Dell PowerEdge 2650 クイックスタートガイド

www.dell.com | support.dell.com

Dell™ Systems

Rack Installation Guide

Guide d'installation du rack

Rack-Installationsanleitung

ラック取り付けガイド

Guía de instalación del estante

www.dell.com | support.dell.com

Dell™ Systems

Rack Installation Guide

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, RapidRails, and VersaRails are trademarks of Dell Computer

Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and

names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names

other than its own.

October 2002 P/N 7W226 Rev. A00

Contents 3

Contents

CAUTION: Safety Instructions . . . . . . . . . . . . . . . . . . 1-1

Rack Mounting of Systems. . . . . . . . . . . . . . . . . . . 1-1

Installation Instructions . . . . . . . . . . . . . . . . . . . . . 1-2

Four-Post Rack Installation . . . . . . . . . . . . . . . . . . . . 1-3

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . 1-3

Recommended Tools and Supplies . . . . . . . . . . . . . . . 1-4

RapidRails Rack Kit Contents . . . . . . . . . . . . . . . . . 1-4

VersaRails Rack Kit Contents . . . . . . . . . . . . . . . . . 1-5

Installation Tasks . . . . . . . . . . . . . . . . . . . . . . . 1-5

Removing the Rack Doors . . . . . . . . . . . . . . . . . . . 1-6

Marking the Rack . . . . . . . . . . . . . . . . . . . . . . . 1-6

Installing the RapidRails Slide Assemblies . . . . . . . . . . . 1-8

Installing the VersaRails Slide Assemblies . . . . . . . . . . 1-10

Installing the System in the Rack . . . . . . . . . . . . . . 1-11

Installing the Cable-Management Arm. . . . . . . . . . . . 1-13

Routing Cables . . . . . . . . . . . . . . . . . . . . . . . 1-16

Replacing the Rack Doors . . . . . . . . . . . . . . . . . . 1-17

Two-Post Rack Installation . . . . . . . . . . . . . . . . . . . 1-18

Two-Post Rack Installation Tasks . . . . . . . . . . . . . . 1-18

Recommended Tools and Supplies . . . . . . . . . . . . . . 1-19

Rack Kit Contents . . . . . . . . . . . . . . . . . . . . . . 1-19

Marking the Rack . . . . . . . . . . . . . . . . . . . . . . 1-20

Installing the Slide Assemblies in the Rack. . . . . . . . . . 1-22

Installing the System in the Rack . . . . . . . . . . . . . . 1-27

Installing the Cable-Management Arm. . . . . . . . . . . . 1-27

Routing Cables . . . . . . . . . . . . . . . . . . . . . . . 1-27

4 Contents

Figures

Figure 1-1. RapidRails Rack Kit Contents . . . . . . . . . 1-4

Figure 1-2. VersaRails Rack Kit Contents

. . . . . . . . . 1-5

Figure 1-3. One Rack Unit

. . . . . . . . . . . . . . . . . 1-7

Figure 1-4. Marking the Vertical Rails

. . . . . . . . . . 1-8

Figure 1-5. Installing the RapidRails Slide Assemblies

. . . 1-9

Figure 1-6. Installing the VersaRails Slide Assemblies

. . 1-11

Figure 1-7. Installing the System in the Rack

(RapidRails or VersaRails)

