 Mbps Fast Ethernet Up-Link Port

Software Driver for Wireless LAN Card (AP) 802.11b

Power Supply External 60W/12V AC Power Adaptor

LED Display

Power LED

System LED

Ethernet Network LED

WAN LED

Wireless LAN AP LED

Expansion Port

2 USB Port (Support USB 1.1)

1 Parallel Port

1 COM Port/RS-232 DB-9 Port (Console Port)

1 Power Switch/Reset Button

1 AC Power Adaptor Socket

4 Ethernet Port (RJ45)

1 WAN Port (RJ45)

Material of Box

Metal and Plastic Case

Fanless

1.2 Hardware Installation

It’s very simple for the Maat installation. According to the diagram below, please connect

the power source and appropriate cable to the Maat system. You will easily to finish the

hardware installation.

1. Power LED (Green)

It’s to indicate system power status.

2. System LED (Red)

While system in booting process the LED will be quickly blinking. It will turn to be

slowly flash while system in normal operation.

3. Ethernet LED (Yellow)

The Ethernet LED used to indicate the successful connection of Ethernet LAN port.

It will become flash to indicate the transmission of Ethernet packet.

4. WAN LED (Amber)

The WAN LED is used to indicate the successful connection of Ethernet WAN port. It

will become flash to indicate the transmission of Ethernet packet.

5. Wireless AP LED (Blue)

The LED is used to indicate the successful connection of wireless LAN port. It will

become flash to indicate the transmission of wireless LAN packet.

The diagram below is the layout of connector in rear Maat server. Please connect the

power and network cable to finish the Maat server installation.

1. Power Switch (Reset Switch)

It’s the switch for resetting the Maat system. The Maat system will automatic getting

up while you connect the power source.

2. Two USB Port

The Maat server build in two USB ports. It provided “Plug and Play” function for

device connectivity.

3. COM Port (Console Port)

The system equip with an RS-232 (DB-9) console port. It allow system administrator

to connect any terminal or modem device for system configuration or diagnostic

purpose.

4. Parallel Port

The Parallel Port is used to printer or scanner connection.

5. WAN Ethernet Port

The WAN Ethernet Port is dedicated for connecting to WAN network. Please

connect this port to your Internet gateway device.

6. 4 RJ45 Ethernet Port (1 2 3 4)

Maat system equip with four 10/100 fast Ethernet ports. It allows user to connect

their client user or another Ethernet switch device.

7. AC Power Adaptor Socket

Please connect the AC power adaptor cable to this socket.

After you connect the power adaptor to Maat system. The power will automatically

getting up while you connect the power source. The “Power Switch” button is just for

resetting the system.

While system booted up. You will see a login screen. Please Login to the system by

entering “sysop” for User Name and “steptech” for Password as following:

While in system boot process, you can press any key when the message “Hit [Enter] to

boot immediately, ….” is displayed on the screen. System will enter to “OK” prompt.

Here to describe three commands for system recovery function:

1. boot –s: is used to recover the sysop and root’s password to system default as

“steptech” and “no password”. The root’s password will reset to as “none”. For

security reason you are recommended to change their password through the Mail

Tool home page.

2. boot –c: is used to completely reset the system default.

3. boot –d: is used to perform the “fdisk” function. The login prompt will appear after the

“fdisk” process. You can login as “sysop” to continue performing “format” command

process. They will accompany with a melody sound effect while the format process is

in progress.

1.3 Client PC Configuration

Now connect another client PC to Maat server via crossover cable or hub.

Server will configure related settings via the browser. The default value of Maat system

network interfaces is as follows:

IP (public): 172.16.100.1 NetMask: 255.255.0.0

Client PC configurations are very simple, just requiring a few of steps as shown below:

1. Click the right mouse button on the “My Network Places” and select “Properties”.

Then select “TCP / IP”  “NIC”.

2. As shown in the figure below, enter related IP configurations before clicking OK. After

the reboot finishes, start up the browser. If the Proxy configurations are enabled,

disable the configuration. Let’s take IE as an example: Select Tools  Internet

options  Connections  Local Area Network (LAN) configurations  Disable the

“Use a proxy server” option.

3. Enter the URL of http://172.16.100.1:10000/ on the browser.

4. Log on the monitoring interface by entering “sysop” for User Name and “steptech” for

Password.

1.4 FORMAT Storage

If the HD has yet been formatted, a screen will be shown as follows:

In this case, click “Format” to format the HD. Before the format is completed, don’t

disrupt the browser window, or there will be unforeseeable errors. The figure below

shows the status during the formatting.

