imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
Blu-ray
™
Disc Player
user manual
BD-J5900
ENGLISH
Safety Information
Warning
This symbol indicates that high volt-
age is present inside. It is dangerous
to make any kind of contact with any
internal part of this product.
This symbol indicates that important
literature concerning operation and
maintenance has been included with
this product.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE THE
COVER(OR BACK). THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER ALL
SERVICING TO QUALIFIED PERSONNEL.
•
The slots and openings in the cabinet and
in the back or bottom are provided for
necessary ventilation. To ensure reliable
operation of this apparatus, and to protect it
from overheating, these slots and openings
must never be blocked or covered.
- Do not place this apparatus in a confined
space, such as a bookcase, or built-
in cabinet, unless proper ventilation is
provided.
- Do not place this apparatus near or over
a radiator or heat register, or where it is
exposed to direct sunlight.
- Do not place vessels (vases etc.)
containing water on this apparatus. A
water spill can cause a fire or electric
shock.
•
Do not expose this apparatus to rain or place
it near water (near a bathtub, washbowl,
kitchen sink, or pool, etc.). If this apparatus
accidentally gets wet, unplug it and contact
an authorized dealer immediately
.
• This apparatus uses batteries. In your
community, there might be environmental
regulations that require you to dispose of
these batteries properly. Please contact
your local authorities for disposal or
recycling information.
• Do not overload wall outlets, extension
cords or adaptors beyond their capacity,
since this can result in fire or electric shock.
• Route power-supply cords so that they
are not likely to be walked on or pinched
by items placed on or against them. Pay
particular attention to cords at the plug
end, at wall outlets, and the point where
they exit from the apparatus.
• To protect this apparatus from a lightning
storm, or when it is left unattended and
unused for long periods of time, unplug
it from the wall outlet and disconnect the
antenna or cable system. This will prevent
damage to the set due to lightning and
power line surges.
• Before connecting the AC power cord
to the DC adaptor outlet, make sure the
voltage designation of the DC adaptor
corresponds to the local electrical supply.
• Never insert anything metallic into the open
parts of this apparatus. Doing so may
create a danger of electric shock.
• To avoid electric shock, never touch the
inside of this apparatus. Only a qualified
technician should open this apparatus.
• Make sure to plug the power cord in until
it is firmly seated. When unplugging the
power cord from a wall outlet, always pull
on the power cord’s plug. Never unplug by
pulling on the power cord. Do not touch
the power cord with wet hands.
• If this apparatus does not operate normally
- in particular, if there are any unusual
sounds or smells coming from it - unplug
it immediately and contact an authorized
dealer or service center.
• Maintenance of Cabinet.
- Before connecting other components to
this product, be sure to turn them off.
- If you move your product suddenly
from a cold place to a warm place,
condensation may occur on the
operating parts and lens and cause
abnormal disc playback. If this occurs,
unplug the product, wait for two hours,
and then connect the plug to the power
outlet. Then, insert the disc, and try to
play back again.
• Be sure to pull the power plug out of the
outlet if the product is to remain unused or
if you are leaving the house for an extended
period of time (especially when children,
elderly, or disabled people will be left alone
in the house).
- Accumulated dust can cause an electric
shock, an electric leakage, or a fire by
causing the power cord to generate
sparks and heat or the insulation to
deteriorate.
•
Contact an authorized service center for
information if you intend to install your
product in a location with heavy dust, high
or low temperatures, high humidity, chemical
substances, or where it will operate 24 hours
a day such as in an airport, a train station,
etc. Failing to do so may lead to serious
damage of your product.
• Use only a properly grounded plug and wall
outlet.
- An improper ground may cause electric
shock or equipment damage. (Class l
Equipment only.)
•
To turn this apparatus off completely, you
must disconnect it from the wall outlet.
Consequently, the wall outlet and power plug
must be readily accessible at all times.
• Do not allow children to hang on the
product.
• Store the accessories (battery, etc.) in a
location safely out of the reach of children.
• Do not install the product in an unstable
location such as a shaky self, a slanted
floor, or a location exposed to vibration.
• Do not drop or strike the product. If the
product is damaged, disconnect the power
cord and contact a service center.
•
To clean this apparatus, unplug the power
cord from the wall outlet and wipe the
product using a soft, dry cloth. Do not
use any chemicals such as wax, benzene,
alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals
can damage the appearance of the product
or erase the printing on the product.
• Do not expose this apparatus to dripping
or splashing. Do not put objects filled with
liquids, such as vases on the apparatus.
• Do not dispose of batteries in a fire.
•
Do not plug multiple electric devices into the
same wall socket. Overloading a socket can
cause it to overheat, resulting in a fire.
• There is danger of an explosion if you
replace the batteries used in the remote
with the wrong type of battery. Replace
only with the same or equivalent type.
•
WARNING - TO PREVENT
THE SPREAD OF FIRE,
KEEP CANDLES AND
OTHER ITEMS WITH OPEN
FLAMES AWAY FROM THIS
PRODUCT AT ALL TIMES.
2
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a
CLASS 1 LASER product. Use of controls,
adjustments or performance of procedures
other than those specified herein may result in
hazardous radiation exposure.
CAUTION :
•
THIS PRODUCT USES AN INVISIBLE
LASER BEAM WHICH CAN CAUSE
HAZARDOUS RADIATION EXPOSURE
IF DIRECTED. BE SURE TO OPERATE
PRODUCT CORRECTLY AS INSTRUCTED.
•
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVERS
AND DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED PERSONNEL.
This product satisfies CE regulations when
shielded cables and connectors are used
to connect the unit to other equipment.
To prevent electromagnetic interference
with electric appliances, such as radios
and televisions, use shielded cables and
connectors for connections.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LÁSER CLASE 1
✎
NOTES
`
If the Region number of a Blu-ray Disc/DVDs
does not correspond to the Region number of
this product, the product cannot play the disc.
IMPORTANT NOTE
The mains lead on this equipment is
supplied with a molded plug incorporating
a fuse. The value of the fuse is indicated
on the pin face of the plug.
If it requires replacing, a fuse approved to
BS1362 of the same rating must be used.
Never use the plug with the fuse cover
omitted if the cover is detachable. If a
replacement fuse cover is required, it must
be of the same colour as the pin face of
the plug. Replacement covers are available
from your dealer.
If the fitted plug is not suitable for the power
points in your house or the cable is not long
enough to reach a power point, you should
obtain a suitable safety approved extension
lead or consult your dealer for assistance.
However, if there is no alternative to cutting
off the plug, remove the fuse and then
safely dispose of the plug. Do not connect
the plug to a mains jack, as there is a risk of
shock hazard from the bared flexible cord.
To disconnect the apparatus from the
mains, the plug must be pulled out from
the mains socket, therefore the mains plug
shall be readily operable.
The product unit accompanying this user
manual is licenced under certain intellectual
property rights of certain third parties.
Precautions
Important Safety Instructions
Read these operating instructions carefully
before using the unit. Follow all the safety
instructions listed below.
Keep these operating instructions handy for
future reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5.
Do not use this apparatus near water.
6. Clean only with a dry cloth.
7.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including AV receivers)
that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or
the third prong are provided for your
safety. If the provided plug does not fit
into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where it exits the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the
cart, stand, tripod,
bracket, or table
specified by the
manufacturer, or sold
with the apparatus.