. . . . . . . . . 1-12

Figure 1-8. Installing the Cable-Management Arm

. . . 1-14

Figure 1-9. Installing the Cable-Management Arm

. . . 1-15

Figure 1-10. Routing the Power Cords

. . . . . . . . . . 1-16

Figure 1-11. Routing Cables

. . . . . . . . . . . . . . . 1-17

Figure 1-12. Two-Post Rack Kit Components

. . . . . . . 1-19

Figure 1-13. Two-Post, Open-Frame Relay Rack

Universal-Hole Spacing

. . . . . . . . . . . 1-20

Figure 1-14. Two-Post, Open-Frame Relay Rack

Wide-Hole Spacing

. . . . . . . . . . . . . 1-21

Figure 1-15. Installing the Slide Assemblies for

Center-Mount Configuration

. . . . . . . . 1-23

Figure 1-16. Rotating the Front Mounting Bracket for

Flush-Mount Installation

. . . . . . . . . . 1-25

Figure 1-17. Installing the Slide Assemblies for

Flush-Mount Configuration

. . . . . . . . . 1-26

Rack Installation Guide 1-1

CAUTION: Safety Instructions

Use the following safety guidelines to help ensure your own personal safety and to help

protect your system and working environment f

rom potential damage. For complete safety

information, see the System Information Guide.

Rack Mounting of Systems

Observe the following precautions for rack stability and safety.

Systems are considered to be components in a rack. Thus, "component" refers to any

system as well as to various peripherals or supporting hardware.

CAUTION: Installing systems in a rack without the front and side stabilizers

installed could cause the rack to tip over, potentially resulting in bodily injury

under certain circumstances. Therefore, always install the stabilizers before

installing components in the rack.

After installing system/components in a rack, never pull more than one

component out of the rack on its slide assemblies at one time. The weight of

more than one extended component could cause the rack to tip over and may

result in serious injury.

NOTE: Your system is safety-certified as a free-standing unit and as a component for

use in a Dell™ rack cabinet using the customer rack kit. The installation of your

system and rack kit in any other rack cabinet has not been approved by any safety

agencies. It is your responsibility to ensure that the final combination of system and

rack complies with all applicable safety standards and local electric code

requirements. Dell disclaims all liability and warranties in connection with such

combinations.

• System rack kits are intended to be installed in a rack by trained service technicians. If

you install the kit in any other rack, be sure that the rack meets the specifications of a

Dell rack.

CAUTION: Do not move racks by yourself. Due to the height and weight of the

rack, a minimum of two people should accomplish this task.

• Before working on the rack, make sure that the stabilizers are secured to the rack,

extended to the floor, and that the full weight of the rack rests on the floor. Install

front and side stabilizers on a single rack or front stabilizers for joined multiple racks

before working on the rack.

• Always load the rack from the bottom up, and load the heaviest item in the rack first.

• Make sure that the rack is level and stable before extending a component from the

rack.

1-2 Rack Installation Guide

www.dell.com | support.dell.com

Installation Instructions

This installation guide provides instructions for trained service technicians installing one or

more systems in an open-frame relay rack or in a rack cabinet. The RapidRails™ rack kit can

be installed in all the manufacturer’s rack cabinets without tools, and the VersaRails™ rack

kit can be installed in many industry-standard rack cabinets. The procedures for installing

both RapidRails and VersaRails rack kits are similar. One rack kit is required for each system

to be installed in the rack cabinet.

This guide includes procedures for the following rack kits:

• RapidRails kit in a four-post rack cabinet

• VersaRails kit in a four-post rack cabinet

• Two-post kit (installed in either center-mount or flush-mount configuration, for 3- or

6-inch-wide racks)

For ease in troubleshooting and the identification of system health, these rack kits include a

status-indicator cable that extends the information on the two-color status indicators on

the front and back panels to the back of the cable-management arm. For more information

on these indicators, see your system User’s Guide.

Before attempting this installation, you should read through this entire document carefully.

CAUTION: Do not install rack kit components designed for another system. Use

only the rack kit for your system. Using the rack kit for another system may

result in damage to the system and personal injury to yourself and to others.

• Use caution when pressing the component rail release latches and sliding a

component into or out of a rack; the slide rails can pinch your fingers.

• After a component is inserted into the rack, carefully extend the rail into a locking

position, and then slide the component into the rack.

• Do not overload the AC supply branch circuit that provides power to the rack. The

total rack load should not exceed 80 percent of the branch circuit rating.

• Ensure that proper airflow is provided to components in the rack.

