Circular Saw
C 9U2
Handling instructions
Keep for future reference
English
2
3
4
5
6
7
○
8
9
10
○
○
○
○
○
○
11
12
13
27
2
1
3
4
5
6
7
8
9
10
11
12
13 14 15 16
17
18
19
20
21
22
23
24
25
26
28
29
30
B
B
A
A
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
56
57
58
59
60
61
79
53
54
55A
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
501
502 503
505
506
14
1 673-002 1 HK1212
2 303-789 1
3 303-790 1
4 303-797 2 M6 × 14
5 998-887 1
6 620-3VV 1
6203VVCMPS2L
7 325-353 1
8 303-805 1
9 303-804 1
10 992-013 2 M5 × 14
11 326-802 1
12-1 303-809 1 235MM-D15.9
HOLE-NT20
12-2 303-810 1 235MM-D30
HOLE-NT20
13 325-354 1
1 4 ––––––––––– 1
15 324-669 1
16 324-139 1
17 302-464 1
18 304-043 1 M4 × 10
19 302-423 1
20 324-662 1 M8 × 15.5
21 305-691 4 M4 × 14
22 937-623 2
23 340-660Q 1 220V – 230V, “22”
24 325-352 1
25 360-759E 1 220V – 230V
26 303-793 1
27 949-884 1 D8 × 50
28 325-350 1
29 961-729 1
30 949-794 1 M6 × 20
31 325-356 1
32 325-355 1
33 600-0VV 1
6000VVCMPS2L
34 960-251 2 D5 × 65
35 620-2VV 1
6202VVCMPS2L
36 303-792 1
37 324-660 1
38 676-531 1 P-7
39 303-801 1
40 324-658 1 M8
41 949-433 1 M8
42 301-806 1 M6 × 15
43 947-859 1
44 302-469 1 M6 × 6
45 325-360 1 “.40, 41, 46-50,
54, 55, 79”
46 317-333 1 M4 × 6
47 324-659 1
48 302-457 1 M8 × 30
49 308-481 1
50 308-482 1 D6 × 24
51 303-806 1
52 324-664 1 M8 × 10
53 303-800 1 M8
54 949-425 1 M6
55A 328-932 1 M6 × 20
56 301-653 5 D4 × 20
5 7 ––––––––––– 1
58 325-358 1
59 325-359 1
60 303-796 3 M5 × 40
61 938-477 2 M5 × 8
62 983-362 2
63 999-038 2
64 961-781 2
65 325-362 1 “61, 62”
66 938-307 1
67 958-049 1 D8.2
68 500455Z 1
69 325-357 1
70 305-720 1 D4 × 12
71 980-063 1
72 946-362 1
73 325-351 1
74 980-063 1
75 930-039 1
76 984-750 2 D4 × 16
77 937-631 1
79 308-480 1 D6 × 17
501 303-888 1
502 872-422 1 6MM
503 303-338 1
505 303-811 1
506 949-340 2 M6 × 16
English
15
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious
injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence
of fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
CONTENTS
GENERAL POWER TOOL SAFETY WARNINGS ........................................15
SAFETY INSTRUCTIONS FOR ALL SAWS ................................................17
FURTHER SAFETY INSTRUCTIONS FOR ALL SAWS ..............................18
SAFETY INSTRUCTIONS FOR SAWS WITH INNER PENDULUM
GUARD ........................................................................................................19
ADDITIONAL SAFETY INSTRUCTIONS FOR ALL SAWS WITH RIVING
KNIFE ..........................................................................................................20
PRECAUTIONS ON USING CIRCULAR SAW ............................................20
SYMBOL .......................................................................................................20
SPECIFICATIONS ........................................................................................ 21
STANDARD ACCESSORIES .......................................................................21
OPTIONAL ACCESSORIES (sold separately)..............................................21
APPLICATIONS ............................................................................................21
PRIOR TO OPERATION ...............................................................................21
ADJUSTING THE SAW PRIOR TO USE ......................................................22
CUTTING PROCEDURES ............................................................................24
MOUNTING AND DISMOUNTING THE SAW BLADE ................................. 24
MAINTENANCE AND INSPECTION ............................................................ 25
SERVICE PARTS LIST .................................................................................27
English
16
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodifi ed plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool.
Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a
power tool.
Do not use a power tool while you are tired or under the infl uence of drugs,
alcohol or medication.
A moment of inattention while operating power tools may result in serious personal
injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before
connecting to power source and/or battery pack, picking up or carrying the
tool.
Carrying power tools with your fi nger on the switch or energising power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
English
17
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn it on and off .
Any power tool that cannot be controlled with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools.
Such preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may aff ect the power toolʼs
operation.
If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed.
Use of the power tool for operations diff erent from those intended could result in a
hazardous situation.
5) Service
a) Have your power tool serviced by a qualifi ed repair person using only identical
replacement parts.
This will ensure that the safety of the power tool is maintained.
CAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of children and infi rm persons.
SAFETY INSTRUCTIONS FOR ALL SAWS
DANGER
a) Keep hands away from cutting area and the blade. Keep your second hand on
auxiliary handle, or motor housing.
If both hands are holding the saw, they cannot be cut by the blade.
b) Do not reach underneath the workpiece.
The guard cannot protect you from the blade below the workpiece.
English
18
c) Adjust the cutting depth to the thickness of the workpiece.
Less than a full tooth of the blade teeth should be visible below the workpiece.
d) Never hold piece being cut in your hands or across your leg. Secure the workpiece
to a stable platform.
It is important to support the work properly to minimize body exposure, blade binding, or
loss of control.
e) Hold power tool by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal parts of the power tool “live” and
shock the operator.
f) When ripping always use a rip fence or straight edge guide.