After the format is completed, a screen will be shown as follows. Since no reboot is required,

you can proceed with Quick Setup or other related configurations.

PS Please don’t use the “fdisk” command on local as you wish lest to clear the partition of

Maat chip.

Chapter 2 Quick Setup

The quick setup of system configurations allows users to complete the basic settings of

system configurations in simple steps and within a short time. The basic settings include the

IP, Netmask, DNS server addresses, Time Zone, system time, Hostname, NetBios settings

(network neighborhood) of the NIC, as well as the applications provided by the system. After

the settings are completed, the basic configuration of the system is also completed – the

system can serve you right now without any trivial settings required.

2.1 Main Menu Setup

panel screen, and then a main menu initially configured by the system will immediately

appear. The screen allows users to configure initial settings before they are able to enter

the browser’s management interface to change settings, so as to facilitate subsequent

connection. In the main menu, what you have to do is set up the HOSTNAME, IP

address, Netmask and Default Router. Then, without the hassle of reboot, you can apply

these settings and enter the browser’s management interface to change other settings.

Start with setting up the IP Address of NIC for the private network here, so that you can

use a nearby browser to configure other settings afterwards.

“6. Reset Admintool password”, the sixth item of the main menu, allows you to restore

the factory default password of “steptech” when you forgot the password “sysop”.

If you had changed some system settings that resulted in the system’s abnormal

operation, select “7. Write Default & Reboot” to conduct certain configurations and

thereby have these settings restore to the factory default settings.

“8. Reboot” means restarting the computer, and “9. Shutdown” turning off the machine.

After you select shutdown, bear in mind that there is no true shutdown without turning off

the host’s power supply. Or you can restart the computer by pressing any key.

The Main Menu is shown as follows:

MAIN MENU

Please select the action you wish to run

1 Exit this menu

2 Hostname host.domain

3 Ip 192.168.2.45

4 Netmsak 255.255.255.0

5 Default Router 192.168.2.254

6 Reset Admintool password

7 Write Default & Reboot

8 Reboot

9 Shutdown

OK Cancel

2.2 Steps of Quick setup

1. Interface:

As shown in the figure below (Realtek 8139-series is taken as an example here), it

automatically displays the name of devices and MAC Address. Enter related

configurations in individual fields, and then click “Submit”.

A window box will then appear, reminding you that client PCs will disconnect after

the change applied.

Change the TCP / IP configurations of client network configuration in accordance

with the IP and Netmask value you configured for the system.

Let’s take the IP / Netmask 192.168.2.45/255.255.255.0 of the system as an

example. The client configurations are shown as follows:

Upon the restart of PC, you can log on the system via the browser and thereby

proceed with other related configurations.

Now select the quick setup option at the left side, and then click “Submit” in the

“Interface”. Since the client and the system locate in the same network segment,

their IP and Netmask are the same, i.e., 192.168.2.46 and 255.255.255.0

respectively.

Then you can head for the completion of other related configurations by following

the subsequent steps of quick setup.

2. Hostname:

Enter the hostname in the Hostname field.

3. Routing Table:

Select Static Route or Routed for the Route Type. If you select Static Route, you can

configure the Default Router in the field below. If there are multiple routes in the

network environment, configure the settings in the fields of “Destination” and

“Gateway” that suit your needs.

4. Nameserver:

For setting up the Nameserver for the system.

5. System Timezone:

For setting up the information on the timezone and country where the system is

located.

6. System NTPtime/date:

For setting up the current time and NTP Server for the system.

7. NetBios Configure:

For configuring the settings so that this server can be seen in the “My Network

Places”.

8. Service:

It is for setting up network services provided by the system. Each service item has

the options of Enable and Disable. If you want to start up a certain service, select

Enable, otherwise select Disable. After completing all of the settings, click “Submit”

to finish the basic configurations for the system. Then the screen will automatically

return to the homepage. For more detailed configurations, please refer to the

following chapters and sections.

Chapter 3 Network Interface

Select “Interface” of “System Management Tools”, and then a figure will appear as follows:

The figure displays current network configurations. If your system is equipped with more

than four Ethernet NICs, the menu will automatically extend and automatically detect the

manufacturers and the NIC types, without the hassle of manually setting up the driver.

Let’s have the description for each network NIC’s utilization:

1. 1st Ethernet NIC – It’s dedicated for connecting to WAN (Internet). For different

network connectivity requirement, there are three network architectures for user to

make desired configuration. Please select a correct architecture depends on your

network environment. The “Device” represents the NIC code identified by the system.