• Do not step on or stand on any component when servicing other components in a

rack.

CAUTION: Safety Instructions (continued)

Rack Installation Guide 1-3

Rack Requirements for VersaRails

NOTICE: The VersaRails rack kit is intended to be installed by trained service

technicians in a rack that meets the specifications of American National

Standards Institute (ANSI)/Electronic Industries Association (EIA) standard

ANSI/EIA-310-D-92, International Electrotechnical Commission (IEC) 297, and

Deutsche Industrie Norm (DIN) 41494. One rack kit is required for each system that

is installed in a rack.

Four-Post Rack Installation

Before attempting this installation, you should read through this entire procedure carefully.

Before You Begin

Before you begin installing your system in the rack, carefully read "CAUTION: Safety

Instructions," found earlier in this guide, as well as the safety instructions found in your

system’s System Information document for additional information.

CAUTION: When installing multiple systems in a rack, complete all of the

procedures for the current system before attempting to install the next system.

CAUTION: Rack cabinets can be extremely heavy and move easily on the casters.

The cabinet has no brakes. Use extreme caution while moving the rack cabinet.

Retract the leveling feet when relocating the rack cabinet. Avoid long or steep

inclines or ramps where loss of cabinet control may occur. Extend the leveling

feet for support and to prevent the cabinet from rolling.

Important Safety Information

Observe the safety precautions in the following subsections when installing your system in

the rack.

CAUTION: You must strictly follow the procedures in this document to protect

yourself as well as others who may be involved. Your system may be very large

and heavy, and proper preparation and planning are important to prevent injury

to yourself and to others. This becomes increasingly important when systems are

installed high up in the rack.

Rack Stabilizer Feet

CAUTION: Installing systems in a rack without the front and side stabilizer feet

installed could cause the rack to tip over, potentially resulting in bodily injury

under certain circumstances. Therefore, always install the stabilizer feet before

installing components in the rack.

1-4 Rack Installation Guide

www.dell.com | support.dell.com

CAUTION: After installing systems in a rack, never pull more than one system

out of the rack on its slide assemblies at one time. The weight of more than one

extended system could cause the rack to tip over and cause injury.

The stabilizer feet help prevent the rack from tipping over when a system or other

component is pulled out of the rack with the slide assemblies fully extended. Refer to the

documentation provided with the rack cabinet for instructions on installing and anchoring

the stabilizer feet.

Recommended Tools and Supplies

You may need the following tools and supplies to install the system in a four-post rack:

• A #2 Phillips screwdriver (for installing VersaRails slide assemblies)

• Masking tape or a felt-tip pen, for use in marking the mounting holes to be used

RapidRails Rack Kit Contents

The RapidRails rack kit includes the following items (see Figure 1-1):

• One pair of RapidRails slide assemblies

• One cable-management arm

• One status indicator cable

• Tie-wraps (not shown in Figure 1-1)

Figure 1-1. RapidRails Rack Kit Contents

slide assemblies (2)

cable-management arm

status indicator cable

Rack Installation Guide 1-5

VersaRails Rack Kit Contents

The VersaRails rack kit includes the following items (see Figure 1-2):

• One pair of VersaRails slide assemblies

• One cable-management arm

• One status indicator cable

• Eight 10-32 x 0.5-inch flange-head Phillips screws

• Tie-wraps (not shown in Figure 1-2)

NOTE: The nonmetric screws described in illustrations and in procedural steps are

identified by size and number of threads per inch. For example, a #10 Phillips-head

screw with 32 threads per inch is identified as a 10-32 screw.

Figure 1-2. VersaRails Rack Kit Contents

Installation Tasks

Installing a rack kit involves performing the following tasks in their numbered order:

1 Removing the rack doors

2 Marking the rack

3 Installing the slide assemblies in the rack:

• RapidRails installation

• VersaRails installation

slide assemblies (2)

10-32 x 0.5-inch

flange-head

Phillips screw (8)

cable-management arm

status indicator cable

1-6 Rack Installation Guide

www.dell.com | support.dell.com

4 Installing the system in the rack

5 Installing the cable-management arm

6 Routing cables

7 Replacing the rack doors

Removing the Rack Doors

See the procedures for removing doors in the documentation provided with your rack

cabinet.