When a cart is used,
use caution when moving the cart/
apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as when the power-supply
cord or plug is damaged, liquid has
been spilled or objects have fallen into
the apparatus, the apparatus has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
3
SAFETY INFORMATION
Warning ....................................................... 2
Precautions ................................................. 3
Using the 3D function .................................. 4
GETTING STARTED
Before using the User Manual ......................5
Logos of Discs the player can play .............. 5
Accessories ................................................. 7
Front Panel .................................................. 7
Rear Panel ................................................... 7
Remote Control ........................................... 8
CONNECTIONS
Connecting to a TV ...................................... 8
Connecting to an Audio System .................. 9
Connecting to a Network Router ................. 9
SETTINGS
The Setup Procedure .................................10
Menu Navigation ........................................10
Accessing the Settings Menu .................... 11
Picture Settings ......................................... 11
Sound Settings .......................................... 12
Network Settings ....................................... 13
System Settings ........................................ 16
Language Settings .....................................17
Security Settings........................................ 17
General Settings ........................................ 17
Support Settings .......................................18
MEDIA PLAY
Playing a Commercially Recorded Disc ...... 19
Playing Files on a USB Device ................... 19
Playing a Disc with User Recorded
Content ..................................................... 19
Using DLNA ...............................................20
Controlling Video Playback ........................ 20
Controlling Music Playback ........................ 21
Playing Photo Contents ............................. 22
APPENDIX
Troubleshooting ......................................... 23
Specifications ............................................ 24
Using the 3D function
I
MPORTANT HEALTH AND SAFETY
INFORMATION FOR 3D PICTURES.
Read and understand the following safety
information before using the 3D function.
• Some viewers may experience discomfort
while viewing 3D TV such as dizziness,
nausea, and headaches.
If you experience any such symptom,
stop viewing 3D TV, remove the 3D Active
Glasses, and rest.
• Watching 3D images for an extended
period of time may cause eye strain. If you
feel eye strain, stop viewing 3D TV, remove
your 3D Active Glasses, and rest.
• A responsible adult should frequently check
on children who are using the 3D function.
If there are any reports of tired eyes,
headaches, dizziness, or nausea, have the
child stop viewing 3D TV and rest.
• Do not use the 3D Active Glasses for other
purposes (Such as general eyeglasses,
sunglasses, protective goggles, etc.).
• Do not use the 3D function or 3D Active
Glasses while walking or moving around.
Using the 3D function or 3D Active Glasses
while moving around may cause you to
bump into objects, trip, and/or fall, and
cause serious injury.
• If you want to enjoy 3D content, connect
a 3D device (3D compliant AV receiver or
TV) to the player's HDMI OUT port using a
high-speed HDMI cable. Put on 3D glasses
before playing the 3D content.
• The player outputs 3D signals only through
HDMI cable connected to the HDMI OUT
port.
• As the video resolution in 3D play mode
is fixed according to the resolution of the
original 3D video, you can not change the
resolution to your preference.
• Some functions such as BD Wise, screen
size adjustment, and resolution adjustment
may not operate properly in 3D play mode.
• You must use a high-speed HDMI cable for
proper output of the 3D signal.
• Stay at least three times the width of the
screen from the TV when watching 3D
images. For example, if you have a 46-inch
screen, stay 138 inches (11.5 feet) from the
screen.
• Place the 3D video screen at eye level for
the best 3D picture.
• When the player is connected to some 3D
devices, the 3D effect may not function
properly.
• This player does not convert 2D content
into 3D.
• "Blu-ray 3D" and "Blu-ray 3D" logo are
trademarks of the Blu-ray Disc Association.
Contents
4
Getting Started
Before using the User Manual
Disc Types and Contents your player can play
Media Disc Type Details
VIDEO
Blu-ray Disc
3D Blu-ray Disc
BD-ROM or BD-RE/-R recorded in the BD-RE format.
DVD-VIDEO
DVD-RW
DVD-R
DVD+RW
DVD+R
DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R that have
been recorded and finalized, or a USB storage media containing DivX,
MKV or MP4 contents.
MUSIC
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB
storage media containing MP3 or WMA contents.
PHOTO
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB
storage media containing JPEG contents.
✎
NOTES
`
The player may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.
`
If a DVD-RW/-R has not been recorded properly in DVD video format, it will not be playable.
`
Your player will not play content that has been recorded on a DVD-R at a bit-rate that exceeds 10 Mbps.
`
Your player will not play content that has been recorded on a BD-R or USB device at a bit rate that exceeds
25 Mbps.
`
Playback may not work for some types of discs, or when you use specific functions, such as angle change
and aspect ratio adjustment. Information about the discs is written in detail on the disc box. Please refer to
this if necessary.
`
When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.
Disc types your player cannot play
• HD DVD
• DVD-ROM/PD/
MV, etc
• DVD-RAM
• Super Audio CD
(except CD layer)
•
DVD-RW (VR mode)
•
CVD/CD-ROM/CDV/
CD-G/CD-I/LD
(CD-Gs play audio
only, not graphics.)
• 3.9 GB DVD-R for
Authoring.
Region Code
Both players and discs are coded by region.
These regional codes must match for a disc
to play. If the codes do not match, the disc
will not play.
The Region Number for this player is
displayed on the rear panel of the player.
Disc
Type
Region
Code
Area
Blu-ray
Disc
A
North America, Central
America, South America,
Korea, Japan, Taiwan, Hong
Kong and South East Asia.
B
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
C
India, China, Russia, Central
and South Asia.
DVD-
VIDEO
1
The U.S., U.S. territories and
Canada
2
Europe, Japan, the Middle
East, Egypt, Africa, Greenland
3
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
4
Mexico, South America,
Central America, Australia,
New Zealand, Pacific Islands,
Caribbean
5
Russia, Eastern Europe, India,
North Korea, Mongolia
6
China
Logos of Discs the player can play
Blu-ray Disc BD-LIVE
3D Blu-ray Disc DivX
NTSC broadcast system in U.S.A, Canada, Korea,
Japan
Supported File Formats
Notes on the USB connection
•
Your player supports USB storage media,
MP3 players, digital cameras, and USB
card readers.
•
The player does not support folder or file
names longer than 128 characters.
•
Some USB/External HDD/digital camera
devices may not be compatible with the
player.
•
Your player supports the FAT16, FAT32,
and NTFS file systems.
•
Connect USB devices directly to the
player’s USB port. Connecting through
a USB cable may cause compatibility
problems.
•
Inserting more than one memory device
into a multi-card reader may cause the
reader to operate improperly.
•
The player does not support the PTP
protocol.
5
•
Do not disconnect a USB device during a "loading" process.
•
The bigger the image resolution, the longer the image takes to display.
•
This player cannot play MP3 files with DRM (Digital Rights Management) downloaded from
commercial sites.
•
Your player only supports video with a frame rate under 30fps (frames per second).
•
Your player only supports USB Mass Storage Class (MSC) devices such as thumb drives and
USB HDD. (HUB is not supported.)
•
Certain USB HDD Devices, multi-card readers and thumb drives may not be compatible with this
player.
•
If some USB devices require excessive power, they may be limited by the circuit safety device.
•
If playback from a USB HDD is unstable, provide additional power by plugging the HDD into a
wall socket.
If the problem continues, contact the USB HDD manufacturer.
•
SAMSUNG is not responsible for any data file damage or data loss.
•
Your player does not support NTFS compressed files, sparse files, or encrypted files.
•
You can repair or format a USB device on your Desktop PC. (MS-Windows OS only)
Video File Support
File Extension Container Video Codec Audio Codec Resolution
*.avi
AVI
DivX 3.11/4/5/6
MP3
Dolby Digital
DTS
WMA
PCM
1920x1080
MP4v3
H.264 BP/MP/HP
1920x1080
*.mkv
MKV
VC-1 AP
MP3
Dolby Digital
DTS
1920x1080
H.264 BP/MP/HP
1920x1080
*.wmv
WMV (wmv9)
VC-1 AP
WMA
1920x1080
VC-1 SM
1920x1080
*.mp4
MP4
MP4 (mp4v)
AAC
1920x1080
H.264 BP/MP/HP
1920x1080
*.mpg
*.mpeg
MPEG
MPEG1
MP1, 2
Dolby Digital
DTS
1920x1080
MPEG2
1920x1080
H.264 BP/MP/HP
1920x1080
*.rmvb
RMVB
RV8/9/10
(RV30/40)
RealAudio 6
1920x1080
• Limitations
- Even when a file is encoded by a supported codec listed above, the file might not be
played if its content has a problem.
