XBA-10
Stereo Headphones
Operating Instructions
使用說明書
4-439-626-12(1)
Precautions
High volume may affect your hearing.
For traffic safety, do not use while
driving or cycling.
Install the earbuds firmly. If an earbud
accidentally detaches and is left in
your ear, it may cause injury.
Do not leave the stereo headphones in a location
subject to direct sunlight, heat or moisture.
Note on static electricity
Static electricity accumulated in the body may cause
mild tingling in your ears.
To minimise the effect, wear clothes made from
natural materials.
Specifications
Type: Closed, Balanced Armature
Driver unit: Balanced Armature
Power handling capacity: 100 mW (IEC*)
Impedance: 24 Ω at 1 kHz
Sensitivity: 108 dB**
Frequency response: 5 Hz – 25,000 Hz
Cord: 1.2 m cord, using PCOCC (Y-type)
Plug: Gold-plated L-shaped stereo mini plug
Mass: Approx. 3 g (without cord)
Supplied accessories
Hybrid silicone rubber earbuds: SS (red) (2), S (orange)
(2), MS (yellow) (2), M (green) (attached to the unit at
the factory) (2), ML (blue) (2), L (light blue) (2), LL
(purple) (2) / Noise isolation earbuds: S (orange) (2), M
(green) (2), L (light blue) (2) / Cord adjuster (winds cord
up to 50 cm) (1) / Clip (1) / Carrying pouch (1)
* IEC = International Electrotechnical Commission
** 150 mV input
Design and specifications are subject to change
without notice.
Optional replacement earbuds can be ordered from
your nearest Sony dealer.
About noise isolation earbuds
Supplied noise isolation earbuds provide a snug fit for
effective attenuation of ambient noise.
How to use / 使用方法 /
©2012 Sony Corporation
Printed in Thailand
Notes
Prolonged use of snugly fitting earbuds may strain
your ears. If you experience discomfort, discontinue
use.
The pressure-relieving urethane cushion is
extremely soft. If it breaks or detaches from the
earbuds, it will not take its correct position and the
earbuds will lose their noise isolation function.
The urethane cushion may deteriorate over time. If
the pressure-relieving power is lost and the
urethane cushion hardens, the earbuds may lose
their noise isolation function.
Do not wash the earbuds. Keep them dry, otherwise
they may deteriorate quickly.
About hybrid silicone rubber earbuds
Keep earbuds clean. To clean the earbuds, wash them
with a mild detergent solution.
Removing the headphones
After use, remove the headphones slowly.
Note
Headphones are designed to fit closely in your ears. If
the headphones are pressed hard while in use or taken
off too quickly, they may cause injury.
Wearing headphones may produce a diaphragm click
sound. This is not a malfunction.
Clip / 線夾 /
Earbuds / 耳塞 /
Hybrid silicone rubber earbuds
混合矽膠耳塞
Noise isolation earbuds
噪音隔離耳塞
S M
Pressure-relieving
urethane cushion
氨基鉀酸酯釋壓泡棉
L
SS S MS M ML L LL
English Stereo headphones
Features
Balanced Armature driver unit
Micro-size Balanced Armature driver unit (full-range)
reproduces smooth and clear vocal sound.
High quality PCOCC cord
PCOCC cord to minimise sound transmission loss
and reproduce a clear high quality sound.
Double Layered Housing
Liquid Crystal Polymer inner housing and special
ABS outer housing reproduces clear, distortion-free
mid-high range.
Noise-Blocking design and various ear-bud sizes
Noise-Blocking design, with 10 sets of ear-buds to
choose from, for optimum attenuation of ambient
noise and minimum sound leakage.
Super-small body
Balanced Armature driver unit allows for a super
small body, and ultimate wearing comfort.
Serrated cord
Serrated cord and cord slider for tangle-free use.