CAUTION: Because of the size and weight of the rack cabinet doors, never

attempt to remove or install them by yourself.

CAUTION: Store the two doors where they will not injure someone if the doors

accidently fall over.

Marking the Rack

You must allow 2 U (88 mm, or 3.5 inches) of vertical space for each system you install in

the rack. Rack cabinets that meet EIA-310 standards have an alternating pattern of three

holes per rack unit with center-to-center hole spacing (beginning at the top hole of a 1-U

space) of 15.9 mm, 15.9 mm, and 12.7 mm (0.625 inch, 0.625 inch, and 0.5 inch) for the

front and back vertical rails (see Figure 1-3). Rack cabinets may have round or square holes.

NOTE: The vertical rails may be marked by horizontal lines and numbers in 1-U

increments. If you wish, you can make a note of the number marking on the rack’s

vertical rail. It is not necessary to mark or place tape on the rack. If you choose this

method, skip ahead to the procedure "Installing the RapidRails Slide Assemblies."

Rack Installation Guide 1-7

Figure 1-3. One Rack Unit

CAUTION: If you are installing more than one system, install the slide assemblies

so that the first system is installed in the lowest available position in the rack.

To mark the rack, perform the following steps:

1 Place a mark on the rack’s front vertical rails where you want to locate the bottom of

the system you are installing in the rack cabinet.

The bottom of each 1-U space is at the middle of the narrowest metal area between

holes (marked with a horizontal line on some rack cabinets—see Figure 1-4).

2 Place a mark 88 mm (3.5 inches) above the original mark you made (or count up six

holes in a rack that meets EIA-310 standards) and mark the rack’s front vertical rails

with a felt-tipped pen or masking tape (if you counted holes, place a mark just above

the top hole). This mark or piece of tape indicates where the system’s upper edge will

be located on the vertical rails (see Figure 1-4).

1 U (44 mm or 1.75 inches)

12.7 mm (0.5 inch)

15.9 mm (0.625 inch)

12.7 mm (0.5 inch)

1-8 Rack Installation Guide

www.dell.com | support.dell.com

Figure 1-4. Marking the Vertical Rails

Installing the RapidRails Slide Assemblies

1 At the front of the rack cabinet, position one of the RapidRails slide assemblies so that

its mounting-bracket flange fits between the marks or tape you placed on the rack (see

Figure 1-5).

The top mounting hook on the slide assembly’s front mounting bracket flange should

enter the top hole between the marks you made on the vertical rails.

2 Push the slide assembly forward until the top mounting hook enters the top square

hole that you placed a mark just above on the vertical rail, and then push down on the

mounting-bracket flange until the mounting hooks seat in the square holes and the

push button pops out and clicks (see Figure 1-5).

tape on

vertical rail

Rack Installation Guide 1-9

Figure 1-5. Installing the RapidRails Slide Assemblies

3

At the back of the cabinet, pull back on the mounting-bracket flange until the top

mounting hook is in the top square hole, and then push down on the flange until the

mounting hooks seat in the square holes and the push button pops out and clicks.

4 Repeat steps 1 through 3 for the slide assembly on the other side of the rack.

5 Ensure that the rails are mounted at the same vertical position on both sides of the

rack.

front of rack

slide assembly (2)

mounting hooks (2)

push button

mounting-

bracket flange

1-10 Rack Installation Guide

www.dell.com | support.dell.com

Installing the VersaRails Slide Assemblies

1 At the front of the rack cabinet, position one of the VersaRails slide assemblies so that

its mounting-bracket flange fits between the marks or tape (or numbered location) on

the rack (see Figure 1-6).