- Normal playback is not guaranteed if the file’s container information is wrong or the file
itself is corrupted.
- Files having a higher Bit rate/frame rate than standard may stutter during sound/video
playback.
- The Seek (skip) function is not available if the file’s index table is damaged.
- Depending on your country, RMVB format may not be supported.
• Video decoder
- Supports up to H.264 Level 4.1 and AVCHD
- Does not support H.264 FMO/ASO/RS and VC1 SP/MP/AP L4
- MPEG4 SP, ASP :
Below 1280 x 720 : 60 frames max
Above 1280 x 720 : 30 frames max
- Does not support GMC 2 or higher
• Audio decoder
- Supports WMA 7, 8, 9 and STD
- Does not support WMA sampling rate of 22050Hz mono.
- AAC: Max sampling rate: 96Khz (8, 11, 12, 16, 22,24, 32,44.1, 48, 64, 88.2, 96)
Max bit rate: 320kbps
Supported DivX subtitle file formats
*.ttxt, *.smi, *.srt, *.sub, *.txt
✎
NOTES
`
Playback of some DivX, MKV or MP4 file may not be supported depending on their video resolution
and frame rate.
Music File Support
File Extension Container Audio Codec Support Range
*.mp3
MP3 MP3
-
*.wma
WMA WMA
* Sampling rates (in kHz) - 8, 11, 16, 22, 32, 44.1, 48
* Bit rates - All bit-rates from 5kbps to 355kbps
6
Picture File Support
File Extension Type Resolution
*.jpg
*.jpeg
*.jpe
JPEG
15360x8640
*.png
PNG
15360x8640
AVCHD (Advanced Video Codec High Definition)
• This player can play back AVCHD format discs. These discs are normally recorded and used
in camcorders.
• The AVCHD format is a high definition digital video camera format.
• The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the
conventional image compressing format.
• Some AVCHD discs use the "x.v.Color" format. This player can play back AVCHD discs that
use "x.v.Color" format.
• "x.v.Color" is a trademark of Sony Corporation.
• "AVCHD" and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd.
and Sony Corporation.
✎
NOTES
`
Some AVCHD format discs may not play, depending on the recording condition.
AVCHD format discs need to be finalized.
`
"x.v.Color" offers a wider colour range than normal DVD camcorder discs.
Accessories
Check for the supplied accessories shown below.
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
HDMI Cable
Batteries for Remote
Control (AAA Size)
User Manual Remote Control
Front Panel
DISC TRAY
POWER BUTTON
OPEN/CLOSE BUTTON
USB HOST
REMOTE CONTROL SENSOR
✎
NOTES
`
You can perform software upgrades using the USB Host jack with a USB flash memory stick only.
`
Please open and pull out the USB cover before inserting USB device.
Rear Panel
HDMI OUT LAN DIGITAL AUDIO OUT
7
Remote Control
Tour of the Remote Control
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
Turn the player on and off.
Allows you to repeat A-B disc.
Press numeric buttons to operate options.
Press to open and close the disc tray.
Use to enter the disc menu.
Press to skip backwards or forwards.
Press to stop a disc.
Press to use bonusview function.
Return to the previous menu.
These buttons are used both for menus on the
player and also several Blu-ray Disc functions.
Use to select menu items and change menu
values.
Press to use Tools menu.
Use to access various audio functions on a
disc (Blu-ray Disc/DVD).
Press to play a disc.
Press to pause a disc.
Turn the TV on and off.
Press to switch the Blu-ray Disc/DVD's
subtitle language.
Use to enter the popup menu/title menu.
Press to search a disc backwards or
forwards.
Press to move to the home menu.
Press to see the full screen on a TV.
During Blu-ray or DVD disc playback, the
Full screen button does not operate.
Press to exit the menu.
Use to display the playback information.
Allows you to repeat a title, chapter, track or
disc.
TV volume adjustment.
After setup, allows you to set the input
source on your TV.
Installing batteries
✎
NOTES
`
If the remote does not operate properly:
•
Check the polarity (+/–) of the batteries.
•
Check if the batteries are drained.
•
Check if the remote sensor is blocked by obstacles.
•
Check if there is any fluorescent lighting nearby.
!
CAUTION
`
Dispose of batteries according to local environmental
regulations. Do not put them in the household trash
`
Do not dispose of batteries in a fire.
`
Do not short circuit, disassemble or overheat the batteries.
`
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Connections
Connecting to a TV
Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN
jack on your TV.
- Do not connect the power cord to the wall outlet until you have made all the other
connections.
- When you change the connections, turn off all devices before you start.
Audio
Video
✎
NOTES
`
If you use an HDMI-to-DVI cable to connect to your display device, you must also connect the Digital Audio
Out on the player to an audio system to hear audio.
`
An HDMI cable outputs digital video and audio, so you don't need to connect an audio cable.
`
Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of
your TV.
`
When you connect the player to your TV using the HDMI cable or to a new TV, and then turn it on for the
first time, the player automatically sets the HDMI output resolution to the highest supported by the TV.
`
A long HDMI cable may cause screen noise. If this occurs, set HDMI Deep Colour to Off in the menu.
`
To view video in the HDMI 720p, 1080i, or 1080p output mode, you must use a High speed HDMI cable.
`
HDMI outputs only a pure digital signal to the TV.
If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on
the screen.
8
Connecting to an Audio System
You can connect the Blu-ray player to an audio system using one of the methods illustrated
below.
- Do not connect the power cord to the wall outlet until you have made all the other
connections.
- When you change the connections, turn off all devices before you start.
Method 1 Connecting to an HDMI compatible AV receiver
• Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN
jack on your receiver.
• Best quality (Recommended)
Method 2
Connecting to an AV receiver with a Digital Coaxial Cable
• Using a digital Coaxial cable (Not supplied), connect the Coaxial Digital Audio Out jack on
the product to the Digital Coaxial In jack of the receiver.
• Good quality
• You will hear sound only through the front two speakers with Digital Output set to PCM.
AudioAudio
Method 2Method 1
Connecting to a Network Router
You can connect your player to your network router using one of the methods illustrated below.
To use the DLNA network functionality, you must connect your PC to your network as shown
in the illustrations.
The connection can be wired or wireless.
Wired Network
Broadband
service
Broadband
service
Broadband modem
(with integrated router)
Broadband
modem
Router
Or
✎
NOTES
`
Internet access to Samsung's software update server may not be allowed, depending on the router you use or your
ISP's policy. For more information, contact your ISP (Internet Service Provider).
`
DSL users, please use a router to make a network connection.
9
Wireless Network
Wireless Router
Broadband service
✎
NOTES
`
If your wireless router supports DHCP, this player can use a DHCP or static IP address to connect to the wireless
network.
`
Set your wireless router to Infrastructure mode. Ad-hoc mode is not supported.
`
The player supports only the following wireless security key protocols:
-
WEP (OPEN/SHARED), WPA-PSK (TKIP/AES),
WPA2-PSK (TKIP/AES)
`
Select a channel on the wireless router that is not currently being used. If the channel set for the wireless router is
currently being used by another device nearby, it will result in interference and communication failure.
