© 2003 Sony Corporation Printed in Korea
CDX-MP80
Cautions
•This unit is designed for negative earth 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all earth wires to a common earth
point.
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Before installation (1)
•Do not install the unit where its operation
interferes with driving. (1)
Example:
— Opening and closing of the front panel or
disc tray interfere with operation of the
gear shift.
— With the front panel open, operation of
hazard lamps, switches etc., is impaired.
Parts Iist (2)
The numbers in the list are keyed to those in the
instructions.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
TOP
Installation/Connections
FM/MW/LW
Compact Disc
Player
Connection example (3)
Notes (3-A)
• Be sure to connect the earth cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Tip (3-B-
)
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
Connection diagram (4)
1 To a metal surface of the car
First connect the black earth lead, then connect
the orange/white striped, yellow, and red power
input leads.
2 To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
•It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the interface cable of a car telephone
5 To a car’s illumination signal
Be sure to connect the black earth lead to a
metal surface of the car first.
6 To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black earth lead to a
metal surface of the car first.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
7 To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth lead to a
metal surface of the car first.
1
TOP
6 7
Equipment used in illustrations (not supplied)
Rear speaker
Front speaker
2
Power amplifier
CD/MD changer
× 4
4
× 2
5
3-251-178-31 (1)
2 3
3 A
B
SUB OUT (MONO)
AUDIO OUT
REAR
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
BUS CONTROL IN
Source selector*
*
XA-C30
* not supplied
AUDIO OUT
FRONT
Active subwoofer
1
124
19
60
18.5
142.5
170
Unit: mm
Dimensions include unit size, front panel and disc tray open, etc.
Rotary commander RM-X4S
FRONT
AUDIO OUT
REARBUS
AUDIO IN
•
•
•
•
•
•
•
•
1
• 1
2
1
TOP
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner or when you
activate the AF (Alternative Frequency), TA (Traffic
Announcement) function.
• When your car has built-in FM/MW/LW aerial in
the rear/side glass, connect the power aerial
control lead (blue) or the accessory power input
lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
•A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker cords to each
other.
3
3
•
•
3
4
1
2
•
•
3
4
5
6
•
•
7
•
•
•
•
•
•
•
•
•
•
•
3
from car aerial
2
5
4
AMP REM
7
Max. supply current 0.3 A
Fuse (10 A)
Red
Yellow
Black
Blue/white striped
White
Green
Purple
White/black striped
Grey/black striped
Green/black striped
Purple/black striped
Grey
Supplied with XA-C30
4
Left
Right
Left
Right
3
ANT REM
1
Blue
Max. supply current 0.1 A
Light blue
6
ATT
Source selector
(not supplied)
XA-C30
Supplied with the CD/MD changer
*
1
*
1
*
1
7
ILLUMINATION
Orange/white striped
*
3
*
2
BUS AUDIO IN
BUS
CONTROL IN
AUDIO OUT REAR
AUDIO OUT
FRONT
*
1
RCA pin cord (not
supplied)
*
2
Auxiliary optional
equipment such as
portable DVD player DVP-
FX1 (not supplied)
*
3
supplied with the auxialiry
equipment
*
4
Be sure to match the color-
coded code for audio to
the appropriate jacks from
the unit.
*
5
Insert with the cord
upwards
AUX IN
(AUDIO)
*
4
SUB OUT (MONO)
REMOTE IN
*
5
5 AB
(OFF)
TOP
1
2
3
Bend these claws outward
for a tight fit, if necessary.
6
4
4
5
5
4
4
182 mm
53 mm
TO
P
1
1
Dashboard
5
6
7 A TOYOTA
to dashboard/centre console
Bracket
Bracket
max. size
5 × 8 mm
B NISSAN
4
max. size
5 × 8 mm
4
to dashboard/centre console
Bracket
Bracket
4
max. size
5 × 8 mm
max. size
5 × 8 mm
4
Existing parts supplied with your car
Existing parts supplied with your car
(RELEASE)
A
B
2
3
Fire wall
with the TOP marking up
*
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 30°.
How to detach and attach the
front panel (5)
Before installing the unit, detach the front
panel.
5-A To detach
Before detaching the front panel, be sure to
press (OFF). Press (RELEASE) to open up the
front panel and pull it off towards you.
5-B To attach
Attach part A of the front panel to part B of the
unit as illustrated and push the left side into
position until it clicks.
Mounting example (6)
Installation in the dashboard
When installing this unit, be sure to close the
front panel of the unit. (6-
*
)
Do not hold the unit by its front panel or disc
tray when installing as this can damage the unit,
or cause malfunction.
Mounting the unit in a Japanese
car (7)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 4.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
After tuning off the ignition, be sure to
press and hold (OFF) on the unit until the
clock display disppears.
Otherwise, the display does not turn off and this
causes battery drain.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc., after removing the
front panel.
•
•
•
5
5
(OFF)
(RELEASE)
5
A B
6
6
*
7
4
(OFF)
-
1
-
2
-
3
-
4
