USB Video Conferencing Endpoint
Quick Start Guide(V1.1)
www.yealink.com
English | 简体中文
UVC40
1
AAA Battery×2UVC 40
VCR20
Remote Control
Cable Tie×5
Quick Start Guide
We recommend that you use the accessories provided or approved by Yealink. The use of
unapproved third-party accessories may result in reduced performance.
Use the Yealink original power adapter (48V/0.7A) to charge the endpoint only. The use of the
third-party power adapter may cause the damage to the endpoint.
The USB cable in the MVC400/ZVC400 package is 2.5 meters long.
Mounting Bracket
and Accessories
Power Adapter
×4
×2
×2
Silicone Pad×2
Put on a Flat Surface
Package Contents
7m
USB Cable
TV TV
UVC40 Installation
2
Wall Mounting
Use the bracket to mount your endpoint on a wall. The mounting height affects your
camera view. The recommended height is 1.1m above the ground.
Placing UVC40
Mount the UVC40 below the TV when
the mounting height of the TV is higher than
120cm.
Mount the UVC40 above the TV when
the mounting height of the TV is lower
than 120cm.
Step1：Assemble the mounting bracket
Mount on a Wall
TV
10cm
TV
H>120cm
H<120cm
3
Hole depth: 30mm
Hole diameter: 6mm
118mm
T4×30 screws
15°
15°
Step2：Mount the UVC40 to the wall
Adjusting the Camera Tilt
3
4
5
4
Remote Control Installation Cable Ties Installation
Remote Control and Cable Ties Installation
Hardware Interface Instructions
1
2
4
3
Line In: connect a 3.5mm audio connector to use the UVC40 as an audio output device.
USB: insert DD10 to connect to CPW90 if needed.
Video Out: connect to a PC as video output.
Microphone: connect to the microphone (for exmaple, VCM34).
DC48V: connect to the power adapter.
Reset: reset the UVC40 to factory defaults.
Security slot: connect a universal security cable to the UVC40 so that you can
lock the UVC40 down.
5
6
7
1
2 3 4 5 6 7 8
8
Pairing key: press the pairing key to pair the CPW90 wireless microphone.
5
UVC40 Connection
LED Indicator Instructions
LED indicators on the UVC40:
LED Status
Description
Off
Flashing green
The UVC40 is not properly connected to the mini-PC.
Solid green
Flashing orange The UVC40 is upgrading firmware.
There is an incoming call.
The UVC40 is in recovery mode and the firmware has not been
upgraded.
The UVC40 is active.
Flashing red
Solid red The UVC40 is muted.
Flashing red and
green alternately
The UVC40 is paired with the CPW90.
The UVC40 is initializing or in sleep mode.Solid orange
The cable should be replaced at once if its skin is broken.
The priority of audio input channel isMicrophone(VCM34) >USB(CPW90).