`
If you select the Pure High-throughput (Greenfield) 802.11n mode and set the Encryption type on your router to WEP,
TKIP or TKIP-AES (WPS2Mixed), the player will not support a connection in compliance with new Wi-Fi certification
specifications.
`
Wireless LAN, by its nature, may cause interference, depending on the operating conditions (router performance,
distance, obstacles, interference by other radio devices, etc).
Settings
The Setup Procedure
• The Home screen will not appear if you do not
configure the setup.
• The OSD (On Screen Display) may change in this
player after you upgrade the software version.
• The access steps may differ depending on the
menu you selected.
•
After the setup process is complete, the panel
buttons and remote control can be operated.
After you have connected the player to your TV,
turn on the TV and player. When you turn on the
player the first time, the player's Setup screen
appears on the TV. The Setup procedure lets
you set the On Screen Display (OSD) and menu
languages, the aspect ratio (screen size), the
network type, and connect the player to your
network.
✎
NOTES
`
The Home menu will not appear if you do not
configure the setup except as noted below.
`
If you press the BLUE (D) button during network
setup, you can access the Home menu even if
the network setup is not completed yet.
`
When you return to the Home menu, the full
screen mode is cancelled automatically.
`
If you want to display the Setup screen again
to make changes, press the
^
button on
the front panel of the player for more than 5
seconds with no disc inserted. This resets the
player to its default settings.
`
After the setup process is complete. you can
operate the HDMI-CEC function.
`
If you want to use the Anynet+(HDMI-CEC)
function to aid in the initial set up process,
please follow the instructions below.
1)
Connect the player to an Anynet+(HDMI-CEC)
compliant Samsung TV using HDMI Cable.
2) Set the Anynet+(HDMI-CEC) feature to On in
both the TV and the player.
3) Set the TV to the Setup Procedure.
`
If you leave the player in the stop mode for
more than 5 minutes without using it, a screen
saver will appear on your TV. If the player is
left in the screen saver mode for more than 25
minutes, the power will automatically turn off.
Menu Navigation
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
1
2
4
3
1
HOME Button : Press to move to the Home
menu.
2
RETURN Button :
Return to the previous menu.
3
v
(Enter) / DIRECTION Button :
Move the cursor or select an item.
Activate the currently selected item.
Confirm a setting.
4
EXIT Button : Press to exit the current menu.
10
2.
Press the
▲▼
◄► buttons to select
Settings, and then press the
v
button.
3. Press the ▲▼ buttons to select the
desired submenu, and then press the
v
button.
4.
Press the ▲▼ buttons to select the desired
item, and then press the
v
button.
5. Press the EXIT button to exit the menu.
✎
NOTES
`
The access steps may differ depending on
the menu you selected. The OSD (On Screen
Display) may change in this player after you
upgrade the software version.
Picture Settings
You can configure various display options
such as the TV Aspect Ratio, Resolution, etc.
3D Settings
Select whether to play a Blu-ray Disc with 3D
contents in 3D Mode.
✎
NOTES
`
For some 3D discs, to stop a movie during 3D
playback, press the
5
button once.
The movie stops and the 3D mode option is
de-activated.
To change a 3D option selection when you are
playing a 3D movie, press the
5
button once.
The Blu-ray menu appears. Press the
5
button again, then select 3D Settings in the
Blu-ray menu.
`
Depending on the content and the position of
the picture on your TV screen, you may see
vertical black bars on the left side, right side,
or both sides.
TV Aspect Ratio
Depending on the type of television you have,
you may want to adjust the screen size setting.
✎
NOTES
`
D
epending on the disc type, some aspect
ratios may not be available.
`
If you select an aspect ratio and option
which is different than the aspect ratio of
your TV screen, the picture might appear to
be distorted.
BD Wise (Samsung TVs only)
BD Wise is Samsung’s latest inter-
connectivity feature.
When you connect a Samsung player and
a Samsung TV with BD Wise to each other
via HDMI, and BD Wise is on in both the
player and TV, the player outputs video at
the video resolution and frame rate of the
Blu-ray Disc/DVDs.
✎
NOTES
`
When BD Wise is on, the Resolution setting
automatically defaults to BD Wise and BD
Wise appears in the Resolution menu.
`
If the player is connected to a device that
does not support BD Wise, you cannot use
the BD Wise function.
`
For proper operation of BD Wise, set the BD
Wise menu of both the player and the TV to
On.
Resolution
Lets you set the output resolution of the
HDMI video signal to Auto, 1080p, 1080i,
720p or 480p. The number indicates the
number of lines of video per frame. The i
and p indicate interlaced and progressive
scan, respectively. The more lines, the
higher the quality.
Resolution according to the output
mode
• Blu-ray Disc/E-contents/Digital Contents
playback
Output
Setup
HDMI / connected
HDMI Mode
Blu-ray Disc
E-contents/
Digital
contents
BD Wise
Resolution of
Blu-ray Disc
1080p
Auto
Max. Resolution
of TV input
Max. Resolution
of TV input
1080p@60F
(Movie Frame : Off)
1080p@60F 1080p@60F
Movie Frame :
Auto (24 fps)
1080p@24F 1080p@24F
1080i 1080i 1080i
720p 720p 720p
480p 480p 480p
• DVD playback
Output
Setup
HDMI / connected
HDMI Mode
BD Wise 480i
Auto Max. Resolution of TV input
1080p 1080p
1080i 1080i
720p 720p
480p 480p
• Home Menu
App 1 App 2 App 3 App 4
App 5
Screen Mirroring
Change Device
Settings
PLAY DISC PHOTOS VIDEOS MUSIC
No Disc
2
3
7
6
8
1
4
5
1
Selects VIDEOS.
2
Selects MUSIC.
3
Selects Settings.
4
Selects Change Device.
5
Selects Screen Mirroring.
6
Selects PHOTOS.
7
Selects PLAY DISC.
8
Selects applications.
✎
NOTES
`
The Videos, Photos, and Music options require
that you have an appropriate disc inserted into
the player or a USB flash device attached to
the player.
Accessing the Settings Menu
To access the Settings menu and sub-menus,
follow these steps:
1. Press the POWER button.
The Home Menu appears.
11
✎
NOTES
`
If the TV you connected to the player does
not support Movie Frame or the resolution
you selected, the message "If no pictures
are shown after selecting ‘Yes’, please wait
for 15 seconds to return to the previous
resolution." appears. If you select Yes, the
TV’s screen will go blank for 15 seconds,
and then the resolution will revert to the
previous resolution automatically.
`
If the screen stays blank after you have
changed the resolution, remove all discs,
and then press and hold the
^
button on the
front of the player for more than 5 seconds.
All settings are restored to the factory
default. Follow the steps on the previous
page to access each mode and select the
Display Setup that your TV will support.
`
When the factory default settings are
restored, all stored user BD data is deleted.
`
The Blu-ray Disc must have the 24 frame
feature for the player to use the Movie
Frame (24 fps) mode.
Movie Frame (24 fps)
Setting the Movie Frame (24 fps) feature
to Auto allows you to adjust the player’s
HDMI output to 24 frames per second for
improved picture quality.
You can enjoy the Movie Frame (24 fps)
feature only on a TV supporting this frame
rate. You can select Movie Frame only
when the player is in the HDMI 1080p
output resolution modes.
HDMI Colour Format
Lets you set the colour space format for
HDMI output to match the capabilities of
the connected device (TV, monitor, etc).
HDMI Deep Colour
Lets you output video from the HDMI
OUT jack with Deep Colour. Deep Colour
provides more accurate colour reproduction
with greater colour depth.
Progressive Mode
Lets you improve picture quality when viewing
DVDs.
Sound Settings
Digital Output
Lets you select the digital audio output
format that is suitable for your TV or AV
Receiver. For more details, please refer to
the Digital Output Selection table.
