Welcome
Thank you for your purchase.
Your new thermostat will provide uniform and comfortable
temperature control throughout every room in your property. We
bring together technology,
materials to provide you with a safe, reliable product combined with
sleek, contemporary design.
programming manual for comprehensive
thermostat. Please also
ensure a suitably qualified person installs your thermostat and
In the box you will find
Thermostat Screws
User Guide 1pc 2pc
1pc
QC Passed 1pc Floor Sensor (2.5m) 1pc
ABOUT YOUR THERMOSTATS
The BHT-3000 range has been developed to control electric
MODEL DEFINITION
GC: Water/Gas Boiler, 5A
L: Backlight
P: Weekly Programmable
W: Wifi
S2: Both internal sensor and floor external sensor
For example: BHT-3000 GCLP
2
FEATURES
2. 65.9*48.6 mm display area helps to protect your eyes.
5. Amazing Silver Frame opens your modern life.
6. The visiable thickenss above the wall is only 13 mm.
8. 86mm hidden box and european 60mm round box is suitable.
9. White, black or gold housing creates your colorful life.
On Appearance
2. 0.5°C Accuracy keeps temperature within the level you set.
3. Data memory when power is off.
4. 5+2 six periods programmable maximize comfort and economy.
TECHNICAL DATA
Power Supply: 95 ~ 240 VAC, 50 ~ 60HZ
Sensor: NTC3950, 10K
Accuracy: ±0.5
Set Temp. Range: 5 -35
Dispaly Temp. Range: 5 ~ 99
Ambient Temp.: 0 ~ 45
Ambient Humidity: 5 ~ 95 % RH (Non Condensing)
Storage Temp.: -5 ~ 45
Timing Error: < 1%
Shell Material: PC +ABS ( Fireproof)
Wire Terminals: Wire 2 x 1.5 mm2 or 1 x 2.5 mm2
Current Load5A
BEFORE WIRING AND INSTALLING
3. Installer must be a trained, experienced service technician.
CAUTION
Electrical Shock or Equipment Damage Hazard. Can shock
individuals or short equipment circuitry.
WIRING
AC95~240V
IP20 NL
1234
M
Close Open 5
6
NTC
GA
L1 N1
LOAD
IP20 NL
1234
NTC
5
6
GB
IP20 NL
12345
6
NTC
GC
Dry Contact
A (RED)
Modbus
B (WHITE)
A (RED)
Modbus
B (WHITE)
A (RED)
Modbus
B (WHITE)
AC95~240V
AC95~240V
Note:
GA
GC is for water/gas boiler;
INSTALLATION
Step 1. Keep power off. See Fig 1.
Step 3. Connect power supply, load into the appropriate terminals.
(see “Wiring your thermostat” for details and Fig 3).
the box. See Fig 4.
During Power On
1. Power On/off: Press to turn the thermostat on/off.
2. Manual & Programmable
Touch M (mode) to change between manual mode and programme
In programmable mode, the period icon will show in the right side.
could not be
e user want to change, please go to
programmable mode.
In the mode of manual, press to set the desired temperature.
OPERATION
Touch the icon to set minute, hour and weekday (1 = Monday,
2 = Tuesday etc.) by using the arrows. Press once more to
confirm and exit.
Press and hold the for 5 seconds to lock/unlock your thermostat
lock or half lock.
5. Locking your Thermostat
7. Checking the Temperature of Floor Sensor
Press and hold the arrow for 5 seconds to display the temp. of
floor sensor.
accept the program schedule made via the APP on your device (see
your thermostat (NOT via your smartphone/tablet) simply follow the
thermostat and smartphone/tablet.
Touch M to change between manual mode and programme
In programme mode, touch and hold the icon
Press the icon
(2nd period).
Repeat this process for periods 3 4and 5 6.
Press the icon
(6 will show along the top of the screen).
Press the icon and use the and arrows to set the temp
Repeat the above process to set the period and temp. and Sunday
schedule.
Press once more to confirm and exit.
A separate schedule may be set for weekdays (Mon – Fri) and for
weekends (Sat or Sun).
Timedisplay WEEKDAY (MONDAY –FRIDAY)
(12345showsonscreen) WEEKEND(SATURDAY)
(6 showsonscreen)
TIME TEMPERATURE TIME TEMPERATURE
20°C
WEEKEND(SUNDAY)
(7showsonscreen)
TIME
TEMPERATURE
Saturday
C
P S
as below:
Period 5(1+2)
Period 6(3+4)
Period 3
Period 4
Period 2
Period 1 06:00
08:00
11:30
13:30
17:00
22:00
06:00
08:00
11:30
13:30
17:00
22:00
06:00
08:00
11:30
13:30
17:00
22:00
20 C
15 C
15 C
15 C
22 C
15 C
20 C
20 C
20 C
20 C
20 C
15 C
20 C
20 C
20 C
20 C
20 C
15 C
5. Creat thermostat group to Centralized control
6. Interated with Amazon Echo ,Google Home , Tmall Genie ,IFTTT.
8. No limit to add rooms and support Smart Scene.
8. Return To Factory Default
Press the Reatore Manufacturer Defaults, you can reset thermostat.
Steps:Open your app -go into your room - click menu on the top
right corner - move to the end - Press Restore Manufacturer Defaults.
During Power Off
When power is off, press and hold M
available
Then press M to scroll through
BHT-3000 Series Thermostat
For Water Heating/Boiler/Electric Heating
User Guide
DIMENSION
HOME SCREEN QUICK REFERENCE
Code Function Setting and options Default
1Temperature
compensation -7 to + 9 (for internal sensor) -1
2
3 Button locking 00: All buttons are locked except power button.
01: All buttons are locked. 01
4
5 Min. Set Temp. 5-15 05
6 Max. Set Temp. 15-45 35
7 00
8
Display Mode 00 Display both set temp. and room temp.
01 Display set temp. only
00
9
Sensor types AL
A
Standby Brightness 3-99
20
B
High temperature
protection setting. 25-70 45
0
C
Deadzone
Temperature 1 ~ 5
04
1
In Internal Sensor to control or limit the temp.
ExExternal Sensor to control or limit the temp.
AL Internal/ External Sensor Internal sensor to
control the temp., external sensor to limit the
temp.
Economy Mode 00: Non-energy saving Mode
01: Energy saving mode
Economy Temp. 0-30
Low temperature
protection setting. 0-10
Ou: Only external sensor
WIFI Type
Interlock
adjusted. If th manual mode or
and colorful icon
5
WI-FI CONNECTION
configure the
)1-1 giF( PPA ruoy daolnwoD 1 petS
t
ABOUT WIFI
devices
Step 3 Connect your Wi-Fi signal
On your thermostat
With power off, press and hold the arrow for eight (8) seconds.
The backlight will be on and the icon will flash one
Then, go back to the home page of your app
Press the
+
on the upper right corner of the page (see Fig 3-1-1) to add
your device. Click Confirm indicator rapidly blink (Fig 3-2) then select
your network and back to your app to enter the password of your
(Fig 3-4). This may typically take up to 5~90 seconds to complete.
Your room name could be edited when the device is connected (Fig 4-4).
app and your device. If your router doesn’t support it or your wifi
signal is weak or you can not connect by EZ mode, press the AP Mode
on the upper right corner in Fig 3-2.
On your thermostat
With power off, press and hold the arrow for eight (8) seconds.
The backlight will be on and the icon will flash one
Press and hold the arrow for eight (8) seconds again.
The icon will flash one
Then, go back to the home page of your app
Click Confirm indicator slowly blink (Fig 4-1) then select your network
and back to your app to enter the password of your wireless router
(Fig 3-3) and confirm. The app will go into the page in Fig 4-2.
If you have connected your thermostat successfully, please ignore
as below.
Press Connect now to select the wifi signal Smartlife-XXXX of your
thermostat Fig 4-3).
Go back to your app and click Connect now then the app will connect
This may typically take up to 5~90 seconds to complete.
Your room name could be edited when the device is connected (Fig 4-4).
Fig 4-1 Fig 4-2
Fig 4-3 Fig 4-4
PROGRAMMING YOUR THERMOSTAT
When your room is established successfully, it will display on the
is to turn on/off your room.
Click the line into begining programming your thermostat.
(at the
5-2) where you can simply click on the working days (Mon-Fri)
*
* Once your schedule has been set, click on SAVE and the app
will send the programming to your thermostat and confirm the
schedule has been saved.
(Fig 5-3)
(See Fig
*
adjust the temperature, the temperature will show in the centre
How to share your device with your family member?
ed in the above.
You can see the sharing account you have sent and the device you have
shared in this sharing page.
How to create a group?
in the red circle (Fig 5-2) then click Create Group
(Fig 6-1). Select all the rooms you want and confirm.
Fig 6-1 Fig 6-2
The one who create this group can control all the rooms at the same
Except create the group, in this menu page, you can also modify your
of your device.
Note
of your main page (Fig 6-2).
Select Device Sharing then add the account you want to share.
How to connect your device to Amazon Echo or Google Home
In your profile, click into the using page. Press Use Now > (Fig 7-1)
for your Amazon Echo or Google Home or Tmall Genie or IFTTT then
steps.
Fig 7-1
What is your Smart Scene and How to use it?
Customize your own personal scenes to suit your needs.For example,
home (Fig 7-2).Press
+
Air Quality,Sunrise/Sunset,Device)
Fig 7-2
Step 2: Add a task. Press
+
to Select Device (Power,Set Temp,Lock
Mode) to act, then Save.If you want to delete the scene,you can press
Delete in the end.
SIMPLE EXCEPTION HANDLING
No.Phenomenons Handling
1Power is onbut without display.*Check i he termi nals betweenLCD panel and
Power Unit Box is loosen.
2 Without output but displayworks. * Use a new LCD panel ornew Power Unit Box to
replace the oldone.
3RoomTemp. Is a li le differenrom
the actual.
*Dotemperature calibra on initem 1 oigh
senioropons
SERVICE
You don’t need to do anything if you are the one shared.
You can add as many as rooms you want.
NOTE: The room sound could be turned on/off in PROFILE-SETTING-
SOUND. The sound is matched with the default of your system .
and vice-versa.
degree.This temperature cannot be changed or adjusted.
in
turn off the device
Fig 2-3 Fig 2-4
Fig 3-1-1 Fig 3-2
Fig 3-3 Fig 3-4
Fig 5-2
Fig 5-3 Fig 5-4
Fig 2-1 Fig 2-2
Fig 5-1
My SmartThermostat
Nicole
Nicole
Nicole
Fig 1-1 Fig 1-2 IOS Fig 1-3 Android
For IOS devices, search for "Smart Life" in Apple Store and
download.
A(Fig 1-2).
For Android devices, search for "Smart Life" in Google Play and
download.
Step 2 Register your account
Open "Smart Life"
Click Allow to go into your page of register (Fig 2-2). Press register
and enter your phone no. or email (Fig 2-3) then you can get a
verificaon code. Input your password and confirm (Fig 2-4) to
complete your registeraon.If you have account, please log in.
Fig 3-1-2 Fig 3-1-3
Your thermostat carries an 24 months warranty from
date of purchase.Service outwith the warranty period
may incur a charge.More detail please contact with us
directly.
-
1
-
2
他の言語で
- English: MOES BHT-3000 Series User guide
その他のドキュメント
-
EXPERT4HOUSE BHT-006 Series ユーザーマニュアル
-
BECA BHT-8000 ユーザーガイド
-
EXPERT4HOUSE BHT-8000 ユーザーガイド
-
BECA BAC-008 Series ユーザーガイド
-
BECA BAC-006 Series ユーザーガイド
-
BECA BAC-1000 Series WiFi Thermostat ユーザーガイド
-
BECA BAC-003 Series ユーザーガイド
-
Meari Bell 19S ユーザーガイド
-
Danfoss GreenCon RC-C2/C4 room thermostat インストールガイド
-
Danfoss GreenCon RC-T2/T4 room thermostat インストールガイド
