Tektronix K4000 取扱説明書

Instructions

K4000

TransportCart

071-0833-01

*P071083301*

071083301

www.tektronix.com

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

WARRANTY

Tektronix warrants that the products that it manufactures and sells will be free from defects in materials and workmanship

for a period of one (1) year from the date of shipment. If a product proves defective during this warranty period, Tektronix,

at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in

exchange for the defective product.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the

warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for

packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid.

Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the

Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any

other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate

maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting

from attempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair

damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction

caused by the use of non--Tektronix supplies; or d) to service a product that has been modified or integrated with other

products when the effect of such modification or integration increases the time or difficulty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED.

TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIXٛRESPONSIBILITY TO REPAIR OR REPLACE

DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR

BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT,

SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE

VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

K4000 Transport Cart Instructions i

Table of Contents

General Safety Summary iii...................................

Contacting Tektronix iv.............................................

Introduction 1..............................................

Tools 1..........................................................

Parts Identification 1...............................................

Base Assembly 5............................................

Bottom Shelf 9..............................................

Keyboard Shelf 11...........................................

Top Shelf 14.................................................

Drawer 16..................................................

Skyhook 18.................................................

Nylon Straps 20..............................................

Leg Caps 21.................................................

Stop Bar 22.................................................

Monitor Clamps 23...........................................

Instrument Mounts 24........................................

Customization 26............................................

Replaceable Parts 27..........................................

Specifications 28.............................................

29...................................

Table of Contents

ii K4000 Transport Cart Instructions

List of Figures

Figure 1: Identification of Small Parts 2........................

Figure 2: The K4000 Transport Cart 4..........................

Figure 3: Preparing the Strut for Base Assembly 6................

Figure 4: Aligning the Leg Assemblies and the Strut 8.............

Figure 5: Installing the Casters 9..............................

Figure 6: Preparing the Bottom Shelf 10.........................

Figure 7: Aligning the Bottom Shelf 11..........................

Figure 8: Preparing the Keyboard Shelf 12.......................

Figure 9: Aligning the Keyboard Shelf 14........................

Figure 10: Preparing the Top Shelf 15...........................

Figure 11: Aligning the Top Shelf 16.............................

Figure 12: Installing the Drawer 17.............................

Figure 13: Installing the Press Stud Retainers 18..................

Figure 14: Installing the Skyhook 20............................

Figure 15: Installing the Nylon Straps with Buckles 21.............

Figure 16: Installing the Leg Caps 22............................

Figure 17: Installing the Stop Bar 23............................

Figure 18: Installing the Monitor Clamps 24......................

Figure 19: Installing the Instrument M ounts 26..................

K4000 Transport Cart Instructions iii

General Safety Summary

Observe these safety precautions when using the K4000 Transport Cart.

Keep the K4000 Level

Keep the K4000 level at all times, especially when it is loaded with instruments.

The cart is designed to be very stable, but it can fall over if tilted to extremes.

Observe this precaution especially in these cases:

HWhen rolling the cart across uneven floors.

HWhen rolling the cart through doorways with uneven thresholds.

HWhen lifting the cart wheels over cables.

HWhen rolling the cart up or down ramps.

Do Not Overload Shelves

Do not put more weight on any cart shelf than is listed in the specifications.

Load the top of the cart evenly.

Observe Electrical Safety

All parts of the cart must be treated as electrical conductors, even if they appear

to be nonconducting. Do not rely on the casters to provide insulation between the

cart and the surface it stands on. Conversely, do not rely on the casters to provide

a conductive ground path for the cart.

Test the Stability of Custom Configurations

Changes in shelf location and loading can affect the balance of the cart. If you

arrange the shelves differently from the configuration described in this manual,

test the cart carefully for stability before using it.

iv K4000 Transport Cart Instructions

Preface

Contacting Tektronix

Phone 1-800-833-9200*

Address Tektronix, Inc.

Department or name (if known)

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

Web site www.tektronix.com

Sales support 1-800-833-9200, select option 1*

Service support 1-800-833-9200, select option 2*

Technical support Email: techsupport@tektronix.com

1-800-833-9200, select option 3*

6:00 a.m. -- 5:00 p.m. Pacific time

*This phone number is toll free in North America. After office hours, please leave a

voice mail message.

Outside North America, contact a Tektronix sales office or distributor; see the

Tektronix web site for a list of offices.

K4000 Transport Cart Instructions 1

Introduction

The Tektronix K4000 Transport Cart requires some assembly. This manual tells

how to assemble and use the cart.

You can assemble the K4000 Transport Cart by yourself, but it is easier if you

have another person to help you.

You will need a large flat area to assemble the cart. The area should be level and

large enough to move the various parts into place. A carpeted floor space is ideal.

Assembly will require approximately 2 hours.

Tools

You will need a 3/4 inch (19 mm) open--end wrench, or an adjustable wrench that

can be adjusted to that size.

Other tools are included with the K4000 Transport Cart. These include a 3/16

inch Allen wrench and a circular bubble level.

Parts Identification

The large pieces of the K4000 Transport Cart are packed separately in the

shipping carton. A bag of small parts is packed in a box with thes casters and

other small parts. The included tools are also packed in this bag. Figure 1 on

page 2 shows the small parts you will be using.

Table 1 on page 3 lists all the parts needed to assemble the cart, including the

large pieces and assemblies. Take an inventory now to familiarize yourself with

the parts for the assembly process.

Introduction

2K4000 Transport Cart Instructions

Press On Probe Holder

Figure 1: Identification of Small Parts

Introduction

K4000 Transport Cart Instructions 3

Table 1: Parts List

Quantity Desscription

Large Parts

2Locking Casters

2Non--Locking Casters

1Top Shelf

1Keyboard Shelf

1Bottom Shelf

1Drawer

1Strut

2Leg assemblies

2Upright Caps

4Nylon Straps with buckles

1Skyhook

1Skyhook Mount

1Skyhook Adjustment Knob

1Skyhook Sleeve

1Stop Bar

4Monitor Clamps

2Instrument Mounts

4End C aps

Small Parts in Bag

41/2 inch Split Lockwashers

22 1/4--20 x 1/2 inch Cap Head Screws

22 1/4 inch Tooth Lockwashers

22 Weld Nuts

2Press--Stud Retainers

6#8--32 Wing Nuts

41/4--20 x 1--1/4 inch Cap Head Screws

41 inch Fender Washers

1Press On Probe Holder

Small Tools in Bag

13/16 inch Allen Wrench

1Circular Bubble Level

Introduction

4K4000 Transport Cart Instructions

Figure 2: The K4000 Transport Cart

K4000 Transport Cart Instructions 5

Base Assembly

Begin assembling the cart by joining the leg assemblies using the strut, and then

putting on the casters. You will use these parts:

H2 Locking Casters

H2Non--LockingCasters

H2 Uprights

H2Legs

H4 End Caps

H1Strut

H4 1/2 inch Split Lockwashers

H4 1/4 20 Cap Head Screws, 1/2 inch length

H4 1/4 inch Tooth Lockwashers

H4 1/4 20 Cap Head Screws, 1--1/4 inch length

H4 1 inch Fender Washers

H4WeldNuts

H4 Bumpons

You will use a 3/4 inch (19 mm) wrench or adjustable wrench, and the 3/16 inch

Allen wrench included with your cart.

1. Prepare the strut as shown in Figure 3. Position the weld nut with the raised

threaded flange toward the strut. Leave each screw assembly loose; do not

screw the weld nut onto the cap head screw more than one full turn.

Base Assembly

6K4000 Transport Cart Instructions

Front

Weld Nut

1/4 inch Tooth Lockwasher

1/4-20 Cap Head Screw

Figure 3: Preparing the Strut for Base Assembly

2. Attach legs to the upright using the 1/4--20 x 1--1/4 inch cap head screws and

the 1 inch fender washers provided. Place the endcaps in the ends of th elegs

and press in using firm pressure.

NOTE. Position each leg so that the two large holes face down when attaching

legs to uprights.

3. Place four bumpons in--line as indicated by Figure 4. Two of the bumpons

are placed on the inside top surface of each leg and in--line with the back

groove. The remaining two bumpons are placed on top of the strut in--line

with the back groove.

Base Assembly

K4000 Transport Cart Instructions 7

Pencil Marks: first line should be 10 inches

from the bottom of the extrusion. For the first

leg assembly, turn extrusion so pencil marks

are on the inside. For second leg assembly,

pencil marks are also on the inside.

Bumpons are on the

inside of the extrusions.

Note: Leg tube can be crushed if screw is over

tightened; maximum torque is 3-6 foot/pounds.

Clear Plastic Buttons (1 on each leg assembly)

Figure 4: Aligning the Leg Assemblies and the Strut

4. Position the strut horizontally between the leg assemblies, as shown in

Figure 4, with the open side of the strut to the back. Line up the weld nuts

with the back grooves of each upright. Slide the strut down to the base of the

cart, adjusting the distance between the leg assemblies as needed. When

complete, make sure the strut is resting tight against the bumpons placed on

the legs.

5. Use the 3/16 inch Allen wrench to tighten the cap head screws. Tighten them

first snugly, then go back and tighten them firmly.

Base Assembly

8K4000 Transport Cart Instructions

NOTE. If you have a torque wrench available, tighten these and all shelf screws

to 60 in.... lb (6.8 N.... m) torque.

6. Tip the cart onto its back as shown in Figure 5, resting it on the work surface

by the tops and backs of the leg assemblies.

7. Identify which casters are locking and which are non--locking. The locking

casters, which go on the front of the cart, have an extra tab that you step on

to lock the wheels.

Front

Locking

Casters

1/2inch Split

Lockwashers

Non-

Locking

Casters

Figure 5: Installing the Casters

8. On the locking casters, place a 1/2 inch split lockwasher on each threaded

shaft, then install the casters into the two front holes in the bottoms of the

leg assemblies. Tighten the casters only until they are snug using the 3/4

inch (19 mm) wrench.

9. On the non--locking casters, place a 1/2 inch split lockwasher on each

threaded shaft, then install the casters into the two back holes in the bottoms

of the leg assemblies. Tighten the casters only until they are snug.

10. Return the cart to the upright position.

K4000 Transport Cart Instructions 9

Bottom Shelf

Installing the bottom shelf. You will use these parts:

H1 Bottom Shelf

H4 1/4 20 Cap Head Screws, 1/2 inch length

H4 1/4 inch Tooth Lockwashers

H4WeldNuts

You will use the 3/16 inch Allen wrench and the circular bubble level included

with your cart.

1. Prepare the bottom shelf as shown in Figure 6 by installing a cap head screw,

a tooth lockwasher, and a weld nut in each of the four side holes of the shelf.

Leave each screw assembly loose; do not screw the weld nut onto the cap

head screw more than one full turn.

Figure 6: Preparing the Bottom Shelf

2. Position the bottom shelf horizontally between the leg assemblies, as shown

in Figure 7. Ensure that the cable tie hole pattern is facing the rear of the

cart.

Bottom Shelf

10 K4000 Transport Cart Instructions

Figure 7: Aligning the Bottom Shelf

3. Slide the bottom shelf down to into position. A light pencil line has been

marked on the insides of the leg assemblies at this position. Slide the bottom

shelf slowly between the leg assemblies to avoid scratching the paint. Use

the circular bubble level to make sure the shelf is level.

If you have another person helping you, that person can hold the shelf at the

proper height as you tighten the screws. If you are assembling the cart by

yourself, tighten each screw in turn just enough to hold, and then adjust the

heights one by one until the shelf is positioned properly.

4. Use the 3/16 inch Allen wrench to tighten the cap head screws. Tighten them

first snugly, then go back and tighten them firmly.

K4000 Transport Cart Instructions 11

Keyboard Shelf

Installing the keyboard shelf. You will use these parts:

H1 Keyboard Shelf

H8 1/4 20 Cap Head Screws, 1/2 inch length

H8 1/4 inch Tooth Lockwashers

H8WeldNuts

You will use the 3/16 inch Allen wrench and the circular bubble level included

with your cart.

1. Prepare the keyboard shelf as shown in Figure 8 by installing a cap head

screw, a tooth lockwasher, and a weld nut in each of the eight side holes of

the shelf. Leave each screw assembly loose; do not screw the weld nut onto

the cap head screw more than one full turn.

Figure 8: Preparing the Keyboard Shelf

Keyboard Shelf

12 K4000 Transport Cart Instructions

2. Position the keyboard shelf horizontally between the leg assemblies, as

shown in Figure 9. Position the shelf so that the long end of the shelf is

positioned to the front of the cart.

3. Slide the keyboard shelf down to into position. (A light pencil line has been

marked on the insides of the leg assemblies at the keyboard shelf position.)

Slide the keyboard shelf slowly between the leg assemblies to avoid

scratching the paint. Use the circular bubble level to make sure the shelf is

level.

If you have another person helping you, that person can hold the shelf at the

proper height as you tighten the screws. If you are assembling the cart by

yourself, tighten each screw in turn just enough to hold, and then adjust the

heights one by one until the shelf is positioned properly.

4. Use the 3/16 inch Allen wrench to tighten the cap head screws. Tighten them

first snugly, then go back and tighten them firmly.

ページを読み込んでいます...

Tektronix K4000 取扱説明書

関連論文

その他の書類