Digital Output Selection
Setup PCM
Bitstream
(Unprocessed)
Bitstream
(Re-encoded
DTS)
Bitstream
(Re-encoded
Dolby D)
Connection
HDMI
Receiver
Coaxial
HDMI
Receiver
Coaxial
HDMI Receiver or
Coaxial
HDMI supported
AV receiver or
Coaxial
Audio Stream
on Blu-ray
Disc
PCM Up to 7.1ch PCM 2ch PCM PCM 2ch Re-encoded DTS
Re-encoded
Dolby Digital *
Dolby Digital PCM 2ch PCM 2ch Dolby Digital Dolby Digital Re-encoded DTS
Re-encoded
Dolby Digital *
Dolby Digital Plus PCM 2ch PCM 2ch
Dolby Digital
Plus
Dolby Digital Re-encoded DTS
Re-encoded
Dolby Digital *
Dolby TrueHD PCM 2ch PCM 2ch Dolby TrueHD Dolby Digital Re-encoded DTS
Re-encoded
Dolby Digital *
DTS PCM 2ch PCM 2ch DTS DTS Re-encoded DTS
Re-encoded
Dolby Digital *
DTS-HD High
Resolution Audio
PCM 2ch PCM 2ch
DTS-HD High
Resolution
Audio
DTS Re-encoded DTS
Re-encoded
Dolby Digital *
DTS-HD Master
Audio
PCM 2ch PCM 2ch
DTS-HD
Master Audio
DTS Re-encoded DTS
Re-encoded
Dolby Digital *
Audio Stream
on DVD
PCM PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch
Dolby Digital PCM 2ch PCM 2ch Dolby Digital Dolby Digital Dolby Digital Dolby Digital
DTS PCM 2ch PCM 2ch DTS DTS DTS DTS
Definition for
Blu-ray Disc
Any
Decodes main feature
audio and BONUSVIEW
audio stream together
into PCM audio and add
Navigation Sound Effects.
Outputs only main feature
audio stream so that your
AV receiver can decode the
audio bitstream.
You will not hear BONUSVIEW
audio and Navigation Sound
Effects.
Decodes main feature
audio and BONUSVIEW
audio stream together
into PCM audio
and add Navigation
Sound Effects, then
re-encodes the
PCM audio into DTS
bitstream
Decodes main
feature audio and
BONUSVIEW audio
stream together into
PCM audio and add
Navigation Sound
Effects, then re-
encodes the PCM
audio into Dolby
Digital bitstream
* If Source Stream is 2ch, "Re-encoded Dolby D" Settings are not applied.
Blu-ray Discs may include three audio streams :
- Main Feature Audio : The audio soundtrack of the main feature.
- BONUSVIEW audio : An additional soundtrack such as the director or actor’s commentary.
- Navigation Sound Effects : When you choose a menu navigation selection, a Navigation
Sound Effect may sound. Navigation Sound Effects are different on each Blu-ray Disc.
12
✎
NOTES
`
Be sure to select the correct Digital Output or
you will hear no sound or just loud noise.
`
If the HDMI device (AV receiver, TV) is not
compatible with compressed formats (Dolby
Digital, DTS), the audio signal outputs as PCM.
`
Regular DVDs do not have BONUSVIEW audio
and Navigation Sound Effects.
`
Some Blu-ray Discs do not have BONUSVIEW
audio and Navigation Sound Effects.
`
If you play MPEG audio soundtracks, the audio
signal outputs as PCM regardless of your
Digital Output selections (PCM or Bitstream).
`
If your TV is not compatible with compressed
multi-channel formats (Dolby Digital, DTS), the
player may output PCM 2ch downmixed audio
even though you selected Bitstream (either Re-
encoded or Unprocessed) in the setup menu.
`
If your TV is not compatible with PCM sampling
rates over 48kHz, the player may output 48kHz
downsampled PCM audio even though you set
PCM Downsampling to Off.
PCM Downsampling
Lets you choose to have 96KHz PCM signals
downsampled to 48KHz before they are
outputted to an amplifier. Choose On if your
amplifier or receiver is not compatible with a
96KHz signal.
Dynamic Range Control
Lets you apply dynamic range control to
Dolby Digital, Dolby Digital Plus, and Dolby
TrueHD audio.
• Auto : Automatically controls the dynamic
range of Dolby TrueHD audio, based
on information in the Dolby TrueHD
soundtrack.
Also turns dynamic range control on for
Dolby Digital and Dolby Digital Plus.
Configuring Your Network
Connection
Before you begin, contact your ISP to find
out if your IP address is static or dynamic.
If it is dynamic, and you have a wired or
wireless network, we recommend using
the Automatic configuration procedures
described below.
If you are connecting to a wired network,
connect the player to your router using a
LAN cable before you start the configuration
procedure.
If you are connecting to a wireless network,
disconnect any wired network connection
before you begin.
To begin configuring your network
connection, follow these steps:
Wired Network
Ğ
Wired - Automatic
1.
In the Home screen, select Settings,
and then press the
v
button.
2.
Select Network, and then press the
v
button.
3.
Select Network Settings, and then
press the
v
button.
4.
Select Wired in the Network Settings
screen, and then press the
v
button.
5.
Select Connect button, and then press
the
v
button. The product detects the
wired connection, verifies the network
connection and then connects to the
network.
Ğ
Wired - Manual
I
f you have a static IP address or the
Automatic procedure does not work, you'll
need to set the Network Settings values
manually.
Follow Steps 1 and 2 in Wired - Automatic,
and then follow these steps:
1.
Select Network Status. The player
searches for a network, and then
displays the connection failed message.
2.
On the bottom of the screen, select
IP Settings, and then press the
v
button.
The IP Settings screen appears.
3.
Select the IP Setting field, and then
press the
v
button.
4.
Select Enter manually in the IP Setting
field, and then press the
v
button.
5.
Select a value to enter (IP Address,
for example), and then press the
v
button.
Use the number keypad on your remote
control to enter the numbers for the
value. Use the ◄► buttons on the
remote control to move from entry field
to entry field within a value. When done
with one value, press the
v
button.
6.
Press the ▲ or ▼ button to move
to another value, and then enter the
numbers for that value following the
instructions in Step 5.
7.
Repeat Steps 5 and 6 until you have
filled in all values.
•
Off : Leaves the dynamic range
uncompressed, letting you hear the
original sound.
•
On : Turns dynamic range control on for
all three Dolby formats. Quieter sounds
are made louder and the volume of loud
sounds is reduced.
Downmixing Mode
Lets you select the multi-channel downmix
method that is compatible with your stereo
system. You can choose to have the player
downmix to normal stereo or to surround
compatible stereo.
Network Settings
To begin setting up the network connection
for your player, follow these steps:
1.
In the Home menu, press the ▲▼◄►
buttons to select Settings, and then
press the
v
button.
2.
Press the ▲▼ buttons to select
Network, and then press the
v
button.
3.
Press the ▲▼ buttons to select
Network Settings, and then press the
v
button.
4.
Press the ▲▼ buttons to select
Network Type, and then press the
v
button.
5.
Press the ▲▼ buttons to select Wired
or Wireless, and then press the
v
button.
6.
Go to the next section.
13
✎
NOTES
`
You can get the Network values from your
Internet provider.
8.
When finished entering all the values,
and then press the RETURN or EXIT
buttons. The player verifies the network
connection and then connects to the
network.
Wireless Network
You can setup a wireless network
connection in four ways:
- Wireless Automatic
- Wireless Manual
- WPS(PBC)
- WPS(PIN)
When you configure the wireless network
connection, any wireless network devices
currently connected through the player
or, if applicable, the player's current wired
connection, will be disconnected.
