Tektronix K420 取扱説明書

Instructions

K420

Bench Cart

070-8845-03

*P070884503*

070884503

www.tektronix.com

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

WARRANTY

Tektronix warrants that the products that it manufactures and sells will be free from defects in materials and workmanship

for a period of one (1) year from the date of shipment. If a product proves defective during this warranty period, Tektronix,

at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in

exchange for the defective product.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the

warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for

packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid.

Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the

Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any

other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate

maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting

from attempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair

damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction

caused by the use of non--Tektronix supplies; or d) to service a product that has been modified or integrated with other

products when the effect of such modification or integration increases the time or difficulty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED.

TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIXٛRESPONSIBILITY TO REPAIR OR REPLACE

DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR

BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT,

SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE

VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

K420 Bench Cart Instructions i

Table of Contents

General Safety Summary ii...................................

Contacting Tektronix iii.............................................

Introduction 1..............................................

Tools 1....................................................

Parts Identification 1........................................

Base Assembly 5............................................

Drawer Shelf and Drawer 11...................................

Tilt Shelf 15.................................................

Leg Caps 20.................................................

Nylon Straps 21..............................................

Customization 22............................................

Replaceable Parts 23..........................................

Specifications 24.............................................

25...................................

List of Figures

Figure 1: Identification of Small Parts 2........................

Figure 2: The K420 Bench Cart 4..............................

Figure 3: Preparing the Strut for Base Assembly 6................

Figure 4: Aligning the Leg Assemblies and the Strut 7.............

Figure 5: Installing the Casters 9..............................

Figure 6: Preparing the Drawer Shelf 11.........................

Figure 7: Aligning the Drawer Shelf 12..........................

Figure 8: Installing the Drawer 13..............................

Figure 9: Installing the Press--Stud Retainers 14...................

Figure 10: Preparing the Long Rails 15..........................

Figure 11: Long Rail Alignment Marks on the Leg Assemblies 16....

Figure 12: Preparing the Tilt Shelf with Handle 17................

Figure 13: Aligning the Tilt Shelf with Handle 17..................

Figure 14: Installation of Tilt Shelf Knobs 18.....................

Figure 15: Installing the Leg Caps 20............................

Figure 16: Installing the Nylon Straps with Buckles 21.............

ii K420 Bench Cart Instructions

General Safety Summary

Observe these safety precautions when using the K420 Bench Cart.

Keep the K420 Level

Keep the K420 level at all times, especially when it is loaded with instruments.

The cart is designed to be very stable, but it can fall over if tilted to extremes.

Observe this precaution especially in these cases:

HWhen rolling the cart across uneven floors.

HWhen rolling the cart through doorways with uneven thresholds.

HWhen lifting the cart wheels over cables.

HWhen rolling the cart up or down ramps.

Do Not Overload Shelves

Do not put more weight on any cart shelf than is listed in the specifications.

Load the top of the cart evenly.

Observe Electrical Safety

All parts of the cart must be treated as electrical conductors, even if they appear

to be nonconducting. Do not rely on the casters to provide insulation between the

cart and the surface it stands on. Conversely, do not rely on the casters to provide

a conductive ground path for the cart.

Test the Stability of Custom Configurations

Changes in shelf location and loading can affect the balance of the cart. If you

arrange the shelves differently from the configuration described in this manual,

test the cart carefully for stability before using it.

K420 Bench Cart Instructions iii

Preface

Contacting Tektronix

Phone 1-800-833-9200*

Address Tektronix, Inc.

Department or name (if known)

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

Web site www.tektronix.com

Sales support 1-800-833-9200, select option 1*

Service support 1-800-833-9200, select option 2*

Technical support Email: techsupport@tektronix.com

1-800-833-9200, select option 3*

6:00 a.m. -- 5:00 p.m. Pacific time

*This phone number is toll free in North America. After office hours, please leave a

voice mail message.

Outside North America, contact a Tektronix sales office or distributor; see the

Tektronix web site for a list of offices.

Preface

iv K420 Bench Cart Instructions

K420 Bench Cart Instructions 1

Introduction

The Tektronix K420 Bench Cart requires some assembly. This manual tells how

to assemble and use the cart.

You can assemble the K420 Bench Cart by yourself, but it is easier if you have

another person to help you.

You will need a large flat area to assemble the cart. The area should be level and

large enough to move the various parts into place. A carpeted floor space is ideal.

Tools

You will need a 3/4 inch (19 mm) open--end wrench, or an adjustable wrench that

can be adjusted to that size.

Other tools are included with the K420 Bench Cart. These include a 5/32 inch

Allen wrench, a 3/16 Allen wrench, a 1/8 inch Allen wrench, and a circular

bubble level.

Parts Identification

The large pieces of the K420 Bench Cart are packed separately in the shipping

carton. A bag of small parts is packed in a box with these instructions. The

included tools are also packed in this bag. Figure 1 on page 2 shows the small

parts you will be using.

Table 1 on page 3 lists all the parts needed to assemble the cart, including the

large pieces and assemblies. Take an inventory now to familiarize yourself with

the parts for the assembly process.

Introduction

2K420 Bench Cart Instructions

1/4-20 Cap Head Screw ,

1/2 inch length

1/2 inch Split Lockwasher

1/8inchAllenWrench

LongRail

Weld Nut

1/4-20 Shoulder Bolt,

1/2 inch length

Oval Knob

1/8 inch thick Kevlar

(plastic) Washer

1/4 inch Tooth Lockwasher

Circular Bubble Level

Press-Stud Retainer

3/4 inch Steel Washer

Press-On

Probe Holder

3/16 inch Allen Wrench

5/32 inch Allen Wrench

1/4-20 Set Screw

Figure 1: Identification of Small Parts

Introduction

K420 Bench Cart Instructions 3

Table 1: Parts List

Quantity Desscription

Large Parts

2Locking Casters

2Non--Locking Casters

1Tilt Shelf with handle

1Drawer Shelf

1Drawer

1Strut

2Leg assemblies

2Leg Caps

2Nylon Straps with buckles

Small Parts in Bag

41/2 inch Split Lockwashers

81/4--20 Cap Head Screws, 1/2 inch length

21/4--20 Shoulder Bolts, 1/2 inch length

2Oval Knobs

61/8 inch thick Kevlar (plastic) Washers

23/4 inch Steel Washers

81/4 inch Tooth Lockwashers

10 Weld Nuts

2Long Rails

21/4--20 Set Screws

2Press--Stud Retainers

1Press--On Probe Holder

Small Tools in Bag

13/16 inch Allen Wrench

15/32 inch Allen Wrench

11/8 inch Allen Wrench

1Circular Bubble Level

Introduction

4K420 Bench Cart Instructions

Locking Caster

Non-Locking Caster

Strut

Leg Assembly

Leg Cap

Tilt Shelf with handle

Drawer Shelf

Drawer

Front

Figure 2: The K420 Bench Cart

K420 Bench Cart Instructions 5

Base Assembly

Begin assembling the cart by joining the leg assemblies using the strut, and then

putting on the casters. You will use these parts:

H2 Locking Casters

H2Non--LockingCasters

H2 Extrusions

H2Legs

H4 Bumpons

H41/4--20x2inchScrews

H4 1 inch Fender Washers

H13/16HexKey

H41x3inchEndCaps

H1Strut

H4 1/2 inch Split Lockwashers

H4 1/4 20 Cap Head Screws, 1/2 inch length

H4 1/4 inch Tooth Lockwashers

H4WeldNuts

You will use a 3/4 inch (19 mm) wrench or adjustable wrench, and the 3/16 inch

Allen wrench included with your cart.

1. Prepare the strut as shown in Figure 3. Position the weld nut with the raised

threaded flange toward the strut. Leave each screw assembly loose; do not

screw the weld nut onto the cap head screw more than one full turn.

Base Assembly

6K420 Bench Cart Instructions

Front

Weld Nut

1/4 inch Tooth Lockwasher

1/4-20 Cap Head Screw

Figure 3: Preparing the Strut for Base Assembly

2. On each leg assembly, observe that there is a small, clear, plastic button on

the horizontal leg bar. This button is on the inside of the cart, at the back.

Position the leg assemblies as shown in Figure 4. Leave a space between the

leg assemblies about equal to the length of the strut.

Base Assembly

K420 Bench Cart Instructions 7

Pencil Marks: first line should be 10 inches

from the bottom of the extrusion. For the first

leg assembly, turn extrusion so pencil marks

are on the inside. For second leg assembly,

pencil marks are also on the inside.