The four holes on the front of the mounting bracket should align with four of the

holes between the marks you made on the front vertical rail.

2 Install two 10-32 x 0.5-inch flange-head Phillips screws in the mounting flange’s top

hole and the third-from-top hole to secure the slide assembly to the front vertical rail

(see Figure 1-6).

3 At the back of the cabinet, pull back on the mounting-bracket flange until the

mounting holes align with their respective holes on the back vertical rail.

4 Install two 10-32 x 0.5-inch flange-head Phillips screws in the back mounting flange’s

top and third-from-top holes to secure the slide assembly to the back vertical rail.

5 Repeat steps 1 through 4 for the slide assembly on the other side of the rack.

6 Ensure that the slide assemblies are mounted at the same position on the vertical rails

on each side of the rack.

Rack Installation Guide 1-11

Figure 1-6. Installing the VersaRails Slide Assemblies

Installing the System in the Rack

CAUTION: If you are installing more than one system, install the first system in

the lowest available position in the rack.

CAUTION: Never pull more than one component out of the rack at a time.

1

Pull the two slide assemblies out of the rack until they lock in the fully extended

position.

CAUTION: Because of the size and weight of the system, never attempt to install

the system in the slide assemblies by yourself.

2

Lift the system into position in front of the extended slides (see Figure 1-7).

front of rack

slide assembly (2)

10-32 x 0.5-inch

flange-head Phillips

screw (4 per slide

assembly)

mounting-bracket

flange

1-12 Rack Installation Guide

www.dell.com | support.dell.com

3 Place one hand on the front-bottom of the system and the other hand on the back-

bottom of the system.

4 Tilt the back of the system down while aligning the back shoulder screws on the sides

of the system with the back slots on the slide assemblies.

5 Engage the back shoulder screws into their slots.

Figure 1-7. Installing the System in the Rack (RapidRails or

VersaRails)

shoulder screw on

system

system release

latch (yellow)

slide release

latch (green)

Rack Installation Guide 1-13

6 Lower the front of the system and engage the front and middle shoulder screws in

their slots (the middle slot is just behind the yellow system release latch) (see

Figure 1-7).

When all shoulder screws are properly seated, the yellow latch on each slide assembly

clicks and locks the system into the slide assembly.

7 Press up on the green slide release latch at the side of each slide to slide the system

completely into the rack (see Figure 1-7).

8 Push in and turn the captive thumbscrews on each side of the front chassis panel to

secure the system to the rack.

NOTE: Use the yellow system release latch whenever you wish to remove the system

from the slide assemblies.

Installing the Cable-Management Arm

NOTICE: The cable-management arm can only be installed on the right side of the

rack cabinet (as viewed from the back).

To install the cable-management arm on the system, perform the following steps:

1 Facing the back of the rack cabinet, locate the latch on the end of the slide assembly.

2 Push the tab on the back end of the cable-management arm into the latch on the end

of the slide assembly (see Figure 1-8).

The latch clicks when locked.

3 Push the tab on the front end of the cable-management arm into a mating latch on

the inner segment of the slide assembly (see Figure 1-8).

The latch clicks when locked.

1-14 Rack Installation Guide

www.dell.com | support.dell.com

Figure 1-8. Installing the Cable-Management Arm

4

Install the system status indicator cable plug into its connector (see Figure 1-9).

5 Open the wire covers on the cable-management arm by lifting the center of the wire

over the top of the embossed round button on the front of the forward part of the arm

and lifting the wire over the top of a similar round button on the back part of the arm.

The wire cover swings open to enable cables to be routed within the arm.

6 Route the system status indicator end of the cable through the cable-management

arm, and install the indicator in its slot at the back end of the cable-management arm

(see Figure 1-9).

latch on inner segment

of slide assembly

cable-management arm

latch on end of

slide assembly

tab on front end

tab on back end

ページを読み込んでいます...

Dell PowerEdge 2650 クイックスタートガイド

関連論文