Supermicro SCGS50-000R ユーザーマニュアル

USER’S MANUAL

Revision 2.0

S5 ChASSiS

SCGS50-000R SCGS5B-000R

SCGS5A-754K

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software and

documentation, is the property of Supermicro and/or its licensors, and is supplied only under a

license. Any use or reproduction of this product is not allowed, except as expressly permitted by

the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all

claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class

B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instruction manual, may cause harmful

interference with radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference, in which case you will be required to correct the interference at your

own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: This product can expose you to chemicals including

lead, known to the State of California to cause cancer and birth

defects or other reproductive harm. For more information, go

to www.P65Warnings.ca.gov.

!

Manual Revision 2.0

Release Date: November 08, 2018 mk

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

iii

Preface

About this Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the chassis. Installation and

maintenance should be performed by experienced technicians only.

This document lists compatible parts available when this document was published.

Refer to the Supermicro web site f

Warnings

Special attention should be given to the following symbols used in this manual.

Warning! Indicates high voltage may be encountered when performing

a procedure.

Warning! Indicates important information given to prevent equipment/

property damage or personal injury.

iv

SCGS5 User's Manual

Contents

Contacting Supermicro ................................................................................................. 5

Chapter 1 Introduction ..............................................................................1-1

1-1 Overview ......................................................................................................... 1-1

Key Features ................................................................................................... 1-1

1-2 Components .................................................................................................... 1-2

Drives .............................................................................................................. 1-2

Fans and Cooling ............................................................................................ 1-2

Motherboard .................................................................................................... 1-2

Expansion Slots .............................................................................................. 1-2

External I/O Connections ................................................................................ 1-2

User Interface .................................................................................................. 1-2

1-3 Where to Get Replacement Components ....................................................... 1-3

1-4 Returning Merchandise for Service................................................................. 1-3

Chapter 2 Chassis Setup and Maintenance ...........................................2-1

2-1 Overview ......................................................................................................... 2-1

2-2 Removing Power from the System ................................................................. 2-2

2-3 Removing the Chassis Covers........................................................................ 2-3

Left Side and Right Side Covers .................................................................... 2-3

Front Bezel ...................................................................................................... 2-4

2-4 Installing Drives ............................................................................................... 2-5

2-5 Installing the Motherboard ............................................................................ 2-10

Installing the I/O Shield ................................................................................ 2-10

Motherboard Standoffs ...................................................................................2-11

Motherboard Installation .................................................................................2-11

2-6 Fans and Cooling .......................................................................................... 2-13

Air Flow ......................................................................................................... 2-15

Dust Filters .................................................................................................... 2-15

2-7 Installing Expansion Cards ........................................................................... 2-16

2-8 Power Supply ................................................................................................ 2-16

Appendix A Standardized Warning Statements for AC Systems

v

Preface

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Web Site: www.supermicro.nl

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3992

Email: [email protected]

Web Site: www.supermicro.com.tw

vi

SCGS5 User's Manual

Notes

Chapter 1

Introduction

1-1 Overview

Supermicro's S5 gaming chassis (SCGS5) offers extreme storage and cooling

opportunities in a sleek, attractive form. It can house a powerful ATX form factor

motherboard supporting outstanding gaming-level high performance.

Key Features

• Black anodized brushed aluminum fascia front panel with two USB 3.0 ports

• Removable 3.5” and 2.5” HDD/SSD cages with tool-less trays for up to 10 drives

• Tool-less 5.25” device installation with trays to support 3.5” and 2.5” drives

• Cable management holes with rubber grommets for clean builds

• 

• One click front grille access

• Large motherboard tray cut-out for CPU cooler back-plates

• Three 120mm PWM fans included

For the SCGS5B-000R model:

• Black interior paint throughout the chassis; best for DIY gamer

For the SCGS5A-754K model:

• Includes a 750W power supply (PWS-754-PQ)

• 

• All the cables are modular.

• A fan mode button on the power supply limits fan activity for quiet operation

• Includes noise absorbing foam on the side panels

Chapter 1 Introduction

1-1

SCGS5 Chassis Manual

1-2

1-2 Components

The primary components are described below.

Drives



six combination bays that can house either 3.5" or 2.5" drives.

• 

• The four 2.5" bays are housed in a removable cage.

• Two additional removable cages can each accommodate three 2.5" or 3.5"

drives.

Fans and Cooling

The chassis includes two 120mm PWM fans in the front and one 120mm PWM fan



• Two front fans can be upgraded to 140mm.

• Three fans can be mounted on the chassis top, 120mm or 140mm.

• Fans can be mounted on the chassis side, two 120mm or one 140mm. (Not

applicable for the SCGS5A-754K model.)

Motherboard

The chassis accepts ATX and Micro ATX form factor motherboards.

Expansion Slots

Seven PCI-E slots for expansion cards are available on the chassis rear. They

can also be used for Graphic Processor Units (GPUs). The maximum GPU length

depends on whether the dedicated 2.5" drive cage is installed--420mm without the

cage, 320mm with the cage.

External I/O Connections

The front of the chassis supports two USB 3.0 ports, a headphone port and a



Control Panel

The front control panel features a power on/off button with LED illumination, and

a reset button.

1-3

Chapter 1: Introduction

1-3 Where to Get Replacement Components

To ensure the highest level of professional service and technical support, we strongly

recommend purchasing exclusively from our Supermicro Authorized Distributors/

System Integrators/Resellers. A list of Supermicro Authorized Distributors/System

Integrators/Reseller can be found at: http://www.supermicro.com. Click the Where

to Buy link.