Ğ
Wireless - Automatic
1.
In the Home screen, select Settings,
and then press the
v
button.
2.
Select Network, and then press the
v
button.
3.
Select Network Settings, and then
press the
v
button.
4.
Select Wireless in the Network Settings
screen, and then press the
v
button.
The player searches for and then
displays a list of the available networks.
m
Move
"
Select
'
Return
Network Settings
Select your network type.
Network Type Wireless
Wireless network
Add Network
You can connect your Blu-ray
player to the internet. Please
select which wireless network
to use.
WPS(PBC) Search
5.
Select the desired network, and then
press the
v
button.
6.
On the Security screen, enter your
network's Security Code or Pass
Phrase.
Enter numbers directly using the
number buttons on your remote control.
Enter letters by selecting a letter with
an arrow button, and then pressing
v
button.
7.
When done, select Done and then
press the
v
button. The player verifies
the network connection and then
connects to the network.
8.
When verification is complete, select
OK, and then press the
v
button.
✎
NOTES
`
You should be able to find the Security Code or
Pass Phrase on one of the set up screens you
used to set up your router or modem.
Ğ
Wireless - Manual
If you have a static IP address or the
Automatic procedure does not work, you'll
need to set the Network Settings values
manually.
1. Follow the directions in Wireless -
Automatic through Step 5.
2.
The player searches for a network,
and then displays the connection failed
message.
3.
On the bottom of the screen, select
IP Settings, and then press the
v
button.
The IP Settings screen appears.
4.
Select the IP Setting field, and then
press the
v
button.
5.
Select Enter manually in the IP Setting
field, and then press the
v
button.
6.
Select a value to enter (IP Address, for
example), and then press
v
button.
Use the number keypad on your remote
control to enter the numbers for the
value. Use the ◄► buttons on the
remote control to move from entry field
to entry field within a value. When done
with one value, press the
v
button.
7.
Press the ▲ or ▼ button to move
to another value, and then enter the
numbers for that value following the
instructions in Step 6.
8.
Repeat Steps 6 and 7 until you have
filled in all values.
✎
NOTES
`
You can get the Network values from your
Internet provider.
9.
When finished, and then press the
RETURN or EXIT button. The Security
Screen appears.
10 .
On the Security screen, enter your
network's Security Code or Pass
Phrase. Enter numbers directly using
the number buttons on your remote
control. Enter letters by selecting a letter
with the ▲▼◄► buttons, and then
pressing the
v
button.
11 .
When finished, select Done at the right
of the screen, and then press the
v
button.
The player verifies the network
connection and then connects to the
network.
12 .
After the player verifies the network,
select OK, and then press the
v
button.
Ğ
WPS(PBC)
1.
In the Home screen, select Settings,
and then press the
v
button.
2.
Select Network, and then press the
v
button.
3.
Select Network Settings, and then
press the
v
button.
4.
Select Wireless in the Network Settings
screen, and then press the
v
button.
5.
Press the ▲▼ button on your remote,
and then press the ◄► button to select
the WPS(PBC).
6.
Press the
v
button on your remote.
The "Press the PBC button" message
appears.
14
7.
Press the WPS(PBC) button on your
router within two minutes. Your player
automatically acquires all the network
settings values it needs and connects
to your network.
The Network Status screen appears.
The player connects to the network
after the network connection is verified.
Ğ
WPS(PIN)
Before you begin, open the router's setup
menu on your PC and access the screen
with the WPS PIN entry field.
1.
In the Home screen, select Settings,
and then press the
v
button.
2.
Select Network, and then press the
v
button.
3.
Select Network Settings, and then
press the
v
button.
4.
Select Wireless in the Network Settings
screen, and then press the
v
button.
The player searches for and then
displays a list of the available networks.
5.
Select the desired network, and then
press the ► button.
6.
Select the WPS(PIN), and then press
the
v
button. The PIN pop-up
appears.
7.
Enter the PIN into the WPS PIN entry
field in the router's Set Up screen and
then save the the screen.
✎
NOTES
`
Contact the manufacturer of the router
for instructions explaining how to access
the route's Set Up screens or refer to the
router's user's manual.
`
For WPS connection, set your wireless
router’s security encryption to AES. Setting
to WEP security encryption does not support
WPS connection.
Network Test
Use this menu item to check whether your
network connection is working or not.
Network Status
Use to check whether a connection to a
network and the Internet has been established.
Wi-Fi Direct
The Wi-Fi Direct function allows you to
connect Wi-Fi Direct devices to the player
and each other using a peer-to-peer network,
without a wireless router.
✎
NOTES
`
Some Wi-Fi Direct devices may not support
the DLNA function if connected via Wi-
Fi Direct. If this is the case, it is advisable
to change the network connection method
between devices.
`
Bluetooth transmissions can interfere
with the Wi-Fi Direct signal. Before you
use the Wi-Fi Direct function, we strongly
recommend that you turn off the Bluetooth
function of any active mobile device.
1. Turn on the Wi-Fi direct device and
activate its Wi-Fi Direct function.
2. In the Home screen, select Settings, and
then press the
v
button.
3. Select Network, and then press the
v
button.
4. Select Wi-Fi Direct, and then press the
v
button.
The Wi-Fi Direct devices that you can
connect appear.
5. You have three ways to complete the Wi-
Fi connection:
• Through the Wi-Fi device.
• Through the player using PBC.
• Through the player using a PIN.
Each is covered below.
Through the Wi-Fi Device
1.
On the Wi-Fi device, follow the
procedure on the device for connecting
to another Wi-Fi Direct device. See the
device's user manual for instructions.
2.
When you have completed the
procedure, you should see a pop-up on
your TV screen saying that a device that
supports Wi-Fi Direct has requested to
connect. Select OK, and then press the
v
button to accept.
3.
The Connecting pop-up appears,
followed by the Connected pop-up.
When it closes, you should see the
device listed on the Wi-Fi Direct screen
as connected.
Through the Player Using PBC
1. Select the Wi-Fi Direct device you want
to connect to this player, and then press
the
v
button. The PBC/PIN pop up
appears.
2. Select PBC, and then press the
v
button. The PBC pop-up appears.
3. Press the PBC button on the Wi-Fi Direct
device within 2 minutes.
4. The Connecting pop-up appears,
followed by the Connected pop-up. When
it closes, you should see the device listed
on the Wi-Fi Direct screen as connected.
Through the Player Using a PIN
1.
Select the Wi-Fi Direct device you want
to connect to this player, and then press
the
v
button. The PBC/PIN pop up
appears.
2.
Select PIN, and then press the
v
button. The PIN pop-up appears.
3.
Note the PIN code in the pop-up, and
then enter it into the appropriate field
in the Wi-Fi Direct device you want to
connect.
4.
The Connecting pop-up appears,
followed by the Connected pop-up.
When it closes, you should see the
device listed on the Wi-Fi Direct screen
as connected.
15
✎
NOTES
`
The current wired or wireless network
connection will be disconnected when you use
the Wi-Fi Direct function.
`
Text files, such as files with a .TXT or .DOC
extension, will not display when you are using
the Wi-Fi Direct function.
Screen Mirroring
The Screen Mirroring function lets you view
the screen of your smart phone or android
tablet on the TV you have connected to the
Blu-ray player.
1.
In the Home menu, press the ▲▼◄►
buttons to select Screen Mirroring, and
then press the
v
button. The Screen
Mirroring pop-up appears.
2.
Launch DLNA Cast on your device.
3.
On your device, find the name of the
Blu-ray player in the list of available
devices and then select it.
4.
The TV will display a PIN. Enter the PIN
into your device.
5.
The TV displays a connecting
message (for example, Connecting to
Android_92gb...) and then displays the
connected message.
6.
In a few moments, the screen of your
device appears on the TV screen.
7.
To stop Screen Mirroring, press the
EXIT or RETURN button on the remote
control, or disable Screen Mirroring
function of your smart phone.
✎
NOTES
`
You can connect to a device that supports
DLNA Cast. Note that connecting to such a
device may not be fully supported depending
on the manufacturer. For further information
on mobile connection support, refer to the
manufacturer’s web site.
`
When you are using the Screen Mirroring
function, video stuttering or audio dropouts
may occur, depending on your environment.
`
Bluetooth transmissions can interfere with
the Screen Mirroring signal. Before using
the Screen Mirroring function, we strongly
recommend that you turn off the Bluetooth
function on your smart phone or smart
device (tablet, etc.).
Device Name
Device Name function allows you to change
player's name by selecting from device name
list.
BD-Live Internet Connection
Set to allow or prohibit an Internet
connection when you use the BD-LIVE
service.
•
Allow (All) : The Internet connection is
allowed for all BD-LIVE contents.
•
Allow (Valid Only) : The Internet
connection is allowed only for BD-LIVE
contents containing a valid certificate.
•
Prohibit : No Internet connection is
allowed for any BD-LIVE content.
✎
NOTES
`
What is a valid certificate?
When the player uses BD-LIVE to send
the disc data and a request to the server
to certify the disc, the server uses the
transmitted data to check if the disc is valid
and sends the certificate back to the player.
`
The Internet connection may be restricted
while you are using BD-LIVE contents.
Using BD-LIVE™
Once the player is connected to the
network, you can enjoy various movie-
related service contents using a BD-LIVE
compliant disc.
1.
Attach a USB memory stick to the
USB jack on the front of the player, and
then check its remaining memory. The
memory device must have at least 1GB
of free space to accommodate the BD-
LIVE services.
2.
Insert a Blu-ray Disc that supports BD-
LIVE.
3.
Select an item from various BD-LIVE
service contents provided by the disc
manufacturer.
✎
NOTES
`
The way you use BD-LIVE and the provided
contents may differ, depending on the disc
manufacturer.
The DLNA Function
DLNA lets you play music, video, and photo
files located in your PC on the player.
To use DLNA with your player, you must
connect the player to your network.
(See page 13-16).
To use DLNA with your PC, you must install
DLNA software on your PC.
System Settings
Setup
By using the Setup function, you can set
the language, Network Settings, etc.
For more information about the Setup
function, refer to the Setup section of this
user manual (See page 10).
Quick Start
You can turn on the power quickly by
decreasing the boot time.
✎
NOTES
`
If this function is set to On, Standby power
consumption will be increased.
16
Anynet+ (HDMI-CEC)
Anynet+ is a convenient function that offers
linked operations with other Samsung
players that have the Anynet+ feature.
To operate this function, connect this player
to an Anynet+ Samsung TV with an HDMI
cable.
With Anynet+ on, you can operate this
player using a Samsung TV remote control
and start disc playback simply by pressing
the PLAY (
) button on the TV’s remote
control.
For more information, please see the TV
user manual.
✎
NOTES
`
This function is not available if the HDMI
cable does not support CEC.
`
If your Samsung TV has an Anynet+ logo,
then it supports the Anynet+ function.
`
Depending on your TV, certain HDMI output
resolutions may not work.
Please refer to the user manual of your TV.
`
After the product was turned off,
disconnecting and connecting the power
cable turns it on automatically. At the
moment, it automatically turns off in about
15 seconds for re-establishing Anynet+
connection.
`
For some TV products, if connected to this
product with Anynet+ function, turning
the TV on may display a warning popup
message saying no connection was found.
Still, Anynet+ connection is properly
established and available to use.
BD Data Management
Enables you to manage the downloaded
contents you accessed through a Blu-ray
disc that supports the BD-LIVE service and
stored on a flash drive.
You can check the device’s information
including the storage size, delete the BD
data, or change the Flash memory device.
✎
NOTES
`
In the external memory mode, disc playback
may be stopped if you disconnect the USB
device in the middle of playback.
`
Your player supports the FAT16, FAT32, and
NTFS file systems. We recommend you use
USB devices that support USB 2.0 protocol
with 4 MB/sec or faster read/write speed.
`
The Resume Play function may not work
after you format the storage device.
`
The total memory available to BD Data
Management may differ, depending on the
conditions.
DivX® Video On Demand
View DivX® VOD Registration Codes to
purchase and play DivX® VOD contents.
Language Settings
You can select the language you prefer for
the On-Screen menu, disc menu, audio, and
subtitles.
✎
NOTES
`
The selected language will only appear if it is
supported on the disc.
Security Settings
The default security PIN is 0000. Enter the
default PIN to access the security function if
you haven't created your own PIN. After you
have accessed the security function for the
first time, change the PIN using the Change
PIN function.
BD Parental Rating
Prevents playback of Blu-ray Discs with
specific age ratings unless the 4 digit PIN is
entered.
DVD Parental Rating
This function works in conjunction with
DVDs that have been assigned an age
rating or numeric rating that indicates
the maturity level of the content. These
numbers help you control the types of
DVDs that your family can watch.
Select the rating level you want to set.
For example, if you select Level 6, discs
rated above 6 - Level 7 and 8 - will not play.
A larger number indicates more mature
content.
Change PIN
Change the 4-digit password used to
access security functions.
If you forget your password
1. Remove any discs.
2. Press and hold the
^
button on the front
panel for 5 seconds or more.
All settings will revert to the factory settings.
✎
NOTES
`
When the factory default settings are
restored, all the user stored BD data will be
deleted.
General Settings
Time Zone
Lets you specify the time zone that is
applicable to your area.
17
Support Settings
Software Upgrade
The Software Upgrade menu allows
you to upgrade the player’s software for
performance improvements or additional
services.
By Online
To upgrade By Online, follow these steps:
1. In the player’s menu, go to Settings >
Support > Software Upgrade.
2. Select By Online, and then press the
v
button. The Connecting to Server
message appears.
3. A popup message will appear if an update
is available.
4. If you select Yes, download process
started. (Never turn the player on during
an upgrade.)
5. When the update is completed, the player
will restart automatically.
✎
NOTES
`
The upgrade is complete when the player
turns off, and then turns on again by itself.
`
Never turn the player off or back on manually
during the update process.
`
Samsung Electronics takes no legal
responsibility for player malfunction caused
by an unstable Internet connection or
consumer negligence during a software
upgrade.
`
No disc should be in the product when you
upgrade the software By Online.
By USB
To upgrade by USB, follow these steps:
1.
Visit www.samsung.com/bluraysupport.
2.
Download the latest USB software
upgrade zip archive to your computer.
3.
Unzip the zip archive to your computer.
You should have a single RUF file with
the same name as the zip file.
4.
Copy the RUF file to a USB flash drive.
5.
Make sure there is no disc in the player,
and then insert the USB flash drive into
the USB port of the player.
6.
In the player’s menu, go to Settings >
Support > Software Upgrade.
7.
Select By USB.
✎
NOTES
`
No disc should be in the product when you
upgrade the software using the USB Host
jack.
`
When the software upgrade is done, check
the software details in the software Upgrade
menu.
`
Do not turn off the player during the
software upgrade. It may cause the player to
malfunction.
`
Software upgrades using the USB Host jack
must be performed with a USB flash memory
stick only.
Auto Upgrade Notification
If you have connected the player to your
network, and then set Auto Upgrade
Notification on, the player automatically
notifies you when a new software version is
available for the player.
To set Auto Upgrade Notification on, follow
these steps:
1.
Select Auto Upgrade Notification, and
then press the
v
button.
2.
