Niigata seiki DMS-AE, DMS-D ユーザーマニュアル

  • こんにちは!このNiigata Seiki DMS-AE、DMS-Dデュロメータスタンドの取扱説明書について、ご質問にお答えします。この説明書では、製品の各部の名称と機能、安全上の注意、使用方法、メンテナンス方法などが記載されています。お気軽にご質問ください。
  • デュロメータスタンドを使用する際の環境条件は?
    デュロメータの取り付け方法は?
    試験台の傾きを調整するには?
    使用後のメンテナンスは?
DUROMETER
TYPE-A
0
50
90
80 20
70 30
10
60 40
DUROMETER
TYPE-A
0
50
90
80 20
70 30
10
60 40
Throughout this manual, this mark :
indicates a requirement, you MUST follow.
Weight provides consistent measuring force.
Handle for lowering Durometer to Test
Sample.
Supports Weight. Please keep in proper
adjustment.
With Gauge mounted, can be moved up
and down.
Platform for holding Test Sample.
Screws for adjusting Test Sample tilt.
Supports Test Stand.
Tighten to secure the Bracket to the Post.
Mounting for Durometer at bottom, supports
Weight at top.
Support the Bracket.
Holds the Weight to the Rod. Please keep
tight and check periodically.
Please use care and protect the Test
Platform from falling parts when working
with the Rod assembly.
Safety stop to prevent the Bracket from
falling.
Do not use to support Bracket; please make
sure Bracket Clamp is tight when
positioning Bracket.
Weight
Handle
Weight Stop Nut
Bracket
Test Platform
Adjustment Screws
Base
Bracket Clamp
Rod
Post
Rod Screw
Stop Ring
DMS-D only
DUROMETER STAND
Hardness Tester - Measuring Jig DMS-AE DMS-D
Model No.
INSTRUCTION MANUAL
Thank you for purchasing the Durometer Stand. Stand provides a constant measuring force when used with separately
available Durometer to measure the hardness of plastic or rubber.
For safe and proper operation, please read this instruction manual thoroughly
before use and follow the procedures described. Please keep manual where it is
accessible to user for future reference.
Keep this manual with the instrument if transferred or leased to a third party.
For inquiries about our products, please contact dealer or place of purchase.
SAFETY NOTICE
PART IDENTIFICATION FUNCTION
Base
Rod
Post
Handle
Weight
Rod Screw
Test Platform
Bracket
Weight Stop Nut
Adjustment
Screws
Bracket
Clamp
Model DMS-AE shown
(Opposite Side)
SAFETY PRECAUTIONS Please Observe
Always follow the proper operating procedures in order to prevent harm to yourself or others, and to prevent damage to property.
Improper use may cause injury or property damage.
Read the instruction manual and follow the
instructions.
Use of product other than as described in the manual
may cause accident.
Use only as directed.
This stand is to be used with separately available
Durometer as measurement jig for applying constant
pressure when measuring hardness of plastic and rubber.
Modification of product, or use other than as indicated
will result in poor accuracy, component wear or damage,
accident, or other unpredictable result.
Use in an environment which meets the following
conditions:
Dry location protected from rain, water, and oils.
Location not subject to wide temperature changes.
Location free from cutting chips and dust.
Horizontal surface which is stable and free fromvibration.
Location protected from use by children and
unauthorized personnel.
Use in location contrary to the above may cause poor accuracy,
damage to the product, or may result in accident or injury.
CAUTION
Product only to be used with durometer models
listed under Specifications section at end of
manual.
Weight is designed so that total weight will comply with
JIS K6253 when used with specified durometer.
Use of non-specified durometer will not be compliant
with JIS standard.
Handle With Care.
Do not drop or subject to shock - instrument accuracy
may be affected.
Insure hat Bracket Clamp is securely tightened.
If Bracket Clamp is loose, measuring instrument may
drop causing damage or injury. Loose clamp will also
cause poor accuracy, damage, or malfunction.
Follow instructions to apply rust preventive
treatment after use.
Please refer to After Use Care, Storage section to
protect product from corrosion.
Thumb Rest
(Cap)
Test
Sample
Rod
Bracket
Test Platform
Durometer
Mounting the Durometer
Test Platform Slope Adjustment
SPECIFICATIONS
Materials
Post, Weight Iron
Base Cast Iron
Test PlatformGlass
Compatible Durometer
ADM-A, ADM-E
ADM-D
Model No.
DMS-AE
DMS-D
Weight
7.3kg
11.4kg
Clean Test Platform with a soft, dry cloth moistened with alcohol.
Do not clean with abrasive or stiff brush, as it will cause scratches and result in poor accuracy.
Apply rust preventive oil to the Post and Weight.
The Post and Weight are subject to corrosion, so please keep coated with oil and keep in low humidity environment.
AFTER USE CARE, STORAGE NOTES
Remove
1
Slowly Push Down
Adjust
Hold Here
While In Contact
Install
While securely supporting the Bracket, loosen the
Bracket Clamp and move it up before re-tightening the
clamp.
For model DMS-D, adjust Stop Ring if required before
loosening and adjusting the Bracket.
Unscrew and remove the Thumb Rest from the
Durometer.
Insert the exposed thread of the Durometer into the
hole at the bottom of the Rod and rotate to attach.
(Make sure the Rod does not rotate while screwing on
the durometer by holding the Rod with your hand.)
While securely supporting the Bracket, loosen the Bracket
Clamp and adjust the height. The Duromter Indenter should be
close to the Test Platform without touching. When at proper
height, secure by tightening the Bracket Clamp.
Lower the Handle to move the Durometer into contact with the
Test Platform.
When Handle is fully depressed, do not apply additional force as this
may cause damage to the instrument.
Monitor the Durometer Pointer as follows:
With Handle down, adjust the two Platform Adjustment
Screws to adjust tilt until Pointer is within 1.
Reading within 100 1OK
Reading more than 100 1See step
Operation
Place the Test Sample on the Test Platform.
While securely supporting the Bracket, loosen the Bracket Clamp and
adjust the height until the Durometer Indenter is close to the Test Sample
without touching. Tighten the Bracket Clamp to secure at the proper height.
Slowly lower the handle.
The Indenter should contact the Test Sample slowly, at a rate of less than
3.2 mm/s for accurate measurement.
With the handle down, wait the time period specified in the Test Procedure
and then read the Gauge.
When Handle is fully depressed, do not apply additional force as this may
cause damage to the instrument.
Gently raise the handle.
Repeat for additional measurement points as specified by the Durometer
Test Procedure.
Please refer to Durometer Instruction Manual regarding Test Samples and Test Procedures.
Adjustment
Screws
Adjustment Screws
Handle
Stop Ring
DMS-D only
NOTICE Test Platform can be easily damaged - please make
sure the Platform is protected during assembly.
Niigata seiki Co., Ltd.
5-3-14, Tsukanome, Sanjo, Niigata, Japan, 955-0055
Tel. : +81-256-33-5522 Fax. : +81-256-33-5518
URL http://www.niigataseiki.co.jp
URL http://www.niigataseiki.co.jp
/