Sony CDX-M1000TFは、車載用CDプレイヤーです。フロントパネルにCDスロットがあり、CDを挿入して音楽を再生できます。また、フロントパネルには、電源ボタン、ボリュームコントロール、トラック送り/戻しボタン、ソースセレクターボタン、ディスプレイ、イコライザーボタンがあります。ディスプレイには、再生中の曲の情報や、ラジオの周波数などが表示されます。イコライザーボタンを押すと、音質を調整するためのメニューが表示されます。ソースセレクターボタンを押すと、CD、ラジオ、AUXなどのソースを選択できます。AUX端子は、外部オーディオ機器を接続するための端子です。
Sony CDX-M1000TFは、車載用CDプレイヤーです。フロントパネルにCDスロットがあり、CDを挿入して音楽を再生できます。また、フロントパネルには、電源ボタン、ボリュームコントロール、トラック送り/戻しボタン、ソースセレクターボタン、ディスプレイ、イコライザーボタンがあります。ディスプレイには、再生中の曲の情報や、ラジオの周波数などが表示されます。イコライザーボタンを押すと、音質を調整するためのメニューが表示されます。ソースセレクターボタンを押すと、CD、ラジオ、AUXなどのソースを選択できます。AUX端子は、外部オーディオ機器を接続するための端子です。
© 2003 Sony Corporation Printed in Korea
CDX-M1000TF
3-251-038-31 (1)
Cautions
•This unit is designed for negative earth 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all earth wires to a common earth
point.
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
•The numbers in the list are keyed to those in
the instructions.
•The bracket 1 is attached to the unit before
shipping. Before mounting the unit, use the
release keys 6 to remove the bracket 1 from
the unit. For details, see “Removing the
bracket (4)” on the reverse side of the sheet.
•Keep the release keys 6 for future use as
they are also necessary if you remove the
unit from your car.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
Note
Before installing, make sure that the catches on
both sides of the bracket 1 are bent inwards 2 mm.
If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
Installation/Connections
FM/MW/LW
Compact Disc
Player
Connection example (2)
Note (2-A)
Be sure to connect the earth cord before connecting
the amplifier.
Tip (2-B-
)
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
Connection diagram (3)
1 To a metal surface of the car
First connect the black earth lead, then connect
the orange/white striped, yellow, and red power
input leads.
2 To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the interface cable of a car telephone
5 To a car’s illumination signal
Be sure to connect the black earth lead to a
metal surface of the car first.
6 To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black earth lead to a
metal surface of the car first.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
7 To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth lead to a
metal surface of the car first.
Equipment used in illustrations (not supplied)
2
B
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
BUS CONTROL IN
Source selector*
*
XA-C30
* not supplied
SUB OUT (MONO)
A
AUDIO OUT
FRONT
AUDIO OUT
REAR
1
3
4
7
× 4
56
12
× 2
8
Active subwoofer
Rear speaker CD/MD changer
Front speaker Power amplifier
Rotary commander RM-X4S
1
Catch
L
R
BUS AUDIO IN
SUB OUT
/AUX IIN
3
Supplied with XA-C30
Source selector
XA-C30
2
6
7
4
ANT REM
7
Red
Yellow
Black
Blue
BUS
CONTROL IN
Supplied with the CD/MD changer
Light blue
Max. supply current 0.1 A
ATT
1
SUB OUT (MONO)
Orange/white striped
5
ILLUMINATION
*
2
•
•
•
•
•
•
•
•
1
•
• 1
6
1
4
•
6
1
1
2
2
2
3
1
2
•
•
3
4
5
6
•
•
7
•
•
•
*
5
1
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner or when you
activate the AF (Alternative Frequency), TA (Traffic
Announcement) function.
• When your car has built-in FM/MW/LW aerial in
the rear/side glass, connect the power aerial
control lead (blue) or the accessory power input
lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
• A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker cords to each
other.
*
1
RCA pin cord (not supplied)
*
2
Auxiliary optional equipment such as portable DVD player
(not supplied)
*
3
supplied with the auxialiry equipment
*
4
Be sure to match the color-coded code for audio to the
appropriate jacks from the unit.
If you connect an optional CD/MD unit, you cannot use
AUX IN terminal.
*
5
Insert with the cord upwards.
3
Fuse (10 A)
Blue/white striped
AMP REM
Max. supply current 0.3 A
*
3
*
1
from car aerial
*
1
BUS AUDIO IN/
AUX IN
*
4
AUDIO OUT
REAR
AUDIO OUT
FRONT
•
•
•
•
•
•
•
•
REMOTE IN
White
Green
Purple
White/black striped
Grey/black striped
Green/black striped
Purple/black striped
Grey
Left
Right
Left
Right
182 mm
53 mm
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 60°.
Removing the bracket (4)
Before installing the unit, remove the bracket
1 from the unit.
1 Insert both release keys 6 together
between the unit and the bracket 1 until
they click.
2 Pull down the bracket 1, then pull up the
unit to separate.
Before installation (5)
Do not install the unit where its operation
interferes with driving.
Example:
— Opening and closing of the front panel
interfere with operation of the gear shift.
— With the front panel open, operation of
hazard lamps, switches etc., is impaired.
Mounting example (6)
Installation in the dashboard
When installing this unit, be sure to close the
front panel of the unit and attach the front
panel cover 8. (6-
*
)
•Do not push the LCD display directly. The
display may break and cause injury to your
fingers. When installing the unit, be sure to
attach the supplied front panel cover 8.
•Do not hold the unit by its front panel when
installing as this can damage the unit, or cause
malfunction.
Notes
• Bend these claws outwards for a tight fit, if
necessary.
(6-2)
• Make sure that the 4 catches on the protection
collar 4 are properly engaged in the slots of the
unit.
(6-3)
Mounting the unit in a Japanese
car (7)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 5.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
After turning off the ignition, be sure to
press and hold (OFF) on the unit until the
display disappears.
Otherwise, the display does not turn off and this
causes battery drain.
*
6
1
3
2
8
Dashboard
Fire wall
4
2
3
1
1
•
•
•
4
1
6 1
1
5
6
8 6
*
•
8
•
• 6
•
4
6
4 5
6
1
Dimensions include unit size, front panel and disc tray open, etc.
170 mm59 mm
19 mm
9.5 mm
Reset button
When the installation and connections are
completed, be sure to press the reset button with
a ballpoint pen, etc.
cc
Face the hook inwards.
Claws
7 A TOYOTA
to dashboard/centre console
Bracket
Bracket
max. size
5 × 8 mm
B NISSAN
5
max. size
5 × 8 mm
5
to dashboard/centre console
Bracket
Bracket
5
max. size
5 × 8 mm
max. size
5 × 8 mm
5
Existing parts supplied with your car
Existing parts supplied with your car
7
5
(OFF)
-
1
-
2
-
3
-
4
Sony CDX-M1000TFは、車載用CDプレイヤーです。フロントパネルにCDスロットがあり、CDを挿入して音楽を再生できます。また、フロントパネルには、電源ボタン、ボリュームコントロール、トラック送り/戻しボタン、ソースセレクターボタン、ディスプレイ、イコライザーボタンがあります。ディスプレイには、再生中の曲の情報や、ラジオの周波数などが表示されます。イコライザーボタンを押すと、音質を調整するためのメニューが表示されます。ソースセレクターボタンを押すと、CD、ラジオ、AUXなどのソースを選択できます。AUX端子は、外部オーディオ機器を接続するための端子です。
他の言語で
- English: Sony CDX-M1000TF Installation guide