Use the ▲▼ buttons to select On, and
then press the
v
button.
If there is a new software version available,
the player notifies you with a popup
message.
1.
To upgrade the firmware, select Yes
in the Pop-up. The player turns off
automatically, then restarts, and begins
the download. (Never turn the player on
or off manually during an upgrade.)
2.
The update progress popup appears.
3.
When the update is completed, the
player will restart automatically.
✎
NOTES
`
The upgrade is complete when the player
turns off, and then turns on again by itself.
`
Never turn the player off or on manually
during the update process.
`
Samsung Electronics takes no legal
responsibility for player malfunction caused
by an unstable Internet connection or
consumer negligence during software
upgrade.
Contact Samsung
Provides contact information for assistance
with your player.
Terms of Service Agreement
Lets you view the general disclaimer
regarding third party contents and services.
Reset
Returns all settings to their factory defaults
except for the network settings.
18
Media Play
Playing a Commercially Recorded
Disc
1. Press the
8
button to open the disc tray.
2. Place a disc gently into the disc tray with
the disc's label facing up.
3. Press the
8
button to close the disc tray.
Playback starts automatically.
Playing Files on a USB Device
There are two methods you can use to play or
view multimedia files located on a USB device
through your player.
Method 1
1. Turn the player on.
2. Connect the USB device to the USB port
on the front panel of the player. The New
Device Connected pop-up appears.
App 1 App 2 App 3 App 4 App 5
Screen Mirroring
Change Device
Settings
PLAY DISC PHOTOS VIDEOS MUSIC
No Disc
New device connected.
Photos
Videos
Music
123
>
Move
"
Enter
'
Return
✎
NOTES
`
If the pop-up does not appear, go to Method 2.
3. Use the ▲▼ buttons to select Photos,
Videos or Music, and then press the
v
button. The Photos, Videos & Music
screen appears listing the content of the
device. Depending on how the contents
is arranged, you will see either folders,
individual files, or both.
✎
NOTES
`
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 3. For
example, if you selected music, you will only
be able to see music files. You can change this
selection by returning to the Photos, Videos &
Music screen and going to Step 3 in Method 2
below.
4. If necessary, use the ▲▼◄► buttons to
select a folder, and then press the
v
button.
5. Select a file to view or play, and then
press the
v
button.
6. Press the RETURN button to exit a folder
or the EXIT button to return to the Home
screen.
7. Go to pages 20~22 for instructions that
explain how to control playback of videos,
music, and pictures on a USB device.
Method 2
1. Turn the player on.
2. Connect the USB device to the USB port
on the front panel of the player. Select
Change Device and then press the ▲▼
button to select USB. Press the
v
button.
App 1 App 2 App 3 App 4 App 5
More
Screen Mirr oring
Change Device
Settings
PLAY DISC PHOTOS VIDEOS
MUSIC
No Disc
Change Device
No Disc
123
a
Close
3. Use the ▲▼◄► buttons to select
PHOTOS, VIDEOS or MUSIC on the
Home screen, and then press the
v
button. The Photos, Videos & Music
screen appears listing the content of the
device. Depending on how the contents
is arranged, you will see either folders,
individual files, or both.
✎
NOTES
`
Even though the player will display folders
for all content types, it will only display files
of the Content Type you selected in Step
3. For example, if you selected music, you
will only be able to see music files. You
can change this selection by returning to
the Photos, Videos & Music screen and
repeating Step 3.
4. If necessary, use the ▲▼◄► buttons to
select a folder, and then press the
v
button.
5. Use the ▲▼◄► buttons to select a file
to view or play, and then press the
v
button.
6. Press the RETURN button to exit a folder
or the EXIT button to return to Home
screen.
7. Go to pages 20~22 for instructions that
explain how to control playback of videos,
music, and pictures on a USB device.
✎
NOTES
`
If you insert a disc when playing a USB
device, the device mode changes to "Disc"
automatically.
Playing a Disc with User Recorded
Content
You can play multimedia files you have
recorded on Blu-ray, DVD, or CD discs.
1.
Place a user recorded disc into the disc
tray with the disc’s label facing up, and
then close the tray.
2.
Use the ◄► buttons to select the type
of content you want to view or play -
VIDEOS, PHOTOS, or MUSIC - and
then press the
v
button.
✎
NOTES
`
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 2. For
example, if you selected music, you will only
be able to see music files. You can change this
selection by returning to the Home screen and
repeating Step 2.
19
3.
A screen appears listing the contents
of the disc. Depending on how the
contents are arranged, you will see
either folders, individual files, or both.
4.
If necessary, use the ▲▼◄► buttons
to select a folder, and then press the
v
button.
5.
Use the ◄►▲▼ buttons to select a file
to view or play, and then press the
v
button.
6.
Press the RETURN button one or more
times to exit a current screen, exit a
folder, or to return to the Home screen.
Press the EXIT button to return directly
to the Home Screen.
7.
Go to pages 20~22 for instructions
that explain how to control playback of
videos, music, and pictures on a disc.
Using DLNA
DLNA Connection
PC Blu-ray Disc Player
Play back PC's
files
1. Connect the Blu-ray Disc Player, your PC,
and/or your DLNA compatible device to
the same wireless network.
2.
Follow the directions in the DLNA
software Installation/Instruction manual
to set up devices and files for playing or
viewing.
3.
Select Change Device on the player's
Home screen, and then press the
v
button. In the list of DLNA connected
devices that appears, select your PC
or other DLNA compatible device, and
then press the
v
button.
4.
Use the ◄► buttons to select the type
of content you want to view or play -
VIDEOS, PHOTOS, or MUSIC - and
then press the
v
button.
✎
NOTES
`
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 4. For
example, if you selected music, you will only
be able to see music files. You can change this
selection by returning to the Home screen and
repeating Step 4.
5.
A screen appears listing the contents
of the PC or DLNA device. Depending
on how the contents are arranged, you
will see either folders, individual files, or
both.
6.
If necessary, use the ▲▼◄► buttons
to select a folder, and then press the
v
button.
7.
Use the ◄►▲▼ buttons to select a file
to view or play, and then press the
v
button.
8.
Press the RETURN button one or more
times to exit a current screen, exit a
folder, or to return to the Home screen.
Press the EXIT button to return directly
to the Home Screen.
9.
Go to pages 20~22 for instructions
that explain how to control playback of
videos, music, and pictures on a disc.
Controlling Video Playback
You can control the playback of video
content located on a Blu-ray disc, DVD,
CD, USB device, or your computer.
Depending on the media, some of the
functions described in this manual may not
be available.
During Blu-ray or DVD disc playback, the
Full screen button does not operate.
Buttons on the Remote Control
used for Video Playback
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
1
2
Playback related buttons
The player does not play sound in Search,
Slow or Step mode.
• To return to normal speed playback, press
the
6
button.
6
button
Starts playback.
5
button
Stops playback.
7
button
Pauses playback.
Fast Motion
Play
During playback, press the
3
or
4
button.
Each time you press the
3
or
4
button, the playback speed
will change.
Slow Motion
Play
In pause mode, press the
4
button.
Each time you press the
4
button, the playback speed will
change.
Step Motion
Play
In pause mode, press the
7
button.
Each time you press the
7
button, a new frame appears.
Skip Motion
Play
During playback, press the
1
or
2
button.
Each time you press the
1
or
2
button, the disc moves to the
previous or next chapter or file.
Using the disc menu, title menu,
popup menu, and title list
DISC MENU
button
During playback, press this button
to start the disc menu function.
TITLE MENU
button
During playback, press this button
to start the title menu function.
POPUP MENU
button
During playback, press this button
to start the popup menu function.
20
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
他の言語で
- English: Samsung 藍光播放器 BD-J5900 User manual