Cautions
•This unit is designed for negative earth 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all earth wires to a common earth
point.
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
The numbers in the list are keyed to those in the
instructions.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
Connection example (2)
Notes (2-A)
• Be sure to connect the earth cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Tip (2-B-
)
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
Connection diagram (3)
1 To a metal surface of the car
First connect the black earth lead, then connect
the yellow and red power input leads.
2 To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there is
no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/MW/SW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the interface cable of a car telephone
5 To the +12 V power terminal which is energised
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black earth lead to it first.
• When your car has a built-in FM/MW/SW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
6 To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth lead to it first.
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/MW/SW aerial in the
rear/side glass, connect the power aerial control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing aerial booster.
For details, consult your dealer.
• A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and
with adequate power handling capacities to avoid
its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker cords to each
other.
3-237-883-31 (1)
Installation/Connections
FM/MW/SW
Cassette
Car stereo
Sony Corporation © 2002 Printed in Thailand
XR-CA640X
1
12
× 4
3
4675
× 2
Equipment used in illustrations (not supplied)
Power amplifier
CD/MD changer
Front speaker
Rear speaker
2
B
BUS AUDIO IN
BUS CONTROL IN
BUS CONTROL IN
BUS AUDIO IN
A
Rotary commander RM-X4S
RM-X4S
AUDIO OUT RAER
Source selector
*
*not supplied
AUDIO OUT FRONT
3
•
•
•
•
•
•
•
•
1
1
2
2
•
•
2
3
1
2
•
•
3
4
5
•
•
6
•
•
•
•
•
•
•
•
•
•
•
L
R
AUDIO OUT
FRONT
AUDIO OUT
REAR
BUS
AUDIO
BUS AUDIO IN
Source selector
(not supplied)
XA-C30
2
5
6
4
AMP REM
ATT
7
Max. supply current 0.1 A
Red
Yellow
Black
Blue
BUS
CONTROL IN
AUDIO OUT
FRONT
REMOTE
IN
AUDIO OUT
REAR
3
1
Light blue
ANT REM
Supplied with the CD/MD changer
Supplied with XA-C30
XA-C30
from car aerial
RCA pin cord (not supplied)
RCA
Fuse (10 A)
Insert with the cord upwards.
Left
Right
Left
Right
Max. supply current 0.3 A
Blue/white striped
White
Green
Purple
White/black striped
Grey/black striped
Green/black striped
Purple/black striped
Grey
•
•
: ,
•
,
•
•
•
•
,
•
,
(1)
1
(2)
(A-
2
)
•
•
,
( -B-
2
)
åÍœ wÝò
CD
åÍœ Â≈òØ
MD
,
XA-C30
(3)
1
2
•
,
•
FM/MW/SW
,
3
AMP REMOTE IN
4
5
+
•
,
+
•
FM/MW/SW
,
6
+
•
+
•
FM/MW/SW
,
,
•
,
•
,
•
•
,
•
(–)
•
•
•
,
(–)
•
182 mm
53 mm
4 A
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
•There must be a distance of at least 15 cm between
the cassette slot of the unit and shift lever in order
to insert a cassette easily. Choose the installation
location carefully so the unit does not interfere
with gear shifting and other driving operations.
15 cm
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
How to detach and attach the
front panel (4)
Before installing the unit, detach the front
panel.
4-A To detach
Before detaching the front panel, be sure to
press (OFF). Press (OPEN), then slide the front
panel to the right side, and pull out the left side.
4-B To attach
Place the hole
in the front panel onto the
spindle
on the unit as illustrated, then push
the left side in.
B
Mounting example (5)
Installation in the dashboard
Mounting the unit in a Japanese
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 4.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc.
1 2 3
Bend these claws outward
for a tight fit, if necessary.
2
6
4
4
5
5
4
4
1
1
Fire wall
Dashboard
5
5
c
3
•
•
•
•
15 cm
4
4
(OFF) (OPEN)
4
5
6
4
(OFF)
(OFF)
6 A
to dashboard/center console
Bracket
Bracket
max. size
5 × 8 mm
×
B
4
max. size
5 × 8 mm
×
TOYOTA NISSAN
4
to dashboard/center console
Bracket
Bracket
4
Existing parts supplied with your car
Existing parts supplied with your car
max. size
5 × 8 mm
×
max. size
5 × 8 mm
×
4
•
•, ,
, ,
•
•
15
cm
°
(4)
,
A-
4
,
(OFF)
(OPEN)
,
B-
4
,
(5)
(6)
,
,
4
ACC
(OFF)
(OFF)
,
RESET
,
RESET
-
1
-
2
-
3
-
4