This improves the accuracy of cut and reduces the chance of blade binding.
g) Always use blades with correct size and shape (diamond versus round) of arbour
holes.
Blades that do not match the mounting hardware of the saw will run eccentrically, causing
loss of control.
h) Never use damaged or incorrect blade washers or bolt.
The blade washers and bolt were specially designed for your saw, for optimum
performance and safety of operation.
FURTHER SAFETY INSTRUCTIONS FOR ALL SAWS
Causes and operator prevention of kickback:
— kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an
uncontrolled saw to lift up and out of the workpiece toward the operator;
— when the blade is pinched or bound tightly by the kerf closing down, the blade stalls and
the motor reaction drives the unit rapidly back toward the operator;
— if the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the
blade can dig into the top surface of the wood causing the blade to climb out of the kerf and
jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can
be avoided by taking proper precautions as given below.
a) Maintain a fi rm grip with both hands on the saw and position your arms to resist
kickback forces.
Position your body either side of the blade, but not in line with the blade.
Kickback could cause the saw to jump backwards, but kickback forces can be controlled by
the operator, if proper precautions are taken.
b) When blade is binding, or when interrupting a cut for any reason, release the
trigger and hold the saw motionless in the material until the blade comes to a
complete stop.
Never attempt to remove the saw from the work or pull the saw backward while the
blade is in motion or kickback may occur.
Investigate and take corrective actions to eliminate the cause of blade binding.
English
19
c) When restarting a saw in the workpiece, centre the saw blade in the kerf and check
that saw teeth are not engaged into the material.
If saw blade is binding, it may walk up or kickback from the workpiece as the saw is
restarted.
d) Support large panels to minimize the risk of blade pinching and kickback.
Large panels tend to sag under their own weight.
Supports must be placed under the panel on both sides, near the line of cut and near the
edge of the panel.
e) Do not use dull or damaged blades.
Unsharpened or improperly set blades produce narrow kerf causing excessive friction,
blade binding and kickback.
f) Blade depth and bevel adjusting locking levers must be tight and secure before
making cut.
If blade adjustment shifts while cutting, it may cause binding and kickback.
g) Use extra caution when making a “plunge cut” into existing walls or other blind
areas.
The protruding blade may cut objects that can cause kickback.
SAFETY INSTRUCTIONS FOR SAWS WITH INNER
PENDULUM GUARD
a) Check lower guard for proper closing before each use. Do not operate the saw if
lower guard does not move freely and close instantly. Never clamp or tie the lower
guard into the open position.
If saw is accidentally dropped, lower guard may be bent.
Raise the lower guard with the retracting handle and make sure it moves freely and does
not touch the blade or any other part, in all angles and depth of cut.
b) Check the operation of the lower guard spring. If the guard and the spring are not
operating properly, they must be serviced before use.
Lower guard may operate sluggishly due to damaged parts, gummy deposits, or build-up of
debris.
c) Lower guard should be retracted manually only for special cuts such as “plunge
cuts” and “compound cuts”. Raise lower guard by retracting handle and as soon
as blade enters the material, the lower guard must be released.
For all other sawing, the lower guard should operate automatically.
d) Always observe that the lower guard is covering the blade before placing saw
down on bench or floor.
An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is
in its path.
Be aware of the time it takes for the blade to stop after switch is released.
English
20
ADDITIONAL SAFETY INSTRUCTIONS FOR ALL SAWS
WITH RIVING KNIFE
a) Use the appropriate riving knife for the blade being used.
For the riving knife to work, it must be thicker than the body of the blade but thinner than the
tooth set of the blade.
b) Adjust the riving knife as described in this instruction manual.
Incorrect spacing, positioning and alignment can make the riving knife ineffective in
preventing kickback.
c) Always use the riving knife except when plunge cutting.
Riving knife must be replaced after plunge cutting. Riving knife causes interference during
plunge cutting and can create kickback.
d) For the riving knife to work, it must be engaged in the workpiece.
The riving knife is ineffective in preventing kickback during short cuts.
e) Do not operate the saw if riving knife is bent.
Even a light interference can slow the closing rate of a guard.
PRECAUTIONS ON USING CIRCULAR SAW
1. Do not use saw blades which are deformed or cracked.
2. Do not use saw blades made of high speed steel.
3. Do not use saw blades which do not comply with the characteristics specified in
these instructions.
4. Do not stop the saw blades by lateral pressure on the disc.
5. Always keep the saw blades sharp.
6. Ensure that the lower guard moves smoothly and freely.
7. Never use the circular saw with its lower guard fixed in the open position.
8. Ensure that the retraction mechanism of the guard system operates correctly.
9. The saw blades body must be thinner than the riving knife and the width of cut, or
kerf (with teeth set) must be greater than the thickness of the riving knife.
10. Never operate the circular saw with the saw blade turned upward or to the side.
11. Ensure that the material is free of foreign matters such as nails.
12. The riving knife should always be used except when plunging in the middle of the
workpiece.
13. For models C9U2, the saw blades should be 235 mm.
14. Disconnect the plug from the receptacle before carrying out any adjustment,
servicing or maintenance.
SYMBOL
WARNING
The following show symbols used for the machine. Be sure that you understand their
meaning before use.
To reduce the risk of injury, user must read instruction manual.
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
他の言語で
- English: Hikoki C 9U2 User manual
その他のドキュメント
-
Hitachi CE 18DSL Handling Instructions Manual
-
-
-
-
-
-
-
Philips AIB6359/93 ユーザーマニュアル
-
DeWalt DWE7492 ユーザーマニュアル
-
GYS ELECTRO POWER - kit complet (2 valises) データシート