USB cable
Cat5e
Microphone
UVC40
6
VCR20遥控器 7号电池x2UVC40 7米USB线
束线带x5
此为A级产品。在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰采取
切实可行的措施。
我们推荐使用由Yealink提供或经Yealink认可的配件和线缆，使用未经认可的第三方配件和线缆可能会
导致性能的下降。
使用HDMI线前，请套上磁环用于抗电磁干扰。
MVC400/ZVC400产品组合包中标配的USB线长为2.5米。
UVC40
快速入门指南
支架配件
（用于安装主机）
电源适配器
×4
×2
×2
硅胶垫x2
平放安装
包装清单
安装UVC40
TV TV
7
放置UVC40
螺丝规格：T4×30
打孔直径： 6mm
打孔深度： 30mm
118mm
步骤1：安装支架
步骤2：墙装
当电视高度高于120cm时，终端安装
在电视下方。
墙装
当电视高度低于120cm时，终端安装
在电视上方。
使用支架将终端安装在墙上。 安装高度会影响你的视野，建议的高度为离地面1.1m。
墙装
TV
10cm
TV
H>120cm
H<120cm
8
调整倾斜角度
15°
15°
3
4
5
9
安装遥控器和束线带
安装遥控器电池 安装束线带
1
2
4
3
5
6
7
音频线性输入: 连接3.5mm音频接头，将UVC40作为音频输出设备。
视频输出: 连接电脑作为视频输出。
USB: 可插入BT42，搭配CPW90-BT蓝牙麦使用。
麦克风： 连接麦克风（例如：VCM34）。
电源接口: 连接电源适配器。
重置键：重置设备到出厂设置。
安全锁孔 : 将主机锁在固定位置。
硬件接口介绍
8
配对键： 按配对键，进入配对蓝牙麦状态。
1
2 3 4 5 6 7 8
10
连接UVC40
音频输入通道优先级顺序：麦克风（VCM34）>USB（CPW90-BT）。
如果使用过程中发现线缆破皮，请立即更换。
更多关于如何使用CPW90-BT蓝牙无线麦，请参阅
Yealink CPW90-BT Bluetooth Wireless Microphones Quick Start Guide(CN, EN)。
UVC40固件更新中。
UVC40 指示灯介绍如下:
绿灯闪烁
红灯常亮
指示灯介绍
关闭
指示灯状态 说明
UVC40没有正确连接到mini-PC上或未处于正常工作状态。
来电中状态。
绿灯常亮 UVC40处于工作中状态。
红灯闪烁 UVC40进入恢复模式，还未固件更新。
UVC40处于静音状态。
红绿灯交替 UVC40和CPW90-BT配对状态。
橙色灯常亮 UVC40启动或等待状态。
橙色灯闪烁
USB线
Cat5e网线
Microphone
UVC40
Regulatory Notices
About Yealink
Technical Support
Visit Yealink WIKI (http://support.yealink.com/) for the latest firmware, guides, FAQ, Product documents, and more. For better service,
we sincerely recommend you to use Yealink Ticketing system (https://ticket.yealink.com) to submit all your technical issues.
Yealink is a global leading provider of enterprise communication and collaboration solutions, offering video conferencing service to
worldwide enterprises. Focusing on research and development, Yealink also insists on innovation and creation. With the outstanding
technical patents of cloud computing, audio, video and image processing technology, Yealink has built up a panoramic collaboration
solution of audio and video conferencing by merging its cloud services with a series of endpoints products. As one of the best
providers in more than 140 countries and regions including the US, the UK and Australia, Yealink ranks No.1 in the global market
share of SIP phones shipments.
Operating Ambient Temperatures
Operating temperature: +32 to 104°F (0 to 40°C)
Relative humidity: 5% to 90%, noncondensing
Storage temperature: -22 to +160°F (-30 to +70°C)
Warranty
Our product warranty is limited only to the unit itself, when used normally
in accordance with the operating instructions and the system environment.
We are not liable for damage or loss resulting from the use of this product,
or for any claim from a third party. We are not liable for problems with
Yealink device arising from the use of this product; we are not liable for
financial damages, lost profits, claims from third parties, etc., arising from
the use of this product.
Explanation of the symbols
DC symbol
is the DC voltage symbol.
WEEE Warning symbol
To avoid the potential effects on the environment and human health
as a result of the presence of hazardous substances in electrical and
electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin
symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
Restriction of Hazardous Substances Directive (RoHS)
This device complies with the requirements of the EU RoHS Directive.
Statements of compliance can be obtained by contacting [email protected].
Safety Instructions
Save these instructions. Read these safety instructions before use!
General Requirements
Before you install and use the device, read the safety instructions
carefully and observe the situation during operation.
During the process of storage, transportation, and operation, please
always keep the device dry and clean, avoid collision and crash.
Please attempt not to dismantle the device by yourself. In case of any
discrepancy, please contact the appointed maintenance center for repair.
Please refer to the relevant laws and statutes while using the device.