1-4 Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required before

any warranty service will be rendered. You can obtain service by calling your vendor

for a Returned Merchandise Authorization (RMA) number. When returning to the

manufacturer, the RMA number should be prominently displayed on the outside of

the shipping carton, and mailed prepaid or hand-carried. Shipping and handling

charges will be applied for all orders that must be mailed when service is complete.

For faster service, RMA authorizations may be requested online (http://www.

supermicro.com/support/rma/).

Whenever possible, repack the chassis in the original Supermicro carton, using the

original packaging material. If these are no longer available, be sure to pack the

chassis securely, using packaging material to surround the chassis so that it does

not shift within the carton and become damaged during shipping.

This warranty only covers normal consumer use and does not cover damages

incurred in shipping or from failure due to the alteration, misuse, abuse or improper

maintenance of products.



SCGS5 Chassis Manual

1-4

Notes

2-1

Chapter 2: Chassis Setup and Maintenance

Chapter 2

Chassis Setup and Maintenance

2-1 Overview

This chapter covers the steps required to install components and perform

maintenance on the chassis. Most tasks can be accomplished without tools.

Review the warnings and precautions listed in the manual before setting up or

servicing this chassis, including those in the system safety appendix.

Figure 2-1. Front and Rear View

S5 Chassis Manual

2-2

2-2 Removing Power from the System

Before performing most setup or maintenance tasks, use the following procedure

to ensure that power has been removed from the system.

1. Use the operating system to power down the system, following the on-screen

prompts.

2. After the system has completely shut-down, carefully grasp the head of the

power cord and gently pull it out of the back of the power supply.

3. Disconnect the cord from the power strip or wall outlet.

2-3

Chapter 2: Chassis Setup and Maintenance

2-3 Removing the Chassis Covers

Caution: Except for short periods of time, do not operate the system without the

              

prevent overheating.

Left Side and Right Side Covers

Removing a Side Chassis Cover

1. Power down the system as described in section 2-2.

2. Remove the two thumb screws on the rear of the chassis.

3. Slide the cover back toward the rear of the chassis.

Figure 2-2. Removing the Side Cover

S5 Chassis Manual

2-4

Front Bezel

Remove the front bezel by pulling it off from the bottom of the bezel. This should

only be necessary when replacing the front fans.

Figure 2-3. Removing the Front Bezel

2-5

Chapter 2: Chassis Setup and Maintenance

2-4 Installing Drives



six combination bays that can house either 3.5" or 2.5" drives.

• 

DVD, or a storage device, such as a 3.5" HDD, 2.5" HDD, or solid state drive.

• The four 2.5" bays are housed in a removable cage.

• Two additional removable cages can each accomodate three 2.5" or 3.5" drives.

Cage for

four 2.5"

drives

Combo

Cage for

three

drives

5.25' Bays

Figure 2-4. Drive Bays

Combo

Cage for

three

drives

S5 Chassis Manual

2-6

3. Push the drive tray toward the front of the chassis and out.

4. Slide the DVD drive into the chassis until it clicks into place.

Figure 2-5. Release Tabs for the Drive Tray

Installing a DVD Drive in the 5.25" Drive Bay

Replace a drive tray with a DVD drive.

1. Open the chassis left side cover.

2. Locate and press the release tab for the drive tray where you want to place

the DVD drive.

Release Tabs

2-7

Chapter 2: Chassis Setup and Maintenance

Figure 2-6. Storage Device Congurations for 5.25" Bays

Installing a Storage Device in the 5.25" Drive Tray

You can install a 3.5" drive, one or two 2.5" disk drives or solid state drives.

1. Open the chassis left side cover.

2. Locate and press the release tab (Figure 2-5) for the drive tray in which you

want to place the drive.

3. Push the drive tray toward the front of the chassis and out.

4. Secure the storage drive to the drive tray with screws through the bottom of the

tray. To install two 2.5" drives, use the optional bracket (P/N MCP-220-00044-

0N) as shown.

5. Slide the drive tray into the chassis until it clicks into place.

Optional Bracket for

two 2.5" drives

S5 Chassis Manual

2-8

Installing Disk Drives into the Cage

You can install up to four 2.5" drives into the dedicated center cage. You can also

install three drives into each of the upper and lower combination cages.

1. Open the chassis left side cover.

2. Remove the drive mounting bracket from the cage. Pinch the tabs and pull out.

3. Secure the drive into the mounting bracket.

Figure 2-7. Installing Drives and Mounting Brackets in to the Cage

2-9

Chapter 2: Chassis Setup and Maintenance

Figure 2-8. Mounting Tray for 3.5" Drive

Figure 2-9. Mounting Tray for 2.5" Drive

• 

and drop the drive in with the connector side facing into the chassis.

•              

bracket and drop the drive in with the connector side facing into the chassis.

• For 2.5" drives in the combo bays, use screws through the bottom of the

bracket to secure the drive with the connector side facing into the chassis.

4. Slide the assembly into the cage.

5. Connect the storage device cables from the motherboard.

S5 Chassis Manual

2-10

2-5 Installing the Motherboard

Installing the I/O Shield

The shield encloses the I/O ports at the rear of the chassis. Install it before installing

the motherboard. The motherboard package should include a compatible shield.

Installing the I/O Shield

1. Open the chassis left side cover.

2. With the illustrations facing outward, place the shield into the space provided

at the rear of the chassis.

I/O Shield

Figure 2-10. Installing the I/O Shield

ページが読み込まれています...

Supermicro SCGS50-000R ユーザーマニュアル

このマニュアルも適しています

Supermicro SCGS50-000R ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント