Samsung SMC-212H/CHN 取扱説明書

COLOR MONITOR

SMC-212H/SMC-142H

User Guide

Mode d’emploi

Bedienungsanleitung

Manuale dell'utente

Guía del usuario

SMC-212H/SMC-142H cover 8/23/02 5:36 PM Page 1

Contents

Graphic Symbol Explanation....................................................iii

IMPORTANT SAFEGUARDS .............................................. iv

FCC & ICES Information ...................................................... vii

General .................................................................................. viii

Specifications ........................................................................ e-2

Front Panel Components and Controls ................................. e-4

Rear Panel Components and Controls ................................ e-12

Connections ........................................................................ e-13

Maintenance ........................................................................ e-14

ii

1_SMC_142_eng 8/23/02 5:19 PM Page ii

Graphic Symbol Explanation

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated ‘dangerous voltage’ within the product’s enclosure

that may be of sufficient magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

Warning - To Prevent Fire or Shock Hazard, Do Not

Expose This Monitor To Rain or Moisture.

iii

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

1_SMC_142_eng 8/23/02 5:19 PM Page iii

IMPORTANT SAFEGUARDS

Caution

Power source is indicated on the rear of the set. It contains high-voltage

parts. If you remove the cover, it may cause fire or electric shock.

Do not remove the cover by yourself. (Control switches are at the front of

the monitor).

1. Read Instructions : All the safety and operating instructions should be

read before the appliance is operated.

2. Retain Instructions : The safety and operating instructions should be

retained for future reference.

3. Heed Warnings : All warnings on the monitor and in the operating

instructions should be adhered to.

4. Follow Instructions : All operating and use instructions should be

followed.

5. Cleaning : Unplug this monitor from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for

cleaning.

Exception. A monitor that is meant for uninterrupted service and that

for some specific reason, such as the possibility of the loss of an

authorization code for a CATV converter, is not intended to be

unplugged by the user for cleaning or any other purpose, may exclude

the reference to unplugging the monitor in the cleaning description

otherwise required in Item 5.

6. Attachments : Do not use attachments not recommended by Samsung

as they may cause hazards.

7. Water and Moisture : Do not use this monitor near water for example,

near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet

basement, or near a swimming pool, and the like.

iv

1_SMC_142_eng 8/23/02 5:19 PM Page iv

8. Accessories : Do not place this monitor on an unstable cart, stand,

tripod, bracket, or table. The monitor may fall, causing serious injury to

a child or adult, and serious damage to the appliance. Use only with a

cart, stand, tripod, bracket, or table recommended by Samsung, or sold

with the monitor. Any mounting of the monitor should follow

Samsung’s instructions, and should use a mounting accessory

recommended by Samsung.

9. Ventilation : Slots and openings in the cabinet are provided for

ventilation and to ensure reliable operation of the monitor and to protect

it from overheating, and these openings should never be blocked by

placing the monitor on a bed, sofa, rug, or other similar surface. This

monitor should never be placed near or over a radiator or heat register.

This monitor should not be placed in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or Samsung’s

instructions have been adhered to.

10. Power Sources : This monitor should be operated only from the type of

power source indicated on the making label. If you are not sure of the

type of power supply to your installation site, consult your Samsung

dealer or local power company.

11. Grounding or Polarization : For monitors equipped with a 3-wire

grounding-type plug having a third(grounding)pin. This plug will only

fit into a grounding type power outlet. This is a safety feature. If you are

unable to insert the plug into the outlet, contact your electrician to

replace your obsolete outlet. Do not defeat the safety purpose of the

grounding-type plug.

12. Power : Cord Protection-Power supply cords should be routed so that

they are not likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the monitor.

v

1_SMC_142_eng 8/23/02 5:19 PM Page v

13. Lightning : For added protection for this monitor during a lightning

storm, or when it is left unattened and unused for long periods of time,

unplug it from the wall outlet and disconnect the cable system. This will

prevent damage to the monitor due to lightning and power-line surges.

14. Overloading : Do not overload wall outlets and extension cords as this

can result in a risk of fire of electric shock.

15. Object and Liquid Entry : Never push objects of any kind into this

monitor through openings as they may touch dangerous voltage points

or short-out parts that could result in a fire or electric shock. Never spill

liquid of any kind on the monitor.

16. Servicing : Do not attempt to service this monitor yourself as opening

or removing covers may expose you to dangerous voltage or other

hazards. Refer all servicing to qualified service personnel.

17. Damage Requiring Service : Unplug this monitor from the wall outlet

and refer servicing to qualified service personnel under the following

conditions.

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the monitor.

c. If the monitor has been exposed to rain or water.

d. If the monitor does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the

operating instructions as an improper adjustment of other controls

may result in damage and will often require extensive work by a

qualified technician to restore the monitor to its normal operation.

e. If the monitor has been dropped or the cabinet has been damaged.

f. When the monitor exhibits a distinct change in performance-this

indicates a need for service.

vi

1_SMC_142_eng 8/23/02 5:19 PM Page vi

18. Replacement Parts : When replacement parts are required, be sure the

service technician has used replacement parts specified by Samsung or

have the same characteristics as the original parts.

Unauthorized substitutions may result in fire, electric shock or other

hazards.

19. Safety Check : Upon completion of any service or repairs to this

monitor, ask the service technician to preform safety checks to

determine that the monitor is in proper operating condition.

FCC & ICES Information

Warning

This equipment has been tested and found to comply the limits for a class A

digital device, pursuant to part 15 of the FCC Rules and ICES-003 of

Industry Canada. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial

environment. This equipment generate, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct

the interference at his own expense.

User-Installer Caution

Your authority to operate this FCC verified equipment could be voided if

you make changes or modifications not expressly approved by the party

responsible for compliance to part 15 of the FCC Rules.

vii

1_SMC_142_eng 8/23/02 5:19 PM Page vii

General

Scope

The information in this instruction manual covers the installation and

operation of the Color Monitors.

These units should be installed using approved materials and wiring

practices in accordance with the National Electrical Code and applicable

local wiring ordinances.

Introduction

The Color Monitors, having a resolution of more than 450 lines at center.

Designed primarily for industrial applications this monitor accepts standard

NTSC/PAL color input signals.

Operating controls (Contrast,Brightness,Color,Tint, Sharpness, Auto time,

Auto skip, Camera OSD, Preset) are located on the Menu.(*Tint : only

NTSC signal)

A regulated power supply maintains excellent performance during

fluctuations in line voltage.

The Color Monitors are housed in a metallic dark-gray color cabinet

viii

1_SMC_142_eng 8/23/02 5:19 PM Page viii

Before operating the unit, please read this manual throughly,

and retain it for future reference.

1_SMC_142_eng 8/23/02 5:19 PM Page e-1

e-2

Specifications

System SMC-142H (NTSC/PAL)

CRT 14” diagonal, 0.66 stripe pitch, 90° deflection

Video In/Out 4 Channel Input/1 Channel Output 1.0Vp-p

BNC jack

Audio In/Out 4 Channel Input/1 Channel output RCA jack

Control Front Menu (Contrast, Brightness, Tint, Color,

Sharpness, Auto time, Auto skip, Preset)

Power Source Control range of main section 90V~260V or

“Indicated on the rear of the MONITOR set”

Power Consumption 68Watts

Dimensions 365mm x 342mm x 391mm (W x H x D),

without packing

Weight 12Kg (with packing)

Resoultion 450 TV lines

Video System Multiple system

(NTSC/PAL)

Horizontal Stabilization Pull in Range ± 500Hz

Holding Range ± 500Hz

Vertical Stabilization Pull in Range ± 4Hz

Holding Range ± 4Hz

Sub Carrier Stabilization Pull in Range ± 400Hz

Holding Range ± 400Hz

Audio 1.5Watts

Convergence Less than 0.4mm Max(Center)

Overscan 10%

Operating Temperature 0°C ~ +40°C

Operating Humidity 10 ~ 90% (Non-condensing)

1_SMC_142_eng 8/23/02 5:19 PM Page e-2

Specifications

System SMC-212H (NTSC/PAL)

CRT 21” diagonal, 0.7 stripe pitch, 90° deflection

Video In/Out 4 Channel Input/1 Channel Output 1.0Vp-p

BNC jack

Audio In/Out 4 Channel Input/1 Channel output RCA jack

Control Front Menu (Contrast, Brightness, Tint, Color,

Sharpness, Auto time, Auto skip, Preset)

Power Source Control range of main section 90V~260V or

“Indicated on the rear of the MONITOR set”

Power Consumption 82Watts

Dimensions 490mm x 444mm x 482mm (W x H x D),

without packing

Weight 25kg (with packing)

Resoultion 450 TV lines

Video System Multiple system

(NTSC/PAL)

Horizontal Stabilization Pull in Range ± 500Hz

Holding Range ± 500Hz

Vertical Stabilization Pull in Range ± 4Hz

Holding Range ± 4Hz

Sub Carrier Stabilization Pull in Range ± 400Hz

Holding Range ± 400Hz

Audio 1.5Watts

Convergence Less than 0.4mm Max(Center)

Overscan 10%

Operating Temperature 0°C ~ +40°C

Operating Humidity 10 ~ 90% (Non-condensing)

e-3

1_SMC_142_eng 8/23/02 5:19 PM Page e-3

Front Panel Components and Controls

POWER Switch

POWER On/Off Switch. If you press this switch, the monitor is turned on

and the LED of selected input signal is lit.

Auto/Manual Mode Selection Button

When pressing this button, LEDs are lit red in Auto mode, and green in

Manual mode.

e-4

POWER

AUTO

R : AUTO

G : MANUAL

SMC-142H

SMC-212H

1_SMC_142_eng 8/23/02 5:19 PM Page e-4

Using Auto Mode

To use AUTO mode, press the AUTO button to light LED red.

In Auto mode, the channel for CAMERA input is automatically converted

as the following OSD, in CA1 ➝ CA2 ➝ CA3 ➝ CA4 order, at an interval

of auto time (2 to 10 seconds, set in MENU mode):

e-5

CA1

CA2

CA3

(After Auto time)

••••

(After Auto time)

1_SMC_142_eng 8/23/02 5:19 PM Page e-5

Using Auto Skip mode

In Auto mode,when no input channel are 2 and 4,and Auto Skip on in

MENU,Monitor is operated as follows.

e-6

(After Auto time)

After 1 second After 1 second After 1 second

(After Auto time) (After Auto time)

CA1 Scanning

CA2 Scanning

No Input

CA3 Scanning

CA4 Scanning

No Input

After (Scanning 4 Channels, Each channel scanning time : 1sec)

CA1

CA3

CA1

CA3

After 1 second After 1 second After 1 second

CA1 Scanning

CA2 Scanning

No Input

CA3 Scanning CA4 Scanning

No Input

After (Scanning 4 Channels, Each channel scanning time : 1sec)

1_SMC_142_eng 8/23/02 5:19 PM Page e-6

Using Manual Mode

To select a channel for CAMERA input manually, press the AUTO button to

to light LED green :

Pressing each of camera switches functions as :

CAMERA 1 Button

Pressing this button enables the conversion to CAMERA1 in MANUAL and

MENU mode.

CAMERA 2 Button

Pressing this button enables the conversion to CAMERA2 in MANUAL and

MENU mode.

CAMERA 3 Button

Pressing this button enables the conversion to CAMERA3 in MANUAL and

MENU mode.

CAMERA 4 Button

Pressing this button enables the conversion to CAMERA4 in MANUAL and

MENU mode.

e-7

1_SMC_142_eng 8/23/02 5:19 PM Page e-7

Menu Mode (Using MENU button)

Pressing MENU button to convert into Menu mode.