Legal rights of others should be respected as well.
Environmental Requirements
Place the device at a well-ventilated place. Do not expose the device
under direct sunlight.
Keep the device dry and free of dusts.
Do not place the device on or near any inflammable or fire-vulnerable
object, such as rubber-made materials.
Keep the device away from any heat source or bare fire, such as a candle
or an electric heater.
Operating Requirements
Do not let a child operate the device without guidance.
Do not let a child play with the device or any accessory in case of
accidental swallowing.
Please use the accessories provided or authorized by the manufacturer
only.
The power supply of the device shall meet the requirements of the input
voltage of the device. Please use the provided surge protection power
socket only.
Before plugging or unplugging any cable, make sure that your hands are
completely dry.
Do not spill liquid of any kind on the product or use the equipment near
water, for example, near a bathtub, washbowl, kitchen sink, wet
basement or near a swimming pool.
During a thunderstorm, stop using the device and disconnect it from the
power supply. Unplug the power plug and the Asymmetric Digital
Subscriber Line (ADSL) twisted pair (the radio frequency cable) to avoid
lightning strike.
If the device is left unused for a rather long time, disconnect it from the
power supply and unplug the power plug.
When there is smoke emitted from the device, or some abnormal noise
or smell, disconnect the device from the power supply, and unplug the
power plug immediately.
Contact the specified maintenance center for repair.
Do not insert any object into equipment slots that is not part of the
product or auxiliary product.
Before connecting a cable, connect the grounding cable of the device
first. Do not disconnect the grounding cable until you disconnect all other
cables.
Cleaning Requirements
Before cleaning the device, disconnect it from the power supply.
Use a piece of soft, dry and anti-static cloth to clean the device.
Keep the power plug clean and dry.
Troubleshooting
The unit cannot supply power to device other than Yealink device.
There is a bad connection with the plug.
1. Clean the plug with a dry cloth.
2. Connect it to another wall outlet.
The usage environment is out of operating temperature range.
1. Use in the operating temperature range.
The cable between the unit and the Yealink device is connected incorrectly.
1. Connect the cable correctly.
You cannot connect the cable properly.
1. You may have connected a wrong Yealink device.
2. Use the correct power supply.
Some dust, etc., may be in the port.
1. Clean the port.
Contact your dealer or authorized service facility for any further questions.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following
two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
IC Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) this device may not cause interference; and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device. CAN ICES-3(B)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.NMB-3(B)
Radiation Exposure Statement
This equipment complies with FCC and IC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps
qu'aucune autre antenne ou émetteur. Cet équipement devrait être installé et
actionné avec une distance minimum de 20 centimètres entre le radiateur et
votre corps.
Contact Information
YEALINK NETWORK TECHNOLOGY CO.,LTD.
309, 3rd Floor, No.16, Yun Ding North Road, Huli District, Xiamen City, Fujian, P.R. C
YEALINK (EUROPE) NETWORK TECHNOLOGY B.V.
Strawinskylaan 3127, Atrium Building, 8th floor, 1077ZX Amsterdam, The Netherlands
YEALINK (USA) NETWORK TECHNOLOGY CO., LTD.
999 Peachtree Street Suite 2300, Fulton, Atlanta, GA, 30309, USA
Made in China
YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD.
Web: www.yealink.com
Copyright
©2020 YEALINK(XIAMEN) NETWORK
TECHNOLOGY CO.,LTD
.All rights reserved.
430104001347
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Yealink Yealink UVC40 (EN, CN) V1.1 クイックスタートガイド
- タイプ
- クイックスタートガイド
他の言語で
関連論文
-
Yealink Yealink MVC400 for Microsoft Teams Rooms System (EN, CN) V1.0 クイックスタートガイド
-
-
-
Yealink RingCentral A20 ユーザーガイド
-
Yealink CPW90-BT Bluetooth Wireless Microphones 中英 V1.2 クイックスタートガイド
-
-
-
-
-