Here r1 stands for Realtek, fxp for Intel. The “Ether” represents MAC Address of the

NIC, that is the code of NIC manufacturers and serial number of the product.

1.1 PPPoE: If you are using ADSL for Internet connectivity. Than you have to enable

the PPPoE option. Please click on “PPPoE Configure”, the configuration table will

show as below. Please enter the authentication user and password information as

provided from ISP.

1.2 DHCP: If user using DHCP to dynamically apply for IP address from ISP. They

must to enable the DHCP function. Please click on “DHCP”, the configuration

table will show as below. You will find the acquired IP Address and Netmask

information in the field.

1.3 Fixed IP Address: You are capable to configure a fixed IP address for this NIC.

You can click on “Use a following IP Address”, the configuration table show as

below. Please enter the IP Address and Netmask information dedicated for this

NIC.

After you make any one of different configuration. Please click on “Submit” to apply

for changes.

2. 2nd Ethernet NIC – represents the NIC for connecting to your LAN network. Please

enter the IP address and Netmask information for the NIC. The Maat system also

equip with four RJ-45 Ethernet port for client user connection.

P.S. Please do NOT connect different network segment’s cable to same Ethernet switch

to avoid unexpected errors.

3. 4th Wireless NIC (Option) - The Maat system is capable to support wireless

connection from any client PC. If your Maat system equipped with wireless NIC, the

item field will automatically extend and automatically detect the manufacturers and

the NIC types, without the hassle of manually setting up the driver. Let’s take the

following wireless NIC as an example to describe how to configure each item.

Wireless AP(Access Point)

Maat is capable to support wireless network module. It provided Access Point

function for connection of wireless client. Client user will equip the wireless NIC and

connect to the Internet through the air.

Click on the “4th Ethernet” to show the following:

AP Mode Click on “Enable” to activate the Access Point Mode function on this

wireless NIC. If you select the “Disable” system will activate the wireless NIC in

normal user mode. PS: If you want to use in Access Point Mode the wireless NIC

chip set must be Intersil PRISM with version 2.5 or above .

SSID It’s to configure the network ID of Access Point. If you “Disable” the AP Mode

then you will enter network ID for another Access Point on the network.

Channel It’s to configure the access channel among the standard 11 wireless

channel. The default is channel 3. You are allowed to change by your desired. In the

case of Access Point Mode. If user used the WindowsXP the system will

automatically detect the wireless channel.

WEPKey Mode If you “Enable” the encryption function for wireless communication,

the transmission data will encrypted by WEP format. You must also to make

appropriate configuration in the client side.

WEPKey Type Please choose the encryption key type among of 40 bits or 128 bits.

WEPKeys Here please exactly to enter the key for data encryption. Please enter 5

characters for 40 bits encryption and 13 characters for 128 bits encryption.

4. Routing Table: For information on routing table configuration, please refer to Chapter

2 Quick Setup.

5. Hostname: For information on hostname configuration, please refer to Chapter 2

Quick Setup.

6. Nameserver: For information on Name Server configuration, please refer to Chapter

2 Quick Setup.

7. DynDNS: The Maat system support Dynamic DNS service. It provided user to create

their owned web home page even in case of using dynamic IP environment. Please

click on “DynDNS” the screen show as below. Before going to the configuration. You

must first to apply for required user account of dynamic DNS and their password. You

can click on the hyper link “DynDNS” on the lower right of following screen to apply

for above information. Then you are ready to input the user account, password and

domain name to following configuration table.

Chapter 4 System Configuration

System Configuration is the most basic parameter configuration of the Maat system. If you

have completed the quick setup mentioned in Chapter 2, part of parameters will automatically

appear in related fields configured by the system.

After clicking “System” on the left side of the management interface, a screen will appear as

follows:

4.1 Shutdown and Reboot

4.1.1 Shutdown

After clicking “Shutdown” in the “System” management interface, a figure will appear as

follows:

If you have determined to turn off the computer, select “Shutdown”. Then it just takes

30 seconds to one minute to shut down the power supply. You can also shut down the

power supply of the host when the following Maat screen appears!

ページが読み込まれています...

FIC EUN-R02501 ユーザーマニュアル

ブランド: FIC

モデル: EUN-R02501

タイプ: ユーザーマニュアル

このマニュアルも適しています

Maat

PDFをダウンロードします

報告

他の言語で

English: FIC EUN-R02501 User manual

FIC EUN-R02501 ユーザーマニュアル

このマニュアルも適しています

FIC EUN-R02501 ユーザーマニュアル

他の言語で

その他のドキュメント