1
H3C WX3500H Series Access Controllers Installation Quick Start-6W104
H3C WX3500H系列无线控制器 快速安装指南-6W104
BOM:3104A0FG
Tool list 工具参考
Introduction to installation accessories 安装附件介绍
2
Cage nut
(user-supplied)
浮动螺母（用户自备）
Grounding cable
(provided)
地线（标配）
Removable cable tie
(user-supplied)
可拆卸式扎带（用户自备）
M6 screw
(user-supplied)
M6 螺钉（用户自备）
Mounting bracket
(provided)
挂耳（标配）
Rubber feet
(provided)
脚垫贴（标配）
Console cable
(provided)
配置电缆（标配）
The installation tools are not provided with the access controller. Prepare them yourself.
设备不随机提供安装工具，请用户根据实际安装需求自己准备安装工具。
Needle-nose pliers
尖嘴钳
Wire-stripping pliers
剥线钳
Diagonal pliers
斜口钳
Marker
记号笔
Phillips screwdriver
十字螺丝刀
The WX3500H Series Access Controllers include the WX3510H, WX3520H and WX3540H models.
The installation procedures are the same for the three models. This guide uses the WX3540H
access controller as an example.
WX3500H系列包括WX3510H、WX3520H和WX3540H三款无线控制器，安装方式完全相同，本文
以WX3540H为例介绍设备的安装过程。
Flathead screwdriver
一字螺丝刀
ESD wrist strap
防静电腕带
Heat gun
热风枪
Wear an ESD wrist strap, and make sure the wrist strap makes good skin contact and is reliably
grounded.
操作者需佩戴防静电腕带，确保防静电腕带与皮肤良好接触，并确认防静电腕带已经良好接地。
!
Mounting the access controller on a workbench 安装设备
到工作台
Make sure the air inlet and outlet vents are not blocked and the installation site has a good ventilation system.
请确保设备的进、出风孔不被遮挡，并将设备安装在具有良好通风散热系统的环境中。
Airflow of the access controller 设备的风向设计
Make sure the workbench is stable and reliably grounded.
Do not place heavy objects on the access controller. Attach
the rubber feet to the four round holes in the chassis bottom.
Place the access controller on the workbench.
保证工作台的平稳与良好接地，并且不要在设备上放置重物。
粘贴脚垫贴到设备底部，将带脚垫贴的设备平放到工作台上。
Left-to-right airflow.
设备采用左进右出的风道设计。
4
3
Connecting the grounding cable 连接保护地线
Mount the access controller in the rack.
安装设备到机柜。
Mounting the access controller in a rack 安装设备到机柜
Install cage nuts.
安装浮动螺母。
Attach the mounting brackets to the access controller.
Front, middle, and rear mounting positions are available for
The mounting brackets. Determine the mounting position for
the mounting brackets as required.
安装挂耳到设备。挂耳支持前置、中置和后置的安装方式，请
用户根据机房实际环境选择对应的挂耳安装方式。
Correctly connecting the grounding cable is crucial to lightning protection and EMI protection. To
guarantee the grounding effect, use the grounding cable provided with the access controller.
设备地线的正确连接是设备防雷、防干扰的重要保障，请使用设备随机提供的保护地线正确接地。
To connect the grounding cable when you mount the access controller on a workbench:
1. Connect one end of the grounding cable to the access controller and secure it with the grounding Screw
provided with the access controller.
2. Connect the other end of the grounding cable to the grounding equipment in the building. If The installation
site does not have grounding equipment but earth ground is available, Ground the access controller by
burying a grounding conductor in the earth ground.
设备安装在工作台时，应将接地线一端与设备相连，并使用随机提供的接地螺钉固定，接地线另一端与楼宇
接地装置相连。如果安装环境中不具备专用的接地线连接装置也可以采用埋设接地体的方式将设备妥善接地。
6
5
Installing a power module 安装电源模块
Connecting the AC power cord 连接交流电源线
AC power module
交流电源模块
DC power module
直流电源模块
Do not install AC and DC power modules on the same access controller.
设备不支持交流和直流电源模块混插。
1. Put the two ends of the bail latch through the two loops on the left side of the AC-input
Power receptacle, and pull the bail latch leftwards.
将电源线卡勾安装到电源卡勾座上，并将卡勾朝左扳。
2. Plug one end of the AC power cord into the receptacle of the AC power module.
将设备的交流电源线一端插到电源输入插口上。
3. Pull the bail latch rightwards to secure the plug to the power receptacle.
将电源线卡勾朝右扳，卡住电源线插头。
1. Insert the AC or DC power module in the target power module slot. The following figure uses power module
slot 1 as an example.
在电源槽位1插入AC/DC电源模块。
2. Fasten the screws to secure the power module in place.
旋紧固定螺钉。
Before connecting the power cord, make sure the access controller is reliably grounded.
在连接电源线前，需保证设备已正确接地。
Connect the power cord to the access controller first and then to the power supply system of the
equipment room to avoid bodily injury.
在连接电源线时，请先完成电源线与设备侧的连接，再进行电源线与机房供电系统的连接，以免造成
人身伤害。
To connect the grounding cable when you mount the access controller in a rack:
1. Connect the grounding cable of the building to the grounding strip on the rack. Make sure the rack is
reliably grounded.
2. Use the grounding cable provided with the access controller to connect the access controller to the
grounding strip on the rack.
设备安装在机柜时，要求机柜已经良好接地，首先需将楼宇保护地线与机柜接地排相连，然后使用接地线将
设备与机柜接地排相连。
-
1
-
2
-
3
-
4
他の言語で
- English: H3C WX3500H series
関連論文
-
H3C SR6604-X Installation, Quick Start
-
-
-
-
-
-
-