MENU Button - VOLUME

Pressing MENU button enables the conversion to each menu.

Then, every user-controllable menu will be displayed, in the following order:

Contrast ➔ Brightness ➔ Sharpness ➔ Color ➔ Tint(only NTSC) ➔

Auto Time ➔ Auto Skip ➔ Camera OSD ➔ Preset ➔ Menu Exit

Setting up the value of each Menu

1. Pressing MENU button to select Menu which you wish to set it’s value.

2. Set value of that menu by using VOLUME button.

3. Return the Main Menu after having performed setting and, then select

otherMenu.

(Press MENU button to return to the Main Menu.)

e-8

1_SMC_142_eng 8/23/02 5:19 PM Page e-8

Settings Range in Each MENU

MENU Settings Range Explanation

Contrast 0~100 To select a specific Contrast within the

setting range.

Brightness 0~100 To select a specific Brightness within

the setting range.

Sharpness 0~100 To select a specific Sharpness within

the setting range.

Color 0~100 To select a specific Color within the

setting range.

Tint G 0~100 To select a specific Tint within the

R 100~0 setting range. (Only NTSC)

Auto time 2~10 sec To select a time interval, when a

channel is converted in Auto mode

within the setting range.

Auto skip On/Off To skip over No Input channels in Auto

mode (On), or to display them instead

of skipping over (Off).

Camera OSD On/Off

It shows characters for Channel (OSD) (On)

It does not chow characters for Channel

(OSD) (Off)

Preset To set values of all menus as default.

Adjusting Settings of Menus : Contrast, Brightness, Sharpness, Color, Tint,

and Auto time, with VOLUME button.

• Select each Menu and then press VOLUME button.

• A bar with which settings of the selected menu can be adjusted will

be displayed.

• Pressing VOLUME button decreases settings of the menu.

• Pressing VOLUME button increases settings of the menu.

e-9

1_SMC_142_eng 8/23/02 5:19 PM Page e-9

Adjusting Settings of Auto Skip Menu with VOLUME button.

• Select the Auto Skip Menu in Menu mode.

• VOLUME button toggles the value of Auto Skip between On

and Off.

Adjusting Settings of Preset Menu with VOLUME button.

• Select the Preset Menu in Menu mode.

• Pressing VOLUME button changes the settings of Preset Menu

to default.

Defaults of Preset Menu are as follows:

Preset Default value

Contrast 60

Brightness 50

Sharpness 50

Color 50

Tint 50

Auto time 2 sec

Auto skip OFF

Camera OSD ON

To return the main menu after having selected and performed each menu,

press the MENU button again.

e-10

1_SMC_142_eng 8/23/02 5:19 PM Page e-10

Exiting from Menu mode

• After 20 seconds have elapsed without pressing any button in Menu

mode, Menu mode is closed.

Adjusting Volume

• The volume-adjustable bar will be displayed. Pressing VOLUME

button turns the volume down, and VOLUME button turns the

volume up.

• When 5 seconds have elapsed without pressing any button with the

volume bar displayed, the volume remains its original state, unchanged.

e-11

1_SMC_142_eng 8/23/02 5:19 PM Page e-11

Rear Panel Components and Controls

CAMERA IN (1~4)

This is CAMERA input connector.

MONITOR OUT

This is connector for outputting selected image signals.

AUDIO IN (1~4)

This is connector for inputting audio signals.

Select a connector of AUDIO IN with an appropriate number for each

number of CAMERA a input (1~4), for connection.

AUDIO OUT

This is connector for outputting selected audio signals.

(In Auto mode, this function is disabled.)

e-12

123

CAMERA IN

4

MONITOR

AUDIO OUT

OUT

12

43

AUDIO IN

1_SMC_142_eng 8/23/02 5:19 PM Page e-12

ページを読み込んでいます...

Samsung SMC-212H/CHN, SMC-142H/CHN 取扱説明書

関連論文

その他の書類