Bumpons are on the

inside of the extrusions.

Note: Leg tube can be crushed if screw is over

tightened; maximum torque is 3-6 foot/pounds.

Clear Plastic Buttons (1 on each leg assembly)

Figure 4: Aligning the Leg Assemblies and the Strut

3. Orient extrusion so the end with threaded holes is on the bottom If shelf

position pencil marks are present on one of the slotted sides of the extrusion

there should be one mark 13 inches from this end. You will build two leg

assemblies.

4. Place long screw through washer and insert through bottom of leg tube (side

with large caster nuts) and into the extrusion. Screw will extend through top

of leg tube to receive threaded ends of extrusion. Hand tighten with hex key.

Base Assembly

8K420 Bench Cart Instructions

CAUTION. Leg tube can be crushed if screw is over tightened.

Max torque is 3--6 ft--lbs. Repeat for second assembly.

5. Apply two bumpons to the top of each leg as shown in the illustration. They

go on the side of the extrusion with pencil marks for each assembly.

6. Install end caps into end of each leg. Don’t install end caps into extrusions.

7. Position the strut horizontally between the leg assemblies, as shown in

Figure 4, with the open side of the strut to the back. Line up the weld nuts

with the back groove in the leg assemblies.

8. Slide the strut down to the base of the cart, adjusting the distance between

the leg assemblies as needed. When complete, make sure the strut is resting

tight against the clear plastic buttons on the leg assemblies.

9. Use the 3/16 inch Allen wrench to tighten the cap head screws. Tighten them

first snugly, then go back and tighten them firmly.

NOTE. If you have a torque wrench available, tighten these and all shelf screws

to 60 in.... lb (6.8 N.... m) torque.

10. Tip the cart onto its back as shown in Figure 5, resting it on the work surface

by the tops and backs of the leg assemblies.

11. Identify which casters are locking and which are non--locking. The locking

casters, which go on the front of the cart, have an extra tab that you step on

to lock the wheels.

Base Assembly

K420 Bench Cart Instructions 9

Front

Locking

Casters

1/2inch Split

Lockwashers

Non-

Locking

Casters

Figure 5: Installing the Casters

12. On the locking casters, place a 1/2 inch split lockwasher on each threaded

shaft, then install the casters into the two front holes in the bottoms of the

leg assemblies. Tighten the casters only until they are snug using the 3/4

inch (19 mm) wrench.

13. On the non--locking casters, place a 1/2 inch split lockwasher on each

threaded shaft, then install the casters into the two back holes in the bottoms

of the leg assemblies. Tighten the casters only until they are snug.

14. Return the cart to the upright position.

Base Assembly

10 K420 Bench Cart Instructions

K420 Bench Cart Instructions 11

Drawer Shelf and Drawer

Install a drawer shelf and drawer in the cart. You will use these parts:

H1DrawerShelf

H1Drawer

H4 1/4 20 Cap Head Screws, 1/2 inch length

H4 1/4 inch Tooth Lockwashers

H4WeldNuts

H2 Press--Stud Retainers

You will use the 3/16 inch Allen wrench and the circular bubble level included

with your cart.

1. Prepare the drawer shelf as shown in Figure 6 by installing a cap head screw,

a tooth lockwasher, and a weld nut in each of the four side holes of the shelf.

Leave each screw assembly loose; do not screw the weld nut onto the cap

head screw more than one full turn.

WeldNut

1/4 inch Tooth Lockwasher

1/4- 20 Cap Head Screw

Figure 6: Preparing the Drawer Shelf

Drawer Shelf and Drawer

12 K420 Bench Cart Instructions

2. Position the drawer shelf horizontally between the leg assemblies, as shown

in Figure 7. Position the shelf so the open edge is to the front of the cart.

Front

Figure 7: Aligning the Drawer Shelf

3. Slide the drawer shelf down to into the position shown in Figure 8. (A light

pencil line has been marked on the insides of the leg assemblies at this

position.) Slide the drawer shelf slowly between the leg assemblies to avoid

scratching the paint. Use the circular bubble level to make sure the shelf is

level.

ページを読み込んでいます...

Tektronix K420 取扱説明書

関連論